01 02 03 04 05 06
EN
LED Light Bar Status
Solid blue for 4 seconds,
then turns off Connected to power
Solid blue for 5 seconds,
then turns off Charging your device
Flashing blue quickly Metal or abnormal objects detected
The right and left lights:
Solid blue
The middle light: Flashing
blue
Overvoltage or undervoltage protection activated
T
• You cannot charge your device wirelessly in these scenarios:
When using a case with a magnetic/iron plate;
When using a case with a pop socket;
When using an ultra-thick (> 5 mm) protective phone case.
• Connect the wireless charger to a Quick Charge 2.0/3.0 or Power
Delivery wall adapter. Do not connect to a 5V/1A wall charger or
a USB port on a computer as it may affect the wireless charging
function.
• Do not place any foreign objects between your device and the
wireless charger’s surface, including metal pads on a car mount,
magnetic cards, door keys, coins, NFC cards or other metal
objects, as they could potentially demagnetize the wireless
charger, affect the charging speed, or cause overheating.
• Wireless chargers make charging more convenient than wired
chargers, but confined by current wireless technology, their
charging speed is slower than that of wired chargers.
• High temperatures will reduce charging speed and restrict power.
It is recommended that you charge your device in environments
with temperatures below 40°C / 104°F.
Important Safety Instructions
Please refer to the electrical and safety information on the
bottom before installing or operating the product.
• Avoid dropping.
• Do not disassemble.
• Do not expose to liquids.
• For the safest and fastest charge, use original or certified cables.
• This product is suitable for moderate climates only.
• The maximum ambient temperature during use of this product must not
exceed 40°C.
• Open flame sources, such as candles, must not be placed on this product.
• Only use a dry cloth or brush to clean this product.
• The socket-outlet shall be installed near the product and shall be easily
accessible.
• Disconnection from line voltage should be made via the AC plug.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
(1) Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio / TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 cm between the radiator and your body.
Product Name: Anker 533 Wireless Charger (3-in-1 Stand)
Model: A2538
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1 800 988 7973
IC Caution
Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence
conformes aux RSS (RSS) d'Innovation, Sciences et Développement
économique Canada. Le fonctionnement est soumis aux deux conditions
suivantes:
(1) Cet appareil ne doit pas causer d'interférences.
(2) Cet appareil doit accepter toutes les interférences, y compris celles
susceptibles de provoquer un fonctionnement indésirable de l'appareil.
RF exposure statement:
The equipment complies with IC Radiation exposure limits set forth for
uncontrolled environments. This equipment should be installed and operated
with a minimum distance of 10cm between the radiator and your body.
Déclaration d'exposition RF:
L'équipement est conforme à la limite d'exposition aux radiations de la
IC établie pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec une distance minimale de 10 cm entre le radiateur et
votre corps.
This product complies with the radio interference requirements
of the European Community.
To comply with RF exposure requirements, a minimum separation distance
of 20cm must be maintained between the user’s body and the product.
This device in compliance with the essential requirements and other relevant
provisions of Directive 2014/53/EU. All essential radio test suites have been
carried out.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2538
is in compliance with Directives 2014/53/EU & 2011/65/EU. The full text
of the EU declaration of conformity is available at the following internet
address:
https://www.anker.com/
This device in compliance with the essential requirements and other relevant
provisions of UKCA. All essential radio test suites have been carried out.
1.The device complies with RF specifications when the device used at 20cm
form your body.
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2538 is
in compliance with following Directives: Radio Equipment Regulations 2017,
Electrical Equipment (Safety) Regulations 2016 and The Restriction of the
Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012. The full text of the UK declaration of conformity is
available at the following internet address:
https://www.anker.com/
Specifications
Input 9V 2A / 9V 3A
Output
Wireless: 5W / 7.5W / 10W (for phones)
5W Max (for earbuds)
USB-A: 5V 1A
Operating Temperature -10°C - 40°C
Radiated H-Field
Radiated H-Field(for phones):9.44dBuA/
m(@10m)
Radiated H-Field (for earbuds) :-1.7dBuA/
m(@10m)
TX/RX Frequency Range 110-205KHz (for EU / UK only)
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon,
Hong Kong
The following importer is the responsible party (contract for EU and UK
matters)
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Ltd
Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA,
United Kingdom
This symbol indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and
electronic equipment.
DE
LED-Anzeigenleiste Status
Leuchtet 4Sekunden
lang blau, geht dann
aus Mit der Stromversorgung verbunden
Leuchtet 5Sekunden
lang blau, geht dann
aus
Ihr Gerät wird aufgeladen
Blinkt langsam blau Metall- oder anormale Objekte erkannt
Die rechte und linke
Anzeige: Leuchtet blau
Die mittlere Anzeige:
Blinkt blau
Überspannungs- oder Unterspannungsschutz
aktiviert
T
• In den folgenden Szenarien können Sie Ihr Gerät nicht drahtlos
aufladen:
Bei Verwendung einer Schutzhülle mit Magnet-/Eisenplatte,
Bei Verwendung einer Schutzhülle mit Sockel/Griff,
Bei Verwendung einer ultradicken (> 5 mm) Schutzhülle.
• Schließen Sie das kabellose Ladegerät an einen Quick Charge
2.0/3.0- oder Power Delivery-Wandadapter an. Schließen
Sie das Gerät nicht an ein 5 V/1 A-Wandladegerät oder einen
USB-Anschluss eines Computers an, da dies die Funktion zum
kabellosen Aufladen beeinträchtigen kann.
• Legen Sie keine Fremdkörper zwischen Ihr Gerät und die
Oberfläche des kabellosen Ladegeräts, einschließlich Metallpads
an einer Kfz-Halterung, Magnetkarten, Türschlüssel, Münzen,
NFC-Karten oder andere Metallgegenstände, da diese das
kabellose Ladegerät möglicherweise entmagnetisieren, die
Ladegeschwindigkeit beeinträchtigen oder eine Überhitzung
verursachen können.
• Kabellose Ladegeräte machen das Aufladen praktischer
als Ladegeräte mit Kabel, haben aber eine langsamere
Ladegeschwindigkeit als Ladegeräte mit Kabel, da sie durch die
aktuelle kabellose Technologie eingeschränkt sind.
• Hohe Temperaturen verringern die Ladegeschwindigkeit und
schränken die Leistung ein. Es wird empfohlen, dass Sie Ihr Gerät
in Umgebungen mit Temperaturen unter 40°C aufladen.
Wichtige Sicherheitshinweise
Lesen Sie die elektrischen und Sicherheitsinformationen unten,
bevor Sie das Produkt installieren oder betreiben.
• Nicht fallen lassen.
• Nicht auseinanderbauen.
• Keinen Flüssigkeiten aussetzen.
• Verwenden Sie für das sicherste und schnellste Aufladen Original- oder
zertifizierte Kabel.
• Das Produkt ist nur zur Verwendung in gemäßigten Klimazonen konzipiert.
• Die maximale Umgebungstemperatur während der Verwendung des
Produkts darf 40°C nicht übersteigen.
• Offene Flammen wie z.B. Kerzen dürfen nicht auf das Produkt gestellt
werden.
• Reinigen Sie das Produkt nur mit einem trockenen Tuch oder einem Pinsel.
• Die Steckdose muss in der Nähe des Produkt installiert werden und leicht
zugänglich sein.
Product Number: A2538 51005003171 V02
For FAQs and more information, please visit:
anker.com/support
@Anker Deutschland
@Anker Japan
@Anker
@AnkerOcial
@Anker_JP
@anker_ocial
@anker_jp
Product Number: A2538 51005003171 V02
For FAQs and more information, please visit:
anker.com/support
@Anker Deutschland
@Anker Japan
@Anker
@AnkerOcial
@Anker_JP
@anker_ocial
@anker_jp
