D25501
D25601
Final page size: A5 (148mm x 210mm)
Copyright DEWALT
English 3
简体中文 10
16
1
Figure 1A
图 1A
1A
Fig. 2
图 2
2
Fig. 3
图 3
3
1
f
D25601
g
s
r
D25501, D25601
p
x
c
f
p
m
j
w
c
a
e
2
Fig. 4A
图 4A
4A
Fig. 4B
图 4B
4B
Fig. 5
图 5
5
Fig. 6
图 6
6
2
D25501, D25601,
f
m
d
c
3
ENGLISH
WARNING: To reduce the risk of injury, read
the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) WORK AREA SAFETY
a ) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c ) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2) ELECTRICAL SAFETY
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b ) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c ) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
SDS MAX COMBINATION & CHIPPING HAMMERS
D25501, D25601
Congratulations!
You have chosen a DeWALT tool. Years of experience,
thorough product development and innovation make
DeWALT one of the most reliable partners for professional
power tool users.
Technical Data
D25501 D25601
Voltage (B1) V 220-240 220-240
Power input W 1100 1250
Impact energy J 11 1.5–13
Total drilling range in concrete:
solid bits mm 12–40 12–45
core bits mm 40–90 40–100
Optimum drilling range in concrete:
solid bits mm 18–26 25–35
Chisel positions 18 18
Tool holder SDS Max
®
SDS Max
®
Chisel positions kg 6.15 6.8
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING: Indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION: Indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may
result in property damage.
Denotes risk of electric shock.
Denotes risk of fire.
ENGLISH
ENGLISH
4
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
3) PERSONAL SAFETY
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b ) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c ) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
d ) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e ) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g ) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and p roperly used.
Use of dust collection can reduce dust-related
hazards.
4) POWER TOOL USE AND CARE
a ) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
b ) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c ) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d ) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e ) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g ) Use the power tool, accessories and tool bits
etc., in accordance with these instructions
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Additional Safety Instructions for
Rotary Hammers
• Wear ear protectors. Exposure to noise can cause
hearing loss.
• Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live” and
could give the operator an electric shock.
5
ENGLISH
Residual Risks
The following risks are inherent to the use of rotary and
chipping hammers:
– Injuries caused by touching the rotating parts or
hot parts of the tool
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing the
accessory.
– Health hazards caused by breathing dust developed
when working in concrete and/or masonry.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Red service indicator LED. For detailed
description see under Service Indicator LED's.
Yellow service indicator LED. For detailed
description see under Service Indicator LED's.
DATE CODE POSITION (FIG. 1)
The Date Code (w), which also includes the year of
manufacture, is printed into the housing.
Example:
2010 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Rotary hammer
1 Side handle
1 Kitbox (K-models only)
1 Instruction manual
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
Description (fig. 1a, 1b, 2a–c)
WARNING: Never modify the power tool
or any part of it. Damage or personal injury
could result.
a. Trigger switch
c. Side handle
d. Main handle
e. Active vibration control (D25601)
f. Mode selector switch
g. Electronic speed and impact control dial (D25601)
h. Clamp wheel
i. Rear side handle position
j. Side handle clamp
k. Steel ring
l. Bush
m. Tool holder
n. Depth rod release button
o. Depth rod
p. Locking sleeve
q. Pin
x. Collar
INTENDED USE
D25501,D25601
Your rotary hammer has been designed for professional
rotary drilling and chipping applications.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These hammers are professional power tools.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Soft Start Feature
D25601
The soft start feature allows the speed to build up speed
slowly, thus preventing the drill bit from walking off the
intended hole position when starting. The soft start feature
also reduces the immediate torque reaction transmitted to
the gearing and the operator if the hammer is started with
the drill bit in an existing hole.
ENGLISH
6
Electronic Speed and Impact Control
(fig. 1, 3)
D25601
The electronic speed and impact control (g) offers the
following advantages:
– use of smaller accessories without risk of breakage;
– minimised break-out when chiselling or drilling in soft
or brittle materials;
– optimal tool control for precise chiselling.
Torque Limiting Clutch
The torque limiting clutch reduces the maximum torque
reaction transmitted to the operator in case of jamming of a
drill bit. This feature also prevents the gearing and electric
motor from stalling. The torque limiting clutch has been
factory-set and cannot be adjusted.
Service Indicator LEDs (fig. 3)
D25601
The yellow brushwear indicator LED (s) lights up when the
carbon brushes are nearly worn out to indicate that the tool
needs servicing within the next 8 hours of use.
D25601
The red indicator starts to flash if there is a fault with the tool
or the brushes have completely worn out (refer to Brushes
under Maintenance).
Fully Vibration-dampened Main
Handle (fig. 1)
D25601
The dampers in the side handle (c) absorb the vibrations
transmitted to the user. This improves user comfort during
the operation.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the
voltage on the rating plate.
Your DeWALT tool is double insulated in
accordance with IEC 60745; therefore no earth
wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the
DeWALT
service organisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for the
power input of this tool (see technical data). The minimum
conductor size is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An
accidental start-up can cause injury.
WARNING: Tool bits may be hot and gloves
should be worn when changing or removing
them to avoid personal injury.
Assembling and Fitting the Side
Handle (fig. 2A, 2B)
The side handle (c) can be mounted in front or in rear
position on either side of the machine to suit both RH- and
LH-users.
WARNING: Always operate the tool with the
side handle properly assembled.
D25501, D25601
MOUNTING IN FRONT POSITION (FIG. 2A)
1. Snap the steel ring (k) over the collar (x) behind the tool
holder (m). Squeeze both ends together, mount the bush
(l) and insert the pin (q).
2. Place the side handle clamp (j) and screw on the clamp
wheel (h). Do not tighten.
WARNING: Once assembled, the side handle
clamp should never be removed.
3. Screw the side handle (c) into the bush (l) and then into
clamp wheel. Tighten securely.
4. Rotate the side handle mounting assembly to the desired
position. For drilling horizontally with a heavy drill bit,
we recommend to place the side handle at an angle of
approx. 20° for optimum control.
5. Lock the side handle mounting assembly in place by
tightening the clamp wheel (h).
7
ENGLISH
MOUNTING IN REAR POSITION (FIG. 2B)
The rear position is particularly useful when drilling down
into a floor.
1. Unscrew the side handle (c) and remove it from the front
position. Leave the side handle mounting assembly in
front position.
2. Screw the side handle directly into one of the rear side
handle positions (i) on either side of the tool.
Inserting and Removing SDS Max™
Accessories (fig. 1, 4A, 4B)
This machine uses SDS Max
®
bits and chisels (refer to the
inset in figure 4B for a cross-section of an SDS Max
®
bit
shank).
1. Clean the bit shank.
2. Pull back the locking sleeve (p) and insert the bit shank.
3. Turn the bit slightly until the sleeve snaps into position.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be able
to move axially several centimetres when locked in
the tool holder.
5. To remove a bit pull back the tool holder locking sleeve/
collar (p) and pull the bit out of the tool holder.
Selecting the Operating Mode (fig. 1)
Hammerdrilling:
D25501, D25601
for concrete, brick, stone and masonry drilling
operations.
Hammering only:
D25501, D25601
for chiselling and demolition applications. In this
mode the tool can also be used as a lever to free
a jammed drill bit.
1. To select the operating mode, rotate the mode selector
switch (f) until it points to the symbol of the required
mode.
It may be neccessary to twist the tool holder (m)
slightly to allow the mode selector switch (f) to
pass the
position.
2. Check that the mode selector switch (f) is locked in
place.
Indexing the Chisel Position (fig. 5)
D25501, D25601
The chisel can be indexed and locked into 18 different
positions.
1. Rotate the mode selector switch (f) until it points
towards the
position.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch (f) to the
“hammering only” position.
4. Twist the chisel until it locks in position.
Setting the Electronic Speed and
Impact Control Dial (fig. 1, 3)
D25601
Turn the dial (g) to the desired level. Turn the dial upwards
for higher speed and downwards for lower speed. The
required setting is a matter of experience. E.g.:
– when chiselling or drilling in soft, brittle materials or
when minimum break-out is required, set the dial to
a low setting;
– when breaking or drilling in harder materials, set the
dial to a high setting.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect
tool from power source before making
any adjustments or removing/installing
attachments or accessories.
WARNING: Tool bits may be hot and gloves
should be worn when changing or removing
them to avoid personal injury.
WARNING:
• Be aware of the location of pipework and
wiring.
• Apply only a gentle pressure to the tool
(approx. 20 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
• Always hold the tool firmly with both
hands and ensure a secure stance.
Always operate the tool with the side
handle properly assembled.
ENGLISH
8
NOTE: Operating temperature of the D25501 is
-7 to +40˚ C (19˚ to 104˚ F). Using the tool outside of
this temperature range will decrease the life of the tool.
Proper Hand Position (fig. 6)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper hand
position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side handle
(c), with the other hand on the main handle (d).
Switching On and Off (fig. 1)
D25501, D25601
To turn the tool on, depress the trigger switch (a).
To stop the tool, release the trigger switch.
Hammerdrilling
To turn the tool on, press the on/off switch (a).
To stop the tool, release the switch.
Drilling with a Solid Bit (fig. 1)
D25501, D25601
1. Insert the appropriate drill bit.
2. Set the mode selector switch (f) to the hammerdrilling
position.
3. D25601 only: Set the electronic speed and impact
control dial(g).
4. Fit and adjust the side handle (c).
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the tool.
7. Always switch off the tool when work is finished and
before unplugging.
Drilling with a Core Bit (fig. 1)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch (f) to the hammerdrilling
position.
4. D25601 only: Turn the electronic speed and impact
control dial (g) to a medium or high speed setting.
5. Fit and adjust the side handle (c).
6. Place the centerdrill on the spot and switch on the tool.
Drill until the core penetrates into the concrete approx.
1 cm.
7. Stop the tool and remove the centerdrill. Place the core
bit back into the hole and continue drilling.
8. When drilling through a structure thicker than the depth
of the core bit, break away the round cylinder of concrete
or core inside the bit at regular intervals.
To avoid unwanted breaking away of concrete around
the hole, first drill a hole the diameter of the centerdrill
completely through the structure. Then drill the cored hole
halfway from each side.
9. Always turn the tool off when work is finished and before
unplugging.
Chipping and Chiselling (fig. 1)
D25501, D25601
1. Insert the appropriate chisel and rotate it by hand to lock
it into one of 18 positions.
2. Set the mode selector switch (f) to the hammering only
position.
3. D25601 only: Set the electronic speed and impact
control dial(g).
4. Fit and adjust the side handle (c).
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished and before
unplugging.
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An
accidental start-up can cause injury.
This machine is not user-serviceable. Take the tool to an
authorised
DeWALT repair agent after approximately
150 hours of use. If problems occur before this time contact
an authorised DeWALT repair agent.
9
ENGLISH
Protecting the Environment
Separate collection. This product must
not be disposed of with normal household
waste.
Should you find one day that your DeWALT product needs
replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
DeWALT provides a facility for the collection and recycling of
DeWALT products once they have reached the end of their
working life. To take advantage of this service please return
your product to any authorised repair agent who will collect
them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local
DeWALT office at the address
indicated in this manual. Alternatively, a list of authorised
DeWALT repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
Brushes (fig. 3)
The carbon brushes are not user-serviceable. Take the tool
to an authorized DeWALT repair agent.
The yellow brushwear indicator LED (r) lights up when the
carbon brushes are nearly worn out. After a further 8 hours
of use or after the brushes have completely worn out the
motor will automatically be shut offf.
Tool maintenance needs to be carried out as soon as the
service indicator (s) lights up.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust
mask when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the
materials used in these parts. Use a cloth
dampened only with water and mild soap.
Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than
those offered by DeWALT, have not been tested
with this product, use of such accessories with
this tool could be hazardous. To reduce the
risk of injury, only
DeWALT, recommended
accessories should be used with this product.
Various types of SDS Max
®
drill bits and chisels are available
as an option.
Consult your dealer for further information on the appropriate
accessories.
简体中文
10
警告：为降低伤害风险，请阅读使用
手册。
电动工具通用安全警告
警告！阅读随电动工具提供的所有安全
警 告 、说 明 、图 示 和 规 定 。不遵照以下
所列说明会导致电击、着火和／或严重
伤害。
保存所有警告和说明书以备查阅。
警告中的术语“电动工具”指市电驱动（有线）电动
工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1 ) 保持工作场地清洁和明亮。杂乱和黑暗的场
地会引发事故。
2 ) 不要在易爆环境，如有易燃液体、气体或粉尘
的环境下操作电动工具。电动工具产生的火
花会点燃粉尘或气体。
3 ) 操作电动工具时，远离儿童和旁观者。注意力
不集中会使操作者失去对工具的控制。
b) 电气安全
1 ) 电动工具插头必须与插座相配。绝不能以任
何方式改装插头。需接地的电动工具不能使
用任何转换插头。未经改装的插头和相配的
插座将降低电击风险。
2 ) 避免人体接触接地表面，如管道、散热片和
冰箱。如果你身体接地会增加电击风险。
3 ) 不得将电动工具暴露在雨中或潮湿环境中。
水进入电动工具将增加电击风险。
4 ) 不得滥用电线。绝不能用软线搬运、拉动电
动工具或拔出其插头。使软线远离热源、油、
锐边或运动部件。受损或缠绕的软线会增加
电击风险。
5 ) 当在户外使用电动工具时，使用适合户外使
用的延长线。适合户外使用的电线将降低电
击风险。
6 ) 如果无法避免在潮湿环境下操作电动工具，
应 使 用 带 有 剩 余 电 流 装 置（ RCD）保 护 的
电源。RCD 的使用可降低电击风险。
SDS MAX 多功能五坑电锤
D25501, D25601
恭 喜！
您已选择了得伟工具。凭借多年的产品开发和创新
经验，得伟已经成为专业电动工具用户最可靠的合
作伙伴之一。
技术参数
D25501 D25601
电压
伏特
220-240 220-240
输入功率 瓦
1100 1250
冲击能量 焦
11 1.5–13
混凝土中的最大钻深：
实心钻头 毫米
12–40 12–45
空心钻头 毫米
40–90 40–100
混凝土中的最佳钻深：
实心钻头 毫米
18–26 25–35
凿子位置
18 18
工具夹持器
SDS Max
®
SDS Max
®
凿子位置 千克
6.15 6.8
定 义 ：安 全 指 南
下列定义描述了各标志术语的严重程度。请仔细阅
读本手册，并注意这些标志。
危险：表示存在紧急危险情况，如果不加
以避免，将导致死亡或严重伤害。
警告：表示存在潜在的危险情况，如果不
加以避免，可能导致死亡或严重伤害。
警示：表示存在潜在危险情况，如果不加
以避免，可能导致轻度或中度伤害。
注意：表示存在不涉及人身伤害的情况，
如果不加以避免，可能导致财产损失。
表示存在触电风险。
表示存在火灾风险。
11
简体中文
c) 人身安全
1 ) 保持警觉，当操作电动工具时关注所从事
的操作并保持清醒。当你感到疲倦，或在有
药物、酒精或治疗反应时，不要操作电动
工具。在操作电动工具时瞬间的疏忽会
导致严重人身伤害。
2 ) 使用个人防护装置。始终佩戴护目镜。防护
装置，诸如适当条件下使用防尘面具、防滑
安全鞋、安全帽、听力防护等装置能减少人
身伤害。
3 ) 防止意外起动。在连接电源和/或电池盒、
拿起或搬运工具前确保开关处于关断位置。
手指放在开关上搬运工具或开关处于接通时
通电会导致危险。
4 ) 在电动工具接通之前，拿掉所有调节钥匙或
扳手。遗留在电动工具旋转零件上的扳手或
钥匙会导致人身伤害。
5 ) 手不要过分伸展。时刻注意立足点和身体
平衡。这样能在意外情况下能更好地控制
住电动工具。
6 ) 着装适当。不要穿宽松衣服或佩戴饰品。
让你的头发和衣服远离运动部件。宽松
衣服、佩饰或长发可能会卷入运动部件。
7 ) 如果提供了与排屑、集尘设备连接用的装置，
要确保其连接完好且使用得当。使用集尘装
置可降低尘屑引起的危险。
8 ) 不要因为频繁使用工具而产生的熟悉感而掉
以 轻 心 ，忽 视 工 具 的 安 全 准 则 。某个粗心的动
作可能在瞬间导致严重的伤害。
d) 电动工具使用和注意事项
1 ) 不要勉强使用电动工具，根据用途使用合适
的电动工具。选用合适的按照额定值设计的
电动工具会使你工作更有效、更安全。
2 ) 如果开关不能接通或关断电源，则不能使用
该电动工具。不能通过开关来控制的电动工
具是危险的且必须进行修理。
3 ) 在进行任何调节、更换附件或贮存电动工具
之前，必须从电源上拔掉插头和／或卸下电
池包
(如可拆卸)。这种防护性的安全措施降
低了电动工具意外起动的风险。
4 ) 将闲置不用的电动工具贮存在儿童所及范围
之外，并且不允许不熟悉电动工具和不了解
这些说明的人操作电动工具。电动工具在未
经培训的使用者手中是危险的。
5 ) 维护电动工具及其附件。检查运动部件是否
调整到位或卡住，检查零件破损情况和影响
电动工具运行的其他状况。如有损坏，应在使
用前修理好电动工具。许多事故是由维护不
良的电动工具引发的。
6 ) 保持切削刀具锋利和清洁。维护良好地有锋
利切削刃的刀具不易卡住而且容易控制。
7 ) 按照使用说明书，并考虑作业条件和要进
行的作业来选择电动工具、附件和工具的
刀头等。将电动工具用于那些与其用途不符
的操作可能会导致危险情况。
8 ) 保持手柄和握持表面干燥、清洁，不得沾有
油脂。在意外的情况下，湿滑的手柄不能保证
握持的安全和对工具的控制。
e) 维修
1 ) 由专业维修人员使用相同的备件维修电动
工具。这将保证所维修的电动工具的安全。
锤类工具的安全警告：
• 戴好耳罩。暴露在噪声中会引起听力损伤。
• 使用随工具提供的辅助手柄。操作失手会引起
人身伤害。
• 在切削附件可能触及暗线或其自身软线之处
进行操作时，要通过绝缘握持面来握持工具。
切削附件碰到带电导线会使工具外露的金属零件
带电从而使操作者受到电击。
剩余风险
使用电锤和电镐时具有下列固有危险：
– 碰触工具的旋转部件或发热部件会导致人身
伤害
尽管遵守了相关的安全法规并采用了安全装备，
某些其他风险仍然是无法避免的。这些风险包括：
– 听力损伤。
– 更换附件时夹到手指的风险。
– 在混凝土和/或砖石环境中工作时，吸入粉尘导
致的健康危害。
工具上的标记
工具上印有下列图形：
使用前阅读使用手册。
红色维修 LED 指 示 灯 。要 了 解 详 细 说 明 ，
请 参 阅“ 维修 LED 指示灯”的 相 关 内 容 。
黄色维修 LED 指 示 灯 。要 了 解 详 细 说 明 ，
请 参 阅“ 维修 LED 指示灯”的 相 关 内 容 。
简体中文
12
日期码位置（图 1）
包含制造年份的日期码 (w) 打印在工具机壳内。
示例：
制造年份
2010 XX XX
包装内的物品
包装内的物品包括：
1 把电锤
1 只侧手柄
1 个 工 具 箱（ 仅 适 用 于 K 型号）
1 本使用手册
• 检查工具、部件或配件是否在运输过程中
损坏。
• 操作前，请抽空仔细阅读并掌握本手册。
说 明（ 图 1a, 1b, 2a–c）
警告：切勿改装电动工具或其任何部件。
否则可能会导致损坏或人身伤害。
a. 触发开关
c. 侧手柄
d. 主手柄
e. 有源振动控制 (D25601)
f. 模式选择器开关
g. 电子变速器和冲击控制旋钮 (D25601)
h. 紧固轮
i. 后侧手柄位置
j. 侧手柄夹钳
k. 钢环
l. 衬套
m. 工具夹持器
n. 深度调节杆释放按钮
o. 深度调节杆
p. 锁定套管
q. 销
x. 轴环
设计用途
D25501,D25601
您的电锤设计用于专业旋转钻孔和切削应用。
请勿在潮湿环境中或在有易燃液体或气体的环境中
使用。
这些电锤是专业型电动工具。
请勿让儿童接触工具。缺乏经验的操作员需要在监
督下使用本工具。
软启动功能
D25601
工具的软启动功能可以缓慢加速，以防钻头在工具
启动时偏离钻孔位置。如果电锤启动时钻头位于已有
的 孔 中 ，则 软 启 动 功 能 还 会 降 低 直 接 传 递 到 排 档 和
操作员的扭转效应。
电子变速器和冲击控制（图 1, 3）
D25601
电子变速器和冲击控制 (g) 具有以下优点：
– 使用较小型附件，无破损风险；
– 在软质或易脆材料上凿切或钻孔时可最大程度
降低破损；
– 是精确凿切的最 佳 工具控制装置。
扭矩限制离合器
扭矩限制离合器可减少钻头卡住时传递到操作员的最
大扭矩效应。此功能还可防止排挡和电机失速。扭矩
限制离合器采用出厂设置，无法调节。
维修 LED 指示灯
（
图 3）
D25601
黄色电刷磨损 LED 指示灯 (s) 在碳刷接近损坏时会
亮 起 ，表 明 工 具 需 要 在 之 后 8 个小时的使用中进行
维修。
D25601
如果工具出现故障，或者电刷完全磨损，则红色
指示灯会开始闪烁
(请 参 阅“ 维护”中 的“ 电刷”
部分
)。
减 震 主 手 柄（ 图 1）
D25601
侧手柄 (c) 上的减震层可吸收传递至操作员的
震动，提高操作员在操作过程中的舒适感。
电气安全
电机只适用一种工作电压。请务必检查电源电压是
否与铭牌上的电压一致。
您的得伟工具依据 IEC 60745 标准设置双重
绝 缘 ；因 此 无 须 接 地 线 。
如果电源线损坏，必须采用得伟维修机构提供的专
用电线进行更换。
13
简体中文
使用延长线
除非绝对必要，否则请勿使用延长线。使用适合
本工具输入功率的合格延长电缆（请参见
“技术
参数
”)。最小的导线尺寸为 1 平方毫米; 最大长度
为 30 米。
使用电缆卷筒时，请务必拉出所有的电缆。
组装与调整
警 告 ：为 降 低 人 身 伤 害 的 风 险 ，在 拆 、装
配件或调整、修理工具之前，请关闭工具
并拔下工具插头。请确保触发开关处于
OFF（关闭）位置。意外启动可能会导致
人身伤害。
警告：工具钻头可能发热，因此更换或取
下钻头时必须佩戴手套以防受伤。
组装和安装侧手柄（图 2A、2B）
侧手柄 (c) 可 安 装 在 机 器 任 一 侧 的 前 端 或 后 端 ，以 适
合右手和左手操作员。
警告：务必在正确组装侧手柄后才操作
工具。
D25501，D25601
安装在前端位置（图 2A）
1. 将钢环 (k) 夹在工具夹持器 (m) 后面的轴环
(x) 中 。挤 压 两 端 ，安 装 衬 套 (l) 并插入销 (q)。
2. 将侧手柄夹钳 (j) 拧到紧固轮 (h) 上 。请 勿 拧 紧 。
警告：组装好后，切勿取下侧手柄夹钳。
3. 将侧手柄 (c) 拧进衬套 (l) ，再 拧 进 紧 固 轮 。然 后
拧紧。
4. 将侧手柄安装组件旋转至所需位置。在使用重型
钻头进行水平钻孔时，我们建议将侧手柄调整到
约 20° 的角度以便获得最好的控制。
5. 通过转紧紧固轮 (h) 将侧手柄安装组件锁定
到位。
安装在后端位置（图 2B）
在地板上钻孔时，后端位置尤其实用。
1. 拧开侧手柄 (c) 并 将 其 从 前 端 位 置 取 下 。将 侧 手
柄安装组件置于前端位置。
2. 将侧手柄直接拧入工具两侧的一个后侧手柄位
置 (i)。
插入和取出 SDS Max™
附 件（ 图 1、4A、4B）
本机器使用 SDS Max
®
钻头和凿子 (请参阅插页中的
图 4B 获取 SDS Max
®
钻头杆的横截面图)。
1. 清洁钻头杆。
2. 向后拉锁定套管 (p) 然后插入钻头杆。
3. 稍微转动钻头直到套 管卡入 到位。
4. 拉动钻头以检查它是否正确锁定。锤击功能需要
钻头在锁定到工具夹持器中时可以轴向移动数
厘米。
5. 要取下钻头，请向后拉工具夹持器锁定套管/轴环
(p)，然后从工具夹持器中拉出钻头。
选择操作模式（图 1)
锤钻：
D25501，D25601
用于在混凝土和砖石上钻孔。
仅锤击：
D25501，D25601
用 于 凿 切 和 破 碎 作 业 。在 此 模 式 下 ，
工具还可用作杠杆，便于取出卡住的
钻头。
1. 要选择操作模式，请旋转模式选择器开关 (f) 直
到其指向所需的模式符号。
可能需要轻微扭转工具夹持器 (m) 才能让模式
选择器开关 (f) 经过
位置。
2. 确保模式选择器开关 (f) 锁定到位。
标 记 凿 子 位 置（ 图 5）
D25501，D25601
可标记凿子并将它锁定在 18 个不同的位 置中。
1. 旋转模式选择器开关 (f) 直到它指向
位置。
2. 将凿子旋转至所需位置。
3. 将模式选择器开关 (f) 旋 转 到“ 锤 击 ”位 置 。
4. 扭转凿子，直到其锁定到位。
设置电子变速器和冲击控制
旋 钮（ 图 1，3）
D25601
将旋钮 (g) 转至所需等级。将旋钮向上旋转选择较高
转速，向下旋转选择较低转速。依据经验设置所需
操 作 。例 如 ：
简体中文
14
– 在软质、易脆材料上凿切或钻孔，或在需要最
大限度降低破损时，将旋钮调整为低设置；
– 在硬质材料上钻孔或进行破碎时，将旋钮调整
为高设置。
操作
使用说明
警告：请务必遵守安全说明和适用
法规。
警 告 ：为 降 低 严 重 的 人 身 伤 害 风 险 ，
在进行任何调整或取出/安装附件或配
件之前，请关闭工具电源和断开工具电
源连接。
警告：工具钻头可能发热，因此更换或取
下钻头时必须佩戴手套以防受伤。
警告：
• 注意水管和电线的布线位 置。
• 轻轻地对工具施加压力 (约 20 千克)。
过度用力不但不会加快钻孔的速度，
而且会降低工具性能并可能缩短工具
使用寿命。
• 务必用双手紧握工具并确保站稳。
务必在正确组装侧手柄后才操作
工具。
注：
D25501 的工作温度为 -7 至 40˚C（19˚ 至 104˚F）在 此
温度范围外使用工具会降低工具的使用寿命。
正确的手持方式（图 6）
警告：为降低严重的人身伤害风险，请务
必使用正确的手持方式，如图所示。
警告：为降低严重的人身伤害风险，请
务必紧握工具以防止出现突然的反作
用力。
正确的手持方式要求一只手握住侧手柄 (c) ，另 一 只
手则握住主手柄 (d)。
开 启 和 关 闭（ 图 1)
D25501，D25601
要启动工具，请按下触发开关 (a)。
要停止工具，请松开触发开关。
锤钻
要启动工具，请按下开关 (a)。
要停止工具，请松开开关。
使用实心钻头钻孔（图 1)
D25501，D25601
1. 插入相应的钻头。
2. 将模式选择器开关 (f) 旋转到锤钻位置。
3. 仅适用于 D25601：设置电子变速器和冲击控制
旋钮 (g)。
4. 安装和调整侧手柄 (c)。
5. 在要钻孔的位置做标记。
6. 将钻头对准标记并开启工具。
7. 作业结束后，务必先关闭工具开关，然后再拔下
工具插头。
使用空心钻头钻孔（图 1)
1. 插入相应的空心钻头。
2. 将中心钻组装到空心钻头中。
3. 将模式选择器开关 (f) 旋转到锤钻位置。
4. 仅适用于 D25601：将电子变速器和冲击控制
旋钮 (g) 旋转到中高级转速设置。
5. 安装和调整侧手柄 (c)。
6. 将中心钻对准钻孔位置并启动工具。进行钻孔
操作，直到钻心穿透混凝土大约 1 厘米。
7. 停止工具然后取下中心钻。将空心钻头放回孔
中继续钻孔。
8. 当要钻孔的材料厚度大于空心钻头的深度时，
可定期清理钻头内的圆柱体混凝土或材料。
要避免意外碎裂孔周围的混凝土，可先在材料
上钻一个中心钻直径大小的孔，孔要完全穿透
材料。然后使用空心钻头从两边往中心钻孔。
9. 作业结束后，务必先关闭工具，然后再拔下工具
插头。
切 削 和 凿 切（ 图 1)
D25501，D25601
1. 插入相应的凿子然后手动旋转直到凿子锁定到
18 个 位 置的其中一 个。
2. 将模式选择器开关 (f) 旋转到锤击位置。
3. 仅适用于 D25601：设置电子变速器和冲击控制
旋钮 (g)。
4. 安装和调整侧手柄 (c)。
15
简体中文
5. 启动工具然后开始作业。
6. 作业结束后，务必先关闭工具，然后再拔下工具
插头。
维护
您的得伟电动工具设计精良，可以长期使用，仅需极
少维护。要连续获得令人满意的工作效果，需要进行
合适的工具维护和定期清洁。
警 告 ：为 降 低 人 身 伤 害 的 风 险 ，在 拆 、装
配件或调整、修理工具之前，请关闭工具
并拔下工具插头。请确保触发开关处于
OFF（关闭）位置。意外启动可能会导致
人身伤害。
本工具不允许用户自行维修。在使用大约 150 小
时后，请将工具交由得伟授权维修代理进行检修。
如果在此之前工具发生任何问题，请联系得伟授权
维修代理。
电 刷（ 图 3）
碳刷不可由用户自行维修。请将工具送交得伟授权
维修代理。
黄色电刷磨损 LED (r) 指示灯会在碳刷接近损坏时
亮 起 。之 后 再 使 用 8 小时或在电刷完全磨损后，
电机会自动关闭。
维修指示灯 (s) 亮 起 后 ，必 须 尽 快 对 工 具 进 行 维 护 。
润滑
本电动工具无需另行润滑。
清洁
警告：一旦看到通风口及其周围积聚了
尘屑，请用干燥的空气将灰尘和尘屑从
主机外壳内吹出。执行此过程时，需戴上
经认可的护目装备和防尘面具。
警告：切勿使用溶剂或其他刺激性化
学制品来清洁工具的非金属部件。这些
化学物质可能会削弱这些部位使用的
材料。请用布蘸温和的肥皂水擦拭。切勿
让任何液体渗入工具，切勿让工具的任
何部件浸在液体中。
可选配件
警告：除 了 得 伟 提 供 的 附 件 之 外 ，其 他
附件都未经此产品兼容性测试，若将此
类附件与本工具一起使用将存在安全
隐患。为降低人身伤害风险，本产品只
可使用得伟推荐的附件。
有各种不同类型的 SDS Max
®
钻头和凿子可供选购。
请向您的经销商咨询更多关于合适配件的信息。
保护环境
分类回收。本产品不得与普通家庭垃圾
一起处理。
如果您发现您的得伟产品需要更换或您已经不再
需要使用这些产品，请不要将它们与家庭垃圾一起
处理。请将它们单独分类回收。
分类回收使用过的产品和包装能够让材
料得以再循环和再利用。再生材料的再
利 用 有 助 于 防 止 环 境 污 染 ，并 降 低 对 原
材料的需求。
当地法规可能要求由市政废物处理点或向您出售新
产品的零售商提供将家庭废物与电气产品分开收集
的服务。
得伟提供设施收集和再循环利用以处理寿命到期的
得伟产品。若要享受这项服务，请将产品送回任一
授权维修代理处，他们将代表我们回收您的产品。
请根据本手册所提供的地址与当地得伟办事处联
系，查询离您最近的授权维修代理的位置。您也可
以通过网站获取得伟授权维修代理名单以及我们售
后服务与联络人的完整详情，网址为：
www.2helpU.com.
16
:
!
1)
2)
()
DeWALT
DeWALT
D25501 D25601
220-240 220-240
1100 1250
11 1.5–13
12–45
40–90 40–100
18–26 25–35
18 18
®
®
6.15 6.8
:
:
:
17
3)
4)
18
–
–
–
–
:
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
