GC-TITAN RIDGE 2.0
Installation Guide// 安装指南
12WE6-TITAR2-01AR
For more product details, please visit GIGABYTE's website.
GIGABYTE will reduce paper use in order to fulll the responsibilities of a global citizen.
Also, to reduce the impacts on global warming, the packaging materials of this product are
recyclable and reusable. GIGABYTE works with you to protect the environment.
- 2 -
Chip Intel® DSL7540 Thunderbolt™ 3 Controller
Back Panel
Connectors
1 x DisplayPort, supporting a maximum resolution of 8K
(7680x3840)@60 Hz (Note 1) (Note 2)
* Support for DisplayPort 1.4 version, HDCP 2.2, and HDR.
2 x Thunderbolt
™
3 out ports (Thunderbolt
™
3 Port 1/Thunderbolt
™
3 Port 2), supporting up to 40 Gbps bandwidth and a maximum
display resolution of 8K (7680x3840)@60 Hz
(Note 1) (Note 2)
2 x Mini-DisplayPort In ports (DP_IN1/DP_IN2)
Internal
Connectors
2 x 6-pin PCIe power connectors
1 x USB 2.0/1.1 header
1 x 5-pin Thunderbolt™ header
1 x 3-pin Thunderbolt™ header
Interface PCIe 3.0 interface (PCIe x4)
Data Transfer
Rate 40 Gbps Bi-directional per port
Supported
Operating Systems
Support for Windows 10 (64-bit) with RS3 or later
Compatible
Motherboards
Go to GIGABYTE’s website for the latest motherboard support list.
Product Specication
(Note 1) Actual resolutions supported are dependent on the graphics card being used.
(Note 2) Due to hardware limitations, the DisplayPort connector, Thunderbolt™ 3 connector 1, and
Thunderbolt™ 3 connector 2 require signal input from external devices and support up to
two display outputs at a time.
- 3 -
Intel® DSL7540 Thunderbolt™ 3
1 DisplayPort 8K(7680 x 3840)@60 Hz
()()
* DisplayPort 1.4 HDCP 2.2 HDR
2 Thunderbolt™ 3 (Thunderbolt™ 3 1/Thunder-
bolt™ 3 2)40 Gbps
8K(7680 x 3840)@60 Hz
()()
2M ini-DisplayPort (DP_IN1/DP_IN2)
2 6-pin PCIe
1 USB 2.0/1.1
1 5-pin Thunderbolt™
1 3-pin Thunderbolt™
PCIe 3.0 (PCIe x4)
40 Gbps
Windows 10 (64-bit) RS3()
()
() DisplayPort Thunderbolt™ 3 1 Thunderbolt™ 3 2
- 4 -
芯片 Intel® DSL7540 Thunderbolt™ 3 控制器
后方面板设
备连接插座
1个DisplayPort输出插座，可支持至最高8K(7680 x 3840)@60 Hz的
分辨率
(注一)(注二)
*
支持DisplayPort 1.4版本、HDCP 2.2及HDR。
2个Thunderbolt™ 3输出插座(Thunderbolt™ 3插座1/Thunderbolt™
3插座2)，最高可支持40 Gbps传输速度，屏幕可支持至最高
8K(7680 x 3840)@60 Hz的分辨率(注一)(注二)
2个Mini-DisplayPort输入插座(DP_IN1/DP_IN2)
内接插座 2个6-pin PCIe电源插座
1个USB 2.0插座
1个5-pin Thunderbolt™ 插座
1个3-pin Thunderbolt™ 插座
界面 PCIe 3.0 界面(PCIe x4)
数据传输速度 每个接口可支持至最高40 Gbps双向传输速度
支持操作系统 支持Windows 10 (64-bit) RS3(含)以上版本
