1
DS-225 series
2
Contents
1. Warning & Statements。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
2. Voltage。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
3. Device Application。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
4. Technical Specifications。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
5. Structure Overview。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
6. Installation & Sandpaper Replacement。。。。。。。。。。。。。。。
7. Installation & viscid disc Replacement。。。。。。。。。。。。。。。
8. Connection Set for Dust Outlet。。。。。。。。。。。。。。。。。。。。。。
9. Switch& Speed Governor Operation。。。。。。。。。。。。。。。。。
10. The operation of the edge angle 。 。 。。。。。。。
11. Folding installation and disassembly。。。。。。。
3
12. Suction adjustment。。。。。。。。。。。。。。。。
13. LED light (Optional)。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
14. Application Diagram。。。。。。。。。。。。。。。。。。。。。。。。。。。
15. Cleaning。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
16. Replacement of carbon brush。。。。。。。。。。。。。。。。。。。。
1) Work area
a) Keep work area clean and well lit. Cluttered
and dark areas may result in an accident.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control of the powered tool and may
cause bodily injury.
4
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce the risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock and may make
the tool inoperative.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tools in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3) Personal safety
5
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
bodily injury.
b) Use safety equipment. Always wear eye
protection. Safety equipment such as dust mask,
non-skid safety shoes, hard hat, protective
eyewear, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c) Avoid accidental starting. Ensure the switch is
in the off position before plugging in. Carrying
power tools with your finger on the switch or
plugging in power tools that have the switch on
will result in an accident and cause bodily injury.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in bodily injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
6
ensure these are connected and properly used.
Use of these devices can reduce dust related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will deliver better results and safer at
the rate for which it was designed for.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
7
are less likely to bind and are easier to control;
g) Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations other than it was
intended for could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturer’s recommendations,
when selecting sanding paper. Larger sanding paper
extending beyond the sanding pad presents a
laceration hazard and may cause snagging, tearing of
the disc or kickback
1． Voltage
Before connecting electric tool to the socket, make
sure the supply voltage is in accordance with rated voltage.
If the former is greater than latter and the device is powered
on by mistake, it may result in damage of devices and in
bodily injury. As for indefinite supply voltage of socket,
never try to plug it for use. Besides, the damage to the
8
devices, may also occur if the supply voltage falls below
rated voltage.
2. Device Application
As one of our products, the device belongs to the
hand-held electric tools.
The device mainly caters for lime surface, including
the interior wall, ceiling, exterior wall, corridor, etc.
Remove the painting lime mud from the wall, and make the
surface even or smooth. It may promote the wall grinding
efficiency and quality by workers.
With various conditions taken into consideration in the
design, the device may run at high or low speed. In addition,
you may adjust the connection structure at high and low
locations respectively, to optimize the grinding efficiency
and realize user-friendly and compact design.
3. Technical Specifications
Model DS-225A DS225AVS DS225-2 DS-2252VS
Rated Voltage 110（V~）
Frequency 60（Hz）
Rated Power 750（W）
No-load Speed 800-1750(R/min)
Sandpaper Dimensions Ф225（mm）
Spindle Thread M14
Safety Standard II /
Net/Gross Weight 13.8（Lbs）
Model DS-225A DS225AVS DS225-2 DS-2252VS
Rated Voltage 110（V~）
9
Frequency 60（Hz）
Rated Power 750（W）
No-load Speed 800-1750 (R/min)
Sandpaper Dimensions Ф225（mm）
Spindle Thread M14
Safety Standard II /
Net/Gross Weight 13.8（Lbs）
4．Structure Overview (See following pictures)
Complete appliance
DS-225 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.5FT
10
DS-225AVS 28.7x10.8x17.5（in/2pc） Length 4.1FT/5.5FT
11
DS-225-2 44x11x7.4（in/1pc）Length 4.1FT/6.2FT
12
DS-2252VS 44x11x7.4 ( in/1pc ) Length 4.1FT/6.2FT
13
DS-225-2 Plastic viscid disc component
2. Sandpaper
4. Speed governor 3.Switch
14
5. Dust Outlet 6.Vacuum dust hose
7. Handle
8. Lengthening bar
15
9. Locking nut
1 Plastic viscid disc component
2 Sandpaper
3 Switch
4 Speed governor
5 Dust Outlet
6 Vacuum dust hose
7 Handle
8 Lengthening bar
9 Locking nut
Standard Accessories
Drywall: 1pc Instruction manual: 1pc
Sandpaper: 6pcs Allen Wrench: 1pcs
Carbon Brush: 2pcs Telescopic Dust hose: 4 m/1pcs
Dust bag: with self-cleaning with 1
16
5. Installation & Sandpaper Replacement (See following
picture)
Note: Prior to installation or removing the sandpaper,
make sure to not only switch off the device, but also cut off
the power supply.
17
——Installation Guide
To ensure the replacement procedures, place the
device on smooth and even ground prior to installation.
Take the sandpaper from the toolbox, and attach it onto the
disk. The back of the sandpaper (Item 1) will automatically
glue with the disk/adhesive disk (Item 2), making both
connection and conduction available.
In order to promote the grinding efficiency, it is
necessary to change the sandpaper after the device has been
operational for a certain period. Firstly, switch off the
device and disconnect from the socket. Then, remove the
previous sandpaper entirely from the disk, to lay new
sandpaper neatly as well as facilitate future replacement. At
last, fix new sandpaper in position.
——Sandpaper Overview
Grinding towards the target wall and object is possible
with abrasive grains and sandpaper twisting upon
operations. The sandpaper is classified into various
categories per its dimensions. It is recommended to select
the sandpaper in accordance with actual size of the disk.
The more abrasive grains included on the sandpaper, result
in flatter and smoother surface, and can be achieved via
grinding, while the grinding efficiency will fall accordingly
and vice versa. Therefore, the sandpaper (Ф225mm) is
recommended upon actual needs.
Warning ： Prior to the sandpaper replacement or
installation please read safety precautions and installation
guides carefully.
18
6. Installation & viscid disc Replacement (See following picture)
If the viscid disc is damaged during use, a new viscid disc
can be purchased from our company for replacement. 。
——Installation Guide
Viscid disc
Remove the sandpaper, put the Allen wrench into the
hexagon hole in the center of the viscid disc and then rotate
anticlockwise to take off the damaged viscid disc. Install
the new viscid disc (see the picture).
7. Connection Set for Dust Outlet (See following
pictures)
19
a Component b Lock
b a
As the name implies, it is used for connecting the
device to Dust Outlet (accessory). The dust will come out
from the wall upon operating the grinder. The device is
connected to Dust Collector in the back via Connection Set
for Dust Outlet, making it possible for the operator to
20
reduce the amount of dust.
——Installation Guide
Plug the component b into component, make the lock in the
groove and rotate clockwise.
——Dismantling Process
Rotate the lock anticlockwise and pull out the dust hose
8. Switch & Speed Governor Operation
The switch of the machine is a two step switch. As shown in
following picture, press the switch button and push forward to
power on. Press the switch button and turn back to power off.
The Speed Governor, as shown in the following picture, may be
used to regulate the speed, to facilitate the operations of workers
and improve work quality simultaneously.
Speed Governor Switch
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/
