Tascam MZ-372 取扱説明書

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

日本語

OWNER'S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

取扱説明書

LX372G0003

MZ-372

MIXER

2 TASCAM MZ-372

• TASCAMisatrademarkofTEACCORPORATION,

registeredintheU.S.andothercountries.

• Othercompanynames,productnamesand

logosinthisdocumentarethetrademarks

orregisteredtrademarksoftheirrespective

owners.

TEACCORPORATION

https://tascam.jp/jp/

Phone:+81-42-356-9143

1-47Ochiai,Tama-shi,Tokyo206-8530Japan

TEACAMERICA,INC.

https://tascam.com/us/

Phone:+1-323-726-0303

10410PioneerBlvd.Suite#1and#4,

SantaFeSprings,California90670,U.S.A.

TEACUKLtd.

https://tascam.eu/

Phone:+44-1923-797205

MeridienHouse,69-71ClarendonRoad,

Watford,Herts,WD171DS,UnitedKingdom

TEACEUROPEGmbH

https://tascam.de/

Phone:+49-611-71580

Bahnstrasse12,65205Wiesbaden-Erbenheim,

Germany

TEACSALES&TRADING(SHENZHEN)CO.,LTD

http://tascam.cn/

Phone:+86-755-88311561~2

Room817,XinianCenterA,TairanNineRoadWest,

ShennanRoad,FutianDistrict,Shenzhen,

GuangdongProvince518040,China

TASCAM MZ-372 3

IMPORTANT SAFETY PRECAUTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and mainte-

nance (servicing) instructions in the literature accompanying the

appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZ-

ARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

For U.S.A.

Declaration of Conformity

Model Number: MZ-372

Trade Name: TASCAM

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1 and #4, Santa

Fe Springs, California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation.

INFORMATION TO THE USER

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instruction manual,

may cause harmful interference to radio communi-

cations. However, there is no guarantee that inter-

ference will not occur in a particular installation. If

this equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interference

by one or more of the following measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment

and receiver.

c) Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

d) Consult the dealer or an experienced radio/TV

technician for help.

CAUTION

Changes or modifications to this equipment not

expressly approved by TEAC CORPORATION for

compliance could void the user’s authority to oper-

ate this equipment.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST

CONFORME A LA NORME NMB-003 DU CANADA.

This product complies with the

European Directives request and the

other Commission Regulations.

CE Marking Information

EN55103-2

a) Applicable electromagnetic environment: E1, E2,

E3, E4

OWNER’S MANUAL

4 TASCAM MZ-372

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as ra-

diators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polar-

ized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong. The wide blade or the third

prong are provided for your safety. If the provid-

ed plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

11. Only use attachments/accessories specified by

the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has

been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

0The mains plug is used as the disconnect de-

vice, the disconnect device shall remain readily

operable.

0Caution should be taken when using earphones

or headphones with the product because exces-

sive sound pressure (volume) from earphones or

headphones can cause hearing loss.

0If you are experiencing problems with this prod-

uct, contact TEAC for a service referral. Do not use

the product until it has been repaired.

0Do not remove the external cases or cabinets to

expose the electronics. No user serviceable parts

are inside.

0If you are experiencing problems with this prod-

uct, contact the store where you purchased the

unit for a service referral. Do not use the product

until it has been repaired.

0Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

CAUTION

0Do not expose this apparatus to drips or

splashes.

0Do not place any objects filled with liquids, such

as vases, on the apparatus.

0Do not install this apparatus in a confined space

such as a book case or similar unit.

0The apparatus should be located close enough

to the AC outlet so that you can easily grasp the

power cord plug at any time.

0If the product uses batteries (including a battery

pack or installed batteries), they should not be

exposed to sunshine, fire or excessive heat.

0CAUTION for products that use replaceable

lithium batteries: there is danger of explosion

if a battery is replaced with an incorrect type of

battery. Replace only with the same or equiva-

lent type.

TASCAM MZ-372 5

RACK-MOUNTING THE UNIT

Use the supplied rack-mounting kit to mount the unit

in a standard 19-inch rack, as shown below.

CAUTION

i Leave 1U of space above the unit for ventilation.

i Allow at least 10 cm (4 in) at the rear of the unit

for ventilation.

Rack-mounting using the universal holes

To use the universal holes of this unit to mount it in a

rack, install it with the rackmount screw kit as shown

in the illustrations below.

Universal Hole position

Installation in a 4U space

Use the a holes to mount the unit in the rack.

Installing this way creates gaps above and below the

MZ-372 (c).

These gaps can be used to route cables connected to

the back of the unit, for example.

Cable

Installation in a 3U or larger space

Use the b holes to mount the unit in the rack.

6 TASCAM MZ-372

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste

stream via designated collection facilities appoint-

ed by the government or the local authorities.

(b) By disposing of the electrical and electronic

equipment correctly, you will help save valuable

resources and prevent any potential negative

effects on human health and the environment.

(c) Improper disposal of waste equipment can have

serious effects on the environment and human

health as a result of the presence of hazardous

substances in electrical and electronic equipment.

