Mitsubishi Electric GT21 (GT2105-QTBDS, GT2105-QMBDS) 取扱説明書

ブランド: Mitsubishi Electric

モデル: GT21 (GT2105-QTBDS, GT2105-QMBDS)

タイプ: 取扱説明書

This manual confers no industrial property rights or any rights of any other

kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation

cannot be held responsible for any problems involving industrial property rights

which may occur as a result of using the contents noted in this manual.

Warranty

Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for

compensation to:

(1) Damages caused by any cause found not to be the responsibility of

Mitsubishi.

(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi

products.

(3) Special damages and secondary damages whether foreseeable or not,

compensation for accidents, and compensation for damages to products

other than Mitsubishi products.

(4) Replacement by the user, maintenance of on-site equipment, start-up test run

and other tasks.

For safe use

This product has been manufactured as a general-purpose part for general

industries, and has not been designed or manufactured to be incorporated in

a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric

power, aerospace, medicine or passenger movement vehicles, consult with

Mitsubishi Electric.

This product has been manufactured under strict quality control. However

when installing the product where major accidents or losses could occur if the

product fails, install appropriate backup or failsafe functions in the system.



HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Side

ENGLISH

CHINESE

JY997D66601B

Side

Safety Precaution

(Read these precautions before using.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and

"CAUTION".

Depending on circumstances, procedures indicated by "CAUTION" may also be

linked to serious results. In any case, it is important to follow the directions for

usage.

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury

or physical damage.

DESIGN PRECAUTIONS

 Some failures of the GOT or cable may keep the outputs on or off. Some

failures of a touch panel may cause malfunction of the input objects such as a

touch switch. An external monitoring circuit should be provided to check for

output signals which may lead to a serious accident. Not doing so can cause

an accident due to false output or malfunction.

 Do not use the GOT as the warning device that may cause a serious

accident. An independent and redundant hardware or mechanical interlock is

required to configure the device that displays and outputs serious warning.

Not doing so can cause an accident due to false output or malfunction.

 When the GOT detects its backlight failure, the GOT disables the input

operation on the touch switch(s). Thus, operators cannot operate the GOT

with touches. The GOT backlight failure can be checked with a system signal

of the GOT.

 Incorrect operation of the touch switch(s) may lead to a serious accident if the

GOT backlight is gone out.

When the GOT backlight goes out, the POWER LED blinks (blue/orange) and

the display section dims, while the input of the touch switch(s) remains active.

This may confuse an operator in thinking that the GOT is in "screensaver"

mode, who then tries to release the GOT from this mode by touching the

display section, which may cause a touch switch to operate.

 The display section of the GOT is an analog-resistive type touch panel.

Simultaneous pressing of two or more areas on the display section may

activate the switch between those areas. Do not press two or more areas

simultaneously on the display section. Doing so may cause an accident due

to incorrect output or malfunction.

 When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to shut off the power of the GOT

promptly and power on the GOT again. Not doing so can cause an accident

due to false output or malfunction.

 If a communication fault (including cable disconnection) occurs during

monitoring on the GOT, communication between the GOT and PLC CPU is

suspended and the GOT becomes inoperative. A system where the GOT is

used should be configured to perform any significant operation to the system

by using the switches of a device other than the GOT on the assumption that

a GOT communication fault will occur. Not doing so can cause an accident

due to false output or malfunction.

DESIGN PRECAUTIONS

 When the security of the GOT and relevant information need to be protected

against illegal access from an external device via the Internet, take measures at

the user's discretion.

Failure to do so may cause the configured information to be read out illegally.

DESIGN PRECAUTIONS

 Do not bundle the control and communication cables with main-circuit, power or

other wiring. Run the above cables separately from such wiring and keep them a

minimum of 100 mm apart. Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

 Turn on the controllers and the network devices to be ready for communication

before they communicate with the GOT. Failure to do so can cause a

communication error on the GOT.

 When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

MOUNTING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the GOT main unit to/from the panel. Not doing so

can cause the unit to fail or malfunction.

MOUNTING PRECAUTIONS

 Use the GOT in the environment that satisfies the general specifications

described in this manual. Not doing so can cause an electric shock, fire,

malfunction or product damage or deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in the

specified torque range (0.3 N·m to 0.5 N·m) can cause the GOT to drop, short

circuit or malfunction. Overtightening can cause a drop, short circuit or

malfunction due to the damage of the screws or the GOT.

 Remove the protective film of the GOT. When the user continues using the GOT

with the protective film, the film may not be removed.

 Operate and store the GOT in environments without direct sunlight, high

temperature, dust, humidity, and vibrations.

 Do not use the GOT in an environment with oil or chemicals. Doing so may cause

failure or malfunction due to the oil or chemical entering into the GOT.

WIRING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before wiring. Failure to do so may result in an electric shock, product damage or

malfunctions.

WIRING PRECAUTIONS

 Please make sure to ground FG terminal of the GOT power supply section by

applying 100 Ω or less which is used exclusively for the GOT. Not doing so may

cause an electric shock or malfunction.

 Correctly wire the GOT power supply section after confirming the rated voltage

and terminal arrangement of the product. Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.5 N·m to 0.8 N·m). Undertightening can cause a short circuit or

malfunction. Overtightening can cause a short circuit or malfunction due to the

damage of the screws or the GOT.

 For a terminal processing of a wire to the GOT power supply section, connect a

stranded wire or a single wire directly, or use a rod terminal with an insulation

sleeve.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering the

GOT. Not doing so can cause a fire, failure or malfunction.

 Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in the

specified torque range. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction dueto the damage of the

screws or unit.

TEST OPERATION

PRECAUTIONS

 Before performing the test operations of the user creation monitor screen (such as

turning ON or OFF bit device, changing the word device current value, changing

the settings or current values of the timer or counter, and changing the buffer

memory current value), read through the manual carefully and make yourself

familiar with the operation method. During test operation, never change the data

of the devices which are used to perform significant operation for the system.

False output or malfunction can cause an accident.

Manual

The following shows manuals relevant to this product.

Detailed Manual

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the

drawing software used.

Relevant Manuals

For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM

for the drawing software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (http://www.MitsubishiElectric.co.jp/fa).

Before using the GOT

Refer to the GOT2000 Series User’s Manual (Hardware) for the connection

instructions.

For details on the GOT specifications, installing instructions, wiring, maintenance

and inspection, or checking procedure for the version and the compatible standard,

refer to the GOT2000 Series User’s Manual (Hardware).

Bundled Items

STARTUP/MAINTENANCE

PRECAUTIONS

 When power is on, do not touch the terminals. Doing so can cause an electric

shock or malfunction.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases. Not doing so can cause the unit to fail or

malfunction. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

STARTUP/MAINTENANCE

PRECAUTIONS

 Do not disassemble or modify the unit. Doing so can cause a failure,

malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly. Doing so

can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped. Not doing so

can cause the unit or cable to be damaged due to the dangling, motion or

accidental pulling of the cables or can cause a malfunction due to a cable

connection fault.

 When unplugging the cable connected to the unit, do not hold and pull from the

cable portion. Doing so can cause the unit or cable to be damaged or can cause

a malfunction due to a cable connection fault.

 Do not drop the module or subject it to strong shock. A module damage may

result.

 Before touching the unit, always touch grounded metals, etc. to discharge static

electricity from human body, etc. Not doing so can cause the unit to fail or

malfunction.

 Replace battery with GT11-50BAT by Mitsubishi electric Co. only.

Use of another battery may present a risk of fire or explosion.

 Dispose of used battery promptly.

Keep away from children. Do not disassemble and do not dispose of in fire.

TOUCH PANEL

PRECAUTIONS

 For the analog-resistive film type touch panels, normally the adjustment is not

required. However, the difference between a touched position and the object

position may occur as the period of use elapses. When any difference between

a touched position and the object position occurs, execute the touch panel

calibration.

 When any difference between a touched position and the object position occurs,

other object may be activated. This may cause an unexpected operation due to

incorrect output or malfunction.