可兼容主板 请至技嘉网站查询有关支持的主板列表
产品规格
(注一) 实际所支持的分辨率会依您所使用的显卡而有不同。
(注二) 由于硬件限制，DisplayPort插座、Thunderbolt™ 3插座1和Thunderbolt™ 3插座2 需要外部输
入信号，并且同时只支持两个显示输出。
- 5 -
5-pin Thunderbolt™ header
5-pin Thunderbolt™
5-pin Thunderbolt™ 插座
PCIe x4 Interface
PCIe x4
PCIe x4 界面
Thunderbolt™ 3 Port 1
Thunderbolt™ 31
Thunderbolt™ 3插座1
Thunderbolt™ 3 Port 2
Thunderbolt™ 32
Thunderbolt™ 3插座2
Mini-DisplayPort In Port 2 (DP IN 2)
Mini-DisplayPort In2 (DP IN 2)
Mini-DisplayPort In插座2 (DP IN 2)
Mini-DisplayPort In Port 1 (DP IN 1)
Mini-DisplayPort In1 (DP IN 1)
Mini-DisplayPort In插座1 (DP IN 1)
DisplayPort
DisplayPort
DisplayPort插座
PCIe Power Connector
PCIe
PCIe电源插座
USB Connector
USB
USB接口插座
Installing the GC-TITAN RIDGE 2.0 Add-in Card
GC-TIT AN RIDGE 2.0 • 安装GC-TITAN RIDGE 2.0卡
3-pin Thunderbolt™ header
3-pin Thunderbolt™
3-pin Thunderbolt™ 插座
- 6 -
Thunderbolt™ Header Cable (5-pin) x 1
Thunderbolt™ (5-pin)-1
Thunderbolt™ 插座连接线 (5-pin)-1条
Mini-DisplayPort Cable x 2
Mini-DisplayPort-2
Mini-DisplayPort连接线-2条
USB 2.0/1.1 Header Cable x 1
USB 2.0/1.1-1
USB 2.0插座连接线-1条
Thunderbolt™ Header Cable (3-pin) x 1
Thunderbolt™ (3-pin)-1
Thunderbolt™ 插座连接线 (3-pin)-1条
- 7 -
Step 1:
Install the GC-TITAN RIDGE 2.0 add-in card in the PCIEX4 slot.
1
GC-TIT AN RIDGE 2.0 PCIEX4
步骤1：
将GC-TITAN RIDGE 2.0卡安装至PCIEX4插槽。
Step 2:
Connect one end of the USB cable to the USB connector on the
GC-TITAN RIDGE 2.0 card.
2
USB GC-TITAN RIDGE 2.0 USB
步骤2：
将USB扁平电缆的一端接至GC-TITAN RIDGE 2.0卡的USB
接口插座。
Step 3:
Connect the other end of the USB cable to the F_USB connector
on the motherboard.
3
USBF_USB
步骤3：
再将USB扁平电缆的另一端接至主板的F_USB插座。
- 8 -
(Note 1) The Thunderbolt™ header cable (5-pin) provided
has two connectors. Choose the correct connector
according to the Thunderbolt™ add-in card header on
your motherboard.
() Thunderbolt ™ (5-pin)
Thunderbolt™
(注一) 随货附赠的Thunderbolt™插座连接线 (5-pin)提供两种
接口，请依主板上的Thunderbolt™扩展子卡插座选择
接口类型。
Step 5:
Connect the other end of the cable to the Thunderbolt™ add-in
card header (Note 1) on the motherboard.
5
Thunderbolt™
()
步骤5：
将另一端连接至主板上的Thunderbolt™扩展子卡插座(注一)。
Step 4:
Connect one end of the Thunderbolt™ header cable (5-pin) to
the 5-pin Thunderbolt™ header on the GC-TITAN RIDGE 2.0
add-in card.
4
Thunderbolt™ (5-pin)GC-TITAN
RIDGE 2.05-pin Thunderbolt™
步骤4：
将Thunderbolt™ 插座连接线 (5-pin)的一端连接至GC-TITAN
RIDGE 2.0卡上的5-pin Thunderbolt™插座。
- 9 -
(Note 2) Whether the connector is supported depends on the motherboard models.
