DeWalt DCS570 ユーザーマニュアル

ブランド: DeWalt

モデル: DCS570

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

DCS570

English 5

繁體中文

한국어 29

1 2

1211

957

Fig. A

圖 A

그림 A

Fig. C

圖 C

그림 C

Fig. B

圖 B

그림 B

Fig. E

圖 E

그림 E

Fig. G

圖 G

그림 G

Fig. D

圖 D

그림 D

Fig. F

圖 F

그림 F

Fig. I

圖 I

그림 I

Fig. H

圖 H

그림 H

Fig. K

圖 K

그림 K

Fig. J

圖 J

그림 J

Fig. M

圖 M

그림 M

Fig. L

圖 L

그림 L

Fig. O

圖 O

그림 O

Fig. N

圖 N

그림 N

Fig. Q

圖 Q

그림 Q

Fig. P

圖 P

그림 P

ENGLISH



Denotes risk of electricshock.



Denotes risk offire.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

Congratulations!

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the

most reliable partners for professional power toolusers.

Technical Data

DCS570

Voltage V

Type 1

Battery type Li-Ion

No-load speed min

-1

5500

Blade diameter mm

184

Maximum depth of cut mm

Blade bore mm

Bevel angle adjustment °

Weight (without battery pack) kg 3.6

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.

CORDLESS CIRCULAR SAW

DCS570

Batteries Chargers/Charge Times (Minutes)

Cat # V

Weight

DCB107 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 270 140 90 60 90 X

DCB547 18/54 9.0/3.0 1.25 420 220 140 85 140 X

DCB181 18 1.5 0.35 70 35 22 22 22 45

DCB182 18 4.0 0.61 185 100 60 60 60 120

DCB183/B 18 2.0 0.40 90 50 30 30 30 60

DCB184/B 18 5.0 0.62 240 120 75 75 75 150

DCB185 18 1.3 0.35 60 30 22 22 22 X

DCB187 18 3.0 0.48 140 70 45 45 45 90

ENGLISH

Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

Electrical safety

d ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

e ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

f ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

g ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

h ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

i ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

Personal safety

j ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

k ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

l ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

m ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

n ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

o ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

p ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

Power tool use and care

q ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

r ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

s ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

t ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

u ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained powertools.

v ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

w ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

Battery tool use and care

x ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

y ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

z ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Batteries

Chargers/Charge Times (Minutes)

DCS570

Weight

ENGLISH

Shorting the battery terminals together may cause burns

or afire.

aa ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

Service

ab ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

SAFETY INSTRUCTIONS FOR ALL SAWS

Cutting Procedures

a ) DANGER: Keep hands away from cutting area

and the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding the

saw, they cannot be cut by theblade.

b ) Do not reach underneath the workpiece. The guard

cannot protect you from the blade below theworkpiece.

c ) Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below theworkpiece.

d ) Never hold piece being cut in your hands or across

your leg while cutting. Secure the workpiece to a

stable platform. It is important to support the work

properly to minimize body exposure, blade binding, or loss

ofcontrol.

e ) Hold the power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring. Contact with a “live”

wire will also make exposed metal parts of the power tool

“live” and could give the operator an electricshock.

f ) When ripping always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of bladebinding.

g ) Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades that

do not match the mounting hardware of the saw will run

off-centre, causing loss ofcontrol.

h ) Never use damaged or incorrect blade washers or

bolt. The blade washers and bolt were specially designed

for your saw, for optimum performance and safety

ofoperation.

FURTHER SAFETY INSTRUCTIONS FOR ALL

SAWS

Kickback Causes and Related Warnings

• Kickback is a sudden reaction to a pinched, jammed or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator;

• When the blade is pinched or jammed tightly by the kerf

closing down, the blade stalls and the motor reaction drives

the unit rapidly back toward the operator;

• If the blade becomes twisted or misaligned in the cut, the teeth

at the back edge of the blade can dig into the top surface of

the wood causing the blade to climb out of the kerf and jump

back toward theoperator.

Kickback is the result of saw misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

a ) Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions aretaken.

b ) When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to

a complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the

blade is in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause of

bladebinding.

c ) When restarting a saw in the workpiece, centre

the saw blade in the kerf so that the saw teeth are

not engaged into the material. If saw blade binds, it

may walk up or kickback from the workpiece as the saw

isrestarted.

d ) Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed under

the panel on both sides, near the line of cut and near the

edge of thepanel.

e ) Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding andkickback.

f ) Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding

andkickback.

g ) Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can causekickback.

