Gigabyte GC-TITAN RIDGE 取扱説明書

タイプ
取扱説明書
GC-TITAN RIDGE
Installation Guide// 安装指南
12WE6-TITANR-00AR
For more product details, please visit GIGABYTE's website.
- 2 -
Chip Intel® DSL7540 Thunderbolt 3 Controller
Back Panel
Connectors
1 x DisplayPort In port, supporting a maximum resolution of
8K
(7680x3840)@60 Hz
(Note 1) (Note 2)
* Support for DisplayPort 1.4 version, HDCP 2.2, and HDR.
2 x Thunderbolt
3 out ports (Thunderbolt
3 Port 1/Thunderbolt
3 Port 2), supporting up to 40 Gbps bandwidth and a maximum
display resolution of 8K (7680x3840)@60 Hz
(Note 1) (Note 2)
2 x Mini-DisplayPort In ports (DP_IN1/DP_IN2)
Internal
Connectors
2 x 6-pin PCIe power connectors
1 x USB 2.0/1.1 header
1 x 5-pin J1 header, connecting to the motherboard THB_C header
by the included THB_C header cable
Interface PCIe 3.0 interface (PCIe x4)
Data Transfer
Rate 40 Gbps Bi-directional per port
Supported
Operating Systems
Support for Windows 10 (64-bit) with RS3 or later
Compatible
Motherboards
Go to GIGABYTE’s website for the latest motherboard support list.
Product Specication
(Note 1) Actual resolutions supported are dependent on the graphics card being used.
(Note 2) Due to hardware limitations, the DisplayPort connector, Thunderbolt 3 connector 1, and
Thunderbolt 3 connector 2 require signal input from external devices and support up to
two display outputs at a time.
- 3 -
Intel® DSL7540 Thunderbolt 3
1 DisplayPort 8K(7680 x 3840)@60 Hz
( )( )
* DisplayPort 1.4 HDCP 2.2 HDR
2 Thunderbolt 3 (Thunderbolt 3 1/Thunder-
bolt 3 2) 40 Gbps
8K(7680 x 3840)@60 Hz
( )( )
2M ini-DisplayPort (DP_IN1/DP_IN2)
2 6-pin PCIe
1 USB 2.0/1.1
1 5-pin J1 THB_C
THB_C
PCIe 3.0 (PCIe x4)
40 Gbps
Windows 10 (64-bit) RS3()
()
( ) DisplayPort Thunderbolt 3 1 Thunderbolt 3 2
- 4 -
Intel® DSL7540 Thunderbolt 3 制器
后方面板设
备连接插座
1DisplayPort输出支持至最8K(7680 x 3840)@60 Hz
的分辨率
(注一)(注二)
*
支持DisplayPort 1.4HDCP 2.2HDR
2Thunderbolt 3出插(Thunderbolt 31/Thunder-
bolt 3插座2)最高可支持40 Gbps传输速度幕可支
至最8K(7680 x 3840)@60 Hz的分辨率(注一)(注二)
2Mini-DisplayPort输入插(DP_IN1/DP_IN2)
内接插座 26-pin PCIe电源插
1USB 2.0插座
15-pin J1插座经由附件的THB_C插座连接线与
板的THB_C插座连接
界面 PCIe 3.0 界面(PCIe x4)
数据传输速度 每个接口可支持至最高40 Gbps双向传输速度
支持操作系统 支持Windows 10 (64-bit) RS3()以上版本
可兼容主板 至技嘉网站查询有关支持的主板列表
产品规格
(注一) 实际所支持的分辨率会依您所使用的卡而有不同
() 由于硬件限制DisplayPort插座Thunderbolt 3插座1Thunderbolt 3插座2 需要
外部输入信且同时只支持两个显示输出
- 5 -
J1 Header
J1
J1插座
THB_C Header Cable x 1
THB_C-1
THB_C插座连接线-1
Mini-DisplayPort Cable x 2
Mini-DisplayPort-2
Mini-DisplayPort连接线-2
PCIe x4 Interface
PCIe x4
PCIe x4 界面
Thunderbolt 3 Port 1
Thunderbolt 31
Thunderbolt 3插座1
Thunderbolt 3 Port 2
Thunderbolt 32
Thunderbolt 3插座2
Mini-DisplayPort In Port 2 (DP IN 2)
Mini-DisplayPort In2 (DP IN 2)
Mini-DisplayPort In插座2 (DP IN 2)
Mini-DisplayPort In Port 1 (DP IN 1)
Mini-DisplayPort In1 (DP IN 1)
Mini-DisplayPort In插座1 (DP IN 1)
DisplayPort
DisplayPort
DisplayPort插座 PCIe Power Connector
PCIe
PCIe电源插座
USB Connector
USB
USB接口插座
USB 2.0/1.1 Header Cable x 1
USB 2.0/1.1-1
USB 2.0插座连接线-1
Installing the GC-TITAN RIDGE Add-in CardGC-TIT AN RIDGE
安装GC-TITAN RIDGE
- 6 -
Step 1:
Install the GC-TITAN RIDGE add-in card in the PCIEX4 slot.
1
GC-TIT AN RIDGE PCIEX4
步骤1
GC-TITAN RIDGE卡安装至PCIEX4插槽。
Step 3:
Connect the other end of the cable to the THB_C(Note) header
on the motherboard.
3
THB_C ( )
THB_C
步骤3
THB_C插座连接线的另一端()连接至主板上的
THB_C插座。
Step 2:
Connect one end of the THB_C header cable to the J1
header on the GC-TITAN RIDGE add-in card.
2
THB_C GC-TITAN RIDGE
J1
步骤2
THB_C插座连接线的一端连接至GC-TITAN RIDGE
卡上的J1插座。
- 7 -
(Note) The THB_C header cable provided has two
connectors. Choose the correct connector according
to the THB_C header on your motherboard.
() THB_C
THB_C
() 随货附赠的THB_C插座连接线提供两种接
头,请依主板上的THB_C插座选择接头类
型。
Step 4:
Connect one end of the USB cable to the USB connector on
the GC-TITAN RIDGE card.
4
USB GC-TITAN RIDGE USB
步骤4
USB扁平电缆的一端接至GC-TITAN RIDGE卡的
USB接口插座。
Step 5:
Connect the other end of the USB cable to the F_USB
connector on the motherboard.
5
USB F_USB
步骤5
再将USB扁平电缆的另一端接至主板的F_USB
插座。
- 8 -
Step 7:
Follow the steps below to use the included Mini-
DisplayPort cable to connect your graphics card to the
GC-TITAN RIDGE add-in card.
7-1: Connect the cable from the DisplayPort In connector on
the GC-TITAN RIDGE add-in card to the DisplayPort
on your graphics card.
7-2: Connect the Thunderbolt device’s or DisplayPort
monitor’s cable to the Thunderbolt 3 connector on
the GC-TITAN RIDGE add-in card.
7-2
7-1
Step 6:
Connect the power cables from the power supply to the
two PCIe connectors.
6
PCIe
步骤6
将电源供应器上的电源接头连接至两组PCIe
源插座。
7
Mini-DisplayPort GC-TITAN RIDGE
7-1GC-TIT AN RIDGEMini-DisplayPort InDisplayPort
7-2 GC-TITAN RIDGEThunderbolt 3Thunderbolt DisplayPort
- 9 -
When connecting DisplayPort monitor, if you connect the Mini-DisplayPort cable to the
DP IN 1 connector, you must connect the monitor’s cable to the DisplayPort connector or
Thunderbolt 3 connector 1. If you connect the cable to the DP IN 2 connector, you must
connect the monitor’s cable to Thunderbolt 3 connector 2.
DisplayPortDP IN 1
DisplayPortThunderbolt 31DP IN 2
Thunderbolt 32
连接DisplayPort显示器时,如果您是将连接线连接至DP IN 1插座,您就必须将
显示器连接线接至DisplayPortThunderbolt™ 3插座1;若是连接至DP IN 2就必
须将显示器连接线接至Thunderbolt™ 3插座2
Make sure to update the motherboard BIOS to the latest version.
BIOS
请确认您主板的BIOS为最新版本。
步骤7
请依照下列步骤使用所附的Mini-DisplayPort连接线将您的显卡与GC-TITAN RIDGE卡做
连接
7-1GC-TITAN RIDGE上的Mini-DisplayPort In插座需链接至显卡的DisplayPort
7-2 GC-TITAN RIDGE上的Thunderbolt 3插座则需链接至Thunderbolt备或DisplayPort
屏幕。
- 10 -
Six Thunderbolt devices
6Thunderbolt
6Thunderbolt设备
Six Thunderboltdevices and one native DisplayPort monitor
(A graphics card with DisplayPort is required)
6Thunderbolt1DisplayPort
(DisplayPort)
6Thunderbolt设备及1台原生DisplayPort屏幕
(需搭配支持DisplayPort的显卡)
Daisy-chaining Thunderbolt Enabled DevicesThunderbolt
串接Thunderbolt
Refer to the following for connecting Thunderbolt-enabled devices in a daisy-chaining conguration. The
following are single-port congurations. (Make sure the Thunderbolt-enabled devices to be daisy-chained
have both Thunderbolt in and out ports.)
Thunderbolt
(Thunderbolt )
若要以菊链式串接方式串Thunderbolt设备,请参考下列说明。以下为单一接口的串
接示意图。(请先确认要串接的设备皆具备Thunderbolt输出及输入插座。)
- 11 -
Installing the Driver• •安装驱动程序
After the computer starts, install the driver for the GC-TITAN RIDGE add-in card. Insert the
included driver disk and follow the on-screen instructions to install the driver.
GC-TITAN RIDGE
电脑重新启动后,请安装GC-TITAN RIDGE的驱动程序。将所附的驱动程序光盘
插入并且依屏幕指示完成驱动程序的安装。
Please visit GIGABYTE’s global website (http://www.gigabyte.com) and click on
Support & Downloads for the latest software driver.
(http://www.gigabyte.tw)
请至技嘉网站(http://www.gigabyte.com)点选「支持与下载」查询最新版的驱动程序。
Six Thunderboltdevices and three DisplayPort 1.2 monitors
(A graphics card with DisplayPort 1.2 support is required)
6Thunderbolt3DisplayPort 1.2
(DisplayPort 1.2)
6Thunderbolt设备及3DisplayPort 1.2规格屏幕
(需搭配支持DisplayPort 1.2规格的显卡)
FCC Notice (U.S.A. Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult a dealer or experienced TV/radio technician for help.
Canada, Industry Canada (IC) Notices / Canada, avis d'Industry Canada (IC)
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003
et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit
pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment
les interférences qui peuvent affecter son fonctionnement.
Jun. 6, 2018
PCIe add in card
GC-TITAN RIDGE
PCIe add-in card
GC-TITAN RIDGE
Jun. 6, 2018
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Gigabyte GC-TITAN RIDGE 取扱説明書

タイプ
取扱説明書

他の言語で