Gigabyte GC-ALPINE RIDGE 取扱説明書

GC-ALPINE RIDGE

Installation Guide/

12WE6-ALPINER-10AR

- 2 -

Chip Intel® DSL6540 Thunderbolt™ 3 Controller

Connectors

 2 x Thunderbolt

™

3 ports (Thunderbolt

™

3 Port 1/Thunderbolt

™

3 Port

2), supporting up to 40 Gbps bandwidth and a maximum display

resolution of 4096x2304@60 Hz

* Actual resolutions supported are dependent on the graphics card

being used.

 1 x HDMI port, supporting a maximum resolution of 4096x2160@24 Hz

* Support for HDMI 1.4 version.

 2 x Mini-DisplayPort In ports (DP IN 1/DP IN 2)

* When both of the DP IN 1 and DP IN 2 connectors are connected

to graphics cards, you can choose two of the HDMI connector,

Thunderbolt

™

3 connector 1, and Thunderbolt

™

3 connector 2 to

use.

 1 x 5-pin J1 header, connecting to the motherboard THB_C header

by the included THB_C header cable

Interface  PCIe 3.0 interface (PCIe x4)

Data Transfer

Rate  40 Gbps Bi-directional per port

Supported

Operating Systems

Support for Windows 10/8.1 (64-bit)/Windows 7 (32-bit/64-bit)

Compatible

Motherboards 

Go to GIGABYTE’s website for the latest motherboard support list.

Product Specication

- 3 -

Installing the GIGABYTE GC-ALPINE RIDGE Add-in Card

GC-ALPINE RIDGE Add-in Card

J1 Header

THB_C Header Cable x 1Mini-DisplayPort Cable x 2

PCIe x4 Interface

Thunderbolt™ 3 Port 1

Thunderbolt™ 3 Port 2

Mini-DisplayPort In Port 1 (DP IN 1)

Mini-DisplayPort In Port 2 (DP IN 2)

HDMI Port (HDMI)

- 4 -

Step 1:

Install the GC-ALPINE RIDGE add-in card in the

PCIEX4 slot.

Step 3:

Connect the other end of the cable to the THB_C(Note)

header on the motherboard.

Step 2:

Connect one end of the THB_C header cable to the J1

header on the GC-ALPINE RIDGE add-in card.

- 5 -

Step 4:

Follow the steps below to use the included Mini-

DisplayPort cable to connect your graphics card to the

GC-ALPINE RIDGE add-in card.

4-1: Connect the cable from the DisplayPort In

connector on the GC-ALPINE RIDGE add-in card to

the DisplayPort on your graphics card.

4-2: Connect the Thunderbolt™ device’s or DisplayPort/

HDMI monitor’s cable to the Thunderbolt™ 3 connector

on the GC-ALPINE RIDGE add-in card.

•When connecting DisplayPort/HDMI monitor(s), if you connect the Mini-

DisplayPort cable to the DP IN 1 connector, you must connect the monitor’s

cable to the HDMI connector or Thunderbolt™ 3 connector 1. If you connect

the cable to the DP IN 2 connector, you must connect the monitor’s cable to

Thunderbolt 3 connector 2. When both of the DP IN 1 and DP IN 2 connectors

are connected, you can choose two of the HDMI connector, Thunderbolt™ 3

connector 1, and Thunderbolt™ 3 connector 2 to use.

•Make sure to update the motherboard BIOS to the latest version.

4-2

4-1

(Note) The THB_C header cable provided has two

connectors. Choose the correct connector

according to the THB_C header on your

motherboard.

- 6 -

Six Thunderbolt™ devices

Six Thunderbolt™ devices and one native DisplayPort monitor

(A graphics card with DisplayPort is required)

Six Thunderbolt™ devices and three DisplayPort 1.2 monitors

(A graphics card with DisplayPort 1.2 support is required)

Daisy-chaining Thunderbolt™ Enabled Devices

Refer to the following for connecting Thunderbolt™-enabled devices in a daisy-chaining

conguration. The following are single-port congurations. (Make sure the Thunderbolt™-enabled

devices to be daisy-chained have both Thunderbolt™ in and out ports.)

- 7 -

Installing the Driver

After the computer starts, install the driver for the GC-ALPINE RIDGE add-in card. Insert the

included driver disk and follow the on-screen instructions to install the driver.

Please visit GIGABYTE’s global website (http://www.gigabyte.com) and click on

Support & Downloads for the latest software driver.

- 8 -

Intel® DSL6540 Thunderbolt™ 3

 2 Thunderbolt

™

3 (Thunderbolt

™

3 1/Thunderbolt

™

2) 40 Gbps

4096x2304@60 Hz

1H DMI 4096x2160@24 Hz

* HDMI 1.4

 2M ini-DisplayPort (DP IN 1/DP IN 2)

* DP IN 1/DP IN 2 HDMI

Thunderbolt™ 3 1 Thunderbolt™ 3 2

 1 5-pin J1 THB_C

THB_C

 PCIe 3.0 (PCIe x4)

40 Gbps

Windows 10/8.1(64-bit)/Windows 7(32-bit/64-bit)



- 9 -

GC-ALPINE RIDGE

THB_C-1Mini-DisplayPort-2

GC-ALPINE RIDGE

PCIe x4

Thunderbolt™ 31

Thunderbolt™ 32

Mini-DisplayPort In1 (DP IN 1)

Mini-DisplayPort In2 (DP IN 2)

HDMI (HDMI)

- 10 -

GC-ALPINE RIDGE PCIEX4

THB_C ( )

THB_C

THB_C GC-ALPINE

RIDGEJ1

- 11 -

Mini-DisplayPort

GC-ALPINE RIDGE

4-1 GC-ALPINE RIDGE Mini-DisplayPort In

DisplayPort

4-2 GC-ALPINE RIDGE Thunderbolt™ 3

Thunderbolt™DisplayPort/

HDMI

•DisplayPort HDMI DP IN 1

HDMI Thunderbolt

™

3 1

DP IN 2Thunderbolt

™

DP IN 1 DP IN 2 HDMI Thunderbolt

™

1Thunderbolt

™

32()

•BIOS

() THB_C

THB_C

4-2

4-1

- 12 -

6Thunderbolt™

6Thunderbolt™1DisplayPort

(DisplayPort)

6Thunderbolt™3DisplayPort 1.2

(DisplayPort 1.2)

Thunderbolt™

( Thunderbolt™

)

- 13 -

GC-ALPINE RIDGE

(http://www.gigabyte.tw)

- 14 -

FCC Notice (U.S.A. Only)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult a dealer or experienced TV/radio technician for help.

Canada, Industry Canada (IC) Notices / Canada, avis d'Industry Canada (IC)

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003

et RSS-210.

Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit

pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment

les interférences qui peuvent affecter son fonctionnement.

Jul. 29, 2016

PCIe add in card

GC-ALPINE RIDGE

PCIe add-in card

GC-ALPINE RIDGE

Jul. 29, 2016

Gigabyte GC-ALPINE RIDGE 取扱説明書

関連論文

その他の書類