Radiomaster TX12MKII ユーザーガイド

WWW.RADIOMASTERRC.COM

Quick start guide

TX12MKII

Introduction

Thank you for purchasing the RadioMaster TX12MKII 2.4g remote control system. The system is versatile and

can be used by beginners and professionals. In order to ensure the correct and safe use of this product,

please read this manual carefully before use. Due to constant improvements in software and hardware this

manual may change over time. The information contained in this manual is subject to change without notice.

Visit our website for the most up to date information.

TX12MKII remote control is suitable for all types of fixed-wing aircraft, gliders, helicopters, cars, boats,

robotics, multi-rotor aircraft and anything else you might create, if you can build it RadioMaster can control it.

The TX12MKII uses a powerful operating system called EdgeTX, for more information visit the links below.

-The RadioMaster team.

Many remote-control models are equipped with powerful motors and sharp propellers. When using or

maintaining models, proceed with caution. When performing assembly or maintenance, make sure to

disconnect the power to the model and remove the propellers.

Do not operate the TX12MKII remote control system under the following conditions:

• In severe weather or strong windy conditions, such as rain, hail, snow, storms or electromagnetic environ-

ments.

• In any situation where visibility is limited.

• In areas where people, property, high-voltage power lines, public roads, vehicles or animals may be present.

• If you feel tired or unwell, or under the influence of drugs or alcohol.

• If the remote control or model seems to be damaged or not working properly.

• In areas with high 2.4GHz interference or where 2.4GHz radio is prohibited.

• When the radios battery voltage is too low to be used.

• In areas where local regulations prohibit the use of aviation models.

Safety Information

Manual and firmware download

TX12MKII is pre-installed with factory approved EdgeTX firmware. To download the latest software manual,

please visit the RadioMaster website: https://www.radiomasterrc.com

To download the latest firmware for your TX12MKII remote control, please visit the EdgeTX website:

https://www.Edge-tx.org

Important

ANTENNA: Install the provided antenna in the top of the radio BEFORE installing batteries and turning on the

radio. DO NOT operate the radio without the antenna installed and the internal RF module powered on. Doing

so will damage the internal RF module and will not be covered under warranty.

FIRMWARE: The TX12MKII is pre-installed with the most stable firmware at the factory at time of release.

please only attempt to update the firmware if you are confident in the process. Incorrect firmware updates

may cause the remote control to become inoperable.

Remote control overview

TX12MKII has a built-in USB-C charging function for 3.7v to 4.2v lithium battery. The charging circuit is only

suitable for 2x 3.7v Li-ion 18650 or 2x 3.7v Lipoly batteries (2s 7.4v Lipo battery pack), the nominal battery

voltage is 3.7v, and the maximum charging voltage is 4.2v.

Do not use LiFE battery packs or 18650 lithium-ion batteries with a nominal voltage of 3.6v to 4.10v. Charging

the incorrect type of battery may damage the charger or cause a fire.

Please check the voltage and condition of the battery regularly and never charge it unattended. Always charge

in a safe area away from combustible materials. If the remote control gets wet or damaged in any way, do not

charge it.

RadioMaster does not assume any responsibility for any adverse consequences caused by the use or misuse

of this product.

SF 3 PositionSE 3 Position

Trainer Port TYPE-C USB

SB 3 Position SC 3 Position

SD ButtonSA Button

S2 Slider PotS1 Slider Pot

Right GimbalLeft Gimbal

Power Button

MDL ButtonSYS Button

Trim Buttons

LCD Screen

Antenna

Handel

RTN Button

PAGE> Button

PAGE< Button

TELE Button

Menu Wheel

TYPE-C charger port

Model selection and protocol selection (CC2500 version)

Notes

Model selection and protocol selection (ELRS version)

The TX12MKII comes with a CC2500 single-chip multi-protocol internal RF module, which is compatible

with several different protocols. To view the latest list of all compatible protocols, please visit https://www.-

multi-module.org/ Please note that new protocols will be constantly updated and added to the latest

firmware. Some new protocols may require firmware upgrades.

TX12MkII ELRS units are equipped with an internal ELRS module, capable of providing 10mW-250mW

RF output. In non-extreme circumstances, 100mW output at 250Hz update rate is recommended, as

higher RF output and update rates may significantly reduce battery life and generate excessive heat.

Bind instructions

1Turn off the transmitter

2Cycle power to the receiver 3 times, the receiver LED will flash twice- indicating bind mode.

3Turn on the transmitter, long press the SYS button and choose the ExpressLRS LUA under the

TOOLS menu. Scroll down to [Bind] and press enter.

4The LED on the receiver should now be solid, indicating successful bind.

• Long press the MDL button to enter the model settings, select MULTI in the SETUP page, and select the

protocol to be used in the sub-options. The system will automatically turn on the corresponding RF

module according to the RF protocol you selected.

