D25721
D25722
D25723
D25761
D25762
D25763
D25871
B
English (original instructions) 5
简体中文 14
繁體中文 23
한국어 32
ภาษาไทย
41
1
Figure 1A
D25721/D25722/D25723
f
e
a
g
b
e
c
h
d
i
o
l
t
f
D25761/D25762/D25763
f
e
a
g
b
e
c
d
t
w
w
i
o
l
h
2
Figure 2A
j
i
m
h
c
k
o
l
Figure 1B
a
g
f
c
e
p
d
l
o
w
e
D25871
n
3
c
p
j
Figure 3
Figure 2B
Service
Lock-On
Brush Service
DEW
ALT, D-65510
IDSTEIN, GERMANY
www.2helpU.com
www.DEWALT.eu
r
g
s
u
v
t
D25722/D25762
r
g
s
D25871
r
g
s
u
v
t
D25723/D25763
r
g
s
D25721/D25761
y
4
Figure 6
d
c
Figure 5
Figure 4B
Figure 4A
D25871
f
D25721/D25722/
D25723/ D25761/
D25762/D25763
c
d
English
5
SDS MAX
®
COMBINATION & CHIPPING HAMMERS
D25721, D25722, D25723, D25761,D25762, D25763, D25871
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make
DeWALT one of the most reliable partners for professional power tool users.
Technical Data
D25721 D25722 D25723 D25761 D25762 D25763 D25871
Voltage V 220-240 220-240 220-240 220-240 220-240 220-240 220-240
Type 1 1 1 1 1 1 1
Power input W 1350 1400 1400 1500 1500 1500 1400
Impact energy J 1.5–15 1.5–15 1.5–15 3–18 3–18 3–18 1.5–15
Total drilling range in concrete:
solid bits mm 12–48 12–48 12–48 18-52 18-52 18-52 –
core bits mm 40–115 40–125 40–125 40–150 40–150 40–150 –
Optimum drilling range in concrete:
solid bits mm 25–40 25–45 25–45 28–48 28–48 28-48 –
Chisel positions 24 24 24 24 24 24 24
Tool holder SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
Weight kg 8.7 9.1 9.1 9.9 9.9 9.9 8.0
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warningS and inStructionS
for future reference
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
English
6
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
English
7
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions for
Rotary Hammers
• Wear ear protectors. Exposure to noise can
cause hearing loss.
• Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
• Hold power tool by insulated gripping
surfaces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
could give the operator an electric shock.
Residual Risks
The following risks are inherent to the use of rotary
and chipping hammers:
– Injuries caused by touching the rotating parts or
hot parts of the tool
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing.
– Risk of squeezing fingers when changing the
accessory.
– Health hazards caused by breathing dust
developed when working in concrete and/or
masonry.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual
before use.
Wear ear protection.
Wear eye protection.
Clutch Setting 40Nm is designed for
most drilling applications.
Clutch Setting 80Nm is designed for
higher torque applications.
Red service indicator LED. For detailed
description see under Service Indicator
LED's.
Yellow service indicator LED. For detailed
description see under Service Indicator
LED's.
DATE CODE POSITION (FIG. 1)
The Date Code (w), which also includes the year of
manufacture, is printed into the housing.
Example:
2013 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Rotary hammer
(D25721, D25722, D25723, D25761,D25762,
D25763)
or
1 Chipping Hammer (D25871)
1 Side handle
1 Kitbox (K-models only)
1 Pointed chisel (only D25871)
1 Instruction manual
• Checkfordamagetothetool,partsor
accessories which may have occurred during
transport.
• Takethetimetothoroughlyreadand
English
8
understand this manual prior to operation.
Description (fig. 1A, 1B, 2A, 2B)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Trigger switch (D25721, D25722, D25723,
D25761,D25762, D25763)
On/off rocker switch (D25871)
b. Lock-on slider (D25721, D25722, D25723,
D25761,D25762, D25763)
c. Side handle
d. Main handle
e. Active vibration control
f. Mode selector switch
g. Electronic speed and impact control dial
h. Clamp wheel
i. Side handle clamp
j. Steel ring
k. Bush
l. Tool holder
m. Pin
n. Collar
o. Locking sleeve
p. Side handle knob
INTENDED USE
D25721, D25722, D25723, D25761,D25762, D25763
Your rotary hammer has been designed for
professional rotary drilling and chipping applications.
D25871
Your chipping hammer has been designed for
professional chipping, chiselling and demolition
applications.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These hammers are professional power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
• Thisproductisnotintendedforusebypersons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Soft Start Feature
D25722, D25723, D25761,D25762, D25763
The soft start feature allows the tool to accelerate
slowly, thus preventing the drill bit from walking off
the intended hole position when starting.
