D25810
D25811
Final Page size: A5 (148mm x 210mm)
B
Copyright DeWALT
English 3
8
1
Fig. A
Fig. B Fig. C
1
6
2
3 4
5
7
8
3
2
9
78
78
D25810
D25811
9
A
B C
* Not included for TWZZ
* If need side handle, please purchase the
proper service part: N535058
N535058
2
Fig. E
Fig. D
5
4
E
D
* Not included for TWZZ
ENGLISH
3
1) Work Area Safety
a ) Keep work area clean and well lit. Cluttered or dark
areas inviteaccidents.
b ) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust orfumes.
c ) Keep children and bystanders away while operating
a power tool. Distractions can cause you to losecontrol.
2) Electrical Safety
a ) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of
electricshock.
b ) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if
your body is earthed orgrounded.
c ) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electricshock.
d ) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electricshock.
e ) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electricshock.
f ) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electricshock.
3) Personal Safety
a ) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personalinjury.
b ) Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask,
non‑skid safety shoes, hard hat or hearing protection used
for appropriate conditions will reduce personalinjuries.
c ) Prevent unintentional starting. Ensure the switch
is in the off position before connecting to power
source and/or battery pack, picking up or carrying
Technical Data
D25810 D25811
Voltage Vac 220-240 220-240
Frequency Hz 50/60 50/60
Power Input W1050 1050
No-load beats per minute bpm 3150 3150
Single impact energy (EPTA 05/2009) J7.1 7.1
Tool holder SDS-Max 17mm-HEX
Collar diameter mm 76 76
Weight (including handle) kg 5.6 5.7
WARNING: To reduce the risk of injury, read the
instruction manual.
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.
CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Denotes risk of electricshock.
Denotes risk offire.
General Power Tool Safety Warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains‑
operated (corded) power tool or battery‑operated (cordless)
powertool.
English (original instructions)
HEAVY-DUTY CHIPPING HAMMER
D25810, D25811
Congratulations!
You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the
most reliable partners for professional power toolusers.
4
ENGLISH
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invitesaccidents.
d ) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personalinjury.
e ) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpectedsituations.
f ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can be
caught in movingparts.
g ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust‑relatedhazards.
h ) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe
injury within a fraction of asecond.
4) Power Tool Use and Care
a ) Do not force the power tool. Use the correct power
tool for your application. The correct power tool
will do the job better and safer at the rate for which it
wasdesigned.
b ) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must berepaired.
c ) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the
power toolaccidentally.
d ) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrainedusers.
e ) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained powertools.
f ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier tocontrol.
g ) Use the power tool, accessories and tool bits, etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardoussituation.
h ) Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpectedsituations.
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool ismaintained.
Additional Safety Instructions for Chipping
Hammers
• Wear ear protectors. Exposure to noise can cause
hearingloss.
• Use auxiliary handle(s),if supplied with the tool. Loss of
control can cause personalinjury.
• Hold power tools by insulated gripping surfaces when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live” and
could give the operator an electricalshock.
• Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or
against your body is unstable and may lead to loss ofcontrol.
• Wear safety goggles or other eye protection. Hammering
operations cause chips to fly. Flying particles can cause
permanent eye damage. Wear a dust mask or respirator
for applications that generate dust. Ear protection may be
required for mostapplications.
• Keep a firm grip on the tool at all times. Do not attempt
to operate this tool without holding it with both hands. It
is recommended that the side handle be used at all times.
Operating this tool with one hand will result in loss of control.
Breaking through or encountering hard materials such as
re‑bar may be hazardous as well. Tighten the side handle
securely beforeuse.
• Do not operate this tool for long periods of time. Vibration
caused by hammer action may be harmful to your hands and
arms. Use gloves to provide extra cushion and limit exposure
by taking frequent restperiods.
• Do not recondition bits yourself. Chisel reconditioning should
be done by an authorized specialist. Improperly reconditioned
chisels could causeinjury.
• Wear gloves when operating tool or changing bits. Accessible
metal parts on the tool and bits may get extremely hot
during operation. Small bits of broken material may damage
barehands.
• Never lay the tool down until the bit has come to a complete
stop. Moving bits could causeinjury.
• Do not strike jammed bits with a hammer to dislodge them.
Fragments of metal or material chips could dislodge and
causeinjury.
• Slightly worn chisels can be resharpened bygrinding.
• Keep the power cord away from the bit. Do not wrap the
cord around any part of your body. An electric cord wrapped
around a spinning bit may cause personal injury and loss
ofcontrol.