• Bind [BND] is used to start the binding process.

• Range [RNG] button can reduce the power to 1/30 to facilitate testing of remote-control distance.

EdgeTX software is very powerful, and has a large number of programming and mixing functions. Please

download the comprehensive software installation guide from the link below for more detailed instructions:

https://www.Edge-tx.org or https://www.radiomasterrc.com

Specifications

Size 170*159*108mm

Weight 363g

Frequency 2.400GHZ-2.480GHZ

RF Chip Single-chip Multi-protocol CC2500SX1280 (ELRS)

Supported ProtocolsCorona HitecFutaba S-FHSSFrsky D16/D8RadioLinkGraupner HoTT* (CC2500)

ExpressLRS (ELRS version)

Transmitting Power 20dBm

Antenna Gain 2db

Voltage Range6.6-8.4v DC

Range > 2km @ 20dbm (depending on receiver)

Radio Firmware EdgeTX Transmitter/ Multi-Module RF module) / ELRS

Channels Up to 16 (depending on receiver)

Display128*64 Monochrome LCD display

Gimbal High precision Hall gimbals

External module JR/FrSKY/Crossfire compatible

Upgrade Method USB/SD card & EdgeTX Companion PC software

* For the most up to date list on supported protocols please visit https://www.multi-module.org/

Warranty and repair

Firmware update and EdgeTX

If there is any problem with your remote control hardware, please keep the proof of purchase and contact the

retailer where you purchased the TX12MKII. You may also visit our warranty support page https://www.radio-

masterrc.com/contact

For the latest information and firmware updates from the EdgeTX open source firmware development team,

please visit the EdgeTX website at https://https://www.Edge-tx.org.

EU Simple Declaration of Conformity

Manufacturer by

RadioMaster declares the radio equipment TX12 is in compliance with EU directives Directive

2014/53/EU. Full text of the declaration of conformity is available at the following website www.radio-

masterrc.com

ShenZhen RadioMaster Co., Ltd

4th Floor, Yangtian Building, No. 18 Yangtian Road, Xin’an Street, Baoan District, Shenzhen, Guangdong.

FCC ID: 2AV3G-TX12

FCC Information

CAUTION:

Antenna Separation Distance

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules.

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation. Full text of

the declaration of conformity is available at the following website www.radiomasterrc.com

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment. This product contains a radio transmitter with

wireless technology which has been tested and found to be compliant with the applicable

regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

When operating your RadioMaster transmitter, please be sure to maintain a separation distance

of at least 20 cm between your body (excluding fingers, hands, wrists, ankles and feet) and the

antenna to meet RF exposure safety requirements as determined by FCC regulations.