(d) The crossed out wheeled dust bin symbol

indicates that electrical and electron-

ic equipment must be collected and

disposed of separately from household

waste.

(e) The return and collection systems are available

to the end users. For more detailed information

about disposal of old electrical and electronic

equipment, please contact your city office, waste

disposal service or the shop where you purchased

the equipment.

For China

“仅适用于海拔2000m 以下地区安全使用”

“仅适用于非熱帯气候条件下安全使用”

“環境保護使用年限”

产品有毒有害物质或元素的名称及含量

机种: MZ-372 有毒有害物质或元素

品名铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

1 CHASSIS 部份 ○ ○ ○ ○ ○ ○

2 FRONT PANEL 部份 ○ ○ ○ ○ ○ ○

3 螺丝部份 ○ ○ ○ ○ ○ ○

4 线材部份 ○ ○ ○ ○ ○ ○

5 PCB Assy 部份 × ○ ○ ○ ○ ○

6 电源部份 ○ ○ ○ ○ ○ ○

7 附属品部份 × ○ ○ ○ ○ ○

8 LABEL 部份 ○ ○ ○ ○ ○ ○

9 包装部份 ○ ○ ○ ○ ○ ○

○ ：表示该有毒有害物质在该部件所有均质材料中的含有量均在 GB/T26572 标准规定的限量要求以下。

× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572 标准规定的限量要求。

(针对现在代替技术困难的电子部品及合金中的铅 ))

TASCAM MZ-372 7

Thank you very much for purchasing the TASCAM

MZ−372.

Before using this unit, read this Owner’s Manual care-

fully so that you will be able to use it correctly and

enjoy working with it for many years. After you have

finished reading this manual, please keep it in a safe

place for future reference.

You can also download this Owner’s Manual from the

TEAC Global Site (http://teac-global.com/).

Features

0Rackmount mixer with numerous input channels

and two pairs of main outputs

0Six input channels are equipped with gain con-

trols, LED level meters, three-band equalizers and

faders Mic or line input can be easily selected with

switches

0Independent front mic input with volume control

and two-band equalizer

0Talkover function automatically lowers back-

ground music volume according to mic volume

0Two main outputs with stereo LED level meters

0Sub output with volume control and mono/stereo

output format selection

0Headphone output with volume control can be

used for pre-fader monitoring of selected input

channels and the main output

03U rackmount size

Items included with this product

This product includes the following items.

Take care when opening the package to avoid

damaging the items. Keep the packing materials for

transportation in the future.

Please contact the store where you purchased this

unit if any of these items are missing or have been

damaged during transportation.

0Main unit ...........................................................................× 1

0AC adapter (TASCAM PS-M1524) ............................. × 1

0Cord for AC adapter (JAPAN USA/EUROPE) ..........× 2

0Rackmount screw kit .................................................... × 1

0Owner’s Manual (this document)

including warranty ........................................................× 1

CAUTION

Always use the included AC adapter (TASCAM

PS-M1524) when using this unit. Never use the

included AC adapter with any other device. Doing

so could cause damage, fire or electric shock.

Contents

IMPORTANT SAFETY PRECAUTIONS....................... 3

IMPORTANT SAFETY INSTRUCTIONS ..................... 4

Features .................................................................... 7

Items included with this product ........................... 7

Conventions used in this manual ........................... 8

Precautions for placement and use ........................ 8

Beware of condensation ......................................... 8

Cleaning the unit ..................................................... 8

Using the TEAC Global Site ..................................... 8

Product registration ................................................ 8

About TASCAM customer support service ............. 8

Names and functions of parts ................................ 9

Front panel ............................................................................9

Rear panel ........................................................................... 10

Preparation ............................................................ 11

Connecting the power ................................................... 11

Attaching the cord ........................................................... 11

Connecting other equipment...................................... 12

Turning the power on and off...................................... 13

Operation procedures ........................................... 14

Adjusting mic input channels (1-6)............................ 14

Adjusting line input channels (1-6) ........................... 14

Adjusting the input of a mic connected to the

MAIN MIC INPUT jack ...................................................... 14

Output channels ............................................................... 14

Using the talkover function .......................................... 15

Listening to channel pre-fader signals ..................... 15

Troubleshooting .................................................... 15

Specifications ......................................................... 16

Audio inputs ....................................................................... 16

Audio outputs ................................................................... 16

Audio performance ......................................................... 16

General ................................................................................. 17

Dimensional drawings.................................................... 17

Block diagram .................................................................... 18

8 TASCAM MZ-372

Conventions used in this manual

In this manual, we use the following conventions:

0The names of switches, connectors and other

physical parts of this unit are written using a bold

font like this: POWER switch.

0Additional information is provided as necessary as

tips, notes and cautions.

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and de-

scribe special cases.

CAUTION

Failure to follow these instructions could result

in injury, damage to equipment or lost recording

data, for example.

Precautions for placement and use

0The operating temperature range of this unit is

5–35 °C.

0Do not install this unit in the following types of

locations. Doing so could cause malfunction.

