SGS104
SGT104
SGS1045
SGS105
English (Original Instruction)
简体中文
5
12
ENGLISH (Original Instructions)
2
b
c
c
d
h
f
g
e
i
k
nt
a
1
2 3
3
ENGLISH (Original Instructions)
4
6
5
h
f
d
e
15
o
-30
o
A B
ENGLISH (Original Instructions)
4
j
7
5
ENGLISH (Original Instructions)
Intended Use
Your STANLEY small angle grinder SGS104/SGT104/
SGS1045/SGS105 has been designed for grinding metal
using the appropriate type of grinding disc. This tool is
intended for professional use.
DEFINITIONS: SAFETY GUIDELINES
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not
avoided, will result in death or serious
injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or moderate
injury.
NOTICE: Indicates a practice not related
to personal injury which, if not avoided,
may result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical Safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal Safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
4. Power Tool Use And Care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
ENGLISH (Original Instructions)
6
designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions taking into
account the working conditions and the work
tobe performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
Safety Instructions for All Operations
Safety Warnings common for Grinding
a) This power tool is intended to function
as a grinder. Read all safety warnings,
instructions, illustrations and specifications
provided with this power tool. Failure to follow
all instructions listed below may result in electric
shock, fire and/or serious injury.
b) Operations such as cutting-off , sander, wire
brush or polisher are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may
create a hazard and cause personal injury.
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannon be adequately guarded or
controlled.
f) The arbour size of wheels, flanges, backing
pads or any other accessory must properly fit
the spindle of the power tool. Accessories with
arbour holes that do not match the mounting
hardware of the power tool will run out of
balance, vibrate excessively and may cause loss
of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheel for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated
by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
j) Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a “live”
wire may make exposed metal parts of the power
tool “live” and could give the operator an electric
shock.
7
ENGLISH (Original Instructions)
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
l) Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
o) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
FURTHER SAFETY INSTRUCTIONS FOR ALL
OPERATIONS
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating
wheel, backing pad, brush or any other accessory. Pinching or
snagging causes rapid stalling of the rotating accessory which
in turn causes the uncontrolled power tool to be forced in the
direction opposite of the accessory’s rotation at the point of the
binding.
For example, if an abrasive wheel is snagged or pinched by the
workpiece, the edge of the wheel that is entering into the pinch
point can dig into the surface of the material causing the wheel
to climb out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of the wheel’s
movement at the point of pinching. Abrasive wheels may also
break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking proper
precautions as given below:
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start
up. The operator can control torque reaction or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction
opposite to the wheel’s movement at the point
of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp edges
or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Safety Warnings Specific for Grinding
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels
for which the power tool was not designed cannot be
adequately guarded and are unsafe.
b) The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator. The guard helps
to protect operator from broken wheel fragments and
accidental contact with wheel and sparks that could ignite
clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off wheels
are intended for peripheral grinding, side forces applied to
these wheels may cause them to shatter.
d) Always use undamaged wheel flanges
that are of correct size and shape for your
selected wheel. Proper wheel flanges support the
wheel thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from grinding
wheel flanges.
e) Do not use worn down wheels from larger
power tools. Wheel intended for larger power tool is
not suitable for the higher speed of a smaller tool and
may burst.
RESIDUAL RISKS
In spite of the application of the relevant safety regulations and
the implementation of safety devices, certain residual risks
cannot be avoided. These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot during
operation.
– Risk of personal injury due to prolonged use.
ENGLISH (Original Instructions)
8
– Risk of dust from hazardous substances.
Tool Symbols
The following symbols are printed on the tool:
Read the instruction manual before use.
Please wear hearing protectors.
Please wear eye protection equipment.
POSITION OF DATE BARCODE (FIG. 1)
The date barcode (n), including the year of manufacturing, is
printed on the tool housing.
E.g.:
2017 XX JN
Year of manufacturin
PACKAGE CONTENT
This product package includes:
1 Angle grinder
1 Guard
1 Flange set
1 Spanner
1 Handle (only apply for SGS104, SGS1045, SGS105)
1 Instruction manual
• Check the tool, parts, and accessories to see if they are
damaged during transportation.
• Take a few moments to read and understand this manual
before using the tool.
Description (Fig. 1)
Warning: Never modify the power tool
or any part of the tool, otherwise it may
cause damage to the tool or result in
personal injury.
a. ON/OFF switch
b. Spindle lock
c. Guard
PURPOSE OF DESIGN
This angle grinder is designed especially for grinding.
