comica BoomX-D 取扱説明書

User Manual

2.4G Digital 1-Trigger-2 Wireless Microphone

Foreword

Main Features

Thanks for purchasing COMICA BoomX-D 2.4G Digital 1-Trigger-2 Wireless Microphone.

To ensure bring you a good using experience, please read this manual book carefully before using and correctly

install and operate.

. 2.4G Digital Wireless, Global Free Frequency

. Dual Transmitters Triggered by One Receiver

. Visual Power, Audio Dynamic Monitor and

Other Display Functions

. Internal and External MIC Two Input Modes

. Mono/Stereo Switchable Output Modes

. Real-time Audio Monitor

. Broadcasting Quality Audio

. RF Technology, Auto Freq. Adjustment, Stable Transmission

. Low Latency < 20ms

. Working Range Up to 50m

. Designed with Multi-functional Belt Clip and Compact

1

Notice

Due to 2.4G wireless characteristics, please keep face to face when use it, and don’t turn your back to the

receiver, otherwise it is easy to generate breakpoints, which is a normal phenomenon

Don't block the antenna position to avoid any poor signal generated

Please attention that it can not realize STEREO function when in one-trigger-one mode

3.5mm TRS-TRS Audio Cable is suitable for Canon, Nikon and other cameras with low sensitivity

3.5mm TRS-TRS Audio Output Cable with Impedance is suitable for Sony, Panasonic, Fujiﬁlm and other cameras

with high sensitivity(3.5mm TRS-TRS Audio Output Cable with Impedance is recommended to be used if there is

sound explosive in recording )

When using on mobile phone, please turn o WIFI and Bluetooth to avoid 2.4G wireless interference

This product belongs to high-precision instruments, please avoid falling, collision or pounding

Do not use this equipment in the vicinity of heat source or interference source, such as radiator, oven, refrigerator

or air conditioner, smartphone or next to the WIFI AP

If the pick-up distance is close or when used outdoors, please put on the wind mu to prevent sound burst or

reduce wind noise

Do not use the equipment in rain or in a damp environment to avoid short-circuit danger

Please keep the product in a dry environment

2

UC Receiver (UC RX)Receiver (RX)Transmitter(TX)

Please keep face to face when use it, and don’t turn your back to the receiver, otherwise it is easy to generate

breakpoints.

Don't block the antenna position to avoid any poor signal generated.

Face to receiver (correct)

Antenna position Antenna position

Antenna position

Back to receiver (incorrect)

3

Packing List

D1 = TX + RX D2 = TX + TX + RX UC1 = TX + UC RX UC2 = TX + TX + UC RX

UC Receiver (UC RX)Receiver (RX) Transmitter(TX)

Multiple Selections:

Main Parts:

4

3.5mm Mic Audio Input Cable

Wind Mu

3.5mm TRS-TRRS Audio Cable (For Smartphone)

3.5mm TRS-TRS Audio Output Cable (For Canon, Nikon, etc.)

3.5mm TRS-TRS Audio Output Cable with Impedance(For Sony, Panasonic, Fujiﬁlm, etc.)

USB A-USB C Charging Cable

Reset Pin

User Manual

Warranty Card

The accessories of each combination include:

Accessories:

① + ② + ③ + ④ + ⑤ + ⑥ + ⑦ + ⑧ + ⑨

D1=

①x2 + ②x2 + ③ + ④ + ⑤ + ⑥ + ⑦ + ⑧ + ⑨

D2=

① + ② + ⑥ + ⑦ + ⑧ + ⑨

UC1=

①x2 + ②x2 + ⑥ + ⑦ + ⑧ + ⑨

UC2=

7 8 96543

21

1

2

3

4

5

6

7

8

9

User Manual

2.4G Digital 1-Trigger-2 Wireless Microphone

5

Components and Instruction

Transmitter (TX)

1. External Mic Locking Buckle

2. 3.5mm TRS Port of External Mic

3. Internal Mic

4. Power/Muting Button

5. Pair Button

6. Belt Clip

7. USB-C Charging Port

8. Reset Hole

2

3

6

4

7

8

5

1

6

Receiver (RX)

1. 3.5mm TRS/TRRS Monitoring Port

2. 3.5mm TRS Audio Output Port

3. Reset Hole

4. Power and M/S Button

5. A Channel Output Gain Control Button

6. B Channel Output Gain Control Button

7. Belt Clip

8. USB-C Charging Port

2

3

6

4

7

8

5

1

7

UC Receiver (UC RX)

1. USB-C Connector

2. Output Volume Adjustment Button

3. Group A Working Status Indicator

4. Group B Working Status Indicator

5. M/S Adjustment Button

6. 3.5mm TRS/TRRS Monitoring Port

2

3

4

5

6

1

8

Installation

Transmitter (TX)

1.Use internal microphone :

Install the transmitter on the collar through the belt clip so that the internal microphone points in the direction

of the sound source.

Internal Mic

Belt Clip

For better concealment during use, it is recommended that the belt clip be ﬁxed and used outwards.

9

2.Use external microphone:

Insert the 3.5mm TRS microphone input cable into the transmitter's 3.5mm TRS external microphone port and

tighten it, then clip the transmitter to the belt through the belt clip and clip the lavalier microphone to your

collar.

When using an external microphone, the internal microphone is automatically turned o.

10

1.Work with Camera:

Fix the receiver through the belt clip to the camera's hot shoe mount, then connect the receiver with camera

through the 3.5mm TRS-TRS audio cable; Insert the headphone into the monitoring port for monitoring.

Receiver (RX)

3.5mm TRS-TRS Audio Cable 11

2.Work with Smartphone:

Clip the receiver to the cold shoe mount through the belt clip; Connect the receiver with the mobile phone

through the 3.5mm TRS-TRRS audio cable and pay attention to the access to the audio output jack of the

receiver is the 3.5mm TRS plug, and the access to the mobile phone is the 3.5mm TRRS plug; Insert the

headphone to the 3.5 mm TRS/TRRS monitoring port for monitoring.

TRRS Plug

TRS Plug 3.5mm TRS-TRRS Audio Cable

In the absence of a mobile phone holder, the receiver can be

clamped to the mobile phone through the belt clip, and the

installation methods of other accessories are the same as

above.

12

Insert the UC receiver (UC RX) into the USB-C port of the phone; Insert the headphone into the 3.5mm

TRS/TRRS monitoring port for monitoring.

UC Receiver (UC RX)

13

Function and Usage

Transmitter (TX)

1.Screen Display Instruction:

A/B Channel Microphone Audio Dynamic Bar

Muting

Microphone Normal Working

Unpaired

in the Pairing

Paired Transmitter Battery Status

Signal Strength

A/B Channel is Connected

A/B Channel is not Connected

14

2.Function Introduction:

Long press for On/O; Short press for muting switch( Muting switch is available only when the screen is on,

if the screen is dimmed, press any button to light up the screen then switch the mute).

2.1. Power/Muting Button

Long press for pairing with receiver (Pairing switch is available only when the screen is on, if the screen is

dimmed, press any button to light up the screen then pairing).

2.2. Pair Button

Connect the transmitter with the power through the USB A-USB C charging cable to charge.

2.3. USB-C Charging Port

15

If there is an abnormal phenomenon such as the device is crash or unable to turn on it, then insert the reset

pin into the reset hole to reset it.

2.4. Reset Hole

Insert the 3.5mm TRS microphone input cable, and you can use the external lavalier microphone for

recording. At this time, the internal microphone of this device is turned o.

2.5. 3.5mm TRS Microphone Port

16

Mono/Stereo Receiver Battery Status

A channel is connected

A channel is not connected

A Channel Microphone Audio Dynamic Bar B Channel Microphone Audio Dynamic Bar

Group A Output Volume

Group B Output Volume

B channel is connected

B channel is not connected

Receiver (RX)

1.Screen Display Instruction:

17

2.Function Introduction:

Long press for On/O; Short press for mono and stereo mode switch. Please attention that it can not realize

STEREO function when in one-trigger-one mode.

(Mono/Stereo switch is available only when the screen is on, if the screen is dimmed, press any button to

light up the screen then switch the M/S)

2.2. Power and M/S Button

Short press to cyclically adjust the A/ B channel output Volume. It can independently adjust even in the

mono mode and is generally adjusted to the consistent output Volume when in use. (The output Volume

adjustment is available only when the screen is on, and if the screen is dimmed, press any button to light

up the screen and then adjust again).

2.3. A/B Channel Output Volume Adjustment Button

If there is an abnormal phenomenon such as the device is crash or unable to turn on it, then insert the reset

pin into the reset hole to reset it.

2.1. Reset Hole

18

ページを読み込んでいます...

comica BoomX-D 取扱説明書

関連論文

その他の書類