DeWalt DCD709 ユーザーマニュアル

ブランド: DeWalt

モデル: DCD709

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

このマニュアルも適しています

DCD708

DCD709

Final page size: A5 (148mm x 210mm)

English 3

简体中文 13

繁體中文 21

한국어 29

 38

Fig. A

图

圖

그림

A

Fig. B

图

圖

그림

 B

Fig. C

图

圖

그림

 C

Fig. D

图

圖

그림

 D

Fig. E

图

圖

그림

 E

ENGLISH

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough

product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

DCD708 DCD709

Voltage

18(20 Max) 18(20 Max)

Battery type

Li-Ion Li-Ion

Power output

W 340 340

No-load speed

1st gear

2nd gear

min

-1

min

-1

0–450

0–1650

0–450

0–1650

Beats per minute

1st gear

– 0–7650

2nd gear

– 0–28050

Max. Torque (hard/soft)

Nm 65/26 65/26

Chuck capacity

mm 1.5–13 1.5–13

Maximum

drilling

capacity

Wood

Metal

Masonary

–

Weight (without battery pack)

kg 1.10 1.20

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given in

IEC60335 and may be used to compare one tool with another. It

may be used for a preliminary assessment ofexposure.



WARNING: The declared vibration emission level

represents the main applications of the tool. However if

the tool is used for different applications, with different

accessories or poorly maintained, the vibration emission

may differ. This may significantly increase the exposure

level over the total workingperiod.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job.

This may significantly reduce the exposure level over the

total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of workpatterns.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

English (original instructions)

CORDLESS COMPACT 13 mm DRILL/DRIVER/HAMMERDRILL

DCD708, DCD709

Batteries Chargers/Charge Times (Minutes)

Cat# V

Ah Weight(kg)

DCB107 DCB112 DCB115 DCB118 DCB132

DCB546 18/54 6.0/2.0 1.05 270 170 90 60 90

DCB547 18/54 9.0/3.0 1.46 420 270 140 85 140

DCB548 18/54 12.0/4.0 1.44 540 350 180 180 120

DCB181 18 1.5 0.35 70 45 22 22 22

DCB182 18 4.0 0.61 185 120 60 60 60

DCB183/B 18 2.0 0.40 90 60 30 30 30

DCB184/B 18 5.0 0.62 240 150 75 75 75

DCB185 18 1.3 0.35 60 40 22 22 22

DCB187 18 3.0 0.54 140 90 45 45 45

DCB189 18 4.0 0.54 185 120 60 60 60

ENGLISH

GENERAL POWER TOOL SAFETY WARNINGS



WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or the battery pack, if detachable, from the power

tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power

toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

ENGLISH

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130 °C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

Safety Instructions When Using Long

DrillBits

• Never operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is likely

to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Always start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contacting the

workpiece, resulting in personalinjury.

• Apply pressure only in direct line with the bit and do not

apply excessive pressure. Bits can bend causing breakage or

loss of control, resulting in personalinjury.

Additional Safety Warnings for Drill/ Driver/

Hammerdrill

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body is unstable and may lead to loss

ofcontrol.

• Accessories and tool may get hot during operation. Wear

gloves when handling them if performing heat producing

applications such as drillingmetals.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be caught in

movingparts.

• Wear safety goggles or other eye protection. Hammering

and drilling operations cause chips to fly. Flying particles can

cause permanent eye damage.

• Wear ear protectors when impact drilling. Exposure to

noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting

a “live” wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

• Do not operate this tool for long periods of time.

Vibration caused by tool action may be harmful to your

hands and arms. Use gloves to provide extra cushion and

limit exposure by taking frequent rest periods.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your DeWALT charger is double insulated in

accordance with IEC60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the DeWALT

serviceorganisation.

ENGLISH

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only DeWALT rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard 220-

240V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

1

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

2

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

ENGLISH

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

ENGLISH

that could contact them and cause a shortcircuit.

NOTE: Lithium-ion batteries should not be put in

checkedbaggage.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a DeWALT battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities, DeWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLT

Battery

The DeWALT FLEXVOLT

battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLT

battery stands alone or is in

a DeWALT 18V product, it will operate as an 18V battery. When

the FLEXVOLT

battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLT

battery, the battery is in Transport mode. Keep the cap

for shipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

Example of Use and Transport Label Marking

batteries of 36 Wh each. The Use Wh rating might indicate

108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the

labels on the charger and the battery pack may show the

following pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose to water.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other

than the designated DeWALT batteries with a

DeWALT charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36Wh).

ENGLISH

Battery Type

The DCD708/DCD709 operates on an 18 volt batterypack.

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189,

DCB546, DCB547, DCB548. Refer to Technical Data for

moreinformation.

Package Contents

The package contains:

1 Drill/driver (DCD708) or Hammerdrill (DCD709)

1 Charger

1 Belt hook (included with some models)

1 Magnetic bit holder (included with some models)

1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)

2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)

3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Visible radiation. Do not stare intolight.

Date Code Position (Fig. A)

The date code

14

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2018 XX XX

Year of Manufacture

Description (Fig. A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Battery pack

Battery pack release button

Main handle

Variable speed trigger

Forward/reverse control button

Mode selection collar

Speed selector

Worklight

Chuck sleeve

Keyless chuck

Belt hook (included with some models)

Screw

Magnetic bit holder (included with some models)

Date code

Intended Use

These drills/drivers/hammerdrills are designed for professional

drilling, percussion drilling and screwdrivingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

These drills/drivers/hammerdrills are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only DeWALT battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

1

is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack

1

with the rails inside the tool’s

handle (Fig.B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

2

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some DeWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

ENGLISH

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Belt Hook and Magnetic Bit Holder (Fig.A)

(Optional Accessories)



WARNING: To reduce the risk of serious personal

injury, DO NOT suspend tool overhead or suspend

objects from the belt hook. ONLY hang tool’s belt hook

from a workbelt.



WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

IMPORTANT: When attaching or replacing a belt hook or

magnetic bit holder, use only the screw that is provided. Be sure

to securely tighten thescrew.

A belt hook

11

and magnetic bit holder

13

can be be attached

to either side of the tool using only the screw

12

provided,

to accommodate left- or right-handed users. If the hook or

magnetic bit holder is not desired at all, it can be removed from

thetool.

To move belt hook or magnetic bit holder, remove the screw

12

that holds it in place then reassemble on the opposite side. Be

sure to securely tighten thescrew.

Installing a Bit or Accessory into a

KeylessChuck (Fig.D)



WARNING: Do not attempt to tighten drill bits (or

any other accessory) by gripping the front part of the

chuck and turning the tool on. Damage to the chuck

and personal injury may result. Always lock off trigger

switch and disconnect tool from power source when

changingacces sories.



WARNING: Always ensure the bit is secure before starting

the tool. A loose bit may eject from tool causing possible

personalinjury.

Your tool features a keyless chuck

10

with one rotating sleeve

9

for one-handed operation of the chuck. To insert a drill bit or

other accessory, follow thesesteps.

1. Turn tool off and remove batterypack.

2. Grasp the black sleeve of the chuck with one hand

and use the other hand to secure the tool. Rotate the

sleeve counterclockwise far enough to accept the

desiredaccessory.

3. Insert the accessory about 19 mm into the chuck and

tighten securely by rotating the chuck sleeve clockwise with

one hand while holding the tool with the other. Your tool is

equipped with an automatic spindle lock mechanism. This

allows you to open and close the chuck with onehand.

Be sure to tighten chuck with one hand on the chuck sleeve and

one hand holding the tool for maximumtightness.

To release the accessory, repeat steps 1 and 2above.

Speed Selection (Fig.A)

The tool features two speed settings for greaterversatility.

NOTE: Do not change speeds when the tool is running.

Always allow the tool to come to a complete stop before

changingspeed.

1. To select speed 1 (high torque setting), turn the tool off and

permit it to stop. Slide the speed selector

7

back (away

from thechuck).

2. To select speed 2 (high speed setting), turn the tool off and

permit it to stop. Slide the speed selector

7

forward (toward

thechuck).

If the tool does not change speeds, confirm that the speed

selection switch is completely engaged in the forward or

backposition.

Mode Selection (Fig. A)

The mode selection collar

6

can be used to select the correct

operating mode depending upon the plannedapplication.

To select, rotate the collar until the desired symbol aligns with

thearrow.

Symbol Mode

Drilling

1–15 Screwdriving (higher number = greater torque)

Hammerdrilling (DCD709 only)

Variable Speed Trigger and Forward/Reverse

Control Button (Fig. A, E)

The drill is turned on and off by pulling and releasing the

variable speed trigger

4

. The farther the trigger is depressed,

the higher the speed of the drill. Your tool is equipped with

a brake. The chuck will stop as soon as the trigger switch is

fullyreleased.

A forward/reverse control button

5

determines the rotational

direction of the tool and also serves as a lock-offbutton.

• To select forward rotation, release the trigger and depress

the forward/reverse control button on the right side of

thetool.

• To select reverse, depress the forward/reverse control

button on the left side of thetool.

NOTE: The centre position of the control button locks the tool

in the off position. When changing the position of the control

button, be sure the trigger isreleased.

NOTE: Continuous use in variable speed range is not

recommended. It may damage the switch and should

beavoided.

NOTE: The first time the tool is run after changing the direction

of rotation, you may hear a click on start up. This is normal and

does not indicate aproblem.

ENGLISH

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. C)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle

3

and one hand on the batterypack.

Worklight (Fig.A)

There is a worklight

8

located on the foot of the tool. The

worklight is activated when the trigger switch is depressed.

When the trigger is released, the worklight will stay illuminated

for up to 20seconds.

NOTE: The worklight is for lighting the immediate work surface

and is not intended to be used as aflashlight.

Performing an Application (Fig.A, D)



WARNING: To reduce the risk of personal injury,

ALWAYS ensure workpiece is anchored or clampedfirmly.



WARNING: Always wait until the motor has come to

a complete standstill before changing the direction

ofrotation.

Prior to performing work:

• Set the speed selector

7

. Refer to SpeedSelection.

• Install the appropriate bit or accessory into the chuck. Refer

to Installing a Bit or Accessory into a KeylessChuck.



WARNING:

• Do not use this tool to mix or pump easily combustible

or explosive fluids (benzine, alcohol,etc.).

• Do not mix or stir flammable liquids

labeledaccordingly.

Screwdriving

Your tool has a clutch with adjustable torque for driving

and removing a wide array of fastener shapes and sizes. The

numbers on the mode selection collar

6

are used to set a

torque range for screwdriving. The higher the number on the

collar, the higher the torque and the larger the fastener which

can bedriven.

1. Turn the mode selection collar

6

to the desiredposition.

Refer to Mode Selection.

2. Pull the trigger switch applying pressure in a straight line

with the bit until the fastener is seated at the desired depth

in theworkpiece.

Recommendations for Screwdriving

• Start with lower torque settings, then advance to higher

torque settings to avoid damage to the workpiece

orfastener.

• Make some practice runs in scrap or on unseen areas of the

workpiece to determine the proper position of the mode

selectioncollar.

