User manual
Ver. A 1.0
Wireless HD Transmitter
& Receiver Kit
Thank you for purchasing the products, For optimum operation,
please read this manual carefully before use.
Preface
Size:100*57mm
Connection Diagram
Function Settings
1. Search for receiver in Wireless Network
(Name is RX-XXXX, default password is 12345678)
2. Open the mobile / tablet browser and enter 192.168.203.1 in the
address bar
3. After entering the website, you can operate the distribution network,
resolution,upgrade and restart
Problem solving
Q: How to restore factory settings?
A: When the product fails, press and hold the receiver function button
for 10 seconds. After a black screen appears and restart, the factory
settings will be restored.
Q: Can devices without HD interface be used?
A: Yes, please use the device with an HD interface converter.
Q: How to enter privacy mode?
A: Tap the transmitter function button to disconnect or reconnect.
1. Connect the HD port of the receiver to the video input port of the
display device such as the monitor or TV.
2. Connect the USB-C power supply port of the receiver to the charging
cable and plug it into the power adapter ( Voltage above 5V, current above
2A). Turn on the Receiver power switch.
3. Adjust the HD Signal source of the monitor or TV to the corresponding
HD port untithe boot screen is displayed.
4. Connect the transmitter to the computer or other devices With HD video
output function . After the indicator Light enters the fast flash state , Wait
for ten seconds to complete Casting.
*Please make sure that the power of the computer is sufficient. If the
power supply of the computer is insufficient or HD is unable to supply
power , please connect the transmitter to the power adapter or
USB-C power supply port ( Voltage above 5V , current above 2A )
使用手册
Ver. A 1.0
智能HD无线传输系统
尊敬的用户, 感谢您选购我们的产品。为了能更进一步了
解本产品, 使用前请仔细阅读本说明书。祝您体验愉快!
前言
接收器-RX
Receiver-RX
Transmitter-TX
发射器-TX
1. Please Press the receiver function button for more than 3 seconds, and
the prompt will pop up on the interface : Release the button to pair With
Ezcast TX. Wait for the transmitter to enter pairing mode
2. Press the transmitter function button for more than 5 seconds , the
indicator will flash for pairing , and Wait for the transmitter indicator to be
always on,indicating that the connection is successful.
接收器[RX] - 功能键
发射器[TX] - 功能键
Receiver[RX] - Function Button
Transmitter[TX] - Function Button
Transmitter Indicator Status
连接示意图
硬件投屏
接收器+发射器组合使用，即插即用
1. 将接收器的HD口连接到显示器或电视等显示设备的视
频输入口。
2. 将接收器的USB-C供电口连接充电线，插入电源适配
器或 USB-C供电口(电压5V电流2A),打开接收器电源
开关。
3. 将显示器或电视的HD信号源调整到相应的HD口，直
到接收器开机画面显示，开机成功。
4. 将发射器接入电脑或其它具有HD功能视频输出功能的
设备。指示灯进入快闪状态后等待十几秒，完成投射。
* 请务必保证电脑电量充足，如果电脑供电不足或者HD无
法供电，请将发射器的电源插入适配器上或者USB-C供
电口(电压5V电流2A)。
配对说明
产品在出厂时已完成配对。使用过程中操作不当或其它情况
造成配对失败，需对设备进行恢复重新配对的步骤如下:
1. 请按住接收器功能键3秒钟以上，界面弹出提示语:
Release the button to pair with EZCast TX。等待发射
器进入配对模式。
2. 按住发射器功能键5秒钟以上，指示灯出现快闪进行配对，
等待发射器指示灯常亮表示连接成功。
* 一收多发，1个接收器可配对8个发射器切换使用。
发射器指示灯状态
慢闪 未连接
配对中
已连接
快闪
常亮
功能设置
1. 在无线网络中搜索到接收器（名称是RX-XXXX，默认
密码为12345678)
2. 打开手机/平板浏览器，在地址栏输入192.168.203.1
3. 可以进行配网、分辨率、升级及重启等操作
问题解答
Q: 如何恢复出厂设置?
A: 当产品出现故障时，长按接收器功能键10秒，出现
黑屏重启后，即恢复出厂设置。
Q: 没有HD接口的设备可以使用?
A: 可以的，设备请配合HD接口转换器使用。
Q: 如何进入隐私模式?
A: 轻按发射器功能键，即可断开或回连。
Hardware Casting
Combination of receiver and transmitter, plug and play
Pairing Instructions
The product has been paired out of the factory. In case of pairing failure
due to improper operation or other circumstances during use, it is
necessary to restore and re pair the device as follows:
Slow Flash Disconnected
Fast Flash Pairing
Always On Connected
* With one receiver and multiple transmitters, 1 receiver can pair with
8 transmitters for switching.
USB-C
供电口
指示灯
功能键
HD接口
USB-C Power
Supply Port
Indicator
Light
Function
Button
HD
功能键
指示灯
HD
USB-C供电口
Function
Button
Indicator
Light
USB-C Power
Supply Port
HD
/