Places with significant vibrations

Near windows or other places exposed to

direct sunlight

Near heaters or other extremely hot places

Extremely cold places

Places with bad ventilation or high humidity

Very dusty locations

0To enable good heat dissipation, do not place

anything on top of the unit.

0Do not place the unit on top of a power amplifier

or other device that generates heat.

Beware of condensation

If the unit is moved from a cold to a warm place,

or used after a sudden temperature change, there

is a danger of condensation; vapor in the air could

condense on the internal mechanism, making correct

operation impossible.

To prevent this, or if this occurs, let the unit sit for one

or two hours at the new room temperature before

using it.

Cleaning the unit

To clean the unit, wipe it gently with a soft dry cloth.

Do not wipe with chemical cleaning cloths, benzene,

thinner, alcohol or other chemical agents. Doing so

could damage the surface or cause discoloration.

Using the TEAC Global Site

You can download updates for this unit from the

TEAC Global Site:

http://teac-global.com/

In the TASCAM Downloads section, select the desired

language to open the Downloads website page for

that language.

Product registration

Customers in the USA, please visit the following TAS-

CAM website to register your TASCAM product online.

https://tascam.com/us/

About TASCAM customer support

service

TASCAM products are supported and warrantied only

in their country/region of purchase.

To receive support after purchase, on the TASCAM

Distributors list page of the TEAC Global Site (http://

teac-global.com/), search for the local company or

representative for the region where you purchased

the product and contact that organization.

When making inquiries, the address (URL) of the shop

or web shop where it was purchased and the pur-

chase date are required.

Moreover, the warranty card and proof of purchase

might also be necessary.

TASCAM MZ-372 9

Names and functions of parts

Front panel

1 MAIN MIC INPUT VOLUME knob

Use to adjust the mic input level from the MAIN

MIC INPUT jack (w).

2 MAIN MIC switch and indicator

Press to turn mic input from the MAIN MIC INPUT

jack (w) on/off.

The MIC indicator lights when mic input is on.

3 TALKOVER switch/indicator

Press to turn the talkover function on/off.

When the talkover function is on, the TALKOVER

indicator lights, and the levels of all input chan-

nels are lowered automatically when sound is

input from a mic connected to the MAIN MIC

INPUT.

4 GAIN knobs

Use these to adjust the levels of each input

channel.

5 SOURCE SELECT switches/indicators

Use these to set the input source to the C (MONO)

/MIC (h) or LINE A/B (v) input jacks on the back

of the unit.

The indicator for the selected input lights.

6 Channel faders

Use these to adjust the send levels of channel

signals.

7 Output level indicators

These indicators show the output levels of the

MAIN OUTPUTS 1-2 (UNBALANCED) (f) jacks and

MAIN OUTPUTS 1-2 (BALANCED) (c) jacks on the

back of the unit.

8 MAIN OUTPUT VOL knobs

These adjust the output levels of the MAIN OUT-

PUTS 1-2 (UNBALANCED) (f) and MAIN OUT-

PUTS 1-2 (BALANCED) (c) jacks on the back of

the unit.

9 POWER indicator

This shows the status of the unit.

When the POWER (a) switch on the back of the

unit is on, the POWER indicator lights.

0 MONO switch/indicator

When the MONO switch is on (MONO indicator

lit), mono signals will be output from the stereo

output buses (MAIN OUTPUT 1/2, SUB OUTPUT,

MONITOR OUT).

q SUB OUTPUT VOL knob

Use to adjust the output level of the SUB OUTPUT

jacks (x) on the back of the unit.

w MAIN MIC INPUT jack

This is an XLR/TRS combo jack for mic input.

Use the MAIN MIC INPUT VOLUME knob (1) to

set the input level.

e MAIN MIC INPUT EQ knobs

This is a 2-band equalizer (HIGH/LOW) for the mic

input sound.

r INPUTS EQ knobs

Use this 3-band equalizer (HIGH/MID/LOW) to

adjust the sound from the C (MONO) /MIC (h)

input jack or LINE A or B (v) input jacks on the

back of the unit.

t Channel level meters

These indicators show the input levels of input

channels.

10 TASCAM MZ-372

y PFL switches/indicators

o When a PFL switch is on (PFL indicator lit), the

pre-fader signal (signal before fader adjust-

ment) can be monitored through headphones.

o When a PFL switch is off, only the normal

monitoring sound is output.

u MIXING knob

Use this to mix the pre-fader and monitoring

signals output to the headphones.

o Turn all the way to the PFL side to monitor

channels that have their PFL (y) switches

pressed in.

o Turn all the way to the MONITOR side to moni-

tor the monitoring signal.

i PHONES VOLUME knob

Use this to adjust the headphone output level.

o L/R SPLIT switch/indicator

Press to change the headphone output mode.

o When the L/R SPLIT switch is on (indicator

lit), pre-fader signals are output from the left

channel and the monitoring signal is output

from the right channel.

o When the L/R SPLIT switch is off (indicator un-

lit), the monitoring signal is output. When PFL

switches are on, the pre-fader and monitoring

signals are mixed and output together.