Drilling

1. Turn the mode selection collar

6

to the drillsymbol. Refer

to ModeSelection.

2. Place drill bit in contact with theworkpiece.

NOTE: Use sharp drill bitonly.

3. Pull the trigger applying pressure in a straight line with the

bit until it reaches the desireddepth.



WARNING: Drill may stall if overloaded causing a sudden

twist. Always expect the stall. Grip the drill firmly to control

the twisting action and avoidinjury.

4. Keep the motor running when pulling the bit back out of a

drilled hole to preventjamming.

Recommendations for Drilling

• When drilling, always apply pressure in a straight line with

the bit, but do not push hard enough to stall the motor or

deflect thebit.

• IF THE DRILL STALLS:

- RELEASE TRIGGER SWITCH IMMEDIATELY, remove

drill bit from work, and determine cause ofstalling.

- DO NOT DEPRESS TRIGGER SWITCH ON AND OFF

IN AN ATTEMPT TO START A STALLED DRILL—THIS

CAN DAMAGE THEDRILL.

- To minimize stalling or breaking through the material,

reduce pressure on drill and ease the bit through the last

fractional part of thehole.

• Large holes (7.9 mm to 12.7 mm) in steel can be made

easier if a pilot hole (4 mm to 4.8mm) is drilledfirst.

• If drilling thin material or material that is prone to splinter,

use a wood “back-up” block to prevent damage to

theworkpiece.

Hammerdrilling



WARNING: Wear proper respiratory protection. Collect

residual dust with a vacuum or dust collection system

designed for the application.

DCD709 Only

IMPORTANT: Use carbide-tipped or masonry bits rated for

percussion drillingonly.

1. Select the desired speed/torque range using the speed

selector

7

to match the speed and torque to the planned

operation. Turn the mode selection collar

6

to the

hammerdrillsymbol.

2. Pull the trigger, applying just enough pressure on the

hammer to keep it from bouncing excessively or "rising" off

the bit.

ENGLISH

Recommendations for Hammerdrilling

• Too much force will cause slower drilling speeds,

overheating, and a lower drillingrate.

• A smooth even flow of material indicates the proper

drillingrate.

• Drill straight, keeping the bit at a right angle to the work. Do

not exert side pressure on the bit when drillling as this will

cause clogging of the bit flutes and a slower drillingspeed.

• When drilling deep holes, if the hammer speed starts to

drop off, pull the bit partially out of the hole with tool still

running to help clear debris from thehole.

MAINTENANCE

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can be recovered

or recycled reducing the demand for raw materials. Please

recycle electrical products and batteries according to local

provisions. Further information is available at www.2helpU.

com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

简体中文

恭喜！

感谢您选购

DeWALT

工具。凭借多年的产品开发和创新经验，

DeWALT

已经成为专业电动工具用户最可靠的合作伙伴之一。

技术参数

DCD708 DCD709

电压

伏特

直流

（最大

）

（最大

）

电池类型

锂离子锂离子

功率输出

瓦

340 340

空载转速

档

转/分

0–450

0–1650

0–450

0–1650

每分钟冲击数

档

– 0–7650

档

– 0–28050

最大扭矩（硬/软）

Nm 65

26 65

夹头尺寸

毫米

1.5–13 1.5–13

最大

钻孔

能力

木材

金属

砖石

毫米

–

重量（不含电池组）

千克

1.10 1.20

本信息表中所载的振动发射标准依据

IEC60335

提供的标准测试

测量，并且可用于工具间的比较。它可用于噪音的初步评估。



警告：我们所公布的振动发射级适用于本工具的主要应

用。然而，如果将本工具用于其他应用、为其使用不同的

配件或保养不当，则振动发射值可能会不同。这可能会大

幅度提高总工作时间内的噪音级。

在关闭工具电源、或运行中的工具实际上并未工作时，也应考虑

到其噪音级或振动。这可能会大幅度降低总工作期间的噪音级。

确定额外的安全措施以保护操作员免受振动影响，比如：保

养工具和配件、双手保持温暖、组织工作模式。

警告：为降低伤害风险，请阅读使用手册。

定义：安全指南

下列定义描述了各标志术语的严重程度。请仔细阅读本手册，并

注意这些标志。



危险：表示存在紧急危险情况，如果不加以避免，将导致

死亡或严重伤害。



警告：表示存在潜在的危险情况，如果不加以避免，可能

导致死亡或严重伤害。



警示：表示存在潜在危险情况，如果不加以避免，可能导

致轻度或中度伤害。

注意：表示存在不涉及人身伤害的情况，如果不加以避

免，可能导致财产损失。



表示存在触电风险。



表示存在火灾风险。

充电式紧凑型

毫米电钻/起子/冲击钻

DCD708

，

DCD709

电池

充电器

充电时间（分钟）

目录号伏特

直流

安时

重量

（千克）

DCB107 DCB112 DCB115 DCB118 DCB132

DCB546 18/54 6.0/2.0 1.05 270 170 90 60 90

DCB547 18/54 9.0/3.0 1.46 420 270 140 85 140

DCB548 18/54 12.0/4.0 1.44 540 350 180 180 120

DCB181 18 1.5 0.35 70 45 22 22 22

DCB182 18 4.0 0.61 185 120 60 60 60

DCB183/B 18 2.0 0.40 90 60 30 30 30

DCB184/B 18 5.0 0.62 240 150 75 75 75

DCB185 18 1.3 0.35 60 40 22 22 22

DCB187 18 3.0 0.54 140 90 45 45 45

DCB189 18 4.0 0.54 185 120 60 60 60

简体中文

电动工具通用安全警告



警告！阅读随电动工具提供的所有安全警告、说明、图示

和规定。不遵照以下所列说明会导致电击、着火和/或严

重伤害。

保存所有警告和说明书以备查阅。

警告中的术语

“

电动工具

”