()
(注二) 是否支持此插座依据主板而定。
Step 7:
Connect the other end of the cable to the Thunderbolt™ add-in
card header (Note 2) on the motherboard.
7
Thunderbolt™
()
步骤7：
将另一端连接至主板上的Thunderbolt™扩展子卡插座(注二)。
Step 6:
Connect one end of the Thunderbolt™ header cable (3-pin) to
the 3-pin Thunderbolt™ header on the GC-TITAN RIDGE 2.0
add-in card.
6
Thunderbolt™ (3-pin)GC-TITAN
RIDGE 2.03-pin Thunderbolt™
步骤6：
将Thunderbolt™插座连接线 (3-pin)的一端连接至GC-TITAN
RIDGE 2.0卡上的3-pin Thunderbolt™插座。
- 10 -
Step 9:
Follow the steps below to use the included Mini-
DisplayPort cable to connect your graphics card to the
GC-TITAN RIDGE 2.0 add-in card.
9-1: Connect the cable from the DisplayPort In connector
on the GC-TITAN RIDGE 2.0 add-in card to the
DisplayPort on your graphics card.
9-2: Connect the Thunderbolt™ device’s or DisplayPort
monitor’s cable to the Thunderbolt™ 3 connector on
the GC-TITAN RIDGE 2.0 add-in card.
9-2
9-1
Step 8:
Connect the power cables from the power supply to the
two PCIe connectors.
8
PCIe
步骤8：
将电源供应器上的电源接头连接至两组PCIe电源
插座。
9
Mini-DisplayPort GC-TITAN RIDGE 2.0
9-1GC-TIT AN RIDGE 2.0Mini-DisplayPort InDisplayPort
9-2 GC-TITAN RIDGE 2.0 Thunderbolt™ 3 Thunderbolt™
DisplayPort
- 11 -
•When connecting one DisplayPort monitor, please connect the Mini-DisplayPort cable to
the DP IN 1 connector, then connect the monitor’s cable to the DisplayPort connector or
Thunderbolt™ 3 connector 1.
•When connecting two DisplayPort monitors, please connect one of the Mini-DisplayPort
cables to the DP IN 1 connector and connect the monitor’s cable to the DisplayPort connector
or Thunderbolt™ 3 connector 1. Then connect the other Mini-DisplayPort cable to the DP
IN 2 connector and the monitor’s cable to Thunderbolt™ 3 connector 2.
•DisplayPort Mini-DisplayPort DP IN 1
DisplayPortThunderbolt ™ 31
•DisplayPort Mini-DisplayPort DP IN 1
DisplayPort Thunderbolt™ 3 1 Mini-DisplayPort
DP IN 2Thunderbolt ™ 32
•连接一台DP显示器时，请将Mini-DP连接线连接至DP IN 1接口，并将显示器连接线连
接至DP或Thunderbolt
™
3接口1。
•连接两台DP显示器时，请将Mini-DP连接线连接至DP IN 1接口，并将显示器连接线接
至DP或Thunderbolt
™
3接口1；Mini-DP连接线连接至DP IN 2接口，并将显示器连接线接
至Thunderbolt
™
3接口2。
•Make sure to update the motherboard BIOS to the latest version.
•BIOS
•请确认您主板的BIOS为最新版本。
步骤9：
请依照下列步骤使用所附的Mini-DisplayPort连接线将您的显卡与GC-TITAN RIDGE 2.0卡做连接。
9-1：GC-TITAN RIDGE 2.0卡上的Mini-DisplayPort In插座需链接至显卡的DisplayPort。
9-2： GC-TITAN RIDGE 2.0卡上的Thunderbolt™ 3插座则需链接至Thunderbolt™设备或DisplayPort
屏幕。
- 12 -
Six Thunderbolt™ devices
6Thunderbolt™
6台Thunderbolt™设备
Six Thunderbolt™ devices and one native DisplayPort monitor
(A graphics card with DisplayPort is required)
6Thunderbolt™1DisplayPort
(DisplayPort)
6台Thunderbolt™设备及1台原生DisplayPort屏幕
(需搭配支持DisplayPort的显卡)
Daisy-chaining Thunderbolt™ Enabled Devices•Thunderbolt™ •
串接Thunderbolt™
Refer to the following for connecting Thunderbolt™-enabled devices in a daisy-chaining conguration. The
following are single-port congurations. (Make sure the Thunderbolt™-enabled devices to be daisy-chained
have both Thunderbolt™ in and out ports.)
