PACIFIC SC9830AS ユーザーマニュアル

Model Number:

Read all instructions before operating the range hood.

SC9830AS, SC9836AS

OPERATING INSTRUCTION

PACIFIC RANGE HOOD

Airﬂ ow Control Technol og y

TM

C

331-01-000467(3) www.2pacific.com

Table of Content

www.2pacific.com

P1-3

Safety Information

P6

Circuit Diagram

P5

Parts Supplied

P7

P8

List of Materials

P9

Installation Guidelines

P10-13

Installation Procedures – Under Cabinet

Installation Procedures – Wall P14-17

Installation Instructions – Optional Duct Cover P18-21

P4

Product Functions / Performance Speciﬁcation Chart

P22-P24

Operating Instructions

P27

Features & Controls

P28

ACT™ Conversion

P29

Surface Maintenance

P30

Steam Clean Function Remarks

P25-p26

P31-33

Troubleshooting

Paciﬁc Kitchen + App Set Up

Installation Speciﬁcations

1www.2pacific.com

Safety Information

Your safety and the safety of others are very important.

We have provided many important safety messages in this

manual for your appliance. Always read and obey all safety

messages.

This is the Safety Alert Symbol. This symbol alerts you to

potential hazards that can cause severe bodily injury or death.

All safety messages will follow the Safety Alert Symbol and either

the words “DANGER” “WARNING” or “CAUTION”

DANGER

Danger means that failure to heed this safety statement may

result in severe injury or death.

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

General Safety

WARNING

Warning means that failure to heed this safety statement

may result in extensive product damage, serious personal

injury, or death.

CAUTION

Caution means that failure to heed this safety statement

may result in minor or moderate personal injury, property or

equipment damage.

WARNING

To reduce the risk of ﬁre or electric shock, do not use this fan

with any solid-state control device.

WARNING

CAUTION

For General Ventilating Use Only. Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors. Take care

when using cleaning agents or detergents. Suitable for use in

household cooking area.

WARNING

WARNING - TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

a) Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite.

Heat oils slowly on low or medium settings.

b) Always turn hood ON when cooking at high heat or

when ﬂambeing food. (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’).

c) Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or ﬁlter.

d) Use proper pan size. Always use cookware appropriate for

the size of the surface element.

2www.2pacific.com

Safety Information

WARNING

READ AND SAVE THESE INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or

BURNS. If the ﬂames do not go out immediately, EVACUATE AND

CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN – You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels – a

violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class ABC extinguisher, and you

already know how to operate it.

2) The ﬁre is small and contained in the area where it

started.

3) The ﬁre department is being called.

4) You can ﬁght the ﬁre with your back to an exit

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of ﬁre and to properly exhaust air outside, do

not vent exhaust air into spaces within walls, ceilings, attics,

crawl spaces, or garages.

WARNING

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable codes and

standards, including ﬁre-rated construction.

exhausting of gases through the ﬂue (chimney) of fuel burning

equipment to prevent back drafting. Follow the heating

equipment manufacturer’s guideline and safety standards such

as those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local code

authorities.

c) When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected

to a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit.

WARNING

Prop. 65 Warning for California Residents: This product may

contain chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

3www.2pacific.com

Safety Information

Operation

Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

NOTE: Please check www.2pacific.com for revisions before doing any custom work.

Electrical Requirements

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility to be aware of these below:

To contact a qualiﬁed electrical installer.

To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest

edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground

path is adequate.

Do not ground to a gas pipe.

Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and

install appropriate connector if necessary.

* National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

READ AND SAVE THESE INSTRUCTIONS

Product Functions

Performance Speciﬁcation Chart

4www.2pacific.com

SC9830AS

Weight (lbs)

Size 30”

55.6

36”

59.3

Color Stainless Steel

Model SC9836AS

Dimension (inch)

Maximum Voltage

Duct size

Lighting

Maximum comsumption

power

Maximum CFM

ACT™

120 V – 60 Hz

7 “Round (Vertical)

8.4A/920W

6W LED x 2

1200 CFM

290/390 CFM

WiFi Connection

35-11/16” x 11”

x 22-1/2” x 22-1/2”

x 11”29-3/4”

1. Automatic steam clean function

2. Turbo mode to quickly remove cooking fumes and smoke

3. Motion activation to turn on/off the range hood with a wave of your hand

4. Memory function to remember the last used fan and light settings

5. 3-min and 5-min automatic delay off

6. Built-in timer

7. Built-in air quality detector (AQI)

8. Airflow Control Technology (ACT™)

9. Compatible with Pacific Kitchen + App

10. Compatible with Google Home and Amazon Alexa

Installation Type

Google Home /Amazon Alexa

Under Cabinet / Wall-Mounted

Parts Supplied

5www.2pacific.com

(1) Oil Cup

(1) Bottom panel

(1) IR Switch assembly

(2) LED light

(1) Hood body

(1) 7" Collar

(1) Housing

(1) Hardware Packet

(1) Deflector Board

Circuit Diagram

6www.2pacific.com

CIRCUIT DIAGRAM

7

www.2pacific.com

Installation Speciﬁcations

Wall

Cabinet

Dimensional Drawing

Mounting Template

BackFront

Side

Top

Under Cabinet

List of Materials

8www.2pacific.com

Supplied

4

3

4

2

12

3/16 x 10" screws

Holder, Deflector Board

#6 x 2 " Wood screws

#6 x 1" Wood screws

P3 Wire nuts

#6 x 1-1/2" Wood screws

HARDWARE PACKAGE CONTENTS

1

2

10

M4*8 Screw

3

#6*1-1/2" Screw

2

Side Panel

1

12

Center Panel

M3.5*10 Screw

Bracket, Wall

Duct Cover, Lower

Bracket, Bottom

Duct Cover, Upper

ACCESSORIES(OPTIONAL)

TELESCOPIC DUCT COVER P1C-0098

12” DUCT COVER 30”-SC0930

36”-SC0936

1

5 x 24 x 1T washers 4

1

2

1

2

1

STANDARD CONFIGURATION

排油煙機使用說明書

型號

www.2pacific.com

(使用前，請先詳細閱讀此說明書)

SC9830AS/SC9836AS

太平洋油煙機

Manual

Oil cup

7”Collar

Hood

Mounting

Template

Mouting

bracket

Hardware

packet

Power

cord

Round

Rubber

Water

cap

Water

Refiller

Deflector

Board

(FIG.2)

Installation Guidelines

9www.2pacific.com

is 26”, and the maximum is 32". (FIG. 3)

•Avoid left-right or front-dropped inclination. (FIG. 2)

(FIG.3)

(FIG.1)

Air turbulence from window/door may reduce the effectiveness of hood.

Suggest to close window/door before using the hood .(FIG. 1)

•

•The installation height is measured vertically from the center of the

hood to the top of the cooktop.

•The minimum mount height between range top to hood bottom

•7 inches diameter exhaust duct is recommended to use in order to

maximize suction efficiency. 6 inches diameter exhaust duct is available,

but it might impact the suction efficiency.

• Install the range hood and exhaust duct to the plastic collar and seal with metal tape.

3.Exhaust duct

2.Mounting Height and Position

1.Location

26” min.

32” max.

36”

5.Reinforce cabinet bottom with wood strips if additional strengthening is

required.(see Fig. 3)

Wood

(Fig. 3)

Wood

Installation Instructions – Under Cabinet

10

www.2pacific.com

1.Open package to confirm contents and check product appearance.

2.Refer the mounting height on Page 9.

3.Locate the wooden beam and mark the location. (see Fig. 1)

(Fig. 1)

(Fig. 2)

4. Place the template at the desired location on the wall, and drill the holes as indicated

on the template, remove the template after all holes were drilled.

Place the "Cabinet" template facing down and stick it on the bottom of the

upper cabinet, drill holes according to the template, take down the template

(see Fig. 2)

after all holes were drilled.

7.Remove the bottom panel from the hood by using a Phillips head screwdriver

to remove each screw.

Use caution when removing the bottom panel. Be careful not to scratch

side panels during removal. (see Fig. 5)

Installation Instructions – Under Cabinet

11

www.2pacific.com

(Fig. 5)

6.Attach the mounting bracket to the wall using (6) #6 x 2”screws.(see Fig. 4)

(Fig. 4)

8.Install collar and duct work, then seal with aluminum duct tape. (see Fig. 6)

(Fig. 6)

9.Lift the hood and insert mounting bracket into (2) lower holes on the

hood's back panel. (see Fig. 7)

Installation Instructions – Under Cabinet

12

www.2pacific.com

(Fig. 8)

10.Install electrical.

11.Turn on the hood and check for any air leakage from the pipe around

duct tape and test all functions.

Push the hood against the bottom of cabinet and secure the hood

using (4) #6 screw to the drilled screw holes. (see Fig. 8)

(Fig. 7)

Wood Screws

Key Hole

13.Install the deflector board and oil cup.

Installation Instructions – Under Cabinet

13

www.2pacific.com

(Fig. 10)

(Fig. 9)

12.Reinstall bottom panel. Use caution when installing bottom panel.

Be careful not to scratch side panels during installation.(see Fig. 9)

Press the left and right side clip to engage the deflector board with clip holder.(see Fig. 10)

4.Attach the round rubbers on the lower back panel of the hood. (see Fig. 2)

Installation Instructions – Wall

14

www.2pacific.com

1.Open package to confirm contents and check product appearance.

2.Refer the mounting height on Page 9.

3. Locate the wooden beam and mark the location. (see Fig. 1)

(Fig. 1)

(Fig. 2)

Round Rubber

5.Remove bottom panel from hood using a Philips head screwdriver to remove each of the screws.

Use caution when removing the bottom panel. Be careful not to scratch side panels during removal.

(see Fig. 3)

Installation Instructions – Wall

15

www.2pacific.com

(Fig. 3)

6.Install collar and duct work, then seal with aluminum duct tape. (see Fig. 4)

(Fig. 4)

Installation Instructions – Wall

16

www.2pacific.com

(Fig. 5)

7.Then fasten (2) 6# x 2”screws with (2) 5 x 24 x 1T washers into wall on the back panel of the hood.

(see Fig. 5)

(Fig. 6)

10.Reinstall bottom panel. Use caution when installing bottom panel.

Be careful not to scratch side panels during installation. (see Fig. 6)

9.Turn on the hood and check for any air leakage from the pipe around duct tape and

test all functions.

8.Install electrical.

11.Install the deflector board and oil cup.

Installation Instructions – Wall

17

www.2pacific.com

(Fig. 7)

Press the left and right side clip to engage the deflector board with clip holder.(see Fig. 7)

Installation Instructions – Optional Duct Cover

18

www.2pacific.com

1. Attach the bottom bracket on the top of hood using (2) M4x8 screws

to secure on each side.

Optional Duct Cover : 30-9/16"- 57-3/16"

Model #: P1C-0098

Note: P1C-0098 is not supplied in the package, To order it,

please visit us online at www.2pacific.com or call 888-833-8833.

P1C-0098 Duct cover

Installation

ページを読み込んでいます...

PACIFIC SC9830AS ユーザーマニュアル

関連論文

その他の書類