TABLE OF CONTENTS
CAUTIONS ON USE. . . . . . . . . . . . . . . . . . . . . . . . .4
CAUTIONS ON HANDLE . . . . . . . . . . . . . . . . . . . . .5
NOTE FOR OUTLOOKING FINISH . . . . . . . . . . . . .5
MODEL NAME OF SPEAKER SYSTEM . . . . . . . . .5
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
CAUTIONS ON INSTALLATION . . . . . . . . . . . . .7 ~ 9
CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . .10~11
REMOVING THE GRILLE NET. . . . . . . . . . . . . . . .12
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . .13
Read this manual carefully to ensure that you take full
advantage of all this unit has to offer.
Keep the manual for future reference should any doubts
or problems arise.
https://manual-hub.com/
https://manual-hub.com/
https://manual-hub.com/
• Avoid placing the speaker systems in places exposed to
direct sunlight for long periods of time or near heaters or
other heating equipment.
• Placing in humid or dusty places may result in damage.
• Exposing the cabinet to insecticides or wiping it with ben-
zene, thinner or other solvents may result in damage or
discoloration to the finish. Use a soft cloth or wiping cloth
included to wipe any dirt off the cabinet. Use cloths con-
taining chemical substances with care.
• Do not apply inputs exceeding the speaker system's max.
input (the input which can be applied a short period of time
with regular program sources).
• The output terminals may differ depending on the amplifier
being used. Consult the amplifier's instructions.
• Clipping or other problems may occur in the output wave-
form when using the speaker systems with a high output
and the amplifier's tone controls set to the maximum.
Avoid using them under these conditions.
• Never play such special signals as a tape recorder's fast-
forwarding signals or sine waves continuously.
• When moving the speaker systems, be careful not to
apply excess force to the speaker nets. Doing so could
damage the speaker units.
CAUTIONS ON USE
https://manual-hub.com/
WARNING
• In case of ceiling or wall installing, please
ask a specialist to make it safely.
• Fix cord to prevent being caught on it that might make
loudspeakers fall down.
• Please check and confirm again after the loudspeaker
would have been installed. Do not forget a periodical
inspection also. DENON does not take any responsibility
for any accident caused by unsteady installing.
CAUTION
• The speaker systems are finished by using natural ply
wood and sprayed. Please note that the colour and the
grain deviate and differ at every unit.
CAUTIONS ON HANDLE
NOTE FOR OUTLOOKING FINISH
MODEL NAME OF SPEAKER SYSTEM
https://manual-hub.com/
• Check that the following parts are included in the package
aside from the main unit:
Speaker system (SC-C33XG)
Cord (approx. 3m) . . . . . . . . . . . . . . . . . . . . . . . . . 1
Anti-slip pad (4pcs./1sheet) . . . . . . . . . . . . . . . . . . 2
Wiping cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating instructions (this book) . . . . . . . . . . . . . 1
Denon service network. . . . . . . . . . . . . . . . . . . . . . 1
Speaker system (SC-T33XG SC-A33XG)
Cord
(approx.SC-T33XG: 3m,SC-A33XG: 10m) . . . . . . 1
Anti-slip pad (4pcs./1sheet) . . . . . . . . . . . . . . . . . . 1
Wiping cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Operating instructions (this book) . . . . . . . . . . . . . 1
Denon service network. . . . . . . . . . . . . . . . . . . . . . 1
ACCESSORIES
1
2
3
4
5
1
2
3
4
5
SC-C33XG
SC-T33XG/SC-A33XG
CAUTION
• As an aid to better understanding the operation method,
the illustrations used in this manual may slightly differ
from the actual set.
https://manual-hub.com/
The tone character produced by speaker systems
depends on such factors as the size and type of room,
the method of installation, etc. Pay attention to the fol-
lowing points when installing the speaker systems.
• If the bass sound is overemphasized when the speaker
systems are installed directly on the floor, set them on
concrete blocks or other hard stands.
• Note that howling may be produced if the speaker sys-
tems are placed on the same stand or shelf as a record
player.
• If there are walls or glass doors behind or in front of the
speaker systems, use heavy curtains, etc., to prevent res-
onance and reflection.
• This is a low leakage flux type speaker system which can
be used near television sets, etc., but with some TV sets
the colors may become blotchy. If this happens, turn off
the TV's power, wait 15 to 30 minutes, and turn the power
back on. The TV's self demagnetizing circuit will improve
the picture. If the colors are still blotchy, move the speaker
systems further away from the TV.
• Also note that if there is a magnet or any device generat-
ing magnetic force nearby, interaction between this device
and the speaker systems can cause the colors on the TV
to become blotchy.
WARNING
• For your safety, do not put anything nor lean
yourself on the loudspeakers.
• Do not push the loudspeaker from aside to protect it from
topping that may cause serious accident.
• Fix cord to prevent being caught on it and making loud-
speakers topping down.
Speaker system (SC-A33XG)
• When setting on a shelf, etc., attach the four included anti-
slip pads (pieces of cork 1 mm thick) to the bottom.