The soft start feature also reduces the immediate
torque reaction transmitted to the gearing and the
operator if the hammer is started with the drill bit in
an existing hole.
Electronic Speed and Impact Control
(fig. 1, 3)
The electronic speed and impact control (g) offers
the following advantages:
– use of smaller accessories without risk of
breakage;
– minimised break-out when chiselling or drilling in
soft or brittle materials;
– optimal tool control for precise chiselling.
Torque Limiting Clutch
WARNING: The user must always
maintain a firm grip on the tool when in
operation.
The torque limiting clutch reduces the maximum
torque reaction transmitted to the operator in case
of jamming of a drill bit. This feature also prevents
the gearing and electric motor from stalling.
NOTICE: Always turn the tool off before
changing torque control settings or
damage to tool may result.
COMPLETE TORQUE CONTROL (CTC) (FIG. 3)
D25722/D25761/D25762
Complete Torque Control (CTC) offers the user a
two-stage mechanical clutch with adjustable torque
options. Adjusting the torque provides increased
control for various applications.
The low setting (40Nm) allows the tool to operate at
a reduced torque level increasing control for many
solid drilling applications. The high setting (80Nm) is
available for more demanding applications such as
core drilling and the use of large diameter solid bits.
Refer to Setting the Two Stage Mechanical
Clutch for more information.
English
9
ULTIMATE TORQUE CONTROL (UTC)
D25723/D25763
In addition to the two-stage mechanical clutch,
Ultimate Torque Control (UTC) offers increased
user comfort and safety through an on-board,
anti-rotation technology capable of detecting if
the user loses control of the hammer. When a jam
is detected, the torque and speed are reduced
instantly. This feature prevents self rotation of the tool
reducing the occurrence of wrist injuries.
Service Indicator LEDs (fig. 3)
The yellow brushwear indicator LED (s) lights up
when the carbon brushes are nearly worn out to
indicate that the tool needs servicing within the next
8 hours of use.
D25721, D25722, D25723, D25761,DD25762, D25763
The red service indicator LED (r) lights up if the
lock-on button (b) is used in any mode except the
chipping mode. On models fitted with Ultimate
Torque Control (UTC), the red LED indicator (r) lights
up if the anti-rotational device is activated. The red
indicator starts to flash if there is a fault with the tool
or the brushes have completely worn out (refer to
Brushes under Maintenance).
D25871
The red service indicator LED (r) lights up if there is
a fault with the tool or the brushes have completely
worn out (refer to Brushes under Maintenance).
Fully Vibration-dampened Main
Handle (fig. 1)
The dampers in the main handle (d) absorb the
vibrations transmitted to the user. This improves user
comfort during the operation.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DeWALT tool is double insulated in
accordance with IEC 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DeWALT service organisation.
Using an Extension Cable
If an extension cable is required, use an approved 3–
core extension cable suitable for the power input of
this tool (see technical data).The minimum conductor
size is 1.5 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: Tool bits may be hot and
gloves should be worn when changing
or removing them to avoid personal
injury.
Assembling and Fitting the Side
Handle (fig. 2A, 2B)
The side handle (c) can be mounted on either side
of the machine to suit both right- and left-handed
users.
WARNING: Always operate the
tool with the side handle properly
assembled.
D25721, D25722, D25723, D25761,D25762, D25763
MOUNTING IN FRONT POSITION (FIG. 2A)
1. Snap the steel ring (j) over the collar (n) behind
the tool holder (l). Squeeze both ends together,
mount the bush (k) and insert the pin (m).
2. Place the side handle clamp (i) and screw on
the clamp wheel (h). Do not tighten.
WARNING: Once assembled, the side
handle clamp should never be removed.
3. Screw the side handle (c) into the bush (k) and
then into clamp wheel. Tighten securely.
4. Rotate the side handle mounting assembly to
the desired position. For drilling horizontally with
a heavy drill bit, we recommend to place the
side handle at an angle of approximately 20° for
optimum control.
5. Lock the side handle mounting assembly in
place by tightening the clamp wheel (h).
English
10
D25871 (FIG. 2B)
1. Unscrew the side handle knob (p).
2. Slide the side handle assembly onto the
machine locating the steel ring (j) in the
mounting area (y). The correct position of the
side handle is between head and middle of the
tube.
3. Adjust the side handle (c) to the desired angle.
4. Slide and rotate the side handle to the desired
position.
5. Lock the side handle in place by tightening the
knob (p).
Inserting and Removing SDS Max
®
Accessories (fig. 1, 4A, 4B)
This machine uses SDS Max
®
bits and chisels (refer
to the inset in figure 4B for a cross-section of an
SDS Max
®
bit shank).