指市电驱动（有线）电动工具或电池驱动（无线）

电动工具。

工作场地的安全

1 )

保持工作场地清洁和明亮。杂乱和黑暗的场地会引发事故。

2 )

不要在易爆环境，如有易燃液体、气体或粉尘的环境下

操作电动工具。电动工具产生的火花会点燃粉尘或气体。

3 )

操作电动工具时，远离儿童和旁观者。注意力不集中会使

你失去对工具的控制。

电气安全

1 )

电动工具插头必须与插座相配。绝不能以任何方式改装插头。

需接地的电动工具不能使用任何转换插头。未经改装的插头

和相配的插座将降低电击风险。

2 )

避免人体接触接地表面，如管道、散热片和冰箱。如果你

身体接触接地表面会增加电击风险。

3 )

不得将电动工具暴露在雨中或潮湿环境中。水进入电动

工具将增加电击风险。

4 )

不得滥用软线。绝不能用软线搬运、拉动电动工具或拔

出其插头。使软线远离热源、油、锐边或运动部件。受损

或缠绕的软线会增加电击风险。

5 )

当在户外使用电动工具时，使用适合户外使用的延长线。适合

户外使用的电线将降低电击风险。

6 )

如果无法避免在潮湿环境下操作电动工具，应使用带有剩余

电流装置

(RCD)

保护的电源。

RCD

的使用可降低电击风险。

人身安全

1 )

保持警觉，当操作电动工具时关注所从事的操作并保持

清醒。当你感到疲倦，或在有药物、酒精或治疗反应时，

不要操作电动工具。在操作电动工具时瞬间的疏忽会导

致严重人身伤害。

2 )

使用个人防护装置。始终佩戴护目镜。防护装置，诸如适

当条件下使用防尘面具、防滑安全鞋、安全帽、听力防护

等装置能减少人身伤害。

3 )

防止意外起动。在连接电源和/或电池盒、拿起或搬运工

具前确保开关处于关断位置。手指放在开关上搬运工具

或开关处于接通时通电会导致危险。

4 )

在电动工具接通之前，拿掉所有调节钥匙或扳手。遗留在

电动工具旋转零件上的扳手或钥匙会导致人身伤害。

5 )

手不要过分伸展。时刻注意立足点和身体平衡。这样能

在意外情况下能更好地控制住电动工具。

6 )

着装适当。不要穿宽松衣服或佩戴饰品。让你的头发和

衣服远离运动部件。宽松衣服、佩饰或长发可能会卷入

运动部件。

7 )

如果提供了与排屑、集尘设备连接用的装置，要确保其

连接完好且使用得当。使用集尘装置可降低尘屑引起的

危险。

8 )

不要因为频繁使用工具而产生的熟悉感而掉以轻心，忽视

工具的安全准则。某个粗心的动作可能在瞬间导致严重的

伤害。

电动工具使用和注意事项

1 )

不要勉强使用电动工具，根据用途使用合适的电动工具。

选用合适的按照额定值设计的电动工具会使你工作更有效、

更安全。

2 )

如果开关不能接通或关断电源，则不能使用该电动工具。

不能通过开关来控制的电动工具是危险的且必须进行修理。

3 )

在进行任何调节、更换附件或贮存电动工具之前，必须从

电源上拔掉插头和/或卸下电池包（如可拆卸）。这种防

护性的安全措施降低了电动工具意外起动的风险。

4 )

将闲置不用的电动工具贮存在儿童所及范围之外，并且不允

许不熟悉电动工具和不了解这些说明的人操作电动工具。

电动工具在未经培训的使用者手中是危险的。

5 )

维护电动工具及其附件。检查运动部件是否调整到位或卡

住，检查零件破损情况和影响电动工具运行的其他状况。

如有损坏，应在使用前修理好电动工具。许多事故是由维

护不良的电动工具引发的。

6 )

保持切削刀具锋利和清洁。维护良好地有锋利切削刃的

刀具不易卡住而且容易控制。

7 )

按照使用说明书，并考虑作业条件和要进行的作业来选

择电动工具、附件和工具的刀头等。将电动工具用于那些

与其用途不符的操作可能会导致危险情况。

8 )

保持手柄和握持表面干燥、清洁，不得沾有油脂。在意外的

情况下，湿滑的手柄不能保证握持的安全和对工具的控制。

电池式工具使用和注意事项：

1 )

仅使用生产者规定的充电器充电。将适用于某种电池包

的充电器用到其他电池包时可能会发生着火危险。

2 )

仅使用配有专用电池包的电动工具。使用其他电池包可能

会产生伤害和着火危险。

3 )

当电池包不用时，将它远离其他金属物体，例如回形针、硬

币、

钥匙、钉子、螺钉或其他小金属物体，以防电池包一

端与另一端连接。电池组端部短路会引起燃烧或着火。

4 )

在滥用条件下，液体可能会从电池组中溅出，应避免接触。如

果意外碰到液体，用水冲洗。如果液体碰到了眼睛，还要寻

求医疗帮助。从电池中溅出的液体可能会发生腐蚀或燃烧。

5 )

不要使用损坏或改装过的电池包或工具。损坏或改装过的

电池组可能呈现无法预测的结果，导致着火、爆炸或伤害。

6 )

不要将电池包暴露于火或者高温中。电池包暴露于火或高

于

130°C

的高温中可能导致爆炸。

维修

1 )