简介

感谢您购买RadioMaster TX12MKII 2.4g遥控系统。该系统用途广泛，可供初学者和专业人士使用。为了确保正

确、安全地使用本产品，请在使用前仔细阅读本使用说明书。由于版本升级，已经进行了更改。本手册中包含

的信息如有更改，恕不另行通知。

TX12MKII遥控器适用于所有类型的固定翼、滑翔机、直升机和多旋翼飞机。可以根据使用的航空器选择型号类

型，并可以使用各种混合功能。

-RadioMaster 团队敬上

许多遥控模型都配备了强大的电机和锋利的螺旋桨。使用模型时，请谨慎行事。进行组装或维护时，请确保

已断开模型的电源并卸下螺旋桨。

在以下情况下，请勿操作TX12MKII遥控系统：

· 在恶劣天气或强风条件下，例如雨，冰雹，下雪，暴风雨或电磁环境中。

· 在能见度有限的任何情况下。

· 在可能存在人员、财产、电力高压线、公共道路、有车辆或动物的区域。

· 如果您感到疲倦或不适，或在药物或酒精的影响下。

· 如果遥控器或模型似乎已损坏或无法正常工作。

· 在2.4GHz干扰较大的区域或禁止使用2.4GHz无线电的地方。

· 当电池电压太低而无法使用时。

· 在当地法规禁止使用航空模型的区域。

安全须知

说明书和固件下载

TX12MKII预装标准的EdgeTX固件。要下载最新的软件手册，请访问RadioMaster网站：

https://www.radiomasterrc.com

要为您的TX12MKII遥控器下载最新的固件，请访问EdgeTX网站： https://www.Edge-tx.org

警告！

TX12MKII出厂时预装最稳定的固件。如果您有经验并且有信心更新系统固件，请仅更新固件。不正确的更新

可能会导致遥控器无法操作。

遥控器概述

电源和充电注意事项

TX12MKII内置USB-C充电功能，可用于3.7v至4.2v的锂电池。该充电电路仅适用于2x 3.7v锂离子18650电

池或2x 3.7v Lipoly电池(2s 7.4v Lipo电池组)，标称电池电压为3.7v，最大充电电压为4.2v。

不要使用标称电压为3.6v至4.10v的寿命电池组或18650锂离子电池。给不正确的电池充电可能会损坏充电

器或引起火灾。

请定期检查电池的电压和状态，切勿在无人看管的情况下充电。总是在远离易燃材料的安全区域充电。如

果遥控器湿了或损坏了，不要给它充电。

RadioMaster不承担因使用或误用本产品而造成的任何不良后果。

天线

提手

SF三段开关SE三段开关

DSC教练插口 TYPE-C USB

SB三段开关 SC三段开关

SD按键开关SA按键开关

S2电位器滑块S1电位器滑块

右摇杆左摇杆

电源开关

MDL按键SYS按键

SRTN按键

TELE按键

PAGE>右翻页

PAGE<左翻页

数字微调

导航滚轮及ENT按键

显示屏

TYPE-C 充电口

模型选择及协议选择(内置CC2500多协议高频模块)

模型选择及协议选择(内置ELRS高频模块)

TX12MKII CC2500多协议版本可以兼容多种不同的协议，要查看所有兼容协议的最新列表，请访问

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md

请注意，新协议会不断更新并被添加到最新固件中，新的某些协议可能需要升级固件。

TX12MKII内置ELRS具有10mW-250mW可调范围，最大功率为250mW，在非极限条件使用时，推荐将功率

限制为100mW，并使用250Hz速率，更高的速率会降低控制距离，更高的功率会带来较大的发热和耗电，请您

根据自身需求，合理调整功率及速率，以便达到性能和耗电的平衡。

·请长按MDL按钮进入模型设置，在SETUP页面中选择MULTI，并在子选项中选择需要使用的协议。系统根

据您选择的射频协议，会自动开启对应的射频模块，同时关闭其它三个射频模块。系统在同一时间只会开启

一个射频模块，以确保没有多余的无线电信号相互干扰。

·Bind按钮用于启动对频过程。

·Range按钮可将功率降低至1/30，以方便测试遥控距离。

注意

EgdeTX软件非常强大，并且具有大量的编程和混控功能。请从下面的链接下载综合软件安装指南

以获取更详细的说明： https://www.Egde-tx.org

技术指标

规格尺寸：170*159*108毫米

重量：363克

传输频率：2.400GHZ-2.480GHZ

发射器模块：单芯片多协议高频模块（CC2500)/ExpressLRS内置模块(ELRS)

支持的协议：Corona 、Hitec 、Futaba S-FHSS 、Frsky D16/D8 、RadioLink 、

Graupner HoTT等（多协议版本）

ExpressLRS （ELRS版本）

发射功率：最大20dBm

天线增益：2db

工作电压：6.6-8.4v DC

遥控距离：> 2km @ 20dbm

开源固件：EdgeTX （遥控器）/DIY-Multiprotocol-TX-Module （高频模块）/ELRS

通道数：最多16个通道（取决于接收器）

显示：128*64单色LCD显示器

摇杆：霍尔版

外置模块：JR/FrSKY兼容模块插座

升级方法：支持USB在线/SD卡离线升级

协议：多协议支持的所有协议（有关多协议支持的协议列表，请访问

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md）

保修及维修

固件更新和EdgeTX信息

用户手册

欧盟认证合格声明

制造商

深圳RadioMaster有限公司

广东省深圳市宝安区新安街道72区杨田路扬田大厦4楼

RadioMaster无线电设备TX12符合欧盟指令2014/53/EU。符合性认证声明的全文可在以下

网站上找到：www.radiomasterrc.com

如果您的遥控器硬件出现任何问题，请保留购买证明并与您购买TX12MKII的零售商联系。

有关EdgeTX开源固件开发团队的最新资讯和固件更新，请访问EdgeTX网站，网址为

https://www.Edge-tx.org 。

有关TX12MKII EdgeTX系统固件的详细用户手册，请访问https://www.Edge-tx.org

FCC ID: 2AV3G-TX12

FCC 认证信息

警告：

安全的天线距离

T该设备已经过测试，符合FCC规则第15章的规定。操作必须符合以下两个条件：

（1）此设备不会造成有害干扰

（2）此设备必须接受收到的任何干扰，包括可能导致意外操作的干扰。

符合性声明的全文可在以下网站上找到：www.radiomasterrc.com

未经负责合规方明确批准的更改或修改可能会使用户丧失操作设备的权限。

本产品包含具有天线技术的无线电发射器，该无线电发射器已经过测试，符

合适用于2.400GHz至2.4835GHz频率范围内的无线电发射器的适用法规。

操作RadioMaster发射器时，请确保您的身体（不包括手指，手，腕，脚踝和脚）与天线之间

保持至少20cm的距离，以符合FCC法规确定的RF暴露安全要求。

Radiomaster TX12MKII ユーザーガイド

関連論文

その他の書類