注册您的产品并在以下网站链接中了解详情
HR2028
www.philips.com/welcome
技术规格如有变更,恕不另行通知
© 2013 Koninklijke Philips Electronics N.V.
保留所有权利
HR2028_Safety_V1.0
3140 035 34061
EN Importantinformationleaet
ZH-CN
重要信息手册
English
1 Important
Read this Important Information leaet carefully before you use the blender and save it for
future reference.
General
Danger
• Never immerse the motor unit in water or any other liquid, nor rinse it under the tap. Use
only a moist cloth to clean the motor unit.
Warning
• Before you connect the appliance to the power, make sure that the voltage indicated on
the bottom of the appliance corresponds to the local power voltage.
• If the power cord, the plug, or other parts are damaged, do not use the appliance.
• If the power cord is damaged, you must have it replace by Philips, a service center
authorized by Philips, or similarly qualied person to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• For their safety, do not allow children to play with the appliance.
• Do not touch the blades, especially when the appliance is plugged in. The blades are very
sharp.
• Always unplug the appliance before you assemble, disassemble or make adjustments to
any of the parts.
• Never reach into the blender jar with your ngers or an object while the appliance is
running.
• Make sure the blade unit is securely fastened to the blender jar before you assemble the
blender jar onto the motor unit.
• Do not touch the cutting edges of the blender blade unit when you clean it. They are very
sharp and you could easily cut your ngers on them.
• If the blades get stuck, unplug the appliance before you remove the ingredients that block
the blades.
Caution
• To prevent failure of the appliance, make sure that no food or liquid enters the connection
point of the blender jar on the motor unit.
• Never use any accessories or parts from other manufacturers or that Philips does not
specically recommend. If you use such accessories or parts, your guarantee becomes
invalid.
• Do not exceed the maximum level indicated on the accessories.
• Never ll the blender jar with ingredients hotter than 80ºC.
• To prevent spillage, do not put more than 1liter of liquid in the blender jar, especially when
you process at a high speed. Do not put more than 750ml in the blender jar when you
process hot liquids or ingredients that tend to foam.
• If food sticks to the wall of the blender jar, switch off the appliance and unplug it. Then use
a spatula to remove the food from the wall.
• Never forget to place the sealing ring on the blade unit before you assemble the blender
jar, otherwise leakage will occur.
• Always make sure the lid is properly closed/assembled on the jar and the measuring cup is
inserted properly in the lid before you switch on the appliance.
• Do not let the appliance run for more than 2 minutes at a time. If you have not nished
processing after 2 minutes, switch off the appliance and let it cool down to room
temperature before you let it run again.
Dry mill and wet mill
Warning
• Do not use the dry mill to grind very hard ingredients such as nutmeg, Chinese rock sugar
and ice cubes.
• Do not use the wet mill to mix liquids or to crush ice cubes. Use the blender jar to
process these ingredients.
• Do not touch the cutting edges of the blade unit when you clean it. The cutting edges are
very sharp and you could easily cut your ngers on them.
Caution
• Never use the dry mill or wet mill for more than 30 seconds without interruption. Let the
dry mill or wet mill cool down for at least 1 minute between processing batches.
• Let hot ingredients cool down before you process them in the dry or wet mill (max.
temperature 80°C).
• Never forget to place the sealing ring in the blade unit before you assemble the mill
beaker, otherwise leakage occurs.
• Always process cloves, star anise and aniseed together with other ingredients. If processed
separately, these ingredients may attack the plastic materials of the mill.
• The mill beakers may become discoloured when you use them to process ingredients
such as cloves, anise and cinnamon.
• The dry mill and wet mill are not suitable for chopping raw meat. Use the blender instead.
• Do not use the dry mill or wet mill to process liquids such as fruit juice.
• Do not process dry ingredients such as coffee beans and dried beans in the wet mill.