SAFETY INSTRUCTIONS FOR SAWS WITH A

PENDULUM BLADE GUARD

Lower Guard Function

a ) Check the lower guard for proper closing before each

use. Do not operate the saw if the lower guard does

not move freely and close instantly. Never clamp

or tie the lower guard into the open position. If the

saw is accidentally dropped, the lower guard may

be bent. Raise the lower guard with the retracting handle

and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths ofcut.

b ) Check the operation of the lower guard spring. If the

guard and the spring are not operating properly,

they must be serviced before use. Lower guard may

ENGLISH

operate sluggishly due to damaged parts, gummy

deposits, or a build-up ofdebris.

c ) The lower guard should be retracted manually

only for special cuts such as “plunge cuts” and

“compound cuts”. Raise the lower guard by

retracting handle and as soon as blade enters

the material, the lower guard must be released.

For all other sawing, the lower guard should

operateautomatically.

d ) Always observe that the lower guard is covering

the blade before placing the saw down on bench or

floor. An unprotected, coasting blade will cause the

saw to walk backwards, cutting whatever is in its

path. Be aware of the time it takes for the blade to stop

after switch isreleased.

Additional Safety Instructions for Circular

Saws

• Wear ear protectors. Exposure to noise can cause

hearingloss.

• Wear a dust mask. Exposure to dust particles can cause

breathing difficulty and possibleinjury.

• Do not use blades of larger or smaller diameter than

recommended. For the proper blade rating refer to the

Technical Data. Use only the blades specified in this manual,

complying with EN 847-1.

• Never use abrasive cut-offwheels.

• Do not use water feedattachments.

• Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and may

lead to loss ofcontrol.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your DeWALT charger is double insulated in

accordance with IEC60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DeWALT

serviceorganisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

DeWALT chargers require no adjustment and are designed to be

as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DeWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

ENGLISH

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. A)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

3

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

13

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

ENGLISH

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in

DeWALTchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a

DeWALT battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities,

DeWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLT

Battery

The

DeWALT FLEXVOLT

battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLT

battery stands alone or is in

a DeWALT 18V product, it will operate as an 18V battery. When

the FLEXVOLT

battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLT

battery, the battery is in Transport mode. Keep the cap for

shipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

ENGLISH

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

batteries of 36 Wh each.

The Use Wh rating might

indicate 108Wh (1battery implied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose to water.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Example of Use and Transport Label Marking

Charge DeWALT battery packs only with designated

DeWALT chargers. Charging battery packs other

than the designated DeWALT batteries with a

DeWALT charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36 Wh).

Battery Type

The DCS570 operates on a 18 volt batterypack.

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB546,

DCB547. Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Circular saw

1 Circular saw blade

1 Blade wrench

1 Parallel fence

1 Dust extraction port

1 Charger (C, D, L, M, P, S, T, X models)

1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1 models)

2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2 models)

3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3 models)

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Visible radiation. Do not stare intolight.

Date Code Position (Fig. A)

The date code

19

, which also includes the year of manufacture,

is printed into thehousing.

Example:

ENGLISH

2017 XX XX

Year of Manufacture

Description (Fig. A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

Trigger switch lock-off button

Trigger switch

Battery pack

Depth adjustment lever (Fig.E)

Base plate

Lower blade guard retracting lever

Lower blade guard

Blade clamping screw

Kerf indicator

Bevel adjustment lever

Blade lock button

Auxiliary handle

Battery release button

Blade wrench (Fig.E)

Worklight

Rafer Hook

Intended Use

These heavy-duty circular saws are designed for professional

wood cutting applications. Do not cut metal, plastic, concrete,

masonry or fiber cement materials. DO NOT use water feed

attachments with this saw. DO NOT use abrasive wheels or

blades. DO NOT use under wet co0nditions or in the presence

of flammable liquids orgases.

These heavy-duty saws are professional powertools.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only DeWALT battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. A)

NOTE: Make sure your battery pack

3

is fullycharged.

