歡迎關注Phrozen社群獲取最新消息，並訂閱Phrozen YouTube頻道，觀看更多3D列印機教學。
如有任何疑問，請隨時與我們聯繫。
▎按鍵 S 為預設模式 ▎按鍵 M 為手動模式
此模式可快速選擇三種預設固化時間，分
別為5分鐘、10分鐘及20分鐘。
按下按鍵M後，點擊上下鍵每次可增減1分
鐘。長按上下鍵，則可快速增減分鐘數。
設定固化時間
02
▎開啟機台電源 ▎關閉機台電源
接上電源線，按下 Power 按鈕。 長按 Power 按鈕，聽到嗶聲後，固化燈
電源即關閉。
啟動電源及開關
01
關上機台遮光門，按下 Power 按鈕，固
化燈即開始運轉。
固化燈運轉
03
固化燈使用說明
▎8歲以上兒童、肢體及行為障礙者需在法定監護人的指導下使用本
產品，以確保使用者知悉所涉及的風險。禁止兒童在沒有監護人的
陪同下使用本產品。
▎未經法定監護人陪同，禁止兒童清潔或維護本產品。
如需外觀清潔請用酒精擦拭，請勿用油性或腐蝕性的液
體擦拭。
保養方式
▎固化燈需確實關上遮光門，才
能啟動固化燈。
▎請勿在未關上遮光門的情況下
直視固化燈光源，以免造成眼
部損傷。
注 意 事 項
Power
Pause
Power
Pause
Power
Pause
S
M
Power
Pause
Power
Pause
Power
Pause
S
M
Power
Pause
CURING LAMP (V2)
To Set Curing Time
02
Power
Pause
Power
Pause
▎Click the button S for preset
modes
▎Click the button M for custom
mode
This comes with three curing time
settings: 5 min, 10 min, 20 min.
Click on the up and down keys to
increase or decrease 1 minute each
time. Long press the keys to quickly
increase or decrease the minutes.
▎Turn on the device ▎Turn off the device
Connect the power cable. Press the
Power button to turn on the device.
Long press the Power button. The curing
lamp will turn off after a beep sound.
Power Supply & Light Switch
01
Power
Pause
Please follow Phrozen’s social media accounts and subscribe to our YouTube channel to learn more about printing tips and share ideas with one another.
Feel free to contact us if you have any questions.
Close the UV lamp cover. Click on the
Power button. The curing lamp will begin
operation.
How to Operate
the UV Curing Lamp
03
Warning
UV Curing Lamp User Guide
S
M
Power
Pause
Power
Pause
S
M
Power
Pause
Power
Pause
This appliance can be used by children aged 8 and above as well as by persons
with reduced physical, sensory, or mental capabilities, if supervised or given
instruction regarding the use of the appliance in a safe way, to ensure that the
hazards involved are understood. Children are NOT allowed to play with the
appliance.
Children are NOT allowed to clean or provide device maintenance without adult
supervision.
Do not stare at the UV curing lights
without closing the UV lamp as this
may cause damage to your eyes.
The UV lamp needs to be closed
completely for the device to begin
operation.
Standard Maintenance Procedure
Please use sanitizing alcohol to clean the outside of your device. Do not use any
oily or corrosive liquids to clean the device.
CURING LAMP (V2)
/