NOTE

The PFL signals are mixed with the monitoring sig-

nal, so the selected PFL signals will sound louder.

p PHONES jack

Use this standard stereo jack to connect stereo

headphones.

Use an adapter to connect headphones with a

mini plug.

The monitoring and PFL signals can be monitored,

depending on the PFL (y) and L/R SPLIT (o)

switch settings.

Rear panel

a POWER switch

Press to turn the unit on and off.

When on, the POWER (9) indicator lights on the

front of the unit.

s MONITOR OUT mic mix switch

This sets whether or not the input signal from a

mic connected to the MAIN MIC INPUT (w) jack

on the front of the unit is sent to and mixed with

the monitoring output.

To mix the input signal from a mic connected to

the MAIN MIC INPUT (w) jack with the monitor-

ing output, set the MONITOR OUT mic mix switch

to WITH MIC.

d SUB OUTPUT switch

Set whether the output from the SUB OUTPUT

(x) jacks is stereo or mono.

Set it to MONO for mono output.

f MAIN OUTPUTS 1-2 (UNBALANCED) jacks

These analog outputs are RCA pin jacks.

Use the ATTENUATOR (g) switch to change the

output level.

g ATTENUATOR switches

These switch the output levels from the MAIN

OUTPUTS 1-2 (UNBALANCED) (f) and MAIN

OUTPUTS 1-2 (BALANCED) (c) jacks.

Set them to OFF if the destination amplifier

receives high gain, and set it to ON (-6dB) if the

destination amplifier receives low gain.

TASCAM MZ-372 11

h C (MONO) /MIC input jacks

These are analog XLR input jacks (1: GND, 2: HOT,

3: COLD).

Their input gains can be adjusted using the GAIN

(4) knobs on the front of the unit.

j INPUT LEVEL switches

Use these to set the input levels of the input

sources (mic or line) connected to the C (MONO) /

MIC (h) input jacks.

Set to MIC for mic level signals, and set to LINE for

line level signals.

k LINE/PHONO input selection switches

For channels 2–4, if the output of a CD player or

similar device is connected to a LINE A input (v)

jack, set this to LINE. If a record player output is

connected, set it to PHONO.

l Cord holder

Attach the power cord of the included AC adapter

(TASCAM PS-M1524) here to prevent accidental

disconnection. (See “Attaching the cord” on page

11.)

; DC IN 15V connector

Connect the included AC adapter (TASCAM PS-

M1524) here.

z MONITOR OUT jacks

These RCA pin jacks are analog monitoring

outputs.

x SUB OUTPUT jacks

These RCA pin jacks are analog outputs.

Mono signals will be output if the SUB OUTPUT

(d) switch is set to MONO.

c MAIN OUTPUTS 1-2 (BALANCED) jacks

These analog outputs are XLR jacks. (1: GND, 2:

HOT, 3: COLD)

Use the ATTENUATOR (g) switches to change the

output levels.

v LINE A/B input jacks

These RCA pin jacks are analog line outputs.

Record players can be connected to the LINE A

input jacks of channels 2–4. When connecting

a record player to these jacks, also connect its

grounding wire to the | (GND) jack (b), and set

the LINE/PHONO input selection switch (k) to

PHONO.

b

| (GND) connectors

If a record player is connected to the LINE A input

(v) jacks of channel 2–4, also connect its ground-

ing wire to this.

NOTE

If a humming noise occurs when connecting a

device other than a record player, connecting

a grounding wire from the metal frame of that

device (or the rack frame if rackmounted) to this

could reduce the noise.

Preparation

Connecting the power

Use the included AC adapter (TASCAM PS-M1524) to

connect a power supply to the unit as shown below.

Power outlet

DC plug

TASCAM

PS-M1524 (included)

CAUTION

Always use the AC adapter (TASCAM PS-M1524)

that was packaged with the unit. Using a different

AC adapter could cause malfunction, overheating,

fire or other problems.

NOTE

The AC adapter for the unit includes two types of

adapter cords. Attach the type of AC adapter cord

that matches the power outlet that you are using.

Attaching the cord

In order to prevent the cord from becoming discon-

nected during use, attach it to the cord holder (l)

when connecting it to the unit.

1. Remove the cord holder (l) screw.

2. Place the cord in the cord holder (l).

3. Tighten the cord holder (l) screw.

12 TASCAM MZ-372

Connecting other equipment

This is an example of MZ-372 connections.

Precautions before making connections

0Carefully read the operation manuals of the devices to be connected and then connect them correctly.

0Before making connections, turn this unit and all equipment to be connected off (standby).

0Install all connected devices, including this unit, so that they are powered from the same line. When using a

power strip or similar device, be sure to use one that has high current capacity (thick cable) in order to mini-

mize fluctuations in power voltage.

0When connecting audio devices, minimize the channel 1–6 GAIN (4) knobs and faders (6), and the MAIN

OUTPUT VOL (8), SUB OUTPUT VOL (q) and PHONES VOLUME (i) knobs. Failure to do so could cause

sudden loud noises from monitoring equipment, and this could damage the equipment or harm hearing.