To Install the Battery Pack into the Tool

Handle

1. Align the battery pack

3

with the rails inside the tool’s

handle (Fig. A).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

13

and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. A)

Some DeWALT battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge button

32

. A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Changing Blades

To Install the Blade (Fig.C–E)

1. Remove thebattery.

2. Using the lower guard lever

6

, retract the lower blade

guard

7

and place blade on saw spindle against the inner

clamp washer

17

, making sure that the blade will rotate

in the proper direction (the direction of the rotation arrow

on the saw blade and the teeth must point in the same

direction as the direction of rotation arrow on the saw). Do

not assume that the printing on the blade will always be

facing you when properly installed. When retracting the

lower blade guard to install the blade, check the condition

and operation of the lower blade guard to assure that it is

working properly. Make sure it moves freely and does not

touch the blade or any other part, in all angles and depths

ofcut.

3. Place outer clamp washer

16

on saw spindle with the

beveled edge facing out. Make sure the 30 mm diameter on

the blade side of the clamp fits into the 30 mm hole in the

saw blade to ensure centering of theblade.

4. Thread the blade clamping screw

8

onto the saw spindle

by hand (screw has right-hand threads and must be turned

clockwise to tighten).

5. Depress the blade lock

11

while turning the saw spindle

with the blade wrench

14

stored underneath the battery

compartment, until the blade lock engages and the blade

stopsrotating.

6. Tighten the blade clamping screw firmly with the

bladewrench.

ENGLISH

NOTICE: Never engage the blade lock while saw is

running, or engage in an effort to stop the tool. Never

turn the saw on while the blade lock is engaged. Serious

damage to your saw willresult.

To Replace the blade (Fig.C, D)

1. Remove thebattery.

2. To loosen the blade clamping screw

8

, depress the blade

lock

11

and turn the saw spindle with the blade wrench

14

, stored underneath the battery compartment, until

the blade lock engages and the blade stops rotating.

With the blade lock engaged, turn the blade clamping

screw counterclockwise with the blade wrench (screw has

right-hand threads and must be turned counterclockwise

toloosen).

3. Remove the blade clamping screw

8

and outer clamp

washer

16

. Remove oldblade.

4. Clean any sawdust that may have accumulated in the

guard or clamp washer area and check the condition and

operation of the lower blade guard as previously outlined.

Do not lubricate thisarea.

5. Select the proper blade for the application (refer to Blades).

Always use blades that are the correct size (diameter)

with the proper size and shape center hole for mounting

on the saw spindle. Always assure that the maximum

recommended speed (rpm) on the saw blade meets or

exceeds the speed (rpm) of thesaw.

6. Follow steps 1 through 5 under To Install the Blade, making

sure that the blade will rotate in the properdirection.

Lower Blade Guard



WARNING: The lower blade guard is a safety feature

that reduces the risk of serious personal injury. Never

use the saw if the lower guard is missing, damaged,

misassembled or not working properly. Do not rely

on the lower blade guard to protect you under all

circumstances. Your safety depends on following

all warnings and precautions as well as proper

operation of the saw. Check the lower blade guard

for proper closing before each use. If the lower blade

guard is missing or not working properly, have the

saw serviced before using. To assure product safety

and reliability, repair, maintenance and adjustment

should be performed by an authorized service center

or other qualified service organization, always using

identical replacementparts.

Checking the Lower Guard (Fig.A)

1. Turn tool off and disconnect from powersupply.

2. Rotate the lower guard lever (Fig.A,

6

) from the fully closed

position to the fully openposition.

3. Release the lever and observe the guard

7

return to the

fully closedposition.

The tool should be serviced by a qualified service center if it:

• fails to return to the fully closed position,

• moves intermittently or slowly, or

• contacts the blade or any part of the tool in all angles and

depth ofcut.

Blades



WARNING: To minimize the risk of eye injury, always

use eye protection. Carbide is a hard but brittle material.

Foreign objects in the workpiece such as wire or nails

can cause tips to crack or break. Only operate saw when

proper saw blade guard is in place. Mount blade securely

in proper rotation before using, and always use a clean,

sharpblade.



WARNING: Do not cut metal, plastic, concrete, masonry

or fiber cement materials with thissaw.

184 mm Diameter

Application Teeth

Rip 24

General Purpose 36

Finish 60

If you need assistance regarding blades, please contact your

local

DeWALTdealer.

Kickback

Kickback is a sudden reaction to a pinched, bound or misaligned

saw blade, causing an uncontrolled saw to lift up and out of the

workpiece toward the operator. When the blade is pinched or

bound tightly by the kerf closing down, the blade stalls and the

motor reaction drives the unit rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth

at the back edge of the blade can dig into the top surface of the

wood causing the blade to climb out of the kerf and jump back

toward theoperator.