(Refer to diagram below.)
(When mounting on a stand or brackets)
The speaker system (SC-A33XG) can be mounted to a
separately sold floor-mount stand (ASS-100,80) using the
screw holes on the bottom (60 mm intervals) or to a ceiling
suspension bracket (ASG-10/20) using the screw holes on
the back (60 mm intervals). When mounting on a stand or
bracket, follow the instructions included with the bracket or
stand and be very careful to mount the speaker system
securely.(See diagram above.)
CAUTIONS ON INSTALLATION
Screw holes
Floor-mount stand (ASS-100,80) /
Ceiling suspension bracket (ASG-10/20)
Anti-slip pad
Bottom view
Anti-slip pad
https://manual-hub.com/
(When mounting on a wall)
The wall mount hooks on the rear panel of the speaker
system (SC-A33XG) can be used to mount the speaker
system on the wall. When doing so, insert the heads of
screws, etc., into the holes in the wall mount hooks. (Refer
to above figure.) Mount on a solid wall strong enough to
withstand the weight of the speaker. Note that Denon will
not be held responsible for any injuries or accidents due to
the speaker falling.
Speaker system (SC-C33XG)
• The front panel of the speaker system (SC-C33XG) is at a
slant, designed so it can face upwards or downwards
depending on where it is installed.
We recommend installing with the front panel facing down-
wards when placing the speaker system in a position
above the ears, facing upwards when placing the speaker
system on the floor. Set the direction of the saran net
according to the direction of the front panel.
When installed facing down
Affix the four included anti-slip pads (approx. 1 mm thick)
to the surface in contact with the shelf, etc. (the side with
the smaller surface).
(Refer to diagram below.)
Wall mount hook
Rear elevation
Screw holes
/Ceiling suspension bracket (ASG-10/20)
Speaker system (SC-C33XG)
The example of installation
Facing down
Speaker system (SC-C33XG)
Facing up
Anti-slip pad Anti-slip pad
Anti-slip pad
https://manual-hub.com/
When installed facing up
Affix the four included anti-slip pads (approx. 1 mm thick)
to the surface in contact with the floor etc. (the side with
the larger surface).
(Refer to diagram below.)
Speaker system (SC-T33XG)
• When using the speaker system on a slippery surface (for
example on tiles or a smooth wooden floor), attach the
four included anti-slip pads (pieces of cork 1 mm thick) to
the bottom. (Refer to diagram below.)
(Mounting on the base )
The speaker system (SC-T33XG) can be mounted to a
separately sold base (ASF-T33) using the four screw holes
on the bottom. When doing so, follow the instructions
included with the base and be very careful to mount the
speaker system securely.
When mounting the base (ASF-T33), affix the four
included anti-slip pads (pieces of cork 1 mm thick) to
four places on the bottom of the set (between the base
(ASF-T33) and the set).
Anti-slip pad Anti-slip pad
Anti-slip pad
Anti-slip pad
Base (ASF-T33)
Screw holes
Anti-slip pad
https://manual-hub.com/
Before connecting, please consult with the instructions of
your amplifier and follow them also.
Be sure to turn the amplifier's power off when connect-
ing the speaker systems.
• Use the included cables to connect the input terminals on
the back of the speaker systems (see diagram) to the
amplifier's speaker output terminals.
• Connect the speaker system for the left channel amplifier's
"L" terminals, the one for the right channel to the ampli-
fier's "R" terminals, matching the polarities (" " and " "
marks).
• Inverting the polarities will result in unnatural sound, with
the phase off or no low bass sound. Also check that all
two terminal knobs are tightly fastened.
Connecting the speaker terminals
1. Peel off the sheath from the tip of the connection cord,
then firmly twist the wires by hand so that they do not
stick out and cause short-circuits.
2.Loosen the terminal by turning it counterclockwise, then
insert the connection cord into the hole in the speaker
terminal.
3. Turn the terminal clockwise to tighten it.
Check that none of the core wires are sticking out of the
hole.
Once the connections are com-
pletely, gently pull on the
speaker cords to make sure they
are securely connected.
CONNECTIONS
1Sheath
3
2
https://manual-hub.com/
1.Speaker system (SC-A33XG/SC-C33XG)
• Use the included cables to connect the input terminals on
the back of the speaker systems (see diagram) to the
amplifier's speaker output terminals.
2. Speaker system (SC-T33XG)
For normal use
• Use the included cables to connect the input terminals on
the back of the speaker systems (see diagram) to the
amplifier's speaker output terminals.
(Bi-wiring Connections)
These speaker systems are equipped with input terminals
allowing bi-wiring, so two speaker cords can be used for
even greater sound. (A network circuit is included, so there
is no need for a channel divider.)
• First prepare two speaker cords. (When bi-wiring, we rec-
ommend using cords with excellent transfer characteris-
tics.)
• The top set of input terminals are for the tweeter and
super tweeter, the bottom set for the woofer. First loosen
all the knobs, remove both short-circuit plates, then con-
nect the speaker cords to the respective terminals. (See
diagram below.) Be sure to remove both short-circuit
plates. Twist the other ends (the sides to be connected to
the amplifier) of the two cords for the " " side (red)
together, and do the same for the two cords for the " "
side (black).
• If your amplifier has two sets of speaker outputs (A and B),
the tweeter and squawker can be connected to set A, the
woofer to set B (or vice versa). If this is done, set the
amplifier's speaker selector switch to the "A+B" position. If
the amplifier does not have an "A+B" position (in other
words, if it is not equipped to play the two sets of speakers
simultaneously), twist the ends of the two cords together
See below and connect them to either the A or B speaker
terminals.
Connections . . . The red terminals are the " " terminals, the
black ones on the left side the " " terminals.
Connect to amplifier's " "
side. (Copper color)
Connect to amplifier's " " side. (Silver color)
NOTE : Make sure the core wires do not touth each other.
Loosen the terminal knobs,
insert the cables' core wires,
then tighten the konobs.
Connections . . . . . The red terminals on the right side are the"
" terminals, the black ones on the left side the
"" terminals.
For normal use
Loosen the terminal knobs and
insert the short-circuit plates.
Loosen the terminal knobs, insert the
cords' core wires, then tighten the
konobs.
Connect to ampli-
fier's " " side.
(Copper color)
Connect to ampli-
fier's " " side.
(Silver color)
NOTE : Make sure the core wires do not touth each other.
Short-circuit
plate
Red terminal
Black terminal
https://manual-hub.com/
• Finally, check that all connections are correct (" " and "
" sides, left and right channels) on both the amplifier and
the speaker systems, and that all the knobs are tight and
the cords securely fastened.
• The overall impedance of these speaker systems is 6
ohms, so bi-wiring is possible as long as your amplifier's
applicable load impedance is 6 ohms or less. (Tweeter/
Super tweeter:6, Woofer terminals:6 )
• The net on the front of the speaker system is detachable.
• To remove it, grasp it on both sides and pull it towards you.
• To attach the net, line up the plastic holes of the net with
the pegs on the cabinet and press in.
• Use a wiping cloth attached and wipe lightly to remove dirt
from the cabinet and operation panel.
When using chemically treated cloths, follow the precau-
tions that have been written for them.
• Do not use benzene, thinners, or other organic solvents or
insecticides on the main unit since they may cause a
change in quality or color.
Connect to amplifier's ""
side.(Copper color)
Connect to amplifier's " "
side. (Silver color)
Tighten the knobs
securely.
Short-circuit plate
Set the amplifier's
speaker selector switch
to the "A+B" position.
Woofer terminals
Tweeter /
Super tweete
r
Connect to amplifier's A
speaker " " side.
Connect to amplifier's A
speaker " " side.
Connect to amplifier's B
speaker " " side.
Connect to amplifier's B
speaker " " side.
Connections for Bi-wiring
NOTE: Be sure to remove the short-circuit plates first.
• For amplifiers with no "A+B" posision
Woofer terminals
• For amplifiers with no "A+B" posision
Tweeter /
Super tweeter
REMOVING THE GRILLE NET
CLEANING
https://manual-hub.com/
• SC-A33XG
Type : 2-way, 2-speakers
Closed box / Low-leakage-flux
Speakers : 12cm cone bass-mid 1
Super-high range 1
Input impedance : 6 /ohms
Max. input : 80 watts (IEC), 160 watts (PEAK)
Frequency range : 80 Hz~90 kHz
Crossover frequency: Approx.4kHz
Sensitivity : 86 dB (1watt・1m)
Dimensions : 140(W) 230(H) 153(D)mm
Mass : 2.0 kg
• SC-C33XG
Type : 2-way, 5-speakers
Reflex box / Low-leakage-flux
Speakers : 5.7 cm cone bass-mid 4
Super-high range 1
Input impedance : 6 /ohms
Max. input : 80 watts (IEC), 160 watts (PEAK)
Frequency range : 60 Hz~90 kHz
Crossover frequency: Approx.4kHz
Sensitivity : 86 dB (1watt・1m)
Dimensions : 390(W) 75(H) 187(D)mm
Mass : 2.2 kg
•SC-T33XG
Type : 3-way, 4-speakers
Reflex box / Low-leakage-flux
Speakers : 12 cm cone bass-mid 2
High range (2.5cm Dome 1)
Super-high range 1
Input impedance : 6 /ohms
Max. input : 100 watts (IEC), 200 watts (PEAK)
Frequency range : 40 Hz~90 kHz
Crossover frequency: Approx.4kHz
Sensitivity : 89 dB (1watt・1m)
Dimensions : 170(W) 920(H) 240(D)mm
Mass : 12.4 kg
For improvement purposes, specifications and design
are subject to change without notice.
SPECIFICATIONS
https://manual-hub.com/
https://manual-hub.com/
https://manual-hub.com/
https://manual-hub.com/
/