3
2
3
4
1
1
Installation Place.
The floor should be sturdy and flat.
Lay the board which has 1cm thickness on the floor if the refrigerator is installed on the carpet, tatami mat,
flooring or PVC sheet flooring which may hollow or discolor.
A location away from direct sunlight and heat is recommended.
A location is not damp and has good air flow.
This will reduce adverse effects to refrigerating power and keep electricity cost down. This will also prevent
the refrigerator from discoloring and rusting.
Clearance around the refrigerator.
To cool efficiently, allow enough space around the refrigerator for radiating heat.
The actual size of the center part of the side of the refrigerator's main body
is slightly larger than the nominal size.
Therefore, allow enough space around the refrigerator taking it into
consideration when installing the refrigerator.
The back of the refrigerator can be placed very close to a wall. If any
vibration sound occurs and/or any discolor/dirt is found on the wall, move
the refrigerator away from the wall.
Adjusting the refrigerator adjustable mount
to keep it level
Left side or right side of the door may be slightly lower
when the surface of the installation place is not level
or either of the left and right leg is sunk in the floor
surface because of the soft floor material and the
addition of food weight.
ψ
This does not affect the refrigerator function. Adjust the
refrigerator adjustable mount to keep it level according
to the procedure listed below if you want to correct it.
Correcting any left/right lean and lifting slightly the
front side of the refrigerator, the door can close easily
and completely.
To remove leg cover, hold both ends of it and pull it
towards to you applying some force.
Turn left and/or right Adjustable mounts to make
the Refrigerator Compartment Door horizontal.
The height of the door will change by 1mm every 1
turn of Adjustable mount.
The adjusted door may lean because it may take
several days until the refrigerator permanently
becomes level after adjusting.
Adjust the refrigerator legs again to keep it level
according to the procedure if this is the case.
Use the optional parts "Door Adjusting Plate" (Parts
No. R-Y6000 500) if the door still leans after that.
Insert the left and right pins of the leg cover into the
leg holes to install the leg cover.
Turn both Adjustable mounts to lower them to the
floor surface and fix them.
2
Required space for right and
left of the refrigerator: 1cm or more
Leg cover
Adjustable mounts
Installation
holes
Pins
1
2
When it is hard to turn the Adjustable mount
Push and turn it with a tool such as a driver.
3
The right side of the
door is lower.
The left side of the
door is lower.
Turn the left Adjustable
mount to lower the left
side of the door.
3
Turn the right Adjustable
mount to lower the right
side of the door.
BEFORE USE
Required space above the
refrigerator: 5cm or more
4
Preparation for an earthquake
has been made properly?
Stickers
Plastic parts
Label
Left/Right
Notes after installation
It may take more than 4 24 hours to fully cool depending on the temperature around the refrigerator or the
amount of the stored food.
Clean the Automatic ice maker using "Ice Maker Cleaning" when using it for the first time. ( Pg. 22)
A series of ice-making procedures which is automatically performed starts after the refrigerator cools
enough. (It may take more than 24 hours to make ice for the first time.
Minimize the number of times of opening and closing the door to cool it quickly.
Allow clearance between each food in each compartment.
It may smell like plastic for the first time. Ventilate the room well to make sure that the room is not filled with
the smell. The smell gradually disappears.
It is recommended to fix the refrigerator to a
sturdy wall or pillar using two "safety belt
against overturning
for refrigerators".
Option: "Safety belt
against overturning
for refrigerators"
(Parts No. R-826CV
300: belt x 1)
Contact your dealer
for details.
Screw x 4
(attached to belt)
Belt
It is not a problem to plug in the
power cord soon after installing
the refrigerator.
Use a wall outlet exclusively when
connecting the power cord.
(Alternating current 110V, rated
15A or more)
It is recommended to ground
the refrigerator to prevent
possible electrical shock.
Never connect the earth wire to the
following places:
Earth terminal
Earth wire
(Copper wire with
diameter of 1.6mm)
Earth installation screws
Contact your dealer to ground the
refrigerator or install an earth leakage circuit
breaker if the refrigerator is installed in
especially damp and humid places.
Option: "Earth wire (2.5m)"
(Parts No. NW-60R6 052)
Water pipe (Danger of electrical shock)
Gas pipe (Danger of explosion)
Telephone line or earth of lightning rod
(Danger when lightning strikes)
Notice
Do not remove the sticker from the back of the refrigerator. This
sticker is necessary to secure the performance and safety
.
Do not remove the plastic parts and label from the bottom
part of the side of the refrigerator.
If you want to install the refrigerator in an hot spring area where
it is exposed to sulfide gas, it may be necessary to apply rust
preventive treatment. Contact your dealer in advance if this is
the case. Any failure caused by the gas will not be covered
under warranty.
Before Use