Kickback is more likely to occur when any of the following

conditionsexists.

1. IMPROPER WORKPIECE SUPPORT

a. Sagging or improper lifting of the cut off piece can cause

pinching of the blade and lead tokickback.

b. Cutting through material supported at the outer ends

only can cause kickback. As the material weakens it sags,

closing down the kerf and pinching the blade (Fig.L).

c. Cutting off a cantilevered or overhanging piece of

material from the bottom up in a vertical direction

can cause kickback. The falling cut off piece can pinch

theblade.

d. Cutting off long narrow strips (as in ripping) can cause

kickback. The cut off strip can sag or twist closing the kerf

and pinching theblade.

e. Snagging the lower guard on a surface below the

material being cut momentarily reduces operator control.

The saw can lift partially out of the cut increasing the

chance of bladetwist.

2. IMPROPER DEPTH OF CUT SETTING ON SAW

a. To make the most efficient cut, the blade should

protrude only far enough to expose one-half of a

tooth as shown in FigureF. This allows the base plate

to support the blade and minimizes twisting and

ENGLISH

pinching in the material. See the section titled Cutting

DepthAdjustment.

3. BLADE TWISTING MISALIGNMENT IN CUT

a. Pushing harder to cut through a knot, a nail or a hard

grain area can cause the blade totwist.

b. Trying to turn the saw in the cut (trying to get back on

the marked line) can cause bladetwist.

c. Overreaching or operating the saw with poor body

control (out of balance), can result in twisting theblade.

d. Changing hand grip or body position while cutting can

result in bladetwist.

e. Backing up the saw to clear blade can lead totwist.

4. MATERIALS THAT REQUIRE EXTRA ATTENTION

a. Wet timber

b. Green timber (material freshly cut or not kiln dried)

c. Pressure treated timber (material treated with

preservatives or anti-rot chemicals)

5. USE OF DULL OR DIRTY BLADES

a. Dull blades cause increased loading of the saw. To

compensate, an operator will usually push harder which

further loads the unit and promotes twisting of the blade

in the kerf. Worn blades may also have insufficient body

clearance which increases the chance of binding and

increasedloading.

6. LIFTING THE SAW WHEN MAKING A BEVEL CUT

a. Bevel cuts require special operator attention to proper

cutting techniques – especially guidance of the saw. Both

blade angle to the base plate and greater blade surface

in the material increase the chance for binding and

misalignment (twist) tooccur.

7. RESTARTING A CUT WITH THE BLADE TEETH JAMMED

AGAINST THE MATERIAL

a. The saw should be brought up to full operating speed

before starting a cut or restarting a cut after the unit has

been stopped with the blade in the kerf. Failure to do so

can cause stalling andkickback.

Any other conditions which could result in pinching, binding,

twisting, or misalignment of the blade could cause kickback.

Refer to the sections Additional Specific Safety Rules for

Circular Saws and Blades for procedures and techniques that

will minimize the occurrence ofkickback.

Depth of Cut Adjustment (Fig.E–F)

1. Raise the depth adjustment lever

4

toloosen.

2. To obtain the correct depth of cut, align the appropriate

mark on the depth adjustment strap

20

with notch

19

the upper bladeguard.

3. Tighten the depth adjustmentlever.

4. For the most efficient cutting action using a carbide tipped

saw blade, set the depth adjustment so that about one half

of a tooth projects below the surface of the wood to becut.

5. A method of checking for the correct cutting depth is

shown in FigureF. Lay a piece of the material you plan to

cut along the side of the blade, as shown in the figure, and

observe how much tooth projects beyond thematerial.

Adjusting Depth Adjustment Lever (Fig.E)

It may be desirable to adjust the depth adjustment lever

4

. It

may loosen in time and hit the base plate beforetighten ing.

To Tighten the Lever:

1. Hold depth adjustment lever

4

and loosen the locknut

18

2. Adjust the depth adjustment lever by rotating it in the

desired direction about 1/8 of arevolution.

3. Retightennut.

Bevel Angle Adjustment (Fig.A,G)

The bevel angle adjustment mechanism can be adjusted

between 0° and 57°.

To achieve better accuracy in cutting, use the fine adjustment

markings located on the pivot bracket

21

1. Raise the bevel adjustment lever

10

toloosen.