PRECAUTIONS WHEN THE

DATA STORAGE IS IN USE

 If the SD card mounted on drive A of the GOT is removed while the GOT is

accessed, processing for the GOT might be interrupted about for 20 seconds.

The GOT cannot be operated during this period. The functions that run in the

background including a screen updating, alarm, logging, scripts, and others are

also interrupted. Since this interruption makes an impact to the system

operation, it might cause failure. After inhibiting access to the SD card on the

GOT utility screen, check that the SD card access LED is off and remove the SD

card.

 If the data storage mounted on the GOT is removed while the GOT is accessed,

the data storage and files are damaged. To remove the data storage from the

GOT, check that the access to the data storage in SD card access LED, the

system signal, and others is not performed.

 Turning off the GOT while it accesses the SD card results in damage to the SD

card and files.

 When removing the SD card from the GOT, make sure to support the SD card

by hand as it may pop out. Failure to do so may cause the SD card to drop from

the GOT, resulting in a failure or break.

 Before removing the SD card from the GOT, follow the procedure for removal on

the utility screen of the GOT. After the successful completion dialog is displayed,

remove the SD card by hand carefully. Failure to do so may cause the SD card

to drop from the GOT, resulting in a failure or break.

DISPOSAL PRECAUTIONS

 When disposing of this product, treat it as industrial waste.

 When disposing of batteries, separate them from other wastes according to the

local regulations.

(Refer to the GOT2000 Series User’s Manual for details of the battery directive

in the EU member states.)

TRANSPORTATION

PRECAUTIONS

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

regulated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner

they will not be exposed to the impact exceeding the impact resistance

described in the general specifications of this manual, as they are precision

devices. Failure to do so may cause the unit to fail. Check if the unit operates

correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden packaging

from insects, they cause malfunction when entering our products. Please take

necessary precautions to ensure that remaining materials from fumigant do not

enter our products, or treat packaging with methods other than fumigation (heat

method). Additionally, disinfect and protect wood from insects before packing

products.

Manual name

Manual number

(Model code)

GOT2000 Series User’s Manual (Hardware) SH-081194ENG (1D7MJ5)

GOT2000 Series User’s Manual (Utility) SH-081195ENG (1D7MJ6)

Model name Remark

GT2105-QTBDS,

GT2105-QMBDS

GOT main unit

(The maintenance supplies below are packed with the product.)

Model name Remark

Panel Mounting Bracket (with M4 × 35 screws) 4

Panel Mounting Packing 1

GT21 General Description (This manual) 1

1. GOT series User's Manual Specifications

1.1 General Specifications

*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.

*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90% at 40°C.

*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside

the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may

come off.

*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the

machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment

with the rated voltage up to 300 V is 2500 V.

*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-

conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.

1.2 Performance Specifications

*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as

the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to

individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.

*2 Flicker may occur due to vibration, shock, or display color.

*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.

Item Specifications

Operating ambient temperature

0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)

Storage ambient temperature -20 to 60C

Operating ambient humidity

10% RH to 90% RH, non-condensing

Storage ambient humidity

10% RH to 90% RH, non-condensing

Vibration resistance

Compliant with

JIS B3502 and

IEC61131-2

Frequency Acceleration Half amplitude Sweep Count

Under intermittent

vibration

5 to 8.4 Hz - 3.5 mm

10 times in each X,

Y, o r Z d i r e c t i o n

8.4 to 150 Hz

9.8m/s

Under continuous

vibration

5 to 8.4 Hz - 1.75 mm

8.4 to 150 Hz

4.9m/s

Shock resistant

Compliant with JIS B3502 and IEC61131-2 147m/s

(15G) Three times in each X, Y, or Z direction

Operating atmosphere No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)

Operating altitude

2000 m or less

Installation location Inside control panel

Overvoltage category

 or less

Pollution degree

2 or less

Cooling method Self-cooling

Grounding

Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a diameter of 1.6 mm or more.

If impossible, connect the ground cable to the control panel.

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Display section

*1*2

Display device TFT color display TFT monochrome display

Screen size 5.7"

Resolution 320 × 240 dots

Display size 115(4.53) (W) × 86(3.39) (H) mm(inch)

Displayed number of characters

16-dot standard font: 20 characters × 15 lines (two-byte characters)

12-dot standard font: 26 characters × 20 lines (two-byte characters)

Display color Color (65536 colors) Monochrome (black/white) 32 shade grayscale

Brightness Adjustment 32 levels

Backlight LED (Not replaceable)

Backlight life

Approx. 65000 h (operating ambient temperature: 25°C, display intensity: 50%)

Touch panel

Type Analog resistive film

Key size Minimum 2 × 2 dots (per a key)

Simultaneous press

Simultaneous press prohibited

(only 1 point can be pressed)

Life 1 million times or more (Operating force: 0.98 N or less)

User memory capacity

User memory capacity Memory for storage (ROM): 9 MB

Life (number of write times) 100000 times

Battery GT11-50BAT lithium battery

Life Approx. 5 years (operating ambient temperature: 25°C)

Built-in interface

RS-232

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(male)

RS-422/485

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(female)

Terminating resistor

: OPEN/110 Ω/330 Ω (Switched with the terminating resistor setting switch)

USB (Device)

1 ch

Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B

SD card 1 channel SDHC card supported (max. 32 GB)

Buzzer output Single tone (tone length adjustable)

Productive structure

Outside the enclosure: IP67F

Inside the enclosure: IP2X

External dimensions 164(6.46) (W) × 135(5.32) (H) × 55(2.17) (D)

Panel cut dimensions 153(6.03) (W) × 121(4.77) (H)

Weight (excluding a fitting) Approx. 0.7 kg

Compatible software package GT Works3 Version1.144A or later

*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)

- Material: Polyacetal resin

- Tip radius: 0.8 mm or more

*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more

points on the touch panel simultaneously.

*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.

*7 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over

for a long time or where oil mist is filled.

1.3 Power Supply Specifications

2. Wiring of connection cable

For details of the connection cable, refer to the following manual.

 GOT2000 Series Connection Manual (Mitsubishi Products) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 1) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 2) For GT Works3

Version1

 GOT2000 Series Connection Manual (Microcomputers, MODBUS/Fieldbus

Products, Peripherals) For GT Works3 Version1

Certification of UL, cUL standards

 Using GOT

GOT is for use on a Flat Surface of a Type 1 Enclosure.

Notification of CE marking

The following products have shown compliance through direct testing (to the

identified standards) and design analysis (forming a technical construction file) to the

European Directive for Electromagnetic Compatibility (2014/30/EU) when used as

directed by the appropriate documentation.

 This product is designed for use in industrial applications

- Type: Graphic Operation Terminal

- Models: GOT series

For more details please contact your local Mitsubishi Electric sales site.

For details of CE marking, refer to the following.

GOT2000 series User's Manual

Notes for compliance to EMC regulation

1) General notes on the use of communication cables

Any device which utilizes a data communication function is susceptible to the

wider effects of local EMC noise. Therefore, when installing any communication

cables care should always be taken with the routing and location of those cables.

The GOT units identified on the previous chapter are compliant with the EMC

requirement when the following communication cables are used.

2) General notes on Power supply

The GT2105-QTBDS and GT2105-QMBDS unit

requires an additional ferrite filter to be attached to

the 24V DC power supply cables. The filter should

be attached in a similar manner as shown in the

figure opposite, i.e. the power cables are wrapped

around the filter. However, as with all EMC

situations the more correctly applied precautions

the better the systems Electro-magnetic

Compatibility. The ferrite recommended is a TDK

ZCAT3035-1330 or similar. The ferrite should be

placed as near to the 24V DC terminals of the

GT2105-QTBDS and GT2105-QMBDS as

possible (which should be within 75mm of the

GOT terminal).