Do not use sandpaper discs and grinding wheels other than
those with depressed center.
Do not use the tool in wet conditions or environments in the
presence of flammable liquids or gases.
This heavy-duty angle grinder is a professional power tool.
Do not allow children to come in contact with this tool.
Inexperienced operators are required to use this tool under
supervision.
ELECTRICAL EQUIPMENT SAFETY
Only one voltage is applicable to this tool. Be sure to check that
the power suuply corresponds to the voltage on the rating plate.
Your Stanley tool is equipped with double
insulation, hence, it does not require to be
earthed.
When the power cord is damaged, have it sent to a
Stanley service center for replacement to specially
prepared cables.
USING EXTENSION CORDS
If an extension cord is required, please select a 3-phase
extension cord that has been inspected and matches the
input power (see Technical Data) of this tool. The minimum
conductor size is 1.5mm2, maximum length is 30 meters.
When using a cable reel, be sure to pull out all the cables.
ASSEMBLY AND ADJUSTMENT
WARNING: To minimize the danger of serious
personal injury, please switch off the tool
power and disconnect all plugs before adjusting
or removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched
off.
Attaching and Removing the Wheel Guard (Fig. 2)
WARNING: To minimize the danger of
serious personal injury, please switch off the tool
power and disconnect all plugs before adjusting
or removing/installing any accessory. Before
reassembling the tool, press and release the trigger
switch to make sure the tool is already switched
off.
Attaching the Guard
1. Place the angle grinder on a work bench, groove facing
up.
2. Bring the flange of the guard (c) collar over the groove (i)
of the gear housing.
3. Turn the guard (c) counterclockwise by 150 degrees.
4. Make sure that the screws (k) are tightened.
Removing the Guard
1. Loosen the screws (k) on the guard collar.
2. Pull up the guard (c).
9
ENGLISH (Original Instructions)
Warning: Do not operate the tool when the
safety guard is not in place.
Note: Refer to the grinding accessories chart at the end of
this section for accessories that can be used together with this
angle grinder.
Attaching and Removing Grinding Wheels (Fig.
3, 4)
Warning: Do not use damaged grinding
wheels.
1. Place the tool on a work bench, groove facing up.
2. Attach the inner flange (d) correctly on the output shaft (e)
(Fig. 3).
3. Place the grinding wheel (f) on the inner flange (d). When
attaching a grinding wheel with a raised center, make sure
that the raised center (g) faces the inner flange (d).
4. Tighten the outer flange (h) until the output shaft (e) (Fig.
4). When attaching the grinding wheel, the ring on top of
the outer flange (h) must face the wheel.
5. Press the spindle lock (b) and prevent the spindle (e) from
rotating until it locks in place.
6. Use the pin spanner to tighten the outer flange (h).
Preparation Before Use
• Attach the safety guard and appropriate abrasive or
grinding wheels. Do not use abrasive or grinding wheels
that are overly worn.
• Make sure that the inner and outer flanges are attached
correctly.
• Make sure that the abrasive or grinding wheels are rotating
in the direction of the arrows on the accessories and tool.
Operation (Fig. 5)
Instructions
Warning: Always observe the safety
instructions and applicable regulations.
Warning: To minimize the danger of
serious personal injury, please switch off
the tool power and disconnect all plugs
before adjusting or removing/installing any
accessory. Before reassembling the tool,
press and release the trigger switch to
make sure the tool is already switched off.
Warning:
• Make sure all materials to be grinded are
secured in position.
• Apply slight pressure to the tool. Do not
apply side pressure to the abrasive disc.
• Avoid overloading. If the tool becomes
hot, let it spin for a few minutes with no
load.
1. Be sure to hold the tool tightly with both hands (one hand
on housing, the other on side handle). Start the tool and
bring the grinding wheel on the workpiece.
2. Keep the edge of the wheel tilted at angle from 15 to 30
degrees against the surface of the workpiece.
3. When using a new grinding wheel, do not operate the
wheel in the B direction, otherwise, it will cut into the
workpiece. When the edge of wheel has been rounded
off, you are free to operate the grinder in either the A or B
direction.
Starting and Stopping (Fig. 1)
Warning: Before using the tool, check
whether the handle is tightened securely.
Check whether the ON/OFF switch is
working normally.
Before plugging in the tool to the power supply, check whether
the switch is in the OFF (o) position when pressing the rear
end of the switch.
Slider switch (SGS104, SGS1045, SGS105)
Before plugging in the tool to the power supply, check whether
the switch is in the OFF (a) position when pressing the rear
end of the switch.
To start the tool, press the rear end of the switch and slide it
forward. Then press the front end of the switch to lock it. Press
the rear end of the switch to stop the tool.
Toggle swithch (SGT104)
To run the tool, press the switch (j) in before moving it
completely forward.
To stop the tool, move the switch (j) back the opposite way.
to stop the tool in continuous operation, press on back part of
the switch.
Warning: Do not switch the tool on or off
while under load conditions.
Warning: Do not switch the tool on or off
while under load conditions.
CAUTION: Hold the body of the tool firmly
to maintain control of the tool at start
up and during use and until the wheel or
accessory stops rotating. Make sure the
wheel has come to a complete stop be
fore laying the tool down.
NOTE: To reduce unexpected tool movement, do not
switch the tool on or off while under load conditions.
Allow the grinder to run up to full speed before
touching the work surface. Lift the tool from the
ENGLISH (Original Instructions)
10
surface before turning the tool off. Allow the tool to
stop rotating before putting it down.
SLIDER SWITCH (SGS104, SGS1045, SGS105)
Warning: Before connecting the tool to a
power supply, be sure the slider switch
is in the off position by pressing the
rear part of the switch and releasing.
Ensure the slider switch is in the off
position as described above after any
interruption in power supply to the tool,
such as the activation of a ground fault
interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure.
If the slider switch is locked on when the
power is connected, the tool will start
unexpectedly.
To start the tool, slide the slider switch (a) toward the front of
the tool.
To stop the tool, release the slider switch.For continuous
operation, slide the switch toward the front of the tool and
press the forward part of the switch inward.
To stop the tool while operating in continuous mode, press the
rear part of the slider switch and release.
TOGGLE SWITCH (SGT104)
Warning: Before connecting the tool to a
power supply, be sure the toggle switch
is in the off (0) position by pressing the
rear part of the switch and releasing.
Ensure the toggle switch is in the off
position as described above after any
interruption in power supply to the tool,
such as the activation of a ground fault
interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure.
If the toggle switch is locked on when
the power is connected, the tool will start
unexpectedly.
To start the tool, move the switch (j) completely forward to "1"
position.To stop the tool, move the switch (j) back the opposite
"0" position.To run the tool in continuous operation, keep
the switch (j) on "1" position. To stop the tool in continuous
operation, move the switch (j) back the opposite "0" position.
Proper Hand Position (Fig. 6)
Warning: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
Warning: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle (figure
1), with the other hand on the body of the tool, as shown in figure
6.
Spindle lock (Fig. 1)
The spindle lock (b) prevents the output shaft from rotating
when attaching or removing the grinding wheel. Only use the
spindle lock when the tool is switched off, power is unplugged,
and wheel stops completely.
NOTE: To minimize tool damages, don't
use the spindle lock when the tool is
operating. Otherwise, it may damage the
tool. The attached accessories may come
off and cause injury.
If using the spindle lock, press the spindle lock button and rotate
the output shaft until it stops.
Application on Metals
When applying the tool on metals, make sure that a residual-
current device (RCD) is inserted to prevent danger from metal
chips.
If the RCD causes power disconnection, have the tool sent to an
authorized Stanley dealer for repair.
Warning: Under extreme working
conditions, conductive dust and grit may
accumulate on the housing interior when
handling metal workpieces. This could
create an electric shock hazard as it
weakens the protective insulation in the
grinder.
To avoid accumulation of metal chips in the interior of the
grinder, we recommend cleaning the ventilation ducts daily.
Refer to Maintenance.
Using Grinding Wheels
Warning: Metal powder accumulates.
Excessive use of the grinding wheel on
metals may increase the risk of electric
shock. To reduce the risk, insert the RCD
before use and clean the ventilation ducts
daily. Follow the maintenance instructions
below to blow dry compressed air into the
ventilation ducts.
MAINTENANCE
Stanley power tools have been designed to operate over a
long period of time with minimal maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Warning: To minimize the danger of
serious personal injury, please switch off
the tool power and disconnect all plugs
before adjusting or removing/installing any
11
ENGLISH (Original Instructions)
accessory. Before reassembling the tool,
press and release the trigger switch to
make sure the tool is already switched off.
Lubrication
This power tool does not require separate lubrication.
Cleaning
Warning: Once visible dust accumulates on
the ventilation ducts and the surrounding,
immediately use dry air to blow away dust
and grit out of the interior of the housing.
You need to wear approved eye and facial
protective gear when performing this
process.
Warning: Never use solvents or harsh
chemicals to clean non-metal parts of the
tool. These chemicals may weaken the
material of the parts. Use only mild soap
and damp cloth to clean the tool. Never
let any liquid get inside the tool; never
immerse any part of the tool into liquid.
Accessories
Warning: Excluding accessories provided
by Stanley, all other accessories have
not been tested for product compatibility.
Using such accessories together with
this tool may cause safety hazards. To
minimize the risk of personal injury,
we recommend you to use only Stanley
accessories with this product.
Please inquire at your dealer for more information regarding
suitable accessories.
Protecting The Environment
Sorting and Recycling. This product is not
to be disposed of with normal household
waste.
In the event that you need to replace your Stanley product or if
it is of no further use to you, please do not dispose of it together
with household waste. Please sort it out for separate recycling.
Sorting out and recycling used products
and packaging ensure usable materials
are recycled and reused. Reusing
reusable materials helps to prevent
environmental pollution and reduce the
demand for raw materials.
Regulations may stipulate your local city council and new
product retailers to provide waste disposal centers or electrical
product recycling service.
Stanley provides collection and recycling of end-of-life
products. To enjoy this service, please have the product sent
back to any authorized dealer for recycling.
Remarks
• Stanley's policy is one of continuous improvement to our
products and as such, we reserve the right to modify
product specifications without prior notice.
• Standard equipment and accessories may vary by
country.
• Product specifications may differ by country.
• Complete product range may not be available in all
countries. Contact your local Stanley dealers for range
availability
TECHNICAL DAT
SGS104 SGT104 SGS1045 SGS105
Voltage V 220 220 220 220
Frequency Hz 50 50 50 50
Power input W 1050 1050 1050 1050
No-load speed/
rated speed
min
-
1
11000 11000 11000 11000
Wheel diameter mm 100 100 115 125
Grinding wheels
thickness
mm 6 6 6 6
Type of wheel 27 27 27 27
Spindle diameter M10 M10 M14 M14
Weight kg 1.9 1.9 2.0 2.0
12
简体中文
SGS104/SGT104/SGS1045/
SGS105
定义：安全指引
一般安全规则
/
a)
1)
2)
3)
b)
1)
2)
3)
4)
5)
c)
1)
2)
3)
4)
5)
6)
13
简体中文
7)
d)
1)
2)
3)
/
4)
5)
6)
7)
e)
a)
所有操作的使用说明
a)
/
b)
c)
d)
e)
f)
g)
1min
h)
i)
14
简体中文
j)
k)
l)
m)
n)
o)
p)
所有操作的进一步安全指示
/
a)
b)
c)
d)
e)
砂磨和切割操作的附件安全说明
a)
b)
c)
15
简体中文
1
1
1
1 (
SGS104, SGS1045, SGS105
)
1
•
•
1
a. /
b.
c.
电气安全
d)
e)
–
–
–
–
–
工具上的标记
1
(n)
2017 XX JN
包装内容
1
16
简体中文
使用延长电缆
3
1.5 30
组装和调整
/
2
/
1.
2. (c) (i)
3. (c) 150
4. (k)
1. (k)
2. (c)
34
1.
2. (d) (e) 3
3. (f) (d)
(g)
(d)
4. (h) (e) 4
(h)
5. (b) (e)
6. (h)
•
•
•
5
/
•
•
•
17
简体中文
(
SGS104, SGS1045, SGS105
)
(a)
(
SGT104
)
(0)
(j) 1
(j) 0
1
0
6
1.
2. 15
30
3. B
A B
1
o
SGS104, SGS1045, SGS105
a
SGS104
j
j
18
简体中文
6
6
1
(b)
(RCD)
RCD
RCD
维护
/
19
简体中文
•
•
•
•
技术参数
SGS104 SGT104 SGS1045 SGS105
V 220 220 220 220
Hz 50 50 50 50
W 1050 1050 1050 1050
/
min
-
1
11000 11000 11000 11000
mm 100 100 115 125
mm 6 6 6 6
27 27 27 27
M10 M10 M14 M14
kg 1.9 1.9 2.0 2.0
: ( )
: ( )
88 676A
:
N538614
07/2017
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