Thunderbolt™
(Thunderbolt ™)
若要以菊链式串接方式串连Thunderbolt™设备，请参考下列说明。以下为单一接口的串接示
意图。(请先确认要串接的设备皆具备Thunderbolt™输出及输入插座。)
- 13 -
Installing the Driver• •安装驱动程序
After the computer starts, install the driver for the GC-TITAN RIDGE 2.0 add-in card. Insert the
included driver disc and follow the on-screen instructions to install the driver.
GC-TIT AN RIDGE 2.0
电脑重新启动后，请安装GC-TITAN RIDGE 2.0的驱动程序。将所附的驱动程序光盘插
入并且依屏幕指示完成驱动程序的安装。
Please visit GIGABYTE’s global website (http://www.gigabyte.com) and click on
Support & Downloads for the latest software driver.
(http://www.gigabyte.tw)
请至技嘉网站(http://www.gigabyte.com)点选「支持与下载」查询最新版的驱动程序。
Six Thunderbolt™ devices and three DisplayPort monitors
(A graphics card with DisplayPort support is required)
6Thunderbolt™3DisplayPort
(DisplayPort )
6台Thunderbolt™设备及3台DisplayPort规格屏幕
(需搭配支持DisplayPort规格的显卡)
Regulatory Notices
United States of America, Federal Communications Commission Statement
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: PCIe add in card
Trade Name: GIGABYTE
Model Number: GC-TITAN RIDGE 2.0
Responsible Party – U.S. Contact Information: G.B.T. Inc.
Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian
ICES-003.
Avis de conformité à la réglementation d'Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
European Union (EU) CE Declaration of Conformity
This device complies with the following directives: Electromagnetic Compatibility Directive 2014/30/EU, Low-voltage Directive
2014/35/EU, RoHS directive (recast) 2011/65/EU & the 2015/863 Statement. This product has been tested and found to comply
with all essential requirements of the Directives.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the European Commission Delegated Directive (EU) 2015/863
Statement
GIGABYTE products have not intended to add and safe from hazardous substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP,
DBP and DIBP). The parts and components have been carefully selected to meet RoHS requirement. Moreover, we at GIGABYTE
are continuing our efforts to develop products that do not use internationally banned toxic chemicals.
European Union (EU) Community Waste Electrical & Electronic Equipment (WEEE) Directive Statement
GIGABYTE will fulll the national laws as interpreted from the 2012/19/EU WEEE (Waste Electrical and Electronic Equipment) (recast)
directive. The WEEE Directive species the treatment, collection, recycling and disposal of electric and electronic devices and their
components. Under the Directive, used equipment must be marked, collected separately, and disposed of properly.
WEEE Symbol Statement
The symbol shown below is on the product or on its packaging, which indicates that this product must not be
disposed of with other waste. Instead, the device should be taken to the waste collection centers for activation of the
treatment, collection, recycling and disposal procedure.
For more information about where you can drop off your waste equipment for recycling, please contact your local
government office, your household waste disposal service or where you purchased the product for details of
environmentally safe recycling.
End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, which indicates that this product must not be disposed
of with other waste. Instead, the device should be taken to the waste collection centers for activation of the treatment,
collection, recycling and disposal procedure.
Déclaration de Conformité aux Directives de l'Union européenne (UE)
Cet appareil portant la marque CE est conforme aux directives de l'UE suivantes: directive Compatibilité Electromagnétique
2014/30/UE, directive Basse Tension 2014/35/UE et directive RoHS II 2011/65/UE. La conformité à ces directives est évaluée sur la
base des normes européennes harmonisées applicables.