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Input power supply voltage DC24 V (+10%, -15%)

Power

consumption

Under the

maximum load

4.5 W or less 2.9 W or less

At backlight off 2.2 W or less 2.2 W or less

Inrush current 27 A or less (2ms, 25°C, at the maximum load)

Permissible instantaneous power

failure time

Within 5ms

Noise immunity Noise voltage: 1000 Vp-p, Noise width: 1 μs (by noise simulator of 30 to 100 Hz noise frequency)

Dielectric withstand voltage 500 VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Insulation resistance 10 MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Electrical wire size

For power supply: 0.75[mm

] or more, For grounding: 2[mm

] or more

Ferrules with plastic sleeve Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A

Tightening torque (terminal screws) 0.5 to 0.8 N·m

Standard Remark

EN61131-2 : 2007

Programmable

controllers -

Equipment,

requirements and

tests

EMI

Compliance with all relevant aspects of the standard.

(Radiated Emissions)

EMS

Compliance with all relevant aspects of the standard.

(ESD, RF electromagnetic field, EFTB, Surge, RF

conducted disturbances and Power frequency

magnetic field)

GOT Unit Existing Cables User Made Cables

GT2105-QTBDS

and

GT2105-QMBDS

Ex. GT01-C30R4-8P

(as shown in EX.1)

A complete list of appropriate

cables can be found in the

GOT user's manual.

3rd party cables need to be

independently tested by the

user to demonstrate EMC

compliance.

100mm

250mm

140mm

GT01-C30R4-8P

Comes equipped

Added by user

GOT units

Programmable

controller

Added by user

(9.84inch)

(3.93inch)

(5.51inch)

Ex.1

F = Ferrite core

Ex. NEC TOKIN - ESD-R-17S or similar

F F F

Up to

75mm

(2.95inch)

GT2105-QTBDS, GT2105-QMBDS

GT21 General Description

This manual describes the part names, dimensions, mounting, and specifications

of the product. Before use, read this manual and manuals of relevant products

fully to acquire proficiency in handling and operating the product. Make sure to

learn all the product information, safety information, and precautions.

And, store this manual in a safe place so that you can take it out and read it

whenever necessary. Always forward it to the end user.

Registration

Ethernet is a trademark of Xerox Corporation in the United States. The company

name and the product name to be described in this manual are the registered

trademarks or trademarks of each company.

Effective Sep. 2016

Specifications are subject to change without notice.

 2016 Mitsubishi Electric Corporation

Manual Number JY997D66601B

Date Sep. 2016

This manual confers no industrial property rights or any rights of any other

kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation

cannot be held responsible for any problems involving industrial property rights

which may occur as a result of using the contents noted in this manual.

Warranty

Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for

compensation to:

(1) Damages caused by any cause found not to be the responsibility of

Mitsubishi.

(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi

products.

(3) Special damages and secondary damages whether foreseeable or not,

compensation for accidents, and compensation for damages to products

other than Mitsubishi products.

(4) Replacement by the user, maintenance of on-site equipment, start-up test run

and other tasks.

For safe use

This product has been manufactured as a general-purpose part for general

industries, and has not been designed or manufactured to be incorporated in

a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric

power, aerospace, medicine or passenger movement vehicles, consult with

Mitsubishi Electric.

This product has been manufactured under strict quality control. However

when installing the product where major accidents or losses could occur if the

product fails, install appropriate backup or failsafe functions in the system.



HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Side

ENGLISH

CHINESE

JY997D66601B

Side

Safety Precaution

(Read these precautions before using.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and

"CAUTION".

Depending on circumstances, procedures indicated by "CAUTION" may also be

linked to serious results. In any case, it is important to follow the directions for

usage.

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury

or physical damage.

DESIGN PRECAUTIONS

 Some failures of the GOT or cable may keep the outputs on or off. Some

failures of a touch panel may cause malfunction of the input objects such as a

touch switch. An external monitoring circuit should be provided to check for

output signals which may lead to a serious accident. Not doing so can cause

an accident due to false output or malfunction.

 Do not use the GOT as the warning device that may cause a serious

accident. An independent and redundant hardware or mechanical interlock is

required to configure the device that displays and outputs serious warning.

Not doing so can cause an accident due to false output or malfunction.

 When the GOT detects its backlight failure, the GOT disables the input

operation on the touch switch(s). Thus, operators cannot operate the GOT

with touches. The GOT backlight failure can be checked with a system signal

of the GOT.

 Incorrect operation of the touch switch(s) may lead to a serious accident if the

GOT backlight is gone out.

When the GOT backlight goes out, the POWER LED blinks (blue/orange) and

the display section dims, while the input of the touch switch(s) remains active.

This may confuse an operator in thinking that the GOT is in "screensaver"

mode, who then tries to release the GOT from this mode by touching the

display section, which may cause a touch switch to operate.

 The display section of the GOT is an analog-resistive type touch panel.

Simultaneous pressing of two or more areas on the display section may

activate the switch between those areas. Do not press two or more areas

simultaneously on the display section. Doing so may cause an accident due

to incorrect output or malfunction.

 When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to shut off the power of the GOT

promptly and power on the GOT again. Not doing so can cause an accident

due to false output or malfunction.

 If a communication fault (including cable disconnection) occurs during

monitoring on the GOT, communication between the GOT and PLC CPU is

suspended and the GOT becomes inoperative. A system where the GOT is

used should be configured to perform any significant operation to the system

by using the switches of a device other than the GOT on the assumption that

a GOT communication fault will occur. Not doing so can cause an accident

due to false output or malfunction.

DESIGN PRECAUTIONS

 When the security of the GOT and relevant information need to be protected

against illegal access from an external device via the Internet, take measures at

the user's discretion.

Failure to do so may cause the configured information to be read out illegally.

DESIGN PRECAUTIONS

 Do not bundle the control and communication cables with main-circuit, power or

other wiring. Run the above cables separately from such wiring and keep them a

minimum of 100 mm apart. Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

 Turn on the controllers and the network devices to be ready for communication

before they communicate with the GOT. Failure to do so can cause a

communication error on the GOT.

 When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

MOUNTING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the GOT main unit to/from the panel. Not doing so

can cause the unit to fail or malfunction.

MOUNTING PRECAUTIONS

 Use the GOT in the environment that satisfies the general specifications

described in this manual. Not doing so can cause an electric shock, fire,

malfunction or product damage or deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in the

specified torque range (0.3 N·m to 0.5 N·m) can cause the GOT to drop, short

circuit or malfunction. Overtightening can cause a drop, short circuit or

malfunction due to the damage of the screws or the GOT.

 Remove the protective film of the GOT. When the user continues using the GOT

with the protective film, the film may not be removed.

 Operate and store the GOT in environments without direct sunlight, high

temperature, dust, humidity, and vibrations.

 Do not use the GOT in an environment with oil or chemicals. Doing so may cause

failure or malfunction due to the oil or chemical entering into the GOT.

WIRING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before wiring. Failure to do so may result in an electric shock, product damage or

malfunctions.

WIRING PRECAUTIONS

 Please make sure to ground FG terminal of the GOT power supply section by

applying 100 Ω or less which is used exclusively for the GOT. Not doing so may

cause an electric shock or malfunction.

 Correctly wire the GOT power supply section after confirming the rated voltage

and terminal arrangement of the product. Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.5 N·m to 0.8 N·m). Undertightening can cause a short circuit or

malfunction. Overtightening can cause a short circuit or malfunction due to the

damage of the screws or the GOT.

 For a terminal processing of a wire to the GOT power supply section, connect a

stranded wire or a single wire directly, or use a rod terminal with an insulation

sleeve.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering the

GOT. Not doing so can cause a fire, failure or malfunction.

 Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in the

specified torque range. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction dueto the damage of the

screws or unit.

TEST OPERATION

PRECAUTIONS

 Before performing the test operations of the user creation monitor screen (such as

turning ON or OFF bit device, changing the word device current value, changing

the settings or current values of the timer or counter, and changing the buffer

memory current value), read through the manual carefully and make yourself

familiar with the operation method. During test operation, never change the data

of the devices which are used to perform significant operation for the system.

False output or malfunction can cause an accident.

Manual

The following shows manuals relevant to this product.

Detailed Manual

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the

drawing software used.

Relevant Manuals

For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM

for the drawing software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (http://www.MitsubishiElectric.co.jp/fa).

Before using the GOT

Refer to the GOT2000 Series User’s Manual (Hardware) for the connection

instructions.

For details on the GOT specifications, installing instructions, wiring, maintenance

and inspection, or checking procedure for the version and the compatible standard,

refer to the GOT2000 Series User’s Manual (Hardware).

Bundled Items

STARTUP/MAINTENANCE

PRECAUTIONS

 When power is on, do not touch the terminals. Doing so can cause an electric

shock or malfunction.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases. Not doing so can cause the unit to fail or

malfunction. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

STARTUP/MAINTENANCE

PRECAUTIONS

 Do not disassemble or modify the unit. Doing so can cause a failure,

malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly. Doing so

can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped. Not doing so

can cause the unit or cable to be damaged due to the dangling, motion or

accidental pulling of the cables or can cause a malfunction due to a cable

connection fault.

 When unplugging the cable connected to the unit, do not hold and pull from the

cable portion. Doing so can cause the unit or cable to be damaged or can cause

a malfunction due to a cable connection fault.

 Do not drop the module or subject it to strong shock. A module damage may

result.

 Before touching the unit, always touch grounded metals, etc. to discharge static

electricity from human body, etc. Not doing so can cause the unit to fail or

malfunction.

 Replace battery with GT11-50BAT by Mitsubishi electric Co. only.

Use of another battery may present a risk of fire or explosion.

 Dispose of used battery promptly.

Keep away from children. Do not disassemble and do not dispose of in fire.

TOUCH PANEL

PRECAUTIONS

 For the analog-resistive film type touch panels, normally the adjustment is not

required. However, the difference between a touched position and the object

position may occur as the period of use elapses. When any difference between

a touched position and the object position occurs, execute the touch panel

calibration.

 When any difference between a touched position and the object position occurs,

other object may be activated. This may cause an unexpected operation due to

incorrect output or malfunction.

PRECAUTIONS WHEN THE

DATA STORAGE IS IN USE

 If the SD card mounted on drive A of the GOT is removed while the GOT is

accessed, processing for the GOT might be interrupted about for 20 seconds.

The GOT cannot be operated during this period. The functions that run in the

background including a screen updating, alarm, logging, scripts, and others are

also interrupted. Since this interruption makes an impact to the system

operation, it might cause failure. After inhibiting access to the SD card on the

GOT utility screen, check that the SD card access LED is off and remove the SD

card.

 If the data storage mounted on the GOT is removed while the GOT is accessed,

the data storage and files are damaged. To remove the data storage from the

GOT, check that the access to the data storage in SD card access LED, the

system signal, and others is not performed.

 Turning off the GOT while it accesses the SD card results in damage to the SD

card and files.

 When removing the SD card from the GOT, make sure to support the SD card

by hand as it may pop out. Failure to do so may cause the SD card to drop from

the GOT, resulting in a failure or break.

 Before removing the SD card from the GOT, follow the procedure for removal on

the utility screen of the GOT. After the successful completion dialog is displayed,

remove the SD card by hand carefully. Failure to do so may cause the SD card

to drop from the GOT, resulting in a failure or break.

DISPOSAL PRECAUTIONS

 When disposing of this product, treat it as industrial waste.

 When disposing of batteries, separate them from other wastes according to the

local regulations.

(Refer to the GOT2000 Series User’s Manual for details of the battery directive

in the EU member states.)

TRANSPORTATION

PRECAUTIONS

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

regulated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner

they will not be exposed to the impact exceeding the impact resistance

described in the general specifications of this manual, as they are precision

devices. Failure to do so may cause the unit to fail. Check if the unit operates

correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden packaging

from insects, they cause malfunction when entering our products. Please take

necessary precautions to ensure that remaining materials from fumigant do not

enter our products, or treat packaging with methods other than fumigation (heat

method). Additionally, disinfect and protect wood from insects before packing

products.

Manual name

Manual number

(Model code)

GOT2000 Series User’s Manual (Hardware) SH-081194ENG (1D7MJ5)

GOT2000 Series User’s Manual (Utility) SH-081195ENG (1D7MJ6)

Model name Remark

GT2105-QTBDS,

GT2105-QMBDS

GOT main unit

(The maintenance supplies below are packed with the product.)

Model name Remark

Panel Mounting Bracket (with M4 × 35 screws) 4

Panel Mounting Packing 1

GT21 General Description (This manual) 1

1. GOT series User's Manual Specifications

1.1 General Specifications

*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.

*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90% at 40°C.

*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside

the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may

come off.

*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the

machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment

with the rated voltage up to 300 V is 2500 V.

*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-

conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.

1.2 Performance Specifications

*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as

the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to

individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.

*2 Flicker may occur due to vibration, shock, or display color.

*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.

Item Specifications

Operating ambient temperature

0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)

Storage ambient temperature -20 to 60C

Operating ambient humidity

10% RH to 90% RH, non-condensing

Storage ambient humidity

10% RH to 90% RH, non-condensing

Vibration resistance

Compliant with

JIS B3502 and

IEC61131-2

Frequency Acceleration Half amplitude Sweep Count

Under intermittent

vibration

5 to 8.4 Hz - 3.5 mm

10 times in each X,

Y, o r Z d i r e c t i o n

8.4 to 150 Hz

9.8m/s

Under continuous

vibration

5 to 8.4 Hz - 1.75 mm

8.4 to 150 Hz

4.9m/s

Shock resistant

Compliant with JIS B3502 and IEC61131-2 147m/s

(15G) Three times in each X, Y, or Z direction

Operating atmosphere No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)

Operating altitude

2000 m or less

Installation location Inside control panel

Overvoltage category

 or less

Pollution degree

2 or less

Cooling method Self-cooling

Grounding

Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a diameter of 1.6 mm or more.

If impossible, connect the ground cable to the control panel.

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Display section

*1*2

Display device TFT color display TFT monochrome display

Screen size 5.7"

Resolution 320 × 240 dots

Display size 115(4.53) (W) × 86(3.39) (H) mm(inch)

Displayed number of characters

16-dot standard font: 20 characters × 15 lines (two-byte characters)

12-dot standard font: 26 characters × 20 lines (two-byte characters)

Display color Color (65536 colors) Monochrome (black/white) 32 shade grayscale

Brightness Adjustment 32 levels

Backlight LED (Not replaceable)

Backlight life

Approx. 65000 h (operating ambient temperature: 25°C, display intensity: 50%)

Touch panel

Type Analog resistive film

Key size Minimum 2 × 2 dots (per a key)

Simultaneous press

Simultaneous press prohibited

(only 1 point can be pressed)

Life 1 million times or more (Operating force: 0.98 N or less)

User memory capacity

User memory capacity Memory for storage (ROM): 9 MB

Life (number of write times) 100000 times

Battery GT11-50BAT lithium battery

Life Approx. 5 years (operating ambient temperature: 25°C)

Built-in interface

RS-232

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(male)

RS-422/485

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(female)

Terminating resistor

: OPEN/110 Ω/330 Ω (Switched with the terminating resistor setting switch)

USB (Device)

1 ch

Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B

SD card 1 channel SDHC card supported (max. 32 GB)

Buzzer output Single tone (tone length adjustable)

Productive structure

Outside the enclosure: IP67F

Inside the enclosure: IP2X

External dimensions 164(6.46) (W) × 135(5.32) (H) × 55(2.17) (D)

Panel cut dimensions 153(6.03) (W) × 121(4.77) (H)

Weight (excluding a fitting) Approx. 0.7 kg

Compatible software package GT Works3 Version1.144A or later

*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)

- Material: Polyacetal resin

- Tip radius: 0.8 mm or more

*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more

points on the touch panel simultaneously.

*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.

*7 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over

for a long time or where oil mist is filled.

1.3 Power Supply Specifications

2. Wiring of connection cable

For details of the connection cable, refer to the following manual.

 GOT2000 Series Connection Manual (Mitsubishi Products) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 1) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 2) For GT Works3

Version1

 GOT2000 Series Connection Manual (Microcomputers, MODBUS/Fieldbus

Products, Peripherals) For GT Works3 Version1

Certification of UL, cUL standards

 Using GOT

GOT is for use on a Flat Surface of a Type 1 Enclosure.

Notification of CE marking

The following products have shown compliance through direct testing (to the

identified standards) and design analysis (forming a technical construction file) to the

European Directive for Electromagnetic Compatibility (2014/30/EU) when used as

directed by the appropriate documentation.

 This product is designed for use in industrial applications

- Type: Graphic Operation Terminal

- Models: GOT series

For more details please contact your local Mitsubishi Electric sales site.

For details of CE marking, refer to the following.

GOT2000 series User's Manual

Notes for compliance to EMC regulation

1) General notes on the use of communication cables

Any device which utilizes a data communication function is susceptible to the

wider effects of local EMC noise. Therefore, when installing any communication

cables care should always be taken with the routing and location of those cables.

The GOT units identified on the previous chapter are compliant with the EMC

requirement when the following communication cables are used.

2) General notes on Power supply

The GT2105-QTBDS and GT2105-QMBDS unit

requires an additional ferrite filter to be attached to

the 24V DC power supply cables. The filter should

be attached in a similar manner as shown in the

figure opposite, i.e. the power cables are wrapped

around the filter. However, as with all EMC

situations the more correctly applied precautions

the better the systems Electro-magnetic

Compatibility. The ferrite recommended is a TDK

ZCAT3035-1330 or similar. The ferrite should be

placed as near to the 24V DC terminals of the

GT2105-QTBDS and GT2105-QMBDS as

possible (which should be within 75mm of the

GOT terminal).

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Input power supply voltage DC24 V (+10%, -15%)

Power

consumption

Under the

maximum load

4.5 W or less 2.9 W or less

At backlight off 2.2 W or less 2.2 W or less

Inrush current 27 A or less (2ms, 25°C, at the maximum load)

Permissible instantaneous power

failure time

Within 5ms

Noise immunity Noise voltage: 1000 Vp-p, Noise width: 1 μs (by noise simulator of 30 to 100 Hz noise frequency)

Dielectric withstand voltage 500 VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Insulation resistance 10 MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Electrical wire size

For power supply: 0.75[mm

] or more, For grounding: 2[mm

] or more

Ferrules with plastic sleeve Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A

Tightening torque (terminal screws) 0.5 to 0.8 N·m

Standard Remark

EN61131-2 : 2007

Programmable

controllers -

Equipment,

requirements and

tests

EMI

Compliance with all relevant aspects of the standard.

(Radiated Emissions)

EMS

Compliance with all relevant aspects of the standard.

(ESD, RF electromagnetic field, EFTB, Surge, RF

conducted disturbances and Power frequency

magnetic field)

GOT Unit Existing Cables User Made Cables

GT2105-QTBDS

and

GT2105-QMBDS

Ex. GT01-C30R4-8P

(as shown in EX.1)

A complete list of appropriate

cables can be found in the

GOT user's manual.

3rd party cables need to be

independently tested by the

user to demonstrate EMC

compliance.

100mm

250mm

140mm

GT01-C30R4-8P

Comes equipped

Added by user

GOT units

Programmable

controller

Added by user

(9.84inch)

(3.93inch)

(5.51inch)

Ex.1

F = Ferrite core

Ex. NEC TOKIN - ESD-R-17S or similar

F F F

Up to

75mm

(2.95inch)

GT2105-QTBDS, GT2105-QMBDS

GT21 General Description

This manual describes the part names, dimensions, mounting, and specifications

of the product. Before use, read this manual and manuals of relevant products

fully to acquire proficiency in handling and operating the product. Make sure to

learn all the product information, safety information, and precautions.

And, store this manual in a safe place so that you can take it out and read it

whenever necessary. Always forward it to the end user.

Registration

Ethernet is a trademark of Xerox Corporation in the United States. The company

name and the product name to be described in this manual are the registered

trademarks or trademarks of each company.

Effective Sep. 2016

Specifications are subject to change without notice.

 2016 Mitsubishi Electric Corporation

Manual Number JY997D66601B

Date Sep. 2016

This manual confers no industrial property rights or any rights of any other

kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation

cannot be held responsible for any problems involving industrial property rights

which may occur as a result of using the contents noted in this manual.

Warranty

Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for

compensation to:

(1) Damages caused by any cause found not to be the responsibility of

Mitsubishi.

(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi

products.

(3) Special damages and secondary damages whether foreseeable or not,

compensation for accidents, and compensation for damages to products

other than Mitsubishi products.

(4) Replacement by the user, maintenance of on-site equipment, start-up test run

and other tasks.

For safe use

This product has been manufactured as a general-purpose part for general

industries, and has not been designed or manufactured to be incorporated in

a device or system used in purposes related to human life.

Before using the product for special purposes such as nuclear power, electric

power, aerospace, medicine or passenger movement vehicles, consult with

Mitsubishi Electric.

This product has been manufactured under strict quality control. However

when installing the product where major accidents or losses could occur if the

product fails, install appropriate backup or failsafe functions in the system.



HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Side

ENGLISH

CHINESE

JY997D66601B

Side

Safety Precaution

(Read these precautions before using.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and

"CAUTION".

Depending on circumstances, procedures indicated by "CAUTION" may also be

linked to serious results. In any case, it is important to follow the directions for

usage.

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury

or physical damage.

DESIGN PRECAUTIONS

 Some failures of the GOT or cable may keep the outputs on or off. Some

failures of a touch panel may cause malfunction of the input objects such as a

touch switch. An external monitoring circuit should be provided to check for

output signals which may lead to a serious accident. Not doing so can cause

an accident due to false output or malfunction.

 Do not use the GOT as the warning device that may cause a serious

accident. An independent and redundant hardware or mechanical interlock is

required to configure the device that displays and outputs serious warning.

Not doing so can cause an accident due to false output or malfunction.

 When the GOT detects its backlight failure, the GOT disables the input

operation on the touch switch(s). Thus, operators cannot operate the GOT

with touches. The GOT backlight failure can be checked with a system signal

of the GOT.

 Incorrect operation of the touch switch(s) may lead to a serious accident if the

GOT backlight is gone out.

When the GOT backlight goes out, the POWER LED blinks (blue/orange) and

the display section dims, while the input of the touch switch(s) remains active.

This may confuse an operator in thinking that the GOT is in "screensaver"

mode, who then tries to release the GOT from this mode by touching the

display section, which may cause a touch switch to operate.

 The display section of the GOT is an analog-resistive type touch panel.

Simultaneous pressing of two or more areas on the display section may

activate the switch between those areas. Do not press two or more areas

simultaneously on the display section. Doing so may cause an accident due

to incorrect output or malfunction.

 When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to shut off the power of the GOT

promptly and power on the GOT again. Not doing so can cause an accident

due to false output or malfunction.

 If a communication fault (including cable disconnection) occurs during

monitoring on the GOT, communication between the GOT and PLC CPU is

suspended and the GOT becomes inoperative. A system where the GOT is

used should be configured to perform any significant operation to the system

by using the switches of a device other than the GOT on the assumption that

a GOT communication fault will occur. Not doing so can cause an accident

due to false output or malfunction.

DESIGN PRECAUTIONS

 When the security of the GOT and relevant information need to be protected

against illegal access from an external device via the Internet, take measures at

the user's discretion.

Failure to do so may cause the configured information to be read out illegally.

DESIGN PRECAUTIONS

 Do not bundle the control and communication cables with main-circuit, power or

other wiring. Run the above cables separately from such wiring and keep them a

minimum of 100 mm apart. Not doing so noise can cause a malfunction.

 Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.

 Turn on the controllers and the network devices to be ready for communication

before they communicate with the GOT. Failure to do so can cause a

communication error on the GOT.

 When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

MOUNTING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the GOT main unit to/from the panel. Not doing so

can cause the unit to fail or malfunction.

MOUNTING PRECAUTIONS

 Use the GOT in the environment that satisfies the general specifications

described in this manual. Not doing so can cause an electric shock, fire,

malfunction or product damage or deterioration.

 When mounting the GOT to the control panel, tighten the mounting screws in the

specified torque range (0.3 N·m to 0.5 N·m) can cause the GOT to drop, short

circuit or malfunction. Overtightening can cause a drop, short circuit or

malfunction due to the damage of the screws or the GOT.

 Remove the protective film of the GOT. When the user continues using the GOT

with the protective film, the film may not be removed.

 Operate and store the GOT in environments without direct sunlight, high

temperature, dust, humidity, and vibrations.

 Do not use the GOT in an environment with oil or chemicals. Doing so may cause

failure or malfunction due to the oil or chemical entering into the GOT.

WIRING PRECAUTIONS

 Be sure to shut off all phases of the external power supply used by the system

before wiring. Failure to do so may result in an electric shock, product damage or

malfunctions.

WIRING PRECAUTIONS

 Please make sure to ground FG terminal of the GOT power supply section by

applying 100 Ω or less which is used exclusively for the GOT. Not doing so may

cause an electric shock or malfunction.

 Correctly wire the GOT power supply section after confirming the rated voltage

and terminal arrangement of the product. Not doing so can cause a fire or failure.

 Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.5 N·m to 0.8 N·m). Undertightening can cause a short circuit or

malfunction. Overtightening can cause a short circuit or malfunction due to the

damage of the screws or the GOT.

 For a terminal processing of a wire to the GOT power supply section, connect a

stranded wire or a single wire directly, or use a rod terminal with an insulation

sleeve.

 Exercise care to avoid foreign matter such as chips and wire offcuts entering the

GOT. Not doing so can cause a fire, failure or malfunction.

 Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in the

specified torque range. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction dueto the damage of the

screws or unit.

TEST OPERATION

PRECAUTIONS

 Before performing the test operations of the user creation monitor screen (such as

turning ON or OFF bit device, changing the word device current value, changing

the settings or current values of the timer or counter, and changing the buffer

memory current value), read through the manual carefully and make yourself

familiar with the operation method. During test operation, never change the data

of the devices which are used to perform significant operation for the system.

False output or malfunction can cause an accident.

Manual

The following shows manuals relevant to this product.

Detailed Manual

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the

drawing software used.

Relevant Manuals

For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM

for the drawing software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global

Website (http://www.MitsubishiElectric.co.jp/fa).

Before using the GOT

Refer to the GOT2000 Series User’s Manual (Hardware) for the connection

instructions.

For details on the GOT specifications, installing instructions, wiring, maintenance

and inspection, or checking procedure for the version and the compatible standard,

refer to the GOT2000 Series User’s Manual (Hardware).

Bundled Items

STARTUP/MAINTENANCE

PRECAUTIONS

 When power is on, do not touch the terminals. Doing so can cause an electric

shock or malfunction.

 Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases. Not doing so can cause the unit to fail or

malfunction. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

STARTUP/MAINTENANCE

PRECAUTIONS

 Do not disassemble or modify the unit. Doing so can cause a failure,

malfunction, injury or fire.

 Do not touch the conductive and electronic parts of the unit directly. Doing so

can cause a unit malfunction or failure.

 The cables connected to the unit must be run in ducts or clamped. Not doing so

can cause the unit or cable to be damaged due to the dangling, motion or

accidental pulling of the cables or can cause a malfunction due to a cable

connection fault.

 When unplugging the cable connected to the unit, do not hold and pull from the

cable portion. Doing so can cause the unit or cable to be damaged or can cause

a malfunction due to a cable connection fault.

 Do not drop the module or subject it to strong shock. A module damage may

result.

 Before touching the unit, always touch grounded metals, etc. to discharge static

electricity from human body, etc. Not doing so can cause the unit to fail or

malfunction.

 Replace battery with GT11-50BAT by Mitsubishi electric Co. only.

Use of another battery may present a risk of fire or explosion.

 Dispose of used battery promptly.

Keep away from children. Do not disassemble and do not dispose of in fire.

TOUCH PANEL

PRECAUTIONS

 For the analog-resistive film type touch panels, normally the adjustment is not

required. However, the difference between a touched position and the object

position may occur as the period of use elapses. When any difference between

a touched position and the object position occurs, execute the touch panel

calibration.

 When any difference between a touched position and the object position occurs,

other object may be activated. This may cause an unexpected operation due to

incorrect output or malfunction.

PRECAUTIONS WHEN THE

DATA STORAGE IS IN USE

 If the SD card mounted on drive A of the GOT is removed while the GOT is

accessed, processing for the GOT might be interrupted about for 20 seconds.

The GOT cannot be operated during this period. The functions that run in the

background including a screen updating, alarm, logging, scripts, and others are

also interrupted. Since this interruption makes an impact to the system

operation, it might cause failure. After inhibiting access to the SD card on the

GOT utility screen, check that the SD card access LED is off and remove the SD

card.

 If the data storage mounted on the GOT is removed while the GOT is accessed,

the data storage and files are damaged. To remove the data storage from the

GOT, check that the access to the data storage in SD card access LED, the

system signal, and others is not performed.

 Turning off the GOT while it accesses the SD card results in damage to the SD

card and files.

 When removing the SD card from the GOT, make sure to support the SD card

by hand as it may pop out. Failure to do so may cause the SD card to drop from

the GOT, resulting in a failure or break.

 Before removing the SD card from the GOT, follow the procedure for removal on

the utility screen of the GOT. After the successful completion dialog is displayed,

remove the SD card by hand carefully. Failure to do so may cause the SD card

to drop from the GOT, resulting in a failure or break.

DISPOSAL PRECAUTIONS

 When disposing of this product, treat it as industrial waste.

 When disposing of batteries, separate them from other wastes according to the

local regulations.

(Refer to the GOT2000 Series User’s Manual for details of the battery directive

in the EU member states.)

TRANSPORTATION

PRECAUTIONS

 When transporting lithium batteries, make sure to treat them based on the

transport regulations.

(Refer to the GOT2000 Series User’s Manual (Hardware) for details of the

regulated models.)

 Make sure to transport the GOT main unit and/or relevant unit(s) in the manner

they will not be exposed to the impact exceeding the impact resistance

described in the general specifications of this manual, as they are precision

devices. Failure to do so may cause the unit to fail. Check if the unit operates

correctly after transportation.

 When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden packaging

from insects, they cause malfunction when entering our products. Please take

necessary precautions to ensure that remaining materials from fumigant do not

enter our products, or treat packaging with methods other than fumigation (heat

method). Additionally, disinfect and protect wood from insects before packing

products.

Manual name

Manual number

(Model code)

GOT2000 Series User’s Manual (Hardware) SH-081194ENG (1D7MJ5)

GOT2000 Series User’s Manual (Utility) SH-081195ENG (1D7MJ6)

Model name Remark

GT2105-QTBDS,

GT2105-QMBDS

GOT main unit

(The maintenance supplies below are packed with the product.)

Model name Remark

Panel Mounting Bracket (with M4 × 35 screws) 4

Panel Mounting Packing 1

GT21 General Description (This manual) 1

1. GOT series User's Manual Specifications

1.1 General Specifications

*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.

*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90% at 40°C.

*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside

the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may

come off.

*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the

machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment

with the rated voltage up to 300 V is 2500 V.

*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-

conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.

1.2 Performance Specifications

*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as

the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to

individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.

*2 Flicker may occur due to vibration, shock, or display color.

*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.

Item Specifications

Operating ambient temperature

0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)

Storage ambient temperature -20 to 60C

Operating ambient humidity

10% RH to 90% RH, non-condensing

Storage ambient humidity

10% RH to 90% RH, non-condensing

Vibration resistance

Compliant with

JIS B3502 and

IEC61131-2

Frequency Acceleration Half amplitude Sweep Count

Under intermittent

vibration

5 to 8.4 Hz - 3.5 mm

10 times in each X,

Y, o r Z d i r e c t i o n

8.4 to 150 Hz

9.8m/s

Under continuous

vibration

5 to 8.4 Hz - 1.75 mm

8.4 to 150 Hz

4.9m/s

Shock resistant

Compliant with JIS B3502 and IEC61131-2 147m/s

(15G) Three times in each X, Y, or Z direction

Operating atmosphere No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)

Operating altitude

2000 m or less

Installation location Inside control panel

Overvoltage category

 or less

Pollution degree

2 or less

Cooling method Self-cooling

Grounding

Grounding with a ground resistance of 100 Ω or less by using a ground cable that has a diameter of 1.6 mm or more.