让专业维修人员使用相同的备件维修电动工具。这将保

证所维修的电动工具的安全。

2 )

决不能维修损坏的电池包。电池包仅能由生产者或其授

权的维修服务商进行维修。

电钻专用警告语：

使用冲击电钻时要戴好耳罩。暴露在噪声中会引起听力损伤。

使用随工具提供的辅助手柄。操作失手会引起人身伤害。

当在钻削附件可能触及暗线之处进行操作时，要通过绝缘握持面

来握持工具。钻削附件碰到带电导线会使工具外露的金属零件带

电从而使操作者受到电击。

使用长钻头的安全说明

•

切勿以高于钻头最大额定速度的速度运行。在较高的速度下，

如果允许在不接触工件的情况下自由旋转，钻头可能会弯曲，

从而导致人身伤害。

简体中文

•

始终以低速进行钻孔，钻头尖端与工件保持接触。在较高的速

度下，如果允许在不接触工件的情况下自由旋转，钻头可能会

弯曲，从而导致人身伤害。

•

仅在与钻头直接对齐时施加压力，并且不施加过大的压力。钻头

可能弯曲致破损或失控，从而导致人身伤害。

电钻/起子/电锤附加安全警告

•

使用夹具或采取其它可行的方法，将工件固定、支撑到稳定

的平台上。手持或用身体顶住工件都是不稳定的，会导致操

作失控。

•

附件和工具可能会在使用过程中发热。如果进行放热应用（如金

属钻孔），处理时请佩戴手套。

•

通风口通常会盖住运动部件，应予以避免。宽松衣服、佩饰或

长发可能会卷入运动部件。

•

请佩戴安全护目镜或其他护目装备。冲击或钻孔会导致碎片飞

散。飞散的颗粒会对眼睛造成永久性伤害。

•

使用冲击电钻时请佩戴听力保护器。暴露在噪声中会引起听

力损伤。

•

使用工具随附的辅助手柄。工具失控会导致人身伤害。

•

在切削附件可能触及暗线之处进行操作时，要通过绝缘握持

面来握持电动工具。切割配件如果接触到

“

带电

”

导线，电动工

具金属部件表面就会

“

带电

”