1. Clean the bit shank.
2. Pull back the locking sleeve (o) and insert the bit
shank.
3. Turn the bit slightly until the sleeve snaps into
position.
4. Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
5. To remove a bit pull back the tool holder locking
sleeve/collar (o) and pull the bit out of the tool
holder (l).
Selecting the Operating Mode
(fig. 1)
Hammerdrilling:
D25721, D25722, D25723, D25761,D25762,
D25763
for concrete, brick, stone and masonry
drilling operations.
Hammering only:
for chiselling and demolition applications.
In this mode the tool can also be used as
a lever to free a jammed drill bit.
1. To select the operating mode, rotate the mode
selector switch (f) until it points to the symbol of
the required mode.
It may be neccessary to twist the tool holder (l)
slightly to allow the mode selector switch (f) to
pass the position.
2. Check that the mode selector switch (f) is
locked in place.
Indexing the Chisel Position
(fig. 5)
The chisel can be indexed and locked into 24
different positions.
1. Rotate the mode selector switch (f) until it points
towards the position.
2. Rotate the chisel in the desired position.
3. Set the mode selector switch (f) to the
“hammering only” position.
4. Twist the chisel until it locks in position.
Setting the Electronic Speed and
Impact Control Dial (fig. 1, 3)
Turn the dial (g) to the desired level. Turn the dial
upwards for higher speed and downwards for
lower speed. The required setting is a matter of
experience, e.g.
– when chiselling or drilling in soft, brittle materials
or when minimum break-out is required, set the
dial to a low setting;
– when breaking or drilling in harder materials, set
the dial to a high setting.
Setting the Two Stage Mechanical
Clutch (fig. 3)
D25722, D25723, D25761,D25762, D25763
NOTICE: Always turn the tool off before
changing torque control settings or
damage to the tool may result.
Move the torque control lever (t) to setting 40Nm or
80Nm as needed for application.
• Clutch Setting 40Nm (u) is designed for most
drilling applications and is designed to easily
clutch out when the drill bit encounters re-bar or
other foreign substances.
• ClutchSetting80Nm(v)isdesignedforhigher
torque applications such as core-bits and deep
hole drilling and is designed to clutch out at a
higher torque threshold.
NOTE: If it is not possible to select position 80Nm
run the unit under load and try again.
Each time the tool is plugged in, it will automatically
default to clutch setting 1 into clutch setting 40Nm
(u), the most sensitive setting.
English
11
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
WARNING: Tool bits may be hot and
gloves should be worn when changing
or removing them to avoid personal
injury.
WARNING:
•Be aware of the location of pipework
and wiring.
•Apply only a gentle pressure to the
tool (approximately 20 kg). Excessive
force does not speed up drilling but
decreases tool performance and may
shorten tool life.
•Always hold the tool firmly with both
hands and ensure a secure stance.
Always operate the tool with the side
handle properly assembled.
NOTE: Operating temperature is -7˚ to +40˚C (19˚
to 104˚ F). Using the tool outside of this temperature
range will decrease the life of the tool.
Proper Hand Position (fig. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the
side handle (c), with the other hand on the main
handle (d).
Switching On and Off (fig. 1)
D25721, D25722, D25723, D25761,D25762, D25763
To turn the tool on, depress the trigger switch (a).
To stop the tool, release the trigger switch.
D25721, D25722, D25723, D25761,D25762, D25763
The lock-on slider (b) allows the trigger switch (a) to
be locked on in chiselling mode only. If the lock-on
button is activated in drilling mode, as a feature the
tool will switch off automatically.
To turn the tool on, press the trigger switch(a).
To stop the tool, release the switch.
For continuous operation, press and hold down the
switch (a), slide the lock-on button (b) upwards and
release the switch.
To stop the tool in continuous operation, press the
switch briefly and release it. Always switch off the
tool when work is finished and before unplugging.
D25871
To turn the tool on, press the on/off rocker switch (a)
at the lower part of the trigger.
To stop the tool, press the on/ off rocker switch at
the upper part of the trigger.
Hammerdrilling
To turn the tool on, press the on/off switch(a).
To stop the tool, release the switch.
Drilling with a Solid Bit (fig. 1)
D25721, D25722, D25723, D25761,D25762, D25763
1. Insert the appropriate drill bit.
2. Set the mode selector switch (f) to the
hammerdrilling position.
3. Set the electronic speed and impact control
dial(g).
4. Fit and adjust the side handle (c).
5. Mark the spot where the hole is to be drilled.
6. Place the drill bit on the spot and switch on the
tool.
