Supermicro MicroBlade MBM-XEM-001 ユーザーマニュアル

MicroBlade

®

Network Modules

User’s Manual

Revison 1.0a

MBM-GEM-001 2.5-Gbps/1 Gbps

Ethernet Switch Module

MBM-GEM-003s 2.5-Gbps/1 Gbps

Ethernet Switch Module

MBM-GEM-003i 2.5-Gbps/1 Gbps

Ethernet Switch Module

MicroBlade Network Modules User’s Manual

ii

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The

vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no

commitment to update or to keep current the information in this manual, or to notify any person or

organization of the updates. Please Note: For the most up-to-date version of this manual, please see

our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described

in this manual at any time and without notice. This product, including software and documentation, is the

property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction

of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE

THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,

SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF

REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,

SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara

County in the State of California, USA.. The State of California, County of Santa Clara shall be the

exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not

exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer’s instruction manual, may cause harmful interference with radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference,

in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning

applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further

details.

Manual Revison 1.0a

Release Date: October 24, 2014

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy

any part of this document.

Information in this document is subject to change without notice. Other products and companies referred

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Printed in the United States of America

WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS

PRODUCT MAY EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER

REPRODUCTIVE HARM.

iii

Preface

About this Manual

This manual is written for professional system integrators, Information Technology

professionals, service personnel and technicians. It provides information for the

installation and use of Supermicro's network modules. Installation and maintenance

should be performed by experienced professionals only.

Manual Organization

Chapter 1: Introduction

The first chapter provides an overview of this manual.

Chapter 2: System Safety

You should familiarize yourself with this chapter for a general overview of safety

precautions that should be followed when installing and servicing MicroBlade Network

Modules.

Chapter 3: Setup and Installation

Refer here for details on installing the modules into a MicroBlade enclosure and for their

setup and configuration.

Chapter 4: Ethernet Modules

This chapter details all Ethernet switches for the MicroBlade system.

Appendix A: LED Descriptions

LED descriptions are summarized here in this appendix for quick reference.

MicroBlade Network Modules User’s Manual

iv

Notes

v

Table of Contents

Chapter 1 Introduction.......................................................................1-1

1-1 Overview.............................................................................................1-1

1-2 Product Checklist of Typical Components.....................................1-1

1-3 Features..............................................................................................1-1

1-4 Contacting Supermicro.....................................................................1-2

Chapter 2 Standardized Warning Statements.....................2-1

2-1 About Standardized Warning Statements......................................2-1

Warning Definition...................................................................................2-1

Installation Instructions ...........................................................................2-3

Circuit Breaker........................................................................................2-4

Power Disconnection Warning................................................................2-5

Equipment Installation.............................................................................2-6

Restricted Area.......................................................................................2-7

Battery Handling .....................................................................................2-9

Redundant Power Supplies ..................................................................2-10

Backplane Voltage................................................................................2-11

Comply with Local and National Electrical Codes.................................2-12

Product Disposal...................................................................................2-13

Hot Swap Fan Warning.........................................................................2-14

Power Cable and AC Adapter ..............................................................2-15

Chapter 3 Setup and Installation.................................................3-1

3-1 Installing/Removing a Switch Module............................................3-1

Installing a Switch Module ......................................................................3-1

Removing a Switch Module ....................................................................3-2

3-2 Configuring the Switch Module.......................................................3-3

Web-based Management Utility/IPMI .....................................................3-4

Network Connection.............................................................................3-4

Address Defaults..................................................................................3-6

3-3 Locating and Identifying Switches and Switch Ports

on a Blade Enclosure

..............................................................................3-7

Locating and Identifying a Switch on a Blade Enclosure........................3-7

Locating and Identifying a Switch Port on a Blade Enclosure.................3-7

MicroBlade Network Modules User’s Manual

vi

Chapter 4 Ethernet Modules..........................................................4-1

4-1 MBM-GEM-001 Gigabit Ethernet Switch Module.........................4-1

LED Indicators ........................................................................................4-2