Powered speakers

Headphones

CD player

Record player

Mic Mic

Stereo amplifierStereo amplifier

Examples of connections to an MZ-372

TASCAM MZ-372 13

Connecting microphones

Mics can be connected to the MAIN MIC INPUT (w)

jack on the front of the unit or to one of the channel

1–6 C (MONO) /MIC (h) input jacks on the back of

the unit with the INPUT LEVEL (j) switch set to MIC.

Connecting electronic devices and other

audio equipment

When connecting an electronic device or other audio

equipment, connect it to channel 1–6 C (MONO) /

MIC (h) input jacks, and set the INPUT LEVEL switch

(j) to LINE. The device can be connected to channel

1–6 LINE A or B (v) input jacks.

When connected to channel 2–4 LINE A (v) input

jacks, set the LINE/PHONO (k) input switch to LINE.

NOTE

The C (MONO) /MIC (h) jacks are mono inputs.

Connecting record players

When connecting a record player, connect it to

channel 2–4 LINE A (v) input jacks, and set the LINE/

PHONO (k) input switch to PHONO.

Connect the grounding wire from the record player

to the | (GND) (b) connector.

Connecting monitor speakers

Connect monitor speakers (powered speakers or an

amplifier and speaker system) to the MONITOR OUT

(z) jacks.

To mix in the mic input signal from the MAIN MIC

INPUT (w) jack, and output it from the monitor

speakers, set the MONITOR OUT (s) mic mix switch

to WITH MIC.

Connecting headphones

Connect headphones to the PHONES (p) jack (stan-

dard stereo).

You can monitor input channel pre-fader signals and

the signal before it is sent to the stereo output bus.

CAUTION

Before connecting headphones, minimize the vol-

ume with the PHONES VOLUME (i) knob. Failure

to do so could result in a sudden loud noise that

could harm hearing, for example.

NOTE

Since the headphone sound is output from the

monitoring bus, the position of the MAIN OUT-

PUT VOL (8) knob has no effect on it.

Connecting stereo amplifiers

When connecting a stereo amplifier, connect it to the

MAIN OUTPUTS 1-2 (UNBALANCED) (f) or MAIN

OUTPUTS 1-2 (BALANCED) (c) jacks.

TIP

i When connecting 2 or more amplifier and speaker

systems, including main and sub, main and mon-

itoring, or front and rear combinations, using the

MAIN OUTPUTS 1-2 (UNBALANCED) (f), MAIN

OUTPUTS 1-2 (BALANCED) (c), and SUB OUT-

PUT (x) jacks could be convenient. Moreover, the

outputs of the jacks are independent and have

their own dedicated output knobs, so you can set

the output levels separately with this unit.

i By connecting a recorder to MONITOR OUT

(z) jacks, the signal output to amplifier/speaker

systems can be recorded.

Turning the power on and off

CAUTION

i Turn down the volume of the sound system con-

nected to the unit before starting up or shutting

down the unit.

i Do not wear connected headphones when turn-

ing the unit on and off. Loud noises could damage

the speakers or harm your hearing.

Before turning the power on

1. Make the following settings on the front of the

unit.

o EQ knobs w center values

o Other knobs w all the way left (MIN side)

o Faders w all the way down

o Switches w off (not pushed in)

2. Minimize the output levels of audio sources and

input levels of amplifiers connected to this unit.

Turning the power on

1. Use the POWER (a) switch on the back of the

unit to turn its power on.

The POWER (9) indicator on the front of the unit

will light when on.

2. Turn connected input audio source devices on.

3. Finally turn amplifiers on.

Turning the power off

Follow the procedures above in reverse when turning

the power off.

Failure to follow the correct order could result in

clicking noises, for example, that might damage

equipment.

14 TASCAM MZ-372

Operation procedures

After turning the power on, adjust the levels of the

input signals.

Adjusting mic input channels (1-6)

1. Set the channel 1–6 GAIN (4) and EQ (r) knobs

to their center values.

2. Press the channel 1–6 SOURCE SELECT (5) C/

MIC switches so the C/MIC indicators (2) light.

3. When connecting a mic to a channel 1–6 C

(MONO) /MIC (h) input jack, set the INPUT

LEVEL switch (j) to MIC.

4. Set the MAIN OUTPUT VOL (8) knob levels low.

5. Try speaking into the mic.

Use the channel 1–6 GAIN (4) knob to adjust

the input level so that its level meter (t) lights

around 0 dB.

6. Use the channel 1–6 EQ (r) knobs to adjust the

equalizer.

7. Follow the above procedures for other input

channels with connected mics.

Adjusting line input channels (1-6)

1. Set the channel 1–6 GAIN (4) and EQ (r) knobs

to their center values.

2. When connecting an audio device to channel

1–6, press the SOURCE SELECT switch (5), so

that the SOURCE SELECT indicator (A/B/C/MIC)

lights.

3. When connecting an audio device to a channel

1–6 C (MONO) /MIC (h) input jack, set the

INPUT LEVEL switch (j) to LINE.

When connecting an audio device to channel 1–6

LINE A/B (v) input jacks, set the LINE/PHONE

switch (k) to LINE.

4. Set the MAIN OUTPUT VOL (8) knob levels low.

5. Start playback on the connected audio device.

Use the channel 1–6 GAIN (4) knob to adjust

the input level so that its level meter (t) lights

around 0 dB.

6. Use the channel 1–6 EQ (r) knobs to adjust the

equalizer.

7. Follow the above procedures to adjust other

input channels with connected audio devices.

Adjusting the input of a mic connected

to the MAIN MIC INPUT jack

1. Connect a mic to the MAIN MIC INPUT jack (w),

and press the MAIN MIC (2) switch so the MAIN

MIC (2) indicator lights.

2. Use the MAIN MIC INPUT VOLUME (1) knob to

adjust the mic input level.

3. Use the MAIN MIC INPUT EQ (e) knobs to adjust

the 2-band (HIGH/LOW) equalizer for the mic

sound.

Output channels

Output signals can be sent to the following jacks from

the stereo output bus.

0MAIN OUTPUTS 1-2 (UNBALANCED) (f) and

MAIN OUTPUTS 1-2 (BALANCED) (c) jacks

0SUB OUTPUT (x) jacks

0MONITOR OUT (z) jacks

NOTE

The output level from the MONITOR OUT (z)

jacks cannot be adjusted.

Adjusting the levels output from the MAIN

OUTPUTS 1-2 (UNBALANCED) and MAIN

OUTPUTS 1-2 (BALANCED) jacks

While checking the output level indicators (7), use

the channel faders (6) and MAIN OUTPUT VOL (8)

knobs to adjust the output levels. The optimal output

level adjustment is usually when the output level

indicators (7) light around 0 dB.

When an amplifier is connected to the MAIN OUT-

PUTS 1-2 (UNBALANCED) (f) or MAIN OUTPUTS

1-2 (BALANCED) (c) jacks, set the ATTENUATOR (g)

switch to OFF if it accepts high gain or ON (-6dB) if it

accepts low gain.

Adjusting the level output from the SUB

OUTPUT jacks

Use the SUB OUTPUT VOL (q) knob to adjust the

output level.

If the MONO (0) switch is set to ON (MONO indicator

lit) mono signals will be output from all output jacks.

To output mono signals from only the SUB OUTPUT

(x) jacks, set the SUB OUTPUT (d) switch to MONO.

TASCAM MZ-372 15

Using the talkover function

When the talkover function is turned on by pressing

the TALKOVER (3) switch, the levels of channels 1–6

will be automatically lowered when sound is input

from a mic connected to the MAIN MIC INPUT (w)

jack, making the mic signal easier to hear.

To turn the talkover function off, press the TALKOVER

(3) switch to turn it off (TALKOVER (3) indicator

becomes unlit).

Listening to channel pre-fader signals

By pressing the PFL (y) switches of channels to turn

them on, you can enable headphone monitoring of

individual channels 1–6, even when their faders (6)

are set at minimum values.

You can also monitor the signal before it is sent to the

stereo output bus.

1. Press the PFL (y) switches for the channels you

want to monitor so that their PFL indicators light,

and turn the MIXING (u) knob to PFL.

To monitor the signal before it is sent to the

stereo output bus, turn the MIXING (u) knob to

MONITOR.

2. After making mixing adjustments, use the

PHONES VOLUME (i) knob to adjust the moni-

toring output level.

NOTE

i The L/R SPLIT (o) switch can be turned on/off to

change the headphone output mode.

i When the L/R SPLIT switch (o) is on (indicator

lit), the pre-fader signals are output from the left

channel and the monitoring signal is output from

the right channel.

i When the L/R SPLIT switch (o) is off (indicator

unlit), the pre-fader signals and the monitoring

signal are mixed and output together from both

headphone channels.

i When the PFL (y) switch is off, if the L/R SPLIT

(o) switch is set to on, the monitoring signal

will be output from the right channel and no

sound will be output from the left channel of the

headphones.

Troubleshooting

If you are having trouble with the operation of this

unit, please try the following before seeking repair.

If these measures do not solve the problem, please

contact the store where you purchased this unit or

TASCAM customer support service.

The unit will not turn on.

0Confirm that the AC adapter (TASCAM PS-M1524)

is securely connected to both the outlet and the

DC jack.

Sound is not output from speakers connect-

ed via the MAIN OUTPUTS 1-2 jacks.

0Check the settings and volume of the connected

amplifier.

0Confirm that channel faders (6) are raised.

0Confirm that the input sound source is connected

properly.

The volume is low even when faders are

raised.

0Confirm that the GAIN (4) knobs for channels 1–6

are set properly.

0If mics are being input on channels 1–6, confirm

that the INPUT LEVEL (j) switches are set to

LINE.

The sound is distorted.

0Confirm that the GAIN (4) knobs for channels 1–6

are set properly.

0Confirm that the EQ is not set too high.

0Confirm that the channel 1–6 (6) faders and

MAIN OUTPUT VOL (8) knob are not set too

high.

Sound from a record player is strange.

0Confirm that it is connected to channel 2–4 LINE

A (v) input jacks and the LINE/PHONO (k) input

switch is set to PHONO.

0Confirm that the grounding wire from the record

player is connected to the | (GND) (b) connec-

tor.

A connected device is making a humming

noise.

0Connect a grounding wire from the metal frame

of the connected device to the |(GND) (b)

connector on this unit.

No sound is output from the monitoring sys-

tem connected to the MONITOR OUT jacks.

0Check the settings of the connected monitoring

system.

0Confirm that the channel 1–6 GAIN (4) knobs and

channel faders (6) are raised.

16 TASCAM MZ-372

Specifications

Audio inputs

MAIN MIC INPUT (BALANCED) jacks

Connectors:

XLR-3-31 (1: GND, 2: HOT, 3: COLD)

6.3mm (1/4”) standard TRS jacks (Tip: HOT,

Ring: COLD, Sleeve: GND)

Input impedance: 33 kΩ

Nominal input level: -65 dBu

(VOLUME knob at MAX)

Nominal input level: -30 dBu

(VOLUME knob at MIN)

INPUTS: MIC (BALANCED) jacks

Connectors: XLR-3-31 (1: GND, 2: HOT, 3: COLD)

Set to MIC

Maximum input level: -30 dBu

Minimum input level: -65 dBu

Input impedance: 33 kΩ

Set to LINE (UNBALANCED)

Nominal input level: -1 dBu

Maximum input level: 20 dBu

Input impedance: 22 kΩ

INPUTS: LINE (UNBALANCED) jacks

Connectors: RCA pin jacks

Nominal input level: -10 dBV

Maximum input level: 10 dBV

Input impedance: 22 kΩ

00 dBu=0.775 Vrms, 0 dBV=1 V

Audio outputs

MAIN OUTPUTS (UNBALANCED) jacks

Connectors: RCA pin jacks

Rated output level: -10 dBV

Maximum output level: 10 dBV

Output impedance: 200 Ω

MAIN OUTPUTS (BALANCED) jacks

Connectors: XLR-3-32 (1: GND, 2: HOT, 3: COLD)

Rated output level: 4 dBu

Maximum output level: 24 dBu

Output impedance: 200 Ω

SUB OUTPUT connectors

Connectors: RCA pin jacks

Rated output level: -16 dBV

Maximum output level: 0 dBV

Output impedance: 200 Ω

MONITOR OUT jacks

Connectors: RCA pin jacks

Rated output level: -16 dBV

Maximum output level: 0 dBV

Output impedance: 200 Ω

PHONES jack

Connectors: 6.3mm (1/4”) standard stereo jack

Maximum output: 50 mW + 50 mW

(into 32 Ω load)

00 dBu=0.775 Vrms, 0 dBV=1 V

Audio performance

Frequency response

20 Hz–20 kHz (INPUTS LINE to MAIN OUTPUTS)

Distortion

0.03% or less (INPUTS LINE to MAIN OUTPUTS)

S/N ratio

80 dB or more (INPUTS LINE to MAIN OUTPUTS)

Crosstalk

65 dB or more (INPUTS LINE to MAIN OUTPUTS)

TASCAM MZ-372 17

General

Power

Dedicated AC adapter (TASCAM PS-M1524)

Input voltage: AC 100–240V ~, 50/60Hz

Output voltage: DC 15V

Output current: 2.4 A

Power consumption

35 W

Dimensions

482.0 × 132.0 × 93.2 mm (width × height × depth, including protrusions)

Weight

3.2 kg

Dimensional drawings

462.0mm

482.0mm

76.0mm

120.7mm

18.3mm 63.2mm 11.7m

m

442.2mm

132.0mm

0Illustrations in this manual might differ in part from the actual product.

0Specifications and external appearance might be changed without notification to improve the product.

18 TASCAM MZ-372

Block diagram

TASCAM MZ-372 19

PRÉCAUTIONS DE SÉCURITÉ IMPORTANTES

ATTENTION: POUR RÉDUIRE LE RISQUE D'ÉLECTROCUTION, NE RETIREZ

PAS LE CAPOT (OU L'ARRIÈRE). AUCUNE PIÈCE INTERNE N'EST RÉPARABLE

PAR L'UTILISATEUR. CONFIEZ TOUTE RÉPARATION À UN SERVICE APRÈS-

VENTE QUALIFIÉ.

Le symbole d'éclair à tête de flèche dans un triangle équilatéral sert à

prévenir l'utilisateur de la présence dans l'enceinte du produit d'une «ten-

sion dangereuse» non isolée d'une grandeur suffisante pour constituer

un risque d'électrocution pour les personnes.

Le point d'exclamation dans un triangle équilatéral sert à prévenir

l'utilisateur de la présence d'instructions importantes de fonctionnement

et de maintenance (entretien) dans les documents accompagnant

l'appareil.

AVERTISSEMENT: POUR PRÉVENIR LES RISQUES

D'INCENDIE ET D'ÉLECTROCUTION, N'EXPOSEZ PAS

CET APPAREIL À LA PLUIE NI À L'HUMIDITÉ.

