CS-10EM
The CS-10EM is a microphone/earphone that combines back-electret stereo
microphones with in-ear headphones, allowing you to make binaural recordings
when the CS-10EM is inserted in your ears.
* Before using this product, carefully read the sections entitled: “Using the Unit
Safely” and “Important Notes.” These sections provide important information
concerning the proper operation of the product. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your
new product, this manual should be read in its entirety. The manual should be
saved and kept on hand as a convenient reference.
Connecting to Your Recorder
Red: Microphone plug
Connect this to the mic
input jack of your recorder.
Black: Earphone plug
Connect this to the
headphone jack.
Wearing the Earphones
Exchanging the Ear Pieces
* The CS-10EM’s microphones use plug-in power. They cannot be used with a
device that does not provide plug-in power. You must make sure that the mic
input jack of the device to which the CS-10EM is connected is a 3.5 mm stereo
mini, plug-in powered jack.
* If you’re using an EDIROL R-09 series or Roland R-09/R-05 series unit, turn on
the plug-in power of the R-05/R-09 series unit.
* You must minimize the volume before making connections. If the volume of
the connected device is raised when you make connections, you might
damage the earphones, cause acoustic feedback, or cause some other
problem with your playback system.
* To prevent cable breakage, grasp the base of the plug when connecting or
disconnecting it.
Slide tube
The earphones will stay in your ears more securely if
you adjust the slide tube to the appropriate position.
The CS-10EM will sound dierently depending on
how tightly the ear piece is inserted in your ear.
In order to enjoy the best possible sound, insert
the ear piece so that it ts snugly and is
suciently inside your ear.
When shipped from the factory, the M-size ear
pieces are attached. If the ear pieces do not t
your ears, try exchanging them with the included
L-size or S-size ear pieces.
To remove the ear piece, grasp the main body of
the earphone, and gently pull the tip of the ear
piece.
* Make sure to turn the volume control for the headphones all the way down
before you put them on. Otherwise, if the volume is at a raised level when you
put on the headphones, you risk harming your ears due to unexpected
acoustical feedback or contact noise produced when putting on the
headphones.
Owner’s Manual
Binaural Microphones/Earphones
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trademark of ROLAND CORPORATION in the United States and/or other countries.
* 5 1 0 0 0 1 3 4 0 0 - 0 1 *
Ear Piece
Main Body of
the Earphone
L: Left
R: Right
For EU Countries
For China
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For C.A. US
(
Proposition 65
)
Caution when recording
• Since this device contains a microphone and earphone in a single unit, acoustic feedback
may occur if you turn on a recording monitoring function and raise the recording level or
headphone volume. Acoustic feedback is also more likely to occur if you cover the unit
with the palm of your hand.
High-volume acoustic feedback may damage your hearing, so please adjust the volume to
an appropriate level.
• If you use this device near a computer or other electronic device, or connect it to a
recorder that is connected to an AC adaptor, noise might be heard in the recording. In this
case, move away from the electronic device, or operate your recorder on battery power.
• The microphone section is designed to minimize contact noise from the cable, but contact
noise might be heard if the cable is subjected to excessively rough handling.
• The microphone section is designed to minimize wind noise, but wind noise might be
heard in conditions of strong wind.
Specications
Using the Unit Safely
Important Notes
* Do not disassemble or modify this device.
* Do not drop this device, or subject it to strong impact.
* Do not subject this device to strong impact during use, or use it at high volume for an
extended period of time. Doing so may cause permanent damage to your hearing. If you
notice any loss of hearing or any ringing in your ears, immediately stop using this product,
and consult an audiologist.
* In the interests of traffic safety, never use this device while driving a car or other vehicle.
* When using this device as earphones, do not use it in locations where it might be
hazardous for you to be unable to hear surrounding sounds (e.g., at a railroad crossing or
railroad platform, in a factory, or on a street with passing cars).
* This device cannot be used with a personal computer.
* If you experience any abnormality in a place where this device contacts your skin, stop
using the device.
* When using this device on public transportation or in a public place, please be
considerate in avoiding possible annoyance to other people.
* To avoid possible breakage, do not leave this device connected to a recorder unit when
transporting it.
* To avoid breaking the cables, grasp the plug or the body of the earphone unit when
handling it.
* Do not leave this device in direct sunlight, near a device that emits heat, or in a closed
automobile. Doing so may cause deformation or fading.
* If cleaning is required, wipe the device with a soft dry cloth.
* Keep the included or detached ear pieces out of the reach of children so that they will not
be swallowed accidentally.
Microphone
• Element: Electret Condenser
• Polar Pattern: Omnidirectional
• Frequency Response: 20–20,000 Hz
• Open Circuit Sensitivity: -40 dB 1V/Pa
• S/N: Greater Than 60 dB
• Impedance: 2.2 kΩ
• Current Consumption: 500 μA
• Power Requirements: 2 V–10 V
• Weight: 4.5g (without cord)
• Cord: 1.5 m
• Plug: Stereo mini (gold-plated) x 2
• Accessories: Carrying Pouch, Ear pieces (S, M, L)
Earphone
• Type of Construction: Dynamic
• Driver: φ12.5mm
• Sensitivity: 102 dB/1mW, 500 Hz
• Maximum Input: 200 mA
• Frequency Response: 15–22,000 Hz
• Impedance: 16 Ω
* In the interest of product improvement, the specications and/or appearance of this unit
are subject to change without prior notice.
-
1
-
2