5
ENGLISH
Residual Risks
The following risks are inherent to the use of chipping hammers:
• Injuries caused by touching the rotating parts or hot parts of
thetool.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
• Risk of squeezing fingers when changing theaccessory.
• Health hazards caused by breathing dust developed when
working in concrete and/ormasonry.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot
duringoperation.
• Risk of personal injury due to prolongeduse.
WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your DeWALT tool is double insulated in accordance
with IEC62841; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the DeWALT
serviceorganisation.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm2; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
Package Contents
The package contains:
1 Chipping hammer
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred duringtransport.
• Take the time to thoroughly read and understand this manual
prior tooperation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Date Code Position (Fig. A)
The date code 9, which also includes the year of manufacture,
is printed into thehousing.
Example:
2023 XX XX
Year of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury couldresult.
1 Trigger switch
2 Side handle(Not included for TWZZ)
3 Front Barrel (Collar)
4 Mode selector dial
5 Mode selector release button
6 Main handle
7 Tool holder
8 Sleeve
Intended Use
Your chipping hammer has been designed for professional
chiseling and chippingapplications.
DO NOT use under wet conditions or in the presence of
flammable liquids orgases.
Your chipping hammer is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with thisproduct.
Active Vibration Control
For best vibration control, hold the tool as described in Proper
Hand Position.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make the
tool chip faster and active vibration control will not engage.
6
ENGLISH
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start‑up
can cause injury.
Side Handle (Fig.A–B Not included for TWZZ)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximizecontrol.
The side handle2 clamps to the front of the gear case and may
be rotated 360˚ to permit right- or left-hand use.
Mounting the Straight Side Handle (Fig. B)
1. Widen the ring opening of the side handle 2 by rotating it
anti-clockwise.
2. Place the assembly onto the chipping hammer putting
the nose of the tool through the steel ring 9 and onto the
collar3 past the tool holder and sleeve.
3. Rotate the side handle assembly to the desired position.
4. Lock the side handle mounting assembly in place by
securely tightening the handle 2 rotating it clockwise so
that the assembly will not rotate.
Bit and Bit Holder
WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage barehands.
WARNING: Do not attempt to tighten or loosen drill bits
(or any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may occur.
The chipping hammer can be fitted with various chisel bits
depending on the desired application. Use sharp bitsonly.
Inserting and Removing SDS-Max Bits (Fig. C)
D25810
NOTE: Accessories and attachments used must be lubricated
around the SDSfitment before installation.
1. Pull back the locking sleeve 8 and insert the bit shank. The
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
NOTE: The bit needs to move several centimeters in and out
of the tool holder 7 when properly engaged.
4. To remove the bit, pull back the locking sleeve and pull the
bitout.
Inserting and Removing 17 mm HEX Bits
(Fig. C)
D25811
This tool uses 17mm HEX accessories. We recommend to use
professional accessories only.
1. Clean and grease the bit shank.
2. Insert the bit shank into the tool holder 7.
3. Push the bit further into the tool and turn it slightly until it
fits into theslots.
4. Ensure the bit is properly engaged.
NOTE: The bit needs to move several centimeters in and out
of the tool holder 7 when properly engaged.
To remove the bit, pull back the locking sleeve and pull the
bitout.
Bit Position Adjustment
Turn the mode selector to bit adjustment icon (Refer to Mode
Selection) to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel.
NOTE: After finding the desired position, slightly maneuver
the chisel bit back and forth to ensure the chisel is
properlyengaged.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicableregulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start‑up
can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Proper hand position requires one hand on the mounted side
handle, with the other hand on the mainhandle.
Mode Selection (Fig.E)
WARNING: Do not select the operating mode when the
tool isrunning. Tool must come to a complete stop before
activating the mode selector button or damage to the tool
may result.
Your tool is equipped with a mode selector dial 4 to selectthe
mode appropriate to desired operation.
7
ENGLISH
Symbol Mode Application
Bit
Adjustment Chisel bit position adjustment
Hammering/
Chipping
Light chipping, chiseling
anddemolition
To select a mode:
1. Depress the mode selector release button5.
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
NOTE: The arrow on the mode selector dial4 must be pointing
at a mode symbol at all times. There are no operable positions
inbetween.
Performing an Application (Fig.A, E)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly.
NOTE: Operating temperature of this tool is 19˚ to 104˚ F (-7 to
+40˚ C). Using the tool outside of this temperature range will
decrease the life of the tool.