European Union (EU) CE-Konformitätserklärung
Dieses Produkte mit CE-Kennzeichnung erfüllen folgenden EU-Richtlinien: EMV-Richtlinie 2014/30/EU, Niederspannungsrichtlinie
2014/30/EU und RoHS-Richtlinie 2011/65/EU erfüllt. Die Konformität mit diesen Richtlinien wird unter Verwendung der
entsprechenden Standards zurEuropäischen Normierung beurteilt.
CE declaração de conformidade
Este produto com a marcação CE estão em conformidade com das seguintes Diretivas UE: Diretiva Baixa Tensão 2014/35/
EU; Diretiva CEM 2014/30/EU; Diretiva RSP 2011/65/UE. A conformidade com estas diretivas é vericada utilizando as normas
europeias harmonizadas.
CE Declaración de conformidad
Este producto que llevan la marca CE cumplen con las siguientes Directivas de la Unión Europea: Directiva EMC (2014/30/
EU), Directiva de bajo voltaje (2014/35/EU), Directiva RoHS (recast) (2011/65/EU). El cumplimiento de estas directivas se evalúa
mediante las normas europeas armonizadas.
Dichiarazione di conformità CE
Questo prodotto è conforme alle seguenti direttive: Direttiva sulla compatibilità elettromagnetica 2014/30/UE, Direttiva sulla bassa
tensione 2014/35/UE, Direttiva RoHS (rifusione) 2011/65/UE. Questo prodotto è stato testato e trovato conforme a tutti i requisiti
essenziali delle Direttive.
D33006
RoHS
BSMI CNS15663
Declaration of the Presence Condition of the Restricted Substances Marking
PCIe add in card GC-TITAN RIDGE 2.0
Equipment name Type designation (Type)
Unit
Restricted substances and its chemical symbols
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr
+6
)
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
PCB
Shell
Chip and other Active
components
Passive Components
Connectors
Soldering metal
Cables
1. " 0.1 wt %" " 0.01 wt %"
Note 1: "Exceeding 0.1 wt %" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance
exceeds the reference percentage value of presence condition.
2. " "
Note 2: " " indicates that the percentage content of the restricted substance does not exceed the percentage of reference
value of presence.
3. " "
Note 3: The " " indicates that the restricted substance corresponds to the exemption.
关于符合中国《电器电子产品有害物质限制使用管理办法》的声明
Administrative Measures for the Restricted Use of Hazardous Substances in Electrical and Electronic Products
(China RoHS Declaration)
产品中有害物质的名称及含量
Hazardous Substances Table
部件名称(Parts)
有害物质(Hazardous Substances)
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
印刷电路板
PCB ○ ○ ○ ○ ○ ○
外壳
Shell ○ ○ ○ ○ ○ ○
芯片及其他主动零件
Chip and other Active
components
× ○ ○ ○ ○ ○
被动电子元器件
Passive Components
× ○ ○ ○ ○ ○
连接器
Connectors
× ○ ○ ○ ○ ○
焊接金属
Soldering metal
○ ○ ○ ○ ○ ○
线材
Cables
○ ○ ○ ○ ○ ○
These tables are prepared in accordance with the provisions of SJT 11364
本表格依据SJ/T 11364 的规定编制。
○： The content of such hazardous substance in all homogeneous materials of such component is below the limit
required by GB/T 26572.
表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
×： The content of such hazardous substance in a certain homogeneous material of such component is beyond the limit
required by GB/T 26572.
表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求。
Contact Us
GIGA-BYTE TECHNOLOGY CO., LTD.
Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231
TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : https://esupport.gigabyte.com
WEB address (English): https://www.gigabyte.com
WEB address (Chinese): https://www.gigabyte.com/tw
Copyright
© 2023 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specications and features in this manual may be made by GIGABYTE without prior notice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means
without GIGABYTE's prior written permission.
For product-related information, check on our website at: https://www.gigabyte.com
/