Ports........................................................................................................4-2

4-2 MBM-GEM-003i Gigabit Ethernet Switch Module........................4-3

LED Indicators ........................................................................................4-4

Ports........................................................................................................4-4

4-3 MBM-GEM-003s Gigabit Ethernet Switch Module.......................4-5

LED Indicators ........................................................................................4-6

Ports........................................................................................................4-6

Appendix A LED Descriptions......................................................A-1

A-1 MBM-GEM-001 Gigabit Ethernet Module LED Descriptions.....A-1

A-2 MBM-GEM-003i Gigabit Ethernet Module LED Descriptions....A-2

A-3 MBM-GEM-003s Gigabit Ethernet Module LED Descriptions...A-3

vii

List of Figures

Figure 3-1. Installing a Switch Module..............................................................3-1

Figure 3-2. Blade Enclosure with Switch Modules Installed..............................3-2

Figure 3-3. Configuring the Switch Module.......................................................3-3

Figure 3-4. Blade Status Screen.......................................................................3-4

Figure 3-5. Blade System Screen.....................................................................3-5

Figure 3-6. Gigabit Switch Panel.......................................................................3-5

Figure 4-1. MBM-GEM-001 Gigabit Ethernet Switch Module ...........................4-1

Figure 4-2. MBM-GEM-003i Gigabit Ethernet Switch Module...........................4-3

Figure 4-3. MBM-GEM-003s Gigabit Ethernet Switch Module..........................4-5

MicroBlade Network Modules User’s Manual

viii

Notes

v

List of Tables

Table 3-1. MBM-GEM-001 Switch Module Address Default Settings...............3-6

Table 3-2. Locating and Identifying a Switch ....................................................3-7

Table 3-3. MBE-628L Enclosures with MicroBlade Switches ...........................3-8

Table 4-1. MBM-GEM-001 Gigabit Ethernet Switch Module Interface..............4-1

Table 4-2. MBM-GEM-001 Gigabit Ethernet Switch Module Features .............4-2

Table 4-3. MBM-GEM-001 Gigabit Ethernet Switch Module Ports...................4-2

Table 4-4. MBM-GEM-003i Gigabit Ethernet Switch Module Interface.............4-3

Table 4-5. MBM-GEM-003i Gigabit Ethernet Switch Module Features.............4-4

Table 4-6. MBM-GEM-003i Gigabit Ethernet Switch Module Ports ..................4-4

Table 4-7. MBM-GEM-003s Gigabit Ethernet Switch Module Interface............4-5

Table 4-8. MBM-GEM-003s Gigabit Ethernet Switch Module Features............4-6

Table 4-9. MBM-GEM-003s Gigabit Ethernet Switch Module Ports .................4-6

Table A-1. MBM-GEM-001 Gigabit Ethernet Switch LED Indicators ................A-1

Table A-2. MBM-GEM-003i Gigabit Ethernet Switch LED Indicators................A-2

Table A-3. MBM-GEM-003s Gigabit Ethernet Switch LED Indicators...............A-3

MicroBlade Network Modules User’s Manual

vi

Notes

1-1

Chapter 1

Introduction

1-1 Overview

The MicroBlade Network Modules User’s Manual contains information on all network

modules used for the Supermicro MicroBlade system. This incorporates information on

the Ethernet switch module for Ethernet.

1-2 Product Checklist of Typical Components

All modules are shipped alone or with a MicroBlade enclosure when ordered. Aside from

packaging, no cables or cords are included.

Please refer to our web site for information on operating systems that have been

certified for use with the MicroBlade (www.supermicro.com/products/MicroBlade/).

Note: For your system to work properly, please follow the links below to download all

necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information: http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

support@supermicor.com

Note: A complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm.