2. Tilt the base plate to the desired angle by aligning the fine

bevel pointer

22

with the desired angle mark on the pivot

bracket

21

3. Lower the bevel adjustment lever toretighten.

Bevel Detent (Fig.A, G)

The DCS570 is equipped with a bevel detent feature. As you

tilt the base plate

5

you will hear a click and feel the base

plate stop at both 22.5 and 45 degrees. If either of these is the

desired angle, retighten the lever

10

by lowering it. If you

desire another angle, continue tilting the base plate until the

coarse bevel pointer

23

or the fine pointer

22

aligns with the

desiredmark.

Cut Length Indicator (Fig.A)

The markings on the side of the base plate

5

show the length

of the slot being cut into the material at the full depth of the cut.

The markings are in increments of 5mm.

Kerf Indicator (Fig.I)

The front of the saw base plate has a kerf indicator

9

for vertical

and bevel cutting. This indicator enables you to guide the saw

along cutting lines penciled on the material being cut. The kerf

indicator lines up with the left (outer) side of the saw blade,

which makes the slot or “kerf” cut by the moving blade fall to

the right of the indicator. Guide along the penciled cutting line

so that the kerf falls into the waste or surplus material.

Mounting and Adjusting the Parallel Fence

(Fig.N)

The parallel fence

28

is used for cutting parallel to the edge of

theworkpiece.

Mounting

1. Slacken the parallel fence adjustment knob

27

to allow the

parallel fence topass.

2. Insert the parallel fence

28

in the base plate asshown.

3. Tighten the parallel fence adjustment knob

27

ENGLISH

Adjusting

1. Slacken the fence adjustment knob

27

and set the parallel

fence

28

to the desired width. The adjustment can be read

on the parallel fencescale.

2. Tighten the fence adjustment knob

27

Mounting the Dust Extraction Port

(Fig.A, P)

Your circular saw is supplied with a dust extractionport.

To Install the Dust Extraction Port

1. Fully loosen depth adjustment lever

4

2. Place the base plate

5

in the lowestposition.

3. Align the left half of the dust extraction port

29

over upper

blade guard

7

as shown. Be sure to insert the tab into the

casting notch on the tool. When installed correctly, it will

snap fully over the original depth of cutpointer.

4. Align the right-hand piece

30

with theleft.

5. Insert screws and tightensecurely.

Prior to Operation

• Make sure the guards have been mounted correctly. The

saw blade guard must be in closedposition.

• Make sure the saw blade rotates in the direction of the

arrow on theblade.

• Do not use excessively worn sawblades.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. J)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires one hand on the main handle

26

, with the other hand on the auxiliary handle

12

LED Worklight (Fig.A)

The LED worklight

15

is activated when the trigger switch is

depressed. When the trigger is released, the worklight will stay

illuminated for up to 20seconds.

NOTE: The worklight is for lighting the immediate work surface

and is not intended to be used as aflashlight.

Switching On and Off (Fig.B)

For safety reasons the trigger switch

2

of your tool is equipped

with a lock-off button

1

Press the lock-off button to unlock thetool.

To run the tool, press the trigger switch

2

. As soon as the

trigger switch is released, the lock-off switch is automatically

activated to prevent unintended starting of themachine.

NOTICE: Do not switch the tool ON or OFF when the saw

blade touches the workpiece or othermaterials.

Workpiece Support (Fig.J–M)

WARNING: To reduce the risk of serious personal

injury, support the work properly and hold the

saw firmly to prevent loss ofcontrol.

Figures J and K show proper sawing position. Figures L and M

show an unsafe condition. Hands should be kept away from

cutting area, and power cord is positioned clear of the cutting

area so that it will not get caught or hung up on thework.

To avoid kickback, ALWAYS support board or panel NEAR the

cut, (Fig. J and K). DON’T support board or panel away from the

cut (Fig.L and M). When operating the saw, keep the cord away

from the cutting area and prevent it from becoming hung up on

the workpiece.

ALWAYS DISCONNECT SAW BEFORE MAKING ANY ADJUST-

MENTS! Place the work with its “good” side—the one on which

appearance is most important—down. The saw cuts upward,

so any splintering will be on the work face that is up when you

sawit.

Cutting (Fig. J)



WARNING: Never attempt to use this tool by resting it

upside down on a work surface and bringing the material

to the tool. Always securely clamp the workpiece and

bring the tool to the workpiece, securely holding the tool

with two hands as shown in FigureJ.