1. Insert the appropriate chisel and rotate it by hand to lock it
into the desired position.. Refer to Bit and Bit Holder.
2. Using the mode selector dial4, selectchipping mode .
Refer to Mode Selection.
3. Adjust the side handle2 asnecessary. Refer to Mounting
the Straight Side Handle.
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch1.
6. To stop the hammer, release the switch.
MAINTENANCE
Your DeWALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regularcleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start‑up
can cause injury.
Lubrication
Your power tool requires no additionallubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non‑metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only DeWALT recommended
accessories should be used with thisproduct.
Various types of SDS-Max and 17mm HEX bits and chisels are
available as anoption. Accessories and attachments used must
be regularly lubricated around the fitment.
Consult your dealer for further information on the
appropriateaccessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
8
c )
請等待兒童和旁觀者離開之後才操縱電動工
具。分心會導致您疏於控制。
2） 電氣安全
a )
電動工具插頭必須與插座相符。切勿以任何方
式改裝插頭。需接地的電動工具不能使用任何
配接器插頭。使用未經改裝的插頭與相符的插
座可降低觸電風險。
b )
避免人體接觸接地表面，如管道、散熱片、爐灶
和冰箱。若您的身體接地，會增加觸電的風險。
c )
不得將電動工具暴露在雨中或潮濕環境中。水
進入電動工具會增加觸電風險。
d )
切勿濫用電線。請勿使用電線來搬運、拉動電動
工具或拔出插頭。讓電線遠離熱、油、銳邊和活
動部件。受損或纏繞的電線會增加觸電危險。
e )
若要在戶外使用電動工具，請使用適合戶外使
用的延長電線。採用適合室外使用的電線可降
低觸電危險。
f )
若必須在潮濕環境中操作電動工具，請使用受
漏電保護器(RCD) 保護的電源供應器。使用RCD
可降低觸電風險。
3） 人身安全
a )
保持警覺；在操作電動工具時，請留意所執行的
操作並按照一般的程式執行。請勿在疲倦或在
受到毒品、酒精或藥品的影響時使用電動工具。
操作電動工具時，一時的注意力分散可能會導
致嚴重人身傷害。
b )
使用個人防護裝置。始終佩戴護目裝置。防護
設備 (例如在適當條件下使用的防塵面具、防
滑安全鞋、安全帽或聽力保護裝置) 可減少人
身傷害。
c )
避免意外啟動。連接電源及/或電池組、舉抬或搬
運電動工具之前，請確定開關處於關閉位置。若
搬運電動工具時將手指放在開關上，或者在電
動工具開關開啟時將插頭插入電源插座，這兩
種行為都會引發事故。
d )
啟動電動工具之前，請卸下所有的調整鑰匙或
扳手。遺留在電動工具旋轉部件上的扳手或鑰
匙會導致人身傷害。
e )
不要過度伸張雙手。時刻注意腳下與身體的平
衡。如此可在意外情況下更好地控制電動工具。
f )
適當穿著。請勿穿寬鬆衣服或佩戴飾品。讓您的
頭髮、衣服和手套遠離活動部件。寬鬆衣服、佩
飾或長髮可能會捲入活動部件中。
g )
若配備用於連接排屑裝置、集塵設備的裝置，請
確定正確連接和使用這些裝置。使用集塵設備
可減少與粉塵有關的危險。
D25810 D25811
110 110
60 60
1050 1050
/bpm 3150 3150
(EPTA 05/2009)
7.1 7.1
SDS-Max 17mm-HEX
76 76
5.6 5.7
/
請保存所有警告與指示以備將來查閱。
以下列示所有警告中的術語「電動工具」是指電源驅動（插電）電動
工具或電池驅動（充電）電動工具。
1） 工作場地安全
a )
請保持工作場地清潔明亮。混亂或黑暗的場地
會引發事故。
b )
請勿在易爆環境，如有易燃液體、氣體或粉塵的
環境中操作電動工具。電動工具產生的火花可
能會引燃粉塵或煙霧。
D25810, D25811
DEWALT DEWALT
/。
9
h )
請勿因頻繁使用而對工具特別熟悉，讓你變得
自滿而忽略工具的安全原則。粗心操作可以在
片刻間造成嚴重傷害。
4) 電動工具的使用與注意事項
a )
請勿超負荷使用電動工具。請根據您的應用使
用正確的電動工具。若使用的電動工具正確無
誤，該工具能以設計額定值更有效、更安全地執
行工作。
b )
若開關不能開啟或關閉電源，切勿使用該電動
工具。若開關無法控制電動工具，則電動工具存
在危險，必須予以維修。
c )
在執行任何調整、更換配件或儲存工具之前，
必須從電源上拔掉插頭及/或卸下電池組。此類
防護性安全措施可降低電動工具意外啟動的
風險。
d )
將閒置的電動工具儲存在兒童無法接觸的地
方，並且不要讓不熟悉電動工具或對這些使用
指示不瞭解的人員操作電動工具。未經訓練的
使用者操作電動工具會發生危險。
e )
維護電動工具。檢查活動部件是否對準或卡住、
是否存在任何破損情況，或任何能影響電動工
具運行的其他情況。若有損毀，必須在使用之前
修理電動工具。許多事故都是由於電動工具欠
缺維護所導致。
f )
保持切削工具鋒利和清潔。妥善維護、刀刃鋒利
的刀具卡住的可能性更低，更易於控制。
g )
使用電動工具、配件和工具刀頭等時，請遵循這
些指示使用，且指示須包含工作環境和所要執
行工作的注意事項。若使用電動工具執行與設
計用途不相符的操作，會導致危險。
h )
手柄和抓握表面都應保持乾燥、清潔及遠離油
脂。光滑手柄和抓握表面不便於在意外情況下
對工具進行安全處理與控制。請使用原廠的電
動工具電池組。使用其他非原廠的電池組會導
致人身傷害和火災危險。不使用電池組時，請將
其遠離如迴紋針、硬幣、鑰匙、釘子、螺絲以及其
他可連通電池兩極的金屬物品。將電池兩極短
路會導致灼傷或火災。濫用電池的情況下，液體
會從電池中噴出；避免與液體接觸。若不小心接
觸液體，請用清水沖洗。若液體噴濺到眼睛上，
沖洗之後還應進行治療。從電池噴出的液體會
刺激皮膚或造成灼傷。請勿使用已經損壞或改
動的電池組或工具。損壞或改動的電池可能表
現出不可預計的行為，導致火災、爆炸或傷害風
險。請勿讓電池組或工具暴露於火中或過高溫
度的環境中。暴露於火中或溫度超過 130°C的環
境中可能導致爆炸。請遵循所有充電說明，請勿
在說明中規定的溫度範圍以外的環境對電池組
或工具充電。不當或在指定範圍以外的溫度下
充電，可能導致電池損壞並增加火災風險。
5) 檢修
a )
本電動工具必須由合格的維修人員並只採用相
同的原廠零件來執行檢修。這將確保電動工具
的安全性。
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
/
•
•
•
30mA
10
DEWALT IEC62841
DEWALT
1.5
30
1
1
•
•
( A)
9
2023 XX XX
A
1
2
3
4
5
6
7
8
•
•
(OFF)
A–B
2 360˚
B
1. 2
2. 9
3
3.
4. 2
11
SDS-Max C
D25810
SDS
1. 8
2.
3.
7
17mm C
D25811
17mm
1.
2. 7
3.
4.
7
(OFF)
( D)
E
4
/
1. 5
2.
4
( AE)
19˚ 104˚ F -7
+40˚ C
1.
2. 4
3. 2
4. /
5. 1
6.
DEWALT
(OFF)
12
DEWALT
DEWALT
SDS-Max 17mm
www.2helpU.com
: ()
: 33 2
: 02-28341741
:
: 137
: 02 - 29994633
13
Declaration of the Presence Condition of the Restricted Substances Marking
D25811
Equipment name Type designation (Type)
Unit
Restricted substances and its chemical symbols
Lead
(Pb)
Mercury
(Hg)
Cadmium
(Cd)
Hexavalent
chromium
(Cr+6)
Polybrominated
biphenyls
(PBB)
Polybrominated
diphenyl ethers
(PBDE)
〇〇〇〇〇〇
〇〇〇〇〇〇
〇〇〇〇〇〇
〇〇〇〇〇〇
〇〇〇〇〇〇
〇〇〇〇〇〇
1.0.1 wt %0.01 wt %
Note 1Exceeding 0.1 wt % and exceeding 0.01 wt % indicate that the percentage content of the
restricted substance exceeds the reference percentage value of presence condition.
2.
Note 2 indicates that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence.
3.
Note 3The indicates that the restricted substance corresponds to the exemption.
NA382104 07/2023
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