1-3 Features

See Chapter 4: "Ethernet Modules" on page 4-1 for information on all Ethernet

switches.Gigabit Ethernet switch module

MicroBlade Network Modules User’s Manual

1-2

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email:

[email protected] (General Information)

[email protected] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

‘s-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Website:

www.supermicro.nl

Email:

[email protected]l (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Pacific

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3992

Website: www.supermicro.com.tw

Technical Support:

Email: [email protected]

2-1

Chapter 2

Standardized Warning Statements

2-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of

situations which have the potential for bodily injury. Should you have questions or

experience difficulty, contact Supermicro's Technical Support department for assistance.

Only certified technicians should attempt to install or configure components.

Read this appendix in its entirety before installing or configuring components in the

Supermicro chassis

These warnings may also be found on our web site at http://

www.supermicro.com/about/policies/safety_information.cfm.

Warning Definition

Warning!

This warning symbol means danger. You are in a situation that could cause

bodily injury. Before you work on any equipment, be aware of the hazards

involved with electrical circuitry and be familiar with standard practices for preventing

accidents.

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意识到

触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的声明号码

找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸電的危

險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關的

翻譯說明內容。

MicroBlade Network Modules User’s Manual

2-2

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren

elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen

vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen

Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de

manipular cualquier equipo, considere los riesgos de la corriente eléctrica y

familiarícese con los procedimientos estándar de prevención de accidentes. Al final de

cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en

el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation

pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un

équipement, soyez conscient des dangers liés aux circuits électriques et

familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.

Pour prendre connaissance des traductions des avertissements figurant dans les

consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro

de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא

. ﻲﻓ ﻚﻧا نأ ﻦﻜﻤﯾ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻا ﺔﯾﺪﺴﺟ ﺰﻣﺮﻟا اﺬھ ﻲﻨﻌﯾ ﺮﻄﺧ !ﺮﯾﺬﺤﺗ

نأ ﻞﺒﻗ يأ ﻰﻠﻋ ﻞﻤﻌﺗ تاﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟا ﺮطﺎﺨﻤﻟﺎﺑ ﺮﺋاوﺪﻟا

ﺔﯿﺋﺎﺑﺮﮭﻜﻟا

ﻛوﺔﯾارد ﻰﻠﻋ ﻦ رﺎﻤﻤﻟﺎﺑتﺎﺳ ﺔﯿﺋﺎﻗﻮﻟا ﻟ ﻊﻨﻤعﻮﻗو يأثداﻮﺣ

ﻢﻗر مﺪﺨﺘﺳا نﺎﯿﺒﻟا صﻮﺼﻨﻤﻟا ﺔﯾﺎﮭﻧ ﻲﻓ ﺮﯾﺬﺤﺗ ﻞﻛ رﻮﺜﻌﻠﻟ ﺎﮭﺘﻤﺟﺮﺗ

2-3

Chapter 2: Standardized Warning Statements

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die lichamelijk

letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich

bewust te zijn van de bij een elektrische installatie betrokken risico's en dient u op de

hoogte te zijn van de standaard procedures om ongelukken te voorkomen. Gebruik de

nummers aan het eind van elke waarschuwing om deze te herleiden naar de

desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power

source.

警告

将此系统连接电源前 , 请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

MicroBlade Network Modules User’s Manual

2-4

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 250 V,

20 A.

警告

此产品的短路 ( 过载电流 ) 保护由建筑物的供电系统提供 , 确保短路保护设备的额定电流

不大于 250V,20A。

警告

此產品的短路 ( 過載電流 ) 保護由建築物的供電系統提供 , 確保短路保護設備的額定電

流不大於 250V,20A。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw.

Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der

Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del

edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250 V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend

de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de

protection n'est pas supérieur à :250 V, 20 A.

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

ﻟا تادﺎﺷرإ ﺮﻗاﺐﯿﻛﺮﺘ ﻞﯿﺻﻮﺗ ﻞﺒﻗ ﻰﻟإ مﺎﻈﻨﻟا ﺔﻗﺎﻄﻠﻟ رﺪﺼﻣ

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

2-5

Chapter 2: Standardized Warning Statements

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische

installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan

220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power

cord removed from the power supply module(s) before accessing the chassis

interior to install or remove system components.

警告

在你打开机箱并安装或移除内部器件前 , 必须将系统完全断电 , 并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt

sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den

Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu

entfernen.

ﺞﺘﻨﻤﻟا اﺬھ ﻰﻠﻋ ﺪﻤﺘﻌﯾ تاﺪﻌﻣ ﺔﯾﺎﻤﺤﻟا ةﺮﯿﺼﻘﻟاﺮﺋاوﺪﻟا ﻦﻣ ﺎﮭﺘﯿﺒﺜﺗ ﻢﺗ ﻲﺘﻟا ﻲﻓ

ﻰﻨﺒﻤﻟا

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ نأ ﻢﯿﯿﻘﺗ زﺎﮭﺠﻟا ﻟاﻲﺋﺎﻗﻮ ﺲﯿﻟ ﻦﻣ ﺮﺜﻛأ

MicroBlade Network Modules User’s Manual

2-6

¡Advertencia!

El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico

quitado de los módulos de fuente de alimentación antes de tener acceso el interior del

chasis para instalar o para quitar componentes de sistema.

Attention

Le système doit être débranché de toutes les sources de puissance ainsi que de son

cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou

enlever des composants de systéme.

Waarschuwing

Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of

verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle

stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen.

Equipment Installation

Warning!

Only trained and qualified personnel should be allowed to install, replace, or

service this equipment.

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

יילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﯾ مﺎﻈﻨﻟا ﻊﯿﻤﺟ ﻦﻣردﺎﺼﻣ ﺔﻗﺎﻄﻟا ﺔﻟازإو ءﺎﺑﺮﮭﻜﻟا ﻚﻠﺳ ﻦﻣ ةﺪﺣو داﺪﻣا

ﺔﻗﺎﻄﻟا ﻞﺒﻗ

ﻰﻟإ لﻮﺻﻮﻟا ﺔﯿﻠﺧاﺪﻟا ﻖطﺎﻨﻤﻟا ﻟﻞﻜﯿﮭﻠ ﺔﻟازإ وأ ﺖﯿﺒﺜﺘﻟ تﺎﻧﻮﻜﻣ زﺎﮭﺠﻟا

2-7

Chapter 2: Standardized Warning Statements

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualifiziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la maintenance

de ces équipements à des personnels qualifiés et expérimentés.

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwalificeerd personeel.

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted

access area can be accessed only through the use of a special tool, lock and

key, or other means of security. (This warning does not apply to workstations).

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥匙或

其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或其

他安全方式才能進入的區域。

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﯿﺑرﺪﻤﻟاو و ﺐﯿﻛﺮﺘﻟلاﺪﺒﺘﺳا وأ ﺔﻣﺪﺧ زﺎﮭﺠﻟا اﺬھ ﺢﻤﺴﯾ نأ ﺐﺠﯾ ﻂﻘﻓ ﻦﯿﻠھﺆﻤﻟا ﻦﯿﻔظﻮﻤﻠﻟ

MicroBlade Network Modules User’s Manual

2-8

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der

Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und

Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo

puede obtenerse acceso a una de estas áreas mediante la utilización de una

herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone

d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de

verrouillage et une clé, ou tout autre moyen de sécurité.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang

tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van

speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

תתלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﯿﺼﺨﺗ ةﺪﺣﻮﻟا هﺬھ ﻲﻓ ﺎﮭﺒﯿﻛﺮﺘﻟ ﻖطﺎﻨﻣ ةرﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟا ﻦﻜﻤﯾﻰﻟإ لﻮ ﺔﻘﻄﻨﻣ ةرﻮﻈﺤﻣ ﻂﻘﻓ ماﺪﺨﺘﺳا لﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ةادأ

وأ يأ ﻼﻟ ىﺮﺧأ ﺔﻠﯿﺳونﺎﻣﻷ حﺎﺘﻔﻣو ﻞﻔﻗ

ページが読み込まれています...

Supermicro MicroBlade MBM-XEM-001 ユーザーマニュアル

このマニュアルも適しています

Supermicro MicroBlade MBM-XEM-001 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント