V1.0
2017.02
Product Information
产品信息
1345LS Propeller Mounting Plate Kit
1345LS
快拆桨底座套件
INSPIRE 1
2
EN
Disclaimer and Warning
Congratulations on purchasing your new DJI™ product. The information in this
document affects your safety and your legal rights and responsibilities. Read
this entire document carefully to ensure proper conguration before use. Failure
to read and follow instructions and warnings in this document may result in
serious injury to yourself or others, damage to your DJI product, or damage to
other objects in the vicinity. This document and all other collateral documents
are subject to change at the sole discretion of DJI.
By using this product, you hereby signify that you have read this disclaimer and
warning carefully and that you understand and agree to abide by the terms
and conditions herein. You agree that you are solely responsible for your own
conduct while using this product, and for any consequences thereof.
You agree to use this product only for purposes that are proper and in
accordance with all applicable laws, rules, and regulations, and all terms,
precautions, practices, policies and guidelines DJI has made and may make
available.
DJI accepts no liability for damage, injury or any legal responsibility incurred
directly or indirectly from the use of this product. The user shall observe
safe and lawful practices including, but not limited to, those set forth in this
document.
Notwithstanding above, your statutory rights under applicable national
legislation are not affected by this disclaimer.
DJI is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”)
and its afliated companies. Names of products, brands, etc., appearing in this
document are trademarks or registered trademarks of their respective owner
companies. This product and document are copyrighted by DJI with all rights
reserved. No part of this product or document shall be reproduced in any form
without prior written consent of or authorization from DJI.
Introduction
INSPIRE™1 1345LS propeller mounting plate kit to mount the 1345 LS Quick-
Release Propellers onto the motors.
Installation
Tools Required: 2mm Hex Key/ Hex Screwdriver and LOCITITE 243 Adhesive
3
EN
Propeller adapters, retaining rings and propeller mounting plates
marked with CW should be mounted on motors marked CW, and those
marked with CCW should be mounted on motors marked CCW.
The red spring pad must be mounted on CW motors, and the silver
one on CCW motors. DO NOT mix them.
Put the screws and other parts in the correct places during installation
and removal.
Apply LOCTITE 243 adhesive for secure installation.
Using mismatched screwdrivers will lead to screws with stripped
heads that won't be able to tighten.
1. Remove the screws securing the original propeller mounting plate on the
motors, and then remove the original propeller mounting plate and the spring
pad.
Propeller mounting plate
Spring pad
2. Insert the included screws and tighten to secure the propeller adapter on the
motor. To better secure the propeller adapter, apply LOCTITE 243 adhesive
onto the screws.
Propeller adapter
4
EN
3. Secure the spring pad, retaining ring and 1345LS propeller mounting plate
on the propeller adapter in sequence, and apply LOCTITE 243 adhesive
onto the screws.
Propeller mounting plate
Retaining ring
Spring pad
4. Ensure to stick the included foam on the propellers as shown before
mounting them onto the motors.
Foam
5
CH
免责声明和警告
感谢您购买 DJI™ 产品。本文所提及的内容关系到您的安全以及合法权益与责
任。使用本产品之前，请仔细阅读本文以确保已对产品进行正确的设置。不遵
循和不按照本文的说明与警告来操作可能会给您和周围的人带来伤害，损坏本
产品或其它周围的物品。本文档及本产品所有相关的文档最终解释权归大疆 ™
创新（DJI）所有。如有更新，恕不另行通知。请访问 www.dji.com 官方网站
以获取最新的产品信息。
一旦使用本产品，即视为您已经仔细阅读本免责声明与警告，理解、认可和接
受本声明全部条款和内容。您承诺对使用本产品以及可能带来的后果负全部责
任。您承诺仅出于正当目的使用本产品，并且同意本条款以及大疆创新（DJI）
制定的任何相关条例、政策和指引。大疆创新（DJI）对于直接或间接使用本产
品而造成的损坏、伤害以及任何法律责任不予负责。用户应遵循包括但不限于
本文提及的所有安全指引。
即使存在上述规定，消费者权益依然受当地法律法规所保障，并不受本免责声
明影响。
DJI 是深圳市大疆创新科技有限公司及其关联公司的商标。本文出现的产品名
称、品牌等，均为其所属公司的商标或注册商标。本产品及手册为大疆创新版
权所有。未经许可，不得以任何形式复制翻印。
简 介
INSPIRE™ 1 1345LS 快拆桨底座套件用于将 1345LS 快拆桨固定于电机上。
安 装
自备工具：2mm 内六角扳手 / 内六角螺丝刀，LOCTITE243 胶水
桨叶转接座、挡桨圈及桨叶基座上带 CW 标志的对应 CW 电机，带
CCW 标志的对应 CCW 电机。
红色弹片对应 CW 电机，银色弹片对应 CCW 电机，切勿混用。
拆装过程中请注意保管零件，以免丢失。
请务必于螺丝螺纹处涂抹 LOCTITE243 胶水，以固定牢固。
如使用不配套的螺丝刀或螺丝刀本身有较大磨损，将会导致咬合量过
小，可能产生滑丝现象。
6
CH
1. 如图所示，松开电机上方螺丝，并将原桨叶基座和弹片取下。
桨叶基座
弹片
2. 将桨叶转接座用包装内的螺丝固定于电机上，并于螺丝螺纹处涂抹
LOCTITE243 胶水以完全固定。
桨叶转接座
3. 用包装内的螺丝分别将弹片、桨档圈、桨叶基座固定于桨叶转接座上，并
于螺丝螺纹处涂抹 LOCTITE243 胶水以完全固定。
桨叶基座
桨档圈
弹片
7
4. 安装螺旋桨前，务必将包装内所含的泡沫棉按照下图所指粘贴至螺旋桨指
定位置。
泡沫棉
If you have any questions about this
document, please contact DJI by sending
a message to
.
如果您对说明书有任何疑问或建议，请通过以下
电子邮箱联系我们：
。
www.dji.com/support
DJI Support
DJI 技术支持
INSPIRE is a trademark of DJI.
Copyright © 2017 DJI All Rights Reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