If impossible, connect the ground cable to the control panel.

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Display section

*1*2

Display device TFT color display TFT monochrome display

Screen size 5.7"

Resolution 320 × 240 dots

Display size 115(4.53) (W) × 86(3.39) (H) mm(inch)

Displayed number of characters

16-dot standard font: 20 characters × 15 lines (two-byte characters)

12-dot standard font: 26 characters × 20 lines (two-byte characters)

Display color Color (65536 colors) Monochrome (black/white) 32 shade grayscale

Brightness Adjustment 32 levels

Backlight LED (Not replaceable)

Backlight life

Approx. 65000 h (operating ambient temperature: 25°C, display intensity: 50%)

Touch panel

Type Analog resistive film

Key size Minimum 2 × 2 dots (per a key)

Simultaneous press

Simultaneous press prohibited

(only 1 point can be pressed)

Life 1 million times or more (Operating force: 0.98 N or less)

User memory capacity

User memory capacity Memory for storage (ROM): 9 MB

Life (number of write times) 100000 times

Battery GT11-50BAT lithium battery

Life Approx. 5 years (operating ambient temperature: 25°C)

Built-in interface

RS-232

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(male)

RS-422/485

1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps

Connector shape: D-sub 9-pin(female)

Terminating resistor

: OPEN/110 Ω/330 Ω (Switched with the terminating resistor setting switch)

USB (Device)

1 ch

Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B

SD card 1 channel SDHC card supported (max. 32 GB)

Buzzer output Single tone (tone length adjustable)

Productive structure

Outside the enclosure: IP67F

Inside the enclosure: IP2X

External dimensions 164(6.46) (W) × 135(5.32) (H) × 55(2.17) (D)

Panel cut dimensions 153(6.03) (W) × 121(4.77) (H)

Weight (excluding a fitting) Approx. 0.7 kg

Compatible software package GT Works3 Version1.144A or later

*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)

- Material: Polyacetal resin

- Tip radius: 0.8 mm or more

*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more

points on the touch panel simultaneously.

*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.

*7 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over

for a long time or where oil mist is filled.

1.3 Power Supply Specifications

2. Wiring of connection cable

For details of the connection cable, refer to the following manual.

 GOT2000 Series Connection Manual (Mitsubishi Products) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 1) For GT Works3

Version1

 GOT2000 Series Connection Manual (Non-Mitsubishi Products 2) For GT Works3

Version1

 GOT2000 Series Connection Manual (Microcomputers, MODBUS/Fieldbus

Products, Peripherals) For GT Works3 Version1

Certification of UL, cUL standards

 Using GOT

GOT is for use on a Flat Surface of a Type 1 Enclosure.

Notification of CE marking

The following products have shown compliance through direct testing (to the

identified standards) and design analysis (forming a technical construction file) to the

European Directive for Electromagnetic Compatibility (2014/30/EU) when used as

directed by the appropriate documentation.

 This product is designed for use in industrial applications

- Type: Graphic Operation Terminal

- Models: GOT series

For more details please contact your local Mitsubishi Electric sales site.

For details of CE marking, refer to the following.

GOT2000 series User's Manual

Notes for compliance to EMC regulation

1) General notes on the use of communication cables

Any device which utilizes a data communication function is susceptible to the

wider effects of local EMC noise. Therefore, when installing any communication

cables care should always be taken with the routing and location of those cables.

The GOT units identified on the previous chapter are compliant with the EMC

requirement when the following communication cables are used.

2) General notes on Power supply

The GT2105-QTBDS and GT2105-QMBDS unit

requires an additional ferrite filter to be attached to

the 24V DC power supply cables. The filter should

be attached in a similar manner as shown in the

figure opposite, i.e. the power cables are wrapped

around the filter. However, as with all EMC

situations the more correctly applied precautions

the better the systems Electro-magnetic

Compatibility. The ferrite recommended is a TDK

ZCAT3035-1330 or similar. The ferrite should be

placed as near to the 24V DC terminals of the

GT2105-QTBDS and GT2105-QMBDS as

possible (which should be within 75mm of the

GOT terminal).

Item

Specifications

GT2105-QTBDS GT2105-QMBDS

Input power supply voltage DC24 V (+10%, -15%)

Power

consumption

Under the

maximum load

4.5 W or less 2.9 W or less

At backlight off 2.2 W or less 2.2 W or less

Inrush current 27 A or less (2ms, 25°C, at the maximum load)

Permissible instantaneous power

failure time

Within 5ms

Noise immunity Noise voltage: 1000 Vp-p, Noise width: 1 μs (by noise simulator of 30 to 100 Hz noise frequency)

Dielectric withstand voltage 500 VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Insulation resistance 10 MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Electrical wire size

For power supply: 0.75[mm

] or more, For grounding: 2[mm

] or more

Ferrules with plastic sleeve Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A

Tightening torque (terminal screws) 0.5 to 0.8 N·m

Standard Remark

EN61131-2 : 2007

Programmable

controllers -

Equipment,

requirements and

tests

EMI

Compliance with all relevant aspects of the standard.

(Radiated Emissions)

EMS

Compliance with all relevant aspects of the standard.

(ESD, RF electromagnetic field, EFTB, Surge, RF

conducted disturbances and Power frequency

magnetic field)

GOT Unit Existing Cables User Made Cables

GT2105-QTBDS

and

GT2105-QMBDS

Ex. GT01-C30R4-8P

(as shown in EX.1)

A complete list of appropriate

cables can be found in the

GOT user's manual.

3rd party cables need to be

independently tested by the

user to demonstrate EMC

compliance.

100mm

250mm

140mm

GT01-C30R4-8P

Comes equipped

Added by user

GOT units

Programmable

controller

Added by user

(9.84inch)

(3.93inch)

(5.51inch)

Ex.1

F = Ferrite core

Ex. NEC TOKIN - ESD-R-17S or similar

F F F

Up to

75mm

(2.95inch)

GT2105-QTBDS, GT2105-QMBDS

GT21 General Description

This manual describes the part names, dimensions, mounting, and specifications

of the product. Before use, read this manual and manuals of relevant products

fully to acquire proficiency in handling and operating the product. Make sure to

learn all the product information, safety information, and precautions.

And, store this manual in a safe place so that you can take it out and read it

whenever necessary. Always forward it to the end user.

Registration

Ethernet is a trademark of Xerox Corporation in the United States. The company

name and the product name to be described in this manual are the registered

trademarks or trademarks of each company.

Effective Sep. 2016

Specifications are subject to change without notice.

 2016 Mitsubishi Electric Corporation

Manual Number JY997D66601B

Date Sep. 2016

在本书中，并没有对工业知识产权及其它权利的执行进行保证，也没有对

执行权进行承诺。对于因使用本书中所记载的内容而引起的工业知识产权

上的各种问题，本公司将不负任何责任。

关于质保

机会损失和间接损失不在质保责任范围内

无论是否在免费质保期内，凡以下事由三菱电机将不承担责任。

(1)任何非三菱电机责任原因而导致的损失。

(2)因三菱电机产品故障而引起的用户机会损失、利润损失。

(3)无论三菱电机能否预测，由特殊原因而导致的损失和间接损失

、事故赔偿、

以及三菱电机产品以外的损伤。

(4)对于用户更换设备、现场机械设备的再调试、运行测试及其它作业等的补

偿。

本产品是以一般工业为对象,作为通用产品所制造的产品,不可以用于关系

到人身安全的状况下所使用的设备或者系统为目的而设计、制造的产品。

在计划将本产品应用于原子能、电力、航空航天、医疗、载人运载工具的

设备或者系统等的特殊用途时，在对此进行研究商讨之际，请照会本公司

的营业窗口。

虽然本产品是在严格的质量管理体制下进行制造的，但是在计划将本产品

应用于由于本产品的故障有可能导致重大事故或者损失的设备上时，请在

系统上设置备用及失效安全系统。



安全使用注意事项

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Side

ENGLISH

CHINESE

JY997D66601B

Side

安全注意事项　（使用前请务必仔细阅读）

在使用本产品时，请务必熟读本手册以及本手册中介绍的相关手册。同时请务必充

分注意安全事宜，正确使用。

本手册中所述注意事项仅为本产品直接相关内容。

在本手册中，用“警告”和“注意”对●安全注意事项●进行等级区分。

此外，即使是的事项，因具体情况不同，也可能引发重大事故。

由于记载的都是重要的内容，所以请务必遵守。

错误操作可能引起危险情况发生，造成人员重伤或死亡。

错误操作可能引起危险情况发生，造成人员中等程度的伤

害、轻伤或物品损坏。

设计注意事项

 GOT、电缆的故障，可能会导致输出保持为ON的状态或保持为OFF的状态。触摸

面板的故障，可能会导致触摸开关等输入对象发生误动作。对于有可能引起重

大事故的输出信号，应设置外部监控电路。误输出或误动作可能导致事故发

生。

 请不要将GOT作为报警装置使用，这样有可能导致重大事故。显示重要的报警

或者输出报警的装置，请使用独立并具有冗余性的硬件或者机械互锁的构成。

误输出、误动作有可能导致事故发生。

 GOT检测出背光灯故障时，GOT将触摸开关的输入变为无效，操作人员将无法对

GOT进行触摸操作。GOT检测出背光灯故障时，可通过GOT的系统信号进行确

认。

 GOT的背光灯熄灭时，触摸开关的误操作可能会引起事故。

GOT的背光灯一旦熄灭，电源LED会闪烁（蓝/橙），显示部分全部黑屏，虽然看

不见监视画面，但触摸开关的输入仍然有效。

这时如果操作者误以为是屏幕保护状态，想解除屏幕保护而触摸了显示部分，

可能会引发触摸开关动作。

 GOT的显示屏采用的是模拟电阻膜方式。在显示屏上同时按压2点以上时，如果

按压点的中心附近有开关，该开关将可能动作。请勿在显示屏上同时按压2点

以上。同时按压2点以上有可能因误输出、误动作而导致事故发生。

 更改由GOT执行监控的连接设备（PLC等）的程序或参数等时，请快速切断GOT

电源后重新启动。误输出或误动作有可能导致事故发生。

 GOT在执行监控时，如果发生通讯故障（包括电缆脱落），GOT与可编程控制器

CPU的通讯将被中断，GOT无法动作。在构建使用了GOT的系统时，考虑到可能

会发生GOT通讯故障时，对系统进行重大动作的开关操作请设定通过GOT以外

的装置进行。否则可能会因为误输出、误动作而导致事故发生。

 针对经由互联网的外部机器的非法访问，需要对GOT及相关信息的安全给予保

护时，请制定针对不同用户的对策。

否则，设置信息可能会被非法读取。

设计注意事项

 请勿将控制线及通讯电缆与主电路及动力线等捆扎在一起或相互靠得太近。应相

距100mm以上距离。因为噪声可能导致误动作。

 请勿用钢笔及螺丝刀等尖物按压GOT的显示屏。有可能导致破损及故障发生。

 在与GOT连接前，请接通连接

设备以及网络设备的电源，使其处于可通讯状态。连接

设备以及通讯线路为不可通讯状态时，GOT可能会发生通讯报警。



GOT受到振动和撞击时，或GOT上显示特定的颜色时，GOT的画面有时会出现闪烁现象。

安装注意事项

 在将GOT本体安装到控制柜上或从控制柜上拆卸时，必须将系统中正在使用的所有

外部供应电源全部断开之后再进行操作。如未全部断开，可能导致产品故障或误动

作现象。

安装注意事项

 请在符合本说明书中所规定的一般规格环境下使用GOT。在不符合说明书中规定的

一般规格环境下使用GOT，可能会引起触电、火灾、误动作、产品损坏或使产品性能

变差现象。

 将GOT安装到控制柜上时，在规定的扭矩范围内（0.3N·m～0.5N·m）拧紧安装螺

栓。如果螺栓拧得过松，有可能导致脱落、短路、误动作。如果螺栓拧得过紧，有可

能导致螺栓及产品损坏而导致脱落、短路、误动作。

 使用时请将保护膜揭下。如果不揭下就使用，日后可能无法将其揭下。

 请勿在阳光直射的场所、高温、粉尘、湿气或振动大的场所使用以及保管本产品。

 不要将GOT在含油、药品的环境下使用。如果有油、药品浸入设备，会导致故障、误

动作。

配线注意事项

 在进行接线作业时，必须将系统中正在使用的所有外部供应电源全部断开之后再

进行操作。如果未全部断开，可能会引起触电、产品损坏、误动作。

配线注意事项

 必须将GOT电源部分的FG端子与GOT的专用接地线连接。否则，可能引起触电、误动

作。

 GOT的电源线路，应在确认了产品的额定电压及端子排列之后进行正确安装。连接

了与额定电压不匹配的电源、或者错误接线，可能导致火灾、故障。

 应在规定的扭矩范围内(0.5N·m～0.8N·m)紧固GOT电源部分的端子螺栓。如果端

子螺栓拧得过松，有可能导致短路、误动作。如果端子螺栓拧得过紧，有可能导致

螺栓及模块的损坏而引起短路、误动作。

 GOT电源部分的电线的终端处理，请直接使用绞线或单线，或使用带绝缘套管的棒

状端子。

 应注意防止切屑及线头等杂物掉入产品内。否则可能导致火灾、故障、误动作。

 通讯电缆安装在GOT的接口或与GOT连接的产品的连接器上，应在规定的扭矩范围

内拧紧安装螺栓和端子螺栓。如果安装螺栓和端子螺栓拧得过松，有可能导致短

路、误动作。如果安装螺栓和端子螺栓拧得过紧，有可能导致螺栓及模块的损坏而

引起短路、误动作。

测试操作注意事项

 应在熟读用户操作手册，充分理解操作方法后，进行用户创建的监控画面的测试操

作（位软元件的ON/OFF、字软元件的当前值更改、定时器、计数器的设置值·当前

值更改、缓冲存储器的当前值更改）。此外，对于那些对系统有重大影响的软元件

请勿通过测试操作更改其数据。否则可能导致误输出、误动作。

启动/维护注意事项

 通电时请勿触摸端子。可能引起触电。

 清洁或者紧固端子螺栓时，必须从外部将电源全部断开之后再进行操作。如果没有

全部断开，可能导致设备故障或者误动作。如果螺栓拧得过松，有可能导致短路、

误动作。如果螺栓拧得过紧，有可能由于螺栓或模块损坏引起短路、误动作。

CE标记通知

通过直接测试（已认证标准）和设计分析（形成工程技术文件）证实，下述产品在相应

文件指导下使用时可对应电磁兼容性的欧洲指令(2004/108/EC)。

 本产品设计符合工业应用

- 类型:图形操作终端

- 型号:GOT2000系列

关于更多详细内容，请向当地三菱电机销售商垂询。

关于CE标记详细内容，请参照以下内容。

→GOT2000系列主机使用说明书

关于操作手册

本产品相关的手册如下所示。

详细手册

详细的手册内容请参阅存储于所使用绘图软件的DVD-ROM或CD-ROM中的PDF手册。

Mitsubishi Electric GT21 (GT2105-QTBDS, GT2105-QMBDS) 取扱説明書

ブランド: Mitsubishi Electric

モデル: GT21 (GT2105-QTBDS, GT2105-QMBDS)

タイプ: 取扱説明書

PDFをダウンロードします

報告

他の言語で

English: Mitsubishi Electric GT21 (GT2105-QTBDS, GT2105-QMBDS) Owner's manual

Mitsubishi Electric GT21 (GT2105-QTBDS, GT2105-QMBDS) 取扱説明書

Mitsubishi Electric GT21 (GT2105-QTBDS, GT2105-QMBDS) 取扱説明書

他の言語で

関連論文

その他のドキュメント