Place the wider portion of the saw base plate on that part of

the work piece which is solidly supported, not on the section

that will fall off when the cut is made. As examples, FigureJ

illustrates the RIGHT way to cut off the end of a board. Always

clamp work. Don’t try to hold short pieces by hand! Remember

to support cantilevered and overhanging material. Use caution

when sawing material frombelow.

Be sure saw is up to full speed before blade contacts material

to be cut. Starting saw with blade against material to be cut

or pushed forward into kerf can result in kickback. Push the

saw forward at a speed which allows the blade to cut without

laboring. Hardness and toughness can vary even in the same

piece of material, and knotty or damp sections can put a heavy

load on the saw. When this happens, push the saw more slowly,

but hard enough to keep working without much decrease

in speed. Forcing the saw can cause rough cuts, inaccuracy,

kickback, and over-heating of the motor. Should your cut begin

to go off the line, don’t try to force it back on. Release the switch

and allow blade to come to a complete stop. Then you can

withdraw the saw, sight anew, and start a new cut slightly inside

the wrong one. In any event, withdraw the saw if you must shift

ENGLISH

the cut. Forcing a correction inside the cut can stall the saw and

lead tokickback.

IF SAW STALLS, RELEASE THE TRIGGER AND BACK THE SAW

UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE CUT AND

CLEAR OF THE CUTTING EDGE BEFORERESTARTING.

As you finish a cut, release the trigger and allow the blade to

stop before lifting the saw from the work. As you lift the saw,

the spring-tensioned telescoping guard will automatically close

under the blade. Remember the blade is exposed until this

occurs. Never reach under the work for any reason. When you

have to retract the telescoping guard manually (as is necessary

for starting pocket cuts) always use the retractinglever.

NOTE: When cutting thin strips, be careful to ensure that small

cutoff pieces don’t hang up on inside of lowerguard.

Pocket Cutting (Fig.O)



WARNING: Never tie the blade guard in a raised position.

Never move the saw backwards when pocket cutting. This

may cause the unit to raise up off the work surface which

could causeinjury.

A pocket cut is one that is made in a floor, wall or other

flatsurface.

1. Adjust the saw base plate so the blade cuts at desireddepth.

2. Tilt the saw forward and rest front of the base plate on

material to becut.

3. Using the lower guard lever, retract lower blade guard to an

upward position. Lower rear of base plate until blade teeth

almost touch cuttingline.

4. Release the blade guard (its contact with the work will keep

it in position to open freely as you start the cut). Remove

hand from guard lever and firmly grip auxiliary handle

12

as shown in FigureO. Position your body and arm to allow

you to resist kickback if itoccurs.

5. Make sure blade is not in contact with cutting surface before

startingsaw.

6. Start the motor and gradually lower the saw until its base

plate rests flat on the material to be cut. Advance saw along

the cutting line until cut iscompleted.

7. Release trigger and allow blade to stop completely before

withdrawing the blade from thematerial.

8. When starting each new cut, repeat asabove.

Dust Extraction (Fig.Q)



WARNING: Risk of dust inhalation. To reduce the risk of

personal injury, ALWAYS wear an approved dustmask.

A dust extraction port

30

is supplied with yourtool.

The Dust Extraction Adaptor

31

allows you to connect the tool

to an external dust extractor, either using the AirLock™ system

(DWV9000-XJ), or a standard 35mm dust extractorfitment.



WARNING: ALWAYS use a vacuum extractor designed

in compliance with the applicable directives regarding

dust emission when sawing wood. Vacuum hoses of most

common vacuum cleaners will fit directly into the dust

extractionoutlet.

MAINTENANCE

Your DeWALT power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Self lubricating ball and roller bearings are used in the tool and

relubrication is not required. However, it is recommended that,

once a year, you take or send the tool to a service center for a

thorough cleaning, inspection and lubrication of the gearcase.

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lower Guard

The lower guard should always rotate and close freely from

a fully open to fully closed position. Always check for correct

operation before cutting by fully opening the guard and letting

it close. If the guard closes slowly or not completely, it will

need cleaning or servicing. Do not use the saw until it functions

correctly. To clean the guard, use dry air or a soft brush to

remove all accumulated sawdust or debris from the path of

the guard and from around the guard spring. Should this not

correct the problem, it will need to be serviced by an authorized

servicecenter.

Base Plate Adjustment (Fig.G, H)

Your base plate has been factory set to assure that the blade is

perpendicular to the base plate. If after extended use you need

to re-align the blade, follow the directions below:

Adjusting for 90 Degree Cuts

1. Return the saw to 0degreesbevel.

ENGLISH

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

2. Place the saw on its side, and retract the lowerguard.

3. Set the depth of cut to 51mm.

4. Loosen the bevel adjustment lever (

10

, Fig.G). Place a

square against the blade and the base plate as shown in

FigureH.

5. Using a wrench, turn the set screw (

25

, Fig. H) on the

underside of the base plate until the blade and the base

plate are both in flush contact with the square. Retighten

the bevel adjustmentlever.

Adjusting Bevel Adjustment Lever

It may be desirable to adjust the bevel adjustment lever

10

. It

may loosen in time and hit the base plate beforetighten ing.

To Tighten the Lever:

1. Hold the bevel adjustment lever

10

and loosen the bevel

locknut

24

2. Adjust the bevel adjustment lever by rotating it in the

desired direction about 1/8 of arevolution.

3. Retightennut.

Blades

A dull blade will cause inefficient cutting, overload on the

saw motor, excessive splintering and increase the possibility

of kickback. Change blades when it is no longer easy to push

the saw through the cut, when the motor is straining, or when

excessive heat is built up in the blade. It is a good practice to

keep extra blades on hand so that sharp blades are available for

immediate use. Dull blades can be sharpened in mostareas.

Hardened gum on the blade can be removed with kerosene,

turpentine, or oven cleaner. Anti-stick coated blades can be

used in applications where excessive build-up is encountered,

such as pressure treated and greentimber.

Optional Accessories



WARNING: Since accessories, other than those offered

by DeWALT, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only DeWALT recommended

accessories should be used with thisproduct.

DO NOT USE WATER FEED ATTACHMENTS WITH THISSAW.

VISUALLY EXAMINE CARBIDE BLADES BEFORE USE. REPLACE

IFDAMAGED.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

繁體中文



表示觸電危險。



表示火災危險。

電動工具一般安全警告



不遵

循這些警告及指示可能會導致觸電、火災及/或

嚴重傷害。

請妥善保存所有警告及指示以備將來查閱

警告中的名詞電動工具

是指電源驅動 (插電)

電動工具，或者電池驅動 (充電) 電動工具。

為了降低受傷的風險，必須仔細閱讀使

用手冊。

定義：安全指南

以下定義描述了每一個詞彙的嚴重程度。請閱讀本手

冊並注意這些符號。



表示緊急危險狀況若未能避免導致



表示潛在危險情況若未能避免導

致



表示潛在危險情況若未能避免導

致

恭喜！

感謝您選購

DeWALT

工具。憑藉多年的經驗、完善的產品開發與創新，

DeWALT

已成為專業電動工具使用者最

可靠的合作夥伴之一。請注意！各地區上市產品/配件不盡相同，請依台灣繁體中文說明書的內容為主。

注意：20V Max 為最大初始電池電壓 (無負載測量)，標稱電壓為 18V。60V Max 為最大初始電池電壓 (無負載

測量)，標稱電壓為

54V。

技術資料

DCS570

最大/標稱電壓伏特

直流

20/18

類型

電池類型鋰離子電池

空載轉速轉/分

5500

鋸片直徑公釐

190

最大切割深度公釐

鋸片孔徑

公釐

25.4

斜角調整

重量（不包括電池組）千克

3.6

表示一種的行為，若未能避免，導致。

無碳刷圓鋸機

DCS570

目錄號伏特

直流

安時

重量

千克

DCB107 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546/DCB606 18/54 6.0/2.0 1.05 270 140 90 60 90 X

DCB547/DCB609 18/54 9.0/3.0 1.25 420 220 140 85 140 X

DCB181 18 1.5 0.35 70 35 22 22 22 45

DCB182/DCB204 18 4.0 0.61 185 100 60 60 60 120

DCB183/B 18 2.0 0.40 90 50 30 30 30 60

DCB184/B/DCB205 18 5.0 0.62 240 120 75 75 75 150

DCB185 18 1.3 0.35 60 30 22 22 22 X

DCB187 18 3.0 0.48 140 70 45 45 45 90

ページが読み込まれています...

DeWalt DCS570 ユーザーマニュアル

ブランド: DeWalt

モデル: DCS570

カテゴリー: パワーツール

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: DeWalt DCS570 User manual

DeWalt DCS570 ユーザーマニュアル

DeWalt DCS570 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント