Yealink Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2 クイックスタートガイド

ブランド: Yealink

モデル: Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2

タイプ: クイックスタートガイド

USB Video Conferencing Endpoint

Quick Start Guide(V1.2)

www.yealink.com

English | 简体中文

UVC40

AAA Battery×2UVC 40

VCR20

Remote Control

Cable Tie×5

Quick Start Guide

We recommend that you use the accessories provided or approved by Yealink. The use of

unapproved third-party accessories may result in reduced performance.

Use the Yealink original power adapter (48V/0.7A) to charge the endpoint only. The use of the

third-party power adapter may cause the damage to the endpoint.

The USB cable in the MVC400/ZVC400 package is 2.5 meters long.

Mounting Bracket

and Accessories

Power Adapter

×4

×2

Silicone Pad×2

Put on a Flat Surface

Package Contents

USB Cable

TV TV

UVC40 Installation

Wall Mounting

Use the bracket to mount your endpoint on a wall. The mounting height affects your

camera view. The recommended height is 1.1m above the ground.

Placing UVC40

Mount the UVC40 below the TV when

the mounting height of the TV is higher than

120cm.

Mount the UVC40 above the TV when

the mounting height of the TV is lower

than 120cm.

Step1：Assemble the mounting bracket

Mount on a Wall

10cm

H>120cm

H<120cm

Hole depth: 30mm

Hole diameter: 6mm

118mm

T4×30 screws

15°

Step2：Mount the UVC40 to the wall

Adjusting the Camera Tilt

Remote Control Installation Cable Ties Installation

Remote Control and Cable Ties Installation

Hardware Interface Instructions

Line In: connect a 3.5mm audio connector to use the UVC40 as an audio output device.

USB: come ready for the future connection of DD10 to connect to CPW90.

Video Out: connect to a PC as video output.

Microphone: connect to the microphone (for exmaple, VCM34).

DC48V: connect to the power adapter.

Reset: reset the UVC40 to factory defaults.

Security slot: connect a universal security cable to the UVC40 so that you can

lock the UVC40 down.

Pairing key: press the pairing key to pair the CPW90 wireless microphone.

UVC40 Connection

LED Indicator Instructions

LED indicators on the UVC40:

LED Status

Description

Off

Flashing green

The UVC40 is not properly connected to the mini-PC.

Solid green

Flashing orange The UVC40 is upgrading firmware.

There is an incoming call.

The UVC40 is in recovery mode and the firmware has not been

upgraded.

The UVC40 is active.

Flashing red

Solid red The UVC40 is muted.

Flashing red and

green alternately

The UVC40 is paired with the CPW90.

The UVC40 is initializing or in sleep mode.Solid orange

The cable should be replaced at once if its skin is broken.

USB cable

Cat5e

Microphone

UVC40

Before using the UVC40, please set the audio input and output device to Echo Cancelling

Speakerphone (Yealink UVC40 Audio).

VCR20遥控器 7号电池x2UVC40 7米USB线

束线带x5

此为A级产品。在生活环境中，该产品可能会造成无线电干扰。在这种情况下，可能需要用户对干扰采取

切实可行的措施。

我们推荐使用由Yealink提供或经Yealink认可的配件和线缆，使用未经认可的第三方配件和线缆可能会

导致性能的下降。

使用HDMI线前，请套上磁环用于抗电磁干扰。

MVC400/ZVC400产品组合包中标配的USB线长为2.5米。

UVC40

快速入门指南

支架配件

（用于安装主机）

电源适配器

×4

×2

硅胶垫x2

平放安装

包装清单

安装UVC40

TV TV

放置UVC40

螺丝规格：T4×30

打孔直径： 6mm

打孔深度： 30mm

118mm

步骤1：安装支架

步骤2：墙装

当电视高度高于120cm时，终端安装

在电视下方。

墙装

当电视高度低于120cm时，终端安装

在电视上方。

使用支架将终端安装在墙上。安装高度会影响你的视野，建议的高度为离地面1.1m。

墙装

10cm

H>120cm

H<120cm

调整倾斜角度

15°

安装遥控器和束线带

安装遥控器电池安装束线带

音频线性输入: 连接3.5mm音频接头，将UVC40作为音频输出设备。

视频输出: 连接电脑作为视频输出。

USB: 预留接口。

麦克风：连接麦克风（例如：VCM34）。

电源接口: 连接电源适配器。

重置键：重置设备到出厂设置。

安全锁孔 : 将主机锁在固定位置。

硬件接口介绍

配对键：按配对键，进入配对蓝牙麦状态。

连接UVC40

如果使用过程中发现线缆破皮，请立即更换。

UVC40固件更新中。

UVC40 指示灯介绍如下:

绿灯闪烁

红灯常亮

指示灯介绍

关闭

指示灯状态说明

UVC40没有正确连接到mini-PC上或未处于正常工作状态。

来电中状态。

绿灯常亮 UVC40处于工作中状态。

红灯闪烁 UVC40进入恢复模式，还未固件更新。

UVC40处于静音状态。

红绿灯交替 UVC40和CPW90-BT配对状态。

橙色灯常亮 UVC40启动或等待状态。

橙色灯闪烁

USB线

Cat5e网线

Microphone

UVC40

使用UVC40前，请将音频输入输出设备设置为 Echo Cancelling Speakerphone (Yealink

UVC40 Audio)。

Regulatory Notices

About Yealink

Technical Support

Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product documents, and more. For better service,

we sincerely recommend you to use Yealink Ticketing system (https://ticket.yealink.com) to submit all your technical issues.

Yealink is a global leading provider of enterprise communication and collaboration solutions, offering video conferencing service to

worldwide enterprises. Focusing on research and development, Yealink also insists on innovation and creation. With the outstanding

technical patents of cloud computing, audio, video and image processing technology, Yealink has built up a panoramic collaboration

solution of audio and video conferencing by merging its cloud services with a series of endpoints products. As one of the best

providers in more than 140 countries and regions including the US, the UK and Australia, Yealink ranks No.1 in the global market

share of SIP phones shipments.

Operating Ambient Temperatures

Operating temperature: +32 to 104°F (0 to 40°C)

Relative humidity: 5% to 90%, noncondensing

Storage temperature: -22 to +160°F (-30 to +70°C)

Warranty

Our product warranty is limited only to the unit itself, when used normally

in accordance with the operating instructions and the system environment.

We are not liable for damage or loss resulting from the use of this product,

or for any claim from a third party. We are not liable for problems with

Yealink device arising from the use of this product; we are not liable for

financial damages, lost profits, claims from third parties, etc., arising from

the use of this product.

Explanation of the symbols

DC symbol

is the DC voltage symbol.

WEEE Warning symbol

To avoid the potential effects on the environment and human health

as a result of the presence of hazardous substances in electrical and

electronic equipment, end users of electrical and electronic

equipment should understand the meaning of the crossed-out wheeled bin

symbol. Do not dispose of WEEE as unsorted municipal waste and have to

collect such WEEE separately.

Restriction of Hazardous Substances Directive (RoHS)

This device complies with the requirements of the EU RoHS Directive.

Statements of compliance can be obtained by contacting [email protected].

Safety Instructions

Save these instructions. Read these safety instructions before use!

General Requirements

Before you install and use the device, read the safety instructions

carefully and observe the situation during operation.

During the process of storage, transportation, and operation, please

always keep the device dry and clean, avoid collision and crash.

Please attempt not to dismantle the device by yourself. In case of any

discrepancy, please contact the appointed maintenance center for repair.

Please refer to the relevant laws and statutes while using the device.

Legal rights of others should be respected as well.

Environmental Requirements

Place the device at a well-ventilated place. Do not expose the device

under direct sunlight.

Keep the device dry and free of dusts.

Do not place the device on or near any inflammable or fire-vulnerable

object, such as rubber-made materials.

Keep the device away from any heat source or bare fire, such as a candle

or an electric heater.

Operating Requirements

Do not let a child operate the device without guidance.

Do not let a child play with the device or any accessory in case of

accidental swallowing.

Please use the accessories provided or authorized by the manufacturer

only.

The power supply of the device shall meet the requirements of the input

voltage of the device. Please use the provided surge protection power

socket only.

Before plugging or unplugging any cable, make sure that your hands are

completely dry.

Do not spill liquid of any kind on the product or use the equipment near

water, for example, near a bathtub, washbowl, kitchen sink, wet

basement or near a swimming pool.

During a thunderstorm, stop using the device and disconnect it from the

power supply. Unplug the power plug and the Asymmetric Digital

Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid

lightning strike.

If the device is left unused for a rather long time, disconnect it from the

power supply and unplug the power plug.

When there is smoke emitted from the device, or some abnormal noise

or smell, disconnect the device from the power supply, and unplug the

power plug immediately.

Contact the specified maintenance center for repair.

Do not insert any object into equipment slots that is not part of the

product or auxiliary product.

Before connecting a cable, connect the grounding cable of the device

first. Do not disconnect the grounding cable until you disconnect all other

cables.

Cleaning Requirements

Before cleaning the device, disconnect it from the power supply.

Use a piece of soft, dry and anti-static cloth to clean the device.

Keep the power plug clean and dry.

Troubleshooting

The unit cannot supply power to device other than Yealink device.

There is a bad connection with the plug.

1. Clean the plug with a dry cloth.

2. Connect it to another wall outlet.

The usage environment is out of operating temperature range.

1. Use in the operating temperature range.

The cable between the unit and the Yealink device is connected incorrectly.

1. Connect the cable correctly.

You cannot connect the cable properly.

1. You may have connected a wrong Yealink device.

2. Use the correct power supply.

Some dust, etc., may be in the port.

1. Clean the port.

Contact your dealer or authorized service facility for any further questions.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the

following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may

cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

IC Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is

subject to the following two conditions:

(1) this device may not cause interference; and

(2) this device must accept any interference, including interference that may

cause undesired operation of the device. CAN ICES-3(B)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le

fonctionnement.NMB-3(B)

Radiation Exposure Statement

This equipment complies with FCC and IC radiation exposure limits set forth for

an uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps

qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et

actionné avec une distance minimum de 20 centimètres entre le radiateur et

votre corps.

Contact Information

YEALINK NETWORK TECHNOLOGY CO.,LTD.

309, 3rd Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. C

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX Amsterdam, The Netherlands

YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.

999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA

Made in China

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD.

Web: www.yealink.com

TECHNOLOGY CO.,LTD

430104001406

Yealink Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2 クイックスタートガイド

ブランド: Yealink

モデル: Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2

タイプ: クイックスタートガイド

PDFをダウンロードします

報告

他の言語で

English: Yealink Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2 Quick start guide

その他のドキュメント

TOA ER-1000 WR クイックスタートガイド

Yealink Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2 クイックスタートガイド

Yealink Yealink UVC40 USB Video Conferencing Endpoint (EN, CN) V1.2 クイックスタートガイド

他の言語で

関連論文

その他のドキュメント