AUX USA/CANADA, UTILISEZ UNIQUEMENT UNE

TENSION D'ALIMENTATION DE 120 V.

Pour le Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME À LA NORME NMB-003 DU CANADA.

Ce produit est conforme aux impératifs

des directives européennes et autres

règlements de la Commission.

Informations sur le marquage CE

EN55103-2

a) Environnement électromagnétique applicable: E1,

E2, E3, E4

INSTRUCTIONS DE SÉCURITÉ IMPORTANTES

1. Lisez ces instructions.

2. Conservez ces instructions.

3. Tenez compte de tous les avertissements.

4. Suivez toutes les instructions.

5. N'utilisez pas cet appareil avec de l'eau à proximité.

6. Nettoyez-le uniquement avec un chiffon sec.

7. Ne bloquez aucune ouverture de ventilation. Instal-

lez-le conformément aux instructions du fabricant.

8. Ne l'installez pas près de sources de chaleur telles

que des radiateurs, bouches de chauffage, poêles

ou autres appareils (y compris des amplificateurs)

dégageant de la chaleur.

9. Ne neutralisez pas la fonction de sécurité de la fiche

polarisée ou de terre. Une fiche polarisée a deux

broches, l'une plus large que l'autre. Une fiche de

terre a deux broches identiques et une troisième

broche pour la mise à la terre. La broche plus large

ou la troisième broche servent à votre sécurité. Si la

fiche fournie n'entre pas dans votre prise, consultez

un électricien pour le remplacement de la prise

obsolète.

10. Évitez de marcher sur le cordon d'alimentation et

de le pincer, en particulier au niveau des fiches, des

prises secteur, et du point de sortie de l'appareil.

11. N'utilisez que des fixations/accessoires spécifiés par

le fabricant.

MODE D'EMPLOI

20 TASCAM MZ-372

12. Utilisez-le uniquement avec le chariot, socle, trépied,

support ou table spécifié par le fabricant ou vendu

avec l'appareil. Si un chariot est utilisé, faites atten-

tion à ne pas être blessé par un renversement lors du

déplacement de l'ensemble chariot/appareil.

13. Débranchez cet appareil en cas d'orage ou de non

utilisation prolongée.

14. Confiez toute réparation à des techniciens

de maintenance qualifiés. Une réparation est

nécessaire si l'appareil a été endommagé d'une

quelconque façon, par exemple si le cordon ou

la fiche d'alimentation est endommagé, si du li-

quide a été renversé sur l'appareil ou si des objets

sont tombés dedans, si l'appareil a été exposé

à la pluie ou à l'humidité, s'il ne fonctionne pas

normalement, ou s'il est tombé.

0La fiche secteur est utilisée comme dispositif de dé-

connexion et doit donc toujours rester disponible.

0Des précautions doivent être prises en cas d'utilisa-

tion d'écouteurs ou d'un casque avec le produit car

une pression sonore excessive (volume trop fort) dans

les écouteurs ou dans le casque peut causer une perte

auditive.

0Si vous rencontrez des problèmes avec ce produit,

contactez TEAC pour une assistance technique.

N'utilisez pas le produit tant qu'il n'a pas été réparé.

0Ne retirez pas les capots externes ou boîtiers pour

exposer l’électronique. aucune pièce interne n’est

réparable par l’utilisateur.

0Si vous rencontrez des problèmes avec ce produit,

contactez le magasin où vous avez acheté l’unité.

n’utilisez pas le produit tant qu’il n’a pas été réparé.

0L’utilisation de commandes, de réglages ou le suivi

de procédures autres que ce qui est décrit dans ce

document peut provoquer une exposition à un rayon-

nement dangereux.

ATTENTION

0N'exposez pas cet appareil aux gouttes ni aux

éclaboussures.

0Ne placez pas d'objet rempli de liquide sur l'appa-

reil, comme par exemple un vase.

0N’installez pas cet appareil dans un espace confiné

comme une bibliothèque ou un meuble similaire.

0L’appareil doit être placé suffisamment près de

la prise de courant pour que vous puissiez à tout

moment attraper facilement la fiche du cordon

d'alimentation.

0Si le produit utilise des piles/batteries (y compris

un pack de batteries ou des batteries fixes), elles ne

doivent pas être exposées au soleil, au feu ou à une

chaleur excessive.

0PRÉCAUTION pour les produits qui utilisent des

batteries remplaçables au lithium: remplacer une

batterie par un modèle incorrect entraîne un risque

d'explosion. Remplacez-les uniquement par un

type identique ou équivalent.

MONTAGE EN RACK DE L'UNITÉ

Utilisez le kit de montage en rack pour monter l'unité

dans un rack 19" standard, comme représenté ci-dessous.

ATTENTION

i Laissez 1U d'espace au-dessus de l'unité pour la

ventilation.

i Laissez au moins 10 cm à l'arrière de l'unité pour la

ventilation.

ページが読み込まれています...

Tascam MZ-372 取扱説明書

Tascam MZ-372 取扱説明書

他の言語で

関連論文

その他のドキュメント