并使操作人员触电。

•

请勿长时间操作此工具。工具运行导致的振动可能会伤害您

的手和手臂。使用手套提供额外缓冲，经常停下休息，限制

使用时间。

剩余风险

尽管遵守了相关的安全法规并采用了安全装备，某些剩余风险仍

然是无法避免的。这些风险包括：

•

听力损伤。

•

飞溅颗粒造成的人身伤害风险。

•

使用时附件发热导致的灼伤风险。

•

长时间使用引起的人身伤害风险。

请妥善保管好这些说明

充电器

DeWALT

充电器无需做出任何调整，专为简易操作而设计。

电气安全

电机只适用一种工作电压。请务必检查电池组的电压是否和铭牌

上的电压一致。另外，请确保充电器电压和主电源的电压一致。

DeWALT

充电器符合

IEC60335

双重绝缘要求，因此无

需使用接地线。

若电源线损坏，必须交由

DeWALT

维修部门采用专门制备的电线

进行更换。

使用延长线

除非绝对必要，否则请勿使用延长线。使用适合您的充电器输入功

率的合格延长线（见

技术参数

）。最小的导线尺寸为

平方毫米；

最大长度为

米。

使用电缆卷筒时，请务必拉出所有的电缆

。

针对所有电池充电器的重要安全说明

请妥善保管好这些说明：

本手册包含重要的兼容电池充电器安全

和操作说明（请参阅

技术参数

）。

•

在使用充电器之前，请先阅读所有指示以及充电器、电池组和

使用电池组的产品上的警示标记。



警告：触电危险。请勿让任何液体渗入充电器，否则会引

起触电。



警告：我们建议使用漏电保护额定电流为

毫安或以下

的漏电保护装置。



警示：灼伤危险。为降低人身伤害风险，请仅使用

DeWALT

充电式电池充电。使用其它类型的电池可能会引起爆裂，并

导致人身伤害和损害。



警示：应看管好儿童，以确保他们不将此设备当做玩具来玩。

注意：在某些情况下，当充电器的插头插入电源插座时，充电

器内部裸露的充电接触点可能因为外来物件而短路。请勿让

能导电的异物靠近充电器腔，这些外来物件包括但不限于钢

棉、铝箔或任何金属颗粒的堆积物。充电器内没有电池组时，

请断开充电器与电源的连接。清洗前，务必拔掉充电器

。

•

请勿试图使用本手册指定的充电器以外的其他任何充电器为电

池组充电。充电器和电池组都是专门设计的，互相配合使用。

•

除了为

DeWALT

充电式电池充电以外，这些充电器并非设计

用于其他用途。否则，可能会导致火灾、触电或电击。

•

请勿将充电器暴露于雨中或雪中。

•

断开充电器连接时，应拔下插头，切勿拉拽电源线。这将降低

对电插头和电线的损害风险。

•

确保电源线布置在不易踩踏、踢绊、拉扯或会受到损害或压

力的位置。

•

除非绝对必要，否则请勿使用延长线。使用不正确的延长线

可能导致火灾、触电或电击的风险。

•

请勿将任何物件放在充电器上面，或是把充电器放在可能会

堵住通风槽的柔软表面，导致充电器的内部过热。请把充电

器放置在远离任何热源的地方。充电器通过外壳顶端和底端

的槽进行通风。

•

禁止使用电源线或插头已损坏的充电器。请立即更换这些

充电器。

•

如果充电器受到强烈重击、掉落或出现其他损坏情况，请勿

使用充电器。请将损坏的充电器送到授权服务中心。

•

请勿自行拆卸充电器。请将需要检修或修理的充电器送到授

权服务中心。重装不正确可能导致触电、电击或火灾风险。

•

必须立即将已损坏的电源线交由制造商、服务代理或类似的

合格人员进行更换以防止安全隐患。

•

清洁前，请先断开充电器和插座的连接，以降低触电风险。取出

电池组不会降低此风险。

•

切勿将两个充电器连接在一起。

•

充电器是为

220-240 V

的标准家用电源而设计。请勿试图在

任何其他电压下使用充电器。此规则不适用于车载充电器。

为电池充电（图

）

放进电池组前，先将充电器的插头插到相应的电源插座上。

将电池组

1

插入到充电器中，确定电池组完全就位。红色（充电

中）指示灯将不断闪烁，表示充电过程已经开始。

红色灯持续亮起表示充电完成。此时电池组已完全充电，您可

以使用电池组或将电池组留在充电器上。要从充电器上取下

电池组，请按下电池组上的电池释放按钮

2。

注：为了确保锂离子电池的效能和使用寿命最大化，在首次使用

电池组之前必须将其完全充电。

简体中文

充电器操作

关于电池组的充电状态，请参阅以下指示灯说明。

充电状态指示灯

充电中

已完全充电

热/冷电池组延迟

红色指示灯会继续闪烁，但黄色指示灯在本次操作过程中会亮起。

电池组达到适当温度后，黄色指示灯会熄灭，充电器将恢复充电

程序。

此兼容充电器不能为故障的电池组充电。充电器指示灯不亮时表

示电池有故障。

注：这也可能意味充电器有故障。

如果充电器提示存在故障，请将充电器和电池组送到授权的维修

中心进行测试。

热/冷电池组延迟

当充电器检测到电池组过热或过冷时，它会自动启动热

冷电池

延迟模式，暂停充电，直到电池组达到适当的温度。然后，充电器

会自动切换到电池组充电模式。此功能可确保电池组拥有最长的

使用寿命。

冷电池组充电速度比热电池组充电速度慢。电池组在整个充电周期

的充电速度都会较慢，即使电池组升温也不会恢复到最大速度。

DCB118

充电器配备专用于冷却电池组的内部风扇。电池组需要冷

却时，风扇会自动启动。如果风扇运转不正常或通风槽堵塞，切勿

操作充电器。请勿让异物进入充电器内部。

电子保护系统

锂离子电池工具具有电子保护系统设计，可保护电池组免受过

载、过热或过度放电之害。

如果电子保护系统处于运作状态，该工具将自动停止操作。如果发

生这种情况，请将锂离子电池组放在充电器上，直至其完全充电。

壁挂式安装

这些充电器设计为可以安装在墙上，也可以直立在桌面或工作台

面上。如果安装在墙上，请确保充电器的位置可以连接到电源插

座，并且远离墙角或其他可能妨碍空气流通的障碍物。将充电器背

面作为在墙上安装螺丝的位置模板。使用至少

25.4

毫米长、螺丝

帽直径至少

7-9

毫米的石膏板螺丝（单独购买）牢牢固定充电器，

将螺丝最大限度钉入木材，预留约

5.5

毫米露在墙外。将充电器背

面的安装槽对准露出的螺丝，完全放置到位。

充电器清洁说明



警告：触电危险。清洁前，请将充电器从交流电源插座上拔下。

可用布或非金属软刷清除充电器外部的污垢和油脂。请勿使用

水或任何清洁剂。切勿让任何液体渗入工具，切勿让工具的任

何部件浸在液体中。

电池组

针对所有电池组的重要安全说明

在订购更换电池组时，请务必附上目录型号和电压。

包装箱内的电池组并未完全充电。使用电池组和充电器之前，请阅

读下列安全指示，然后遵循所述的充电程序。

请阅读所有说明

•

请勿在易爆环境，如有易燃液体、气体或粉尘的环境中充电

或使用电池。在充电器中插入或取出电池时可能会点燃粉尘

或气体。

•

切勿强行将电池放进充电器。请勿以任何方式改装电池组以

在不相容的充电器中使用，否则电池组可能会破裂，导致严

重人身伤害。

•

只使用

DeWALT

充电器为电池组充电。

•

请勿喷溅电池组或将其浸泡在水或其他液体中。

•

请勿在温度可能达到或超过

40˚C

(104˚F)

的地方（如夏天

户外的棚子或金属建筑物中）存储或使用工具和电池组。

•

即使电池组严重受损或完全损坏，也请勿焚化电池组。电池

组在火中会发生爆炸。锂离子电池组在燃烧时会释放有毒烟

雾和物质。

•

如果电池液体接触到皮肤，请立即以中性肥皂和清水冲洗接

触的地方。如果电池液体不慎进入眼睛，应睁开眼睛并用清

水冲洗至少

分钟或直到刺激感消失。如果需要医疗救助，

请告知医护人员。电池电解质由液状有机碳酸盐和锂盐的混

合物组成。

•

已打开电池的内部物质可能导致呼吸道刺激。请保持空气流通。

如果症状持续存在，请就医。



警告：灼伤危险。电池液如果接触到火花或火焰可能会燃烧。



警告：切勿以任何理由试图打开电池组。电池组外壳破裂

或损坏时，请勿将电池组插入充电器。请勿挤压、掉落或

损坏电池组。请勿使用受过强烈重击、掉落、碾压或以任

何其它方式（如被钉子穿破、受到锤子的重击、踩踏）受

损的电池组或充电器。否则可能会引起触电或电击。损坏

的电池组应送回维修中心进行回收。



警告：火灾危险。请勿在存储或搬运电池组时让金属物品

接触暴露的电池两极。例如，请勿将电池组放在围裙、口

袋、工具盒、产品套件盒、抽屉等可能与散钉、螺丝、钥匙

等物品接触的地方。



警示：不用时，将工具侧放在平稳的表面上，确保不会有

踢绊或掉落的危险。一些具有大型电池组的工具可以直立

但可能会轻易被撞倒。

运输



警告：火灾危险。电池运输途中，如果电池两极意外接触

导电材料，可能会引发火灾。运输电池时，务必保护电池

两极，确保与可能接触电池导致短路的材料良好绝缘。

注：锂离子电池不应放在托运行李中。

DeWALT

电池符合所有适用的行业和法律标准规定的运输规范，

包括《联合国危险品运输建议规章范本》

(UN Recommendations

on the Transport of Dangerous Goods)

、《国际航空运输协会

(IATA)

危险品规则》

(International Air Transport Association (IATA)

Dangerous Goods Regulations)

、《国际海运危险品

(IMDG)

规则》

(International Maritime Dangerous Goods (IMDG) Regulations)

和《欧洲危险货物国际公路运输协定》

(European Agreement

Concerning The International Carriage of Dangerous Goods by

Road) (ADR)

。锂离子电池和电池组已遵循《联合国危险品运输建议

规章范本手册》第

38.3

节关于测试和标准的说明通过测试。

大多数情况下，发运

DeWALT

电池组不属于完全管制的

类危险

品。通常情况下，只有当运输包含一个能量等级大于

100

瓦时

(Wh)

的锂离子电池时，才需要作为完全管制的

类危险品发运。所有锂离

子电池外壳上均标注有瓦时等级。此外，由于法规比较复杂，无论瓦

简体中文

时等级是多少，

DeWALT

都不建议单独空运锂离子电池组。发运包含

电池的工具（组合套件）时，如果电池组的额定能量不大于

100

瓦时

(Wh)

，则可以空运。

无论发运是否纳入完全管制范围内，运输公司均有责任遵循最新法规

中关于包装、标签

标记和单据的要求。

本手册本节的信息是出于善意提供，且认为在编制文档时准确无误。

但是不提供明示或暗示的担保。购买方负有确保其行为遵守适用法

规的责任。

运输

FLEXVOLT

电池

DeWALT

FLEXVOLT

电池有两种模式：使用和运输。

使用模式：当

FLEXVOLT

电池单独使用或用于

DeWALT

伏产

品时，将作为

伏电池操作。当

FLEXVOLT

电池用于

伏或

108

伏（两个

伏电池）的产品时，将作为

伏电池进行操作。

运输模式：当电池盖连接到

FLEXVOLT

电池时，电池会进入运输模

式。保留电池盖用于运输。

处于运输模式时，电池组内部的电池

芯会处于断电状态，使

个低瓦时

(Wh)

等级的电池相当于

个高瓦时

等级电池。这样，增加

个低瓦时等

级的电池可以使电池组不必遵守适用于更高瓦时电池的运输法规。

例如，若运输额定瓦时为

3x36

瓦时，则表示

个

瓦时的电池。使用瓦时额定

值可能是

108

瓦时（表示

个电池）。

存放建议

最好将电池存放在阴凉、干燥、远离阳光直射、不会过热或过

冷的地方。为了获得最佳的电池性能和使用寿命，请您在不使

用电池组时将其存储在室温下。

长期存储时，建议将完全充电的电池组从充电器取出，存储在

阴凉、干燥的地方，以达到最佳效果。

注：电池组不应在电池已完全耗尽的状态下存放。使用电池组之

前，必须重新为电池组充电。

充电器和电池组上的标签

除了在本手册中所使用的标志，充电器和电池组的标签还包括：

使用前请阅读使用手册。

要了解充电时间，请参阅

技术参数

。

请勿使用导电物体戳刺。

请勿对损坏的电池组充电。

请勿将其暴露于水中。

应立即更换有缺陷的电线。

使用和运输标签标记示例

请只在

4°C

和

40°C

之间的温度下充电。

只能在室内使用。

弃置电池组时，请妥善处理以保护我们的环境。

只使用指定的

DeWALT

充电器为

DeWALT

电池组充

电。使用

DeWALT

充电器为非

DeWALT

电池充电可能

会导致电池爆炸或出现其他危险情况。

请勿焚化电池组。

使用（无电池盖）。示例：瓦时额定值为

108

瓦时

(

个

108

瓦时的电池)。

运输（有内置运输盖）。示例：瓦时额定值为

3 x 36

瓦时

(

个

瓦时的电池)。

电池类型

DCD708/DCD709

使用

伏特电池组。

这些电池组可用于：

DCB181

、

DCB182

、

DCB183

、

DCB183B

、

DCB184

、

DCB184B

、

DCB185

、

DCB187

、

DCB189

、

DCB546

、

DCB547

，

DCB548

。

更多信息，请参阅

技术参数

。

包装内的物品

包装内的物品包括：

只

电钻

起子

(DCD708)

或电锤

(DCD709)

只

充电器

只

皮带扣（部分型号内自带）

只

磁力钻头夹持器（部分型号内自带）

只

锂离子电池组（

、

型号）

只

锂离子电池组（

、

型号）

只

锂离子电池组（

、

型号）

本

说明手册

•

检查工具、部件或附件是否在运输过程中损坏。

•

操作前，请抽空仔细阅读并掌握本手册。

工具上的标记

工具上印有下列图形：

使用前请阅读使用手册。

请佩戴听力保护器。

请佩戴护目装备。

可见辐射。切勿直视激光束。

简体中文

日期码位置（图

）

日期码

14

印在工具外壳上，其中还包含制造年份。

示例：

2018 XX XX

制造年份

说明（图

）



警告：切勿改装电动工具或其任何部件，否则可能会导致

损坏或人身伤害。

电池组

电池组释放按钮

主手柄

变速触发开关

正/反转控制按钮

模式选择环

转速选择器

工作灯

夹头套管

无锁匙夹头

皮带扣（部分型号内自带）

螺丝

磁力钻头夹持器（部分型号内自带）

日期代码

设计用途

这些电钻

起子

冲击钻设计用于专业钻孔、冲击钻孔和螺丝安装。

请勿在潮湿环境中或在易燃液体或气体存在的环境中使用本工具。

这些电钻

起子

冲击钻是专业型电动工具。

请勿让儿童接触本工具。缺乏经验的操作员需要在监督下使用

本工具。

•

儿童和体弱者。在没有他人监督的情况下，儿童或体弱者不适

宜使用本产品。

•

本产品不适合体力、感官或智力不足以及缺乏经验、知识或技

能的人员（包括儿童）使用，除非一旁有能为他们的安全负责

的监督人员。不得在无人监管的情况下让儿童接触本产品。

组装与调整



警告：为降低严重的人身伤害风险，在进行任何调整或取

出/安装附加装置或附件之前，请关闭装置并取下电池组。

意外启动可能会导致人身伤害。



警告：请只使用

DeWALT

电池组和充电器。

插入或取出工具上的电池组（图

）

注：请确保您的电池组

1

已完全充电。

将电池组安装到工具手柄中

将电池组

1

对齐工具手柄内的轨道（图

）。

将电池组滑入手柄内，使其牢牢地固定在工具内，并确保您听

到其锁定到位的声音。

从工具中取出电池组

按下释放按钮

2，将电池组从工具手柄中稳妥地拉出。

按本手册充电器部分所述将电池组插入充电器中。

电池组电量计（图

）

一些

DeWALT

电池组带有一个包含三个绿色

LED

指示灯的电量

计，用于指示电池组内的剩余电量。

按下电量计按钮不松开，即可启动电量计。三个绿色

LED

指示灯

将以组合方式亮起，以指示剩余电量。当电池内的电量低于可用限

制时，电量计将不会亮起，电池将需要重新充电。

注：电量计仅指示电池组的剩余电量。它并不表示该工具的功能，

且将根据产品组件、温度和最终用户的使用情况而有所不同。

皮带扣和磁力钻头夹具（图

）

(

可选配件

)



警告：为降低严重的人身伤害风险，请不要将工具悬挂在

头顶上方或用皮带扣悬挂物品。只能使用工作皮带悬挂

工具的皮带扣。



警告：为了降低严重人身伤害的危险，请确保固定皮带扣

子的螺丝是牢固的。

重要信息：安装或更换皮带扣或磁力钻头夹持器时，只使用提供

的螺丝。务必拧紧螺丝。

可使用提供的螺丝

12

将皮带扣

11

和磁力钻头夹持器

13

装

到

工具的任意一侧，以方便习惯左手操作或习惯右手操作的用户使用。

如果不需要使用皮带扣或磁力钻头夹持器，则可将其从工具上拆除。

若要拆除皮带扣或磁力钻头夹持器，请取下固定它们的螺丝

12，

然后在另一边重新装上。务必拧紧螺丝。

将钻头或附件安装到无锁匙夹头中（图

）



警告：不要尝试通过握住夹头前端和打开工具来拧紧钻

头（或任何其它配件）。这可能会导致夹头受损和人身伤

害。更换配件时，请始终锁定触发开关并断开工具的电

源连接。



警告：启动工具之前应确保钻头安装稳固。松动的钻头可

能会从工具脱落，从而可能导致人身伤害。

您的工具备有无锁匙夹头

10，带有一个旋转套管

9，便于单手操

作夹头。如果要插入钻头或其他配件，请执行下列步骤。

关闭电源并取下电池组。

用一只手抓住夹头的黑色套管，用另一只手固定工具。逆时针

旋转套管以插入所需的配件。

将附件插入夹头约

毫米，然后用一只手顺时针旋转夹头，

另一只手则握住工具，将附件转紧。您的工具配备一个自动主

轴锁装置。凭借此装置，您只需一只手即可打开和关闭夹头。

请确保在拧紧夹头时用一只手握住夹头套管，用另一只手握住工

具，以获得最大的紧密性。

若要松开附件，请重复上述步骤

和

。

转速选择（图

）

该工具有两种速度设置，可用于不同作业场景。

注：工具运行时切勿更改速度。在更改速度之前，务必等待工具

完全停止。

若要选择速度

（高扭矩设置），请关闭工具并让它停止转动。

向后滑动转速选择器

7

(远离夹头)

。

若要选择速度

（高速设置），请关闭工具并让它停止转动。向前

滑动转速选择器

7

(滑向夹头)

。

如果工具没有改变速度，请确认转速选择开关完全啮合在前进或

后退位置。

ページが読み込まれています...

DeWalt DCD709 ユーザーマニュアル

ブランド: DeWalt

モデル: DCD709

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

このマニュアルも適しています

PDFをダウンロードします

報告

その他のドキュメント

Stanley SBI810D2K ユーザーマニュアル

DeWalt DCD709 ユーザーマニュアル

このマニュアルも適しています

DeWalt DCD709 ユーザーマニュアル

関連論文

その他のドキュメント