7. Always switch off the tool when work is finished
and before unplugging.
Drilling with a Core Bit (fig. 1)
1. Insert the appropriate core bit.
2. Assemble the centerdrill into the core bit.
3. Set the mode selector switch (f) to the
hammerdrilling position.
4. Turn the electronic speed and impact control
dial (g) to a medium or high speed setting.
5. Fit and adjust the side handle (c).
English
12
6. Place the centerdrill on the spot and switch on
the tool. Drill until the core penetrates into the
concrete approximately 1 cm.
7. Stop the tool and remove the centerdrill. Place
the core bit back into the hole and continue
drilling.
8. When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals.
To avoid unwanted breaking away of concrete
around the hole, first drill a hole the diameter of
the centerdrill completely through the structure.
Then drill the cored hole halfway from each side.
9. Always turn the tool off when work is finished
and before unplugging.
Chipping and Chiselling (fig. 1)
1. Insert the appropriate chisel and rotate it by
hand to lock it into one of 24 positions.
2. Set the mode selector switch (f) to the
hammering only position.
3. Set the electronic speed and impact control
dial(g).
4. Fit and adjust the side handle (c).
5. Turn the tool on and start working.
6. Always turn the tool off when work is finished
and before unplugging.
MAINTENANCE
Your DeWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
This machine is not user-serviceable. Take the
tool to an authorised DeWALT repair agent after
approximately 150 hours of use. If problems occur
before this time, contact an authorised DeWALT
repair agent.
Brushes (fig. 3)
The carbon brushes are not user-serviceable. Take
the tool to an authorized DeWALT repair agent.
The yellow brushwear indicator LED (s) lights up
when the carbon brushes are nearly worn out. After
a further 8 hours of use or after the brushes have
completely worn out, the motor will automatically be
shut offf.
Tool maintenance needs to be carried out as soon
as the service indicator (r) lights up.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DeWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DeWALT, recommended
accessories should be used with this
product.
Various types of SDS Max
®
drill bits and chisels are
available as an option.
Consult your dealer for further information on the
appropriate accessories.
English
13
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your D
eWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products
and packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DeWALT provides a facility for the collection and
recycling of DeWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
DeWALT office at the address indicated in this
manual. Alternatively, a list of authorised DeWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
14
SDS MAX
®
D25721 D25722 D25723 D25761 D25762 D25763 D25871
DEWALT D E WALT
D25721 D25722 D25723 D25761 D25762 D25763 D25871
220 220 220 220 220 220 220
1 1 1 1 1 1 1
1350 1400 1400 1500 1500 1500 1400
1.5–15 1.5–15 1.5–15 3–18 3–18 3–18 1.5–15
12–48 12–48 12–48 18-52 18-52 18-52 –
40–115 40–125 40–125 40–150 40–150 40–150 –
25–40 25–45 25–45 28–48 28–48 28-48 –
24 24 24 24 24 24 24
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
SDS Max
®
8.7 9.1 9.1 9.9 9.9 9.9 8.0
a)
1)
15
2)
3)
b)
1)
2)
3)
4)
5)
6)
RCD
RCD
C)
1)
2)
3) /
4)
5)
6)
7)
d)
1)
2)
3)
4)
5)
6)
7)
16
e)
1)
•
•
•
–
–
–
– /
40
80
LED
LED
LED
LED
1
(w)
2014 XX XX
1 D25721 D25722 D25723 D25761
D25762 D25763
1 (D25871)
1
1 K
1 D25871
1
•
•
1A1B2A2B
a. D25721 D25722 D25723
D25761 D25762 D25763
(D25871)
b. D25721 D25722 D25723
D25761 D25762 D25763
17
c.
d.
e.
f.
g.
h.
i.
j.
k.
l.
m.
n.
o.
p.
D25721 D25722 D25723 D25761 D25762 D25763
D25871
•
D25722 D25723 D25761 D25762 D25763
1
3
(g)
–
–
–
(CTC) 3 D25722/D25761/D25762
(CTC)
40
80
(UTC) D25723/D25763
(UTC)
LED 3
LED (s)
8
18
D25721 D25722 D25723 D25761 DD25762 D25763
(b)
LED (r)
(UTC)
LED (r)
D25871
LED (r)
1
(d)
DEWALT IEC 60745
DEWALT
3
1.5 30
OFF
2A 2B
(c)
D25721 D25722 D25723 D25761 D25762 D25763
2A
1. (j) (l) (n)
(k) (m)
2. (i) (h)
3. (c) (k)
4.
20
5. (h)
D25871 2B
1. (p)
2. (j)
(y)
3. (c)
4.
5. (p)
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
