www.blackanddecker.com
FSMH13E5
ENGLISH 5
简体中文
8
2
3
1
3
4
5
6
7
8
9
12
13
10
11
2
2
3
1
3
4
5
6
7
8
9
12
13
10
11
2
7 14 15 16
A
FSMHI3E5
8
9
B
5
5a
5b
6
C
6
7
D
4
5
10
11
3
4
F
G
1316
13a
E
5
ENGLISH
4
5
FSMH13E5 STEAM MOP
Technical Data
FSMH13E5
Voltage V
ac
220-240V
Power W 1300
Tank Capacity ml 380
Weight kg 1.8
Intended use
Your BLACK+DECKER
TM
FSMH13E5 steam mop has been
designed for sanitising and cleaning sealed hardwood, sealed
laminate, linoleum, vinyl, ceramic tile, stone and marble oors.
This appliance is intended for indoor household use only.
Safety Instructions
t
Warning! Read all Safety,
Maintenance, Service' manual
carefully before operating
this appliance. Read all of this
manual carefully before operat-
ing this appliance.
Safety of others
u This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sen-
sory or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance in a
safe way and understand the hazards
involved.
u Children shall not play with the appli-
ance. Cleaning and user maintenance
shall not be made by children without
supervision.
u If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualied
persons in order to avoid a hazard.
u The plug must be removed from the
socket-outlet before cleaning or main-
taining the appliance.
u The liquid or steam must not be
directed towards equipment contain-
ing electrical components, such as the
interior of ovens.
u The appliance shall not be left unat-
tended while it is connected to the sup-
ply mains.
u The appliance is not to be used if it
has been dropped, if there are visible
signs of damage or if it is leaking.
u Keep the appliance out of reach of
children when it is energized or cooling
down.
Labels on appliance
The following pictograms along with the
date code are shown on the appliance.
CAUTION Hot Steam
t
Warning! To reduce the risk of
injury, the user must read the
instruction manual.
Features
1. On/off switch
2. Steam operate button
3. Water tank access tab
4. Water tank
5. Steam head connector
6. Steam head
7. Steam head cleaning pad
8. Handle connector button
9. Handle
10. Cable tidy hook
11. Grip
12. Power cable
13. Accessory adaptor
14. Small brush (plastic bristles)
15. Small squeegee
16. Grout brush
6
ENGLISH
Assembly
@
Warning! Before attempting any of the following
instructions, make sure that the appliance is
switched off and unplugged and the appliance is
cold and does not contain any water.
Attaching the handle (Fig. B)
u Slide the bottom end of the handle (9) into the top end of
the steam mop body until the handle connector button (8)
clicks into place.
Attaching the steam head (Fig. C)
u Connect the steam mop body to the steam head (6) via
the steam head connector (5), ensuring the connection
button (5a) clicks into place in the the opening (5b).
Attaching a cleaning pad (Fig. D)
Replacement cleaning pads are available from your
BLACK+DECKER dealer :- (cat no. FSMP20-A9).
u Place a cleaning pad (7) on the oor with the velcro 'loop'
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(7).
Caution: Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop. Do not wear slippers or
open toed footwear.
u Return the handle (9) to the upright position and turn the
steam mop 'OFF'.
u Wait until the steam mop cools down (approximately 5
minutes).
u Lift the steam mop away from the cleaning pad freeing it
from the velcro fastening.
Caution! Always place your steam mop with the handle (9)
supported in the upright position when stationary and make
sure the steam mop is turned off when not in use.
Using as a hand held unit
u Disonnect the hand held unit from the steam head by
pushing the connection button (5a) gure C.
u Remove the handle (9) from the hand held unit by pushing
the handle connector button (8) gure B.
Fitting accessories (Fig. E)
u Fit the accessorie adaptor (13) into the main body of the
unit ensuring the button (13a) clicks into the relevant
opening.
u Attach the required accessorie to the accessorie adaptor
(13) and twist clockwise to lock into place.
Filling the water tank (Fig. F)
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
u Open the water tank access tab (3).
u Fill the water tank (4) with water.
Warning! Your water tank has a 380ml capacity. Do not over
ll the tank.
u Replace the water tank access tab.
Note! Ensure the water tank access tab is rmly secured.
Note! Do not use chemical cleaners with your steam mop
water tank.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro bre pad tted and a continuous run time
of 90 seconds.
Switching on and off
u To switch the appliance on, press the ON/Off button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
u Press the steam operation button (2). This will operate the
pump and the unit will begin to produce steam.
u To stop steam generation, turn the steam operation button
(2) to off. This will maintain power to the boiler for quicker
start up.
u To switch the appliance off, press the ON/Off button (1).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (9) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When rst lled or after running dry, it can take up to 45
seconds for steam to be produced.
Hints for optimum use
General
Caution: Never use the steam mop without rst attaching a
cleaning pad.
u Always vacuum or sweep the oor before using the steam
mop.
u The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at a
time.
7
ENGLISH
u Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum oors, you
can pre-treat with a mild detergent and some water before
using the steam mop.
Steam Cleaning
u Place a cleaning pad (7) on the oor with the velcro 'loop'
side facing up.
u Lightly press the steam mop down onto the cleaning pad
(7).
u Connect the steam mop to the mains.
u Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
u Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When rst lled or after running dry, it can take up to 45
seconds for steam to be produced.
u It takes a few seconds for steam to enter the cleaning pad.
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
u Push and pull the steam mop slowly across the surface to
thoroughly steam clean each section.
u When you have nished using the steam mop, return
the handle (9) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately ve minutes).
Caution! It is important to monitor the water level in the water
tank (4). To rell the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, rell the water tank (4).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (9) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
After use (Fig. G)
u Turn the steam mop 'OFF'. turn the steam operation
button (2) to off and then press the ON/OFF button (1).
u Wait until the steam mop cools down.
u Unplug the steam mop from the electrical wall outlet.
u Empty the water tank.
u remove the cleaning pad (7) and wash it ready for next
use.
u Wrap the power supply cable around the tidy hook (10).
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Problem Step Possible solution
The steam mop is not
turning on
1. Check the unit is
plugged in at the wall
socket.
2. Check the unit is
switched on using the
ON/OFF switch (1)
The steam mop is not
producing steam
3. Check the water tank
(4) is full .
NOTE: When rst lled
or after running dry it
can take up to 45
seconds for steam to
be produced.
4. Check the steam
generation button is in
the ON position (2).
5. The steamer is
equipped with a
thermostat and a
thermal cut-out. If for
any reason the steamer
overheats it will switch
off. If this happens turn
off and unplug the
steamer, allow to cool
for 2 to 4 hours and
re-try.
Service Information
BLACK+DECKER offers a full network of company-owned
and authorized service locations throughtout Asia. All
BLACK+DECKER Service Centers are staffed with trained
personnel to provide customers with efcient and reliable
product service.
Whether you need technical advice, repair, or genuine factory
replacement parts, contact the BLACK+DECKER location
nearest to you.
NOTE
u BLACK+DECKER’s policy is one of continuous improve-
ment to our products and, as such, we reserve the right to
change product specications without prior notice.
u Standard equipment and accessories may vary by country.
u Product specications may differ by country.
u Complete product range may not be available in all
countries. Contact your local BLACK+DECKER dealers for
range availability.
8
简体中文
FSMH13E5 蒸汽拖把
技术参数
FSMH13E5
电压 伏特
交流
220-240 伏特
功率 瓦
1300
水箱容量 毫升
380
重量 千克
1.8
设计用途
BLACK+DECKER
TM
FSMH13E5 蒸汽拖把设计用于
清洁与清洗密封实木地板、密封复合地板、油地
毡地板、乙烯基地板、瓷砖地板，石地板及大理石
地板。本设备仅适用于室内家庭用途。
安全说明
t
警告！使用设备前，请
仔细阅读“安全、维护、
保养”手册的所有内容。
使用设备前，请仔细阅读
本手册。
他人安全
在有他人监督的情况下，或在
接受过安全使用该产品的指导
并已了解了可能存在的危险的情
况下，
8 岁或以上的小孩，以及
身体、感官或精神较差的人员，
或者对该类产品缺少使用经验
和认识的人员，也可以使用本
产品。
儿童不得耍玩本设备。在没有他
人监督的情况下，禁止儿童使用
本设备或对其进行维护保养。
如果电源线损坏，必须让制
造商、检修代理或类似合格人
员更换以避免发生危险。
在清洁或维护设备之前，必须从
插座上拔下插头。
液体或蒸汽不得朝向包含电气部
件的设备，例如炉的内部。
设备连接到电源时，不得无人
看管。
如果设备掉落，或者有明显的
损坏迹象或泄漏，则不得使用
设备。
在设备通电或冷却时，将设备放
在儿童接触不到的地方。
设备上的标签
设备上显示下列图形和日期码。
警示 热蒸汽
t
警告！为减少受伤风险，
用户须阅读使用手册。
部件名称
1. On/Off 开关
2. 蒸汽操作按钮
3. 水箱盖
4. 水箱
5. 蒸汽头连接器
6. 蒸汽头
7. 蒸汽头清洁垫
8. 手柄连接器按钮
9. 手柄
10. 电源线整理钩
11. 手柄
12. 电源线
13. 附件适配器
14. 小型毛刷（塑料刷毛）
15. 小型橡胶清洁器
16. 灌浆刷
9
简体中文
组装
@
警告！进行如下任何操作之前，请确保
关闭设备开关、拔下设备插头、设备处
于冷却状态并且不含水。
安装手柄（图 B）
将手柄 (9) 的底端向蒸汽拖把机身的顶端滑动，
直至手柄连接器按钮 (8) 卡入到位。
安装蒸汽头（图 C）
通过蒸汽头连接器 (5) 将蒸汽拖把主体连接到蒸
汽头 (6)，确保连接按钮 (5a) 卡入定位槽 (5b) 中。
安装清洁垫（图 D）
BLACK+DECKER
代理商均提供备用清洁垫（货号：
FSMP20-A9）。
将清洁垫
(7) 置于地板上，魔术扣贴“环形”面
朝上。
将蒸汽拖把往清洁垫
(7) 上轻压。
警示：蒸汽拖把处于静止状态时，切记使手柄
(9)
保持竖直位置；未使用蒸汽拖把时，请确保将其开
关关闭。
拆卸清洁垫
小心！给蒸汽拖把更换清洁垫时，请务必穿上合适
的鞋子。请勿穿拖鞋或露趾鞋。
将手柄
(9) 恢复到竖直位置，关闭蒸汽拖把电源
开关。
等待蒸汽拖把冷却（约
5 分钟）。
分开魔术贴，向上提起蒸汽拖把，从清洁垫上
取下。
警示！蒸汽拖把处于静止状态时，切记使手柄
(9)
保持竖直位置；未使用蒸汽拖把时，请确保将其开
关关闭。
将其用作手持设备
如图 C 所示，按下连接按钮 (5a)，将手持设备
与蒸汽头断开。
所图
B 所示，按下手柄连接器按钮 (8)，从手持
设备卸下手柄 (9)。
安装配件 （图 E）
将附件适配器 (13) 装入本机的主体，确保按钮
(13a) 卡入相应的定位槽。
将所需附件连接到附件适配器
(13) 上并顺时针
旋转以锁定到位。
给水箱加水（图 F）
注意！请给水箱加装清洁的自来水。
注意！如果您所在地区的自来水水质较硬，建议您
使用去离子水。
打开水箱盖
(3)。
给水箱
(4) 加水。
警告！本水箱的容量为
380 毫升。请勿超过水箱的
最高水位线。
更换水箱盖。
注意！确保水箱盖已牢牢盖紧。
注意！请勿将蒸汽拖把水箱与化学清洁剂一起使用。
使用
重要信息！若按照本手册中的说明操作并使用装配
的微纤维垫连续运行超过 90 秒，本设备的灭菌率将
达 99.9%。
开启和关闭
要启动设备，请按下开/关按钮 (1)。蒸汽拖把需
要大约 15 秒钟进行加热。
按下蒸汽操作按钮
(2)。这将使水泵开始运作，
并使设备产生蒸汽。
要停止产生蒸汽，请将蒸汽操作按钮
(2) 转至关
闭位置。这将保持发热体的电力以加速启动。
要关闭设备，请按下开/关按钮
(1)。
小心！禁止让蒸汽拖把长时间停留在任一工作表
面上。
蒸汽拖把处于静止状态时，切记使手柄
(9) 保持
竖直位置；未使用蒸汽拖把时，请确保将其开关
关闭。
小心！使用后，务必清空蒸汽拖把。
注意！刚注入水或水份耗尽后，可能需要最长
45
秒时间来产生蒸汽。
最佳使用提示
一般原则
警示：禁止在未安装清洁垫的情况下使用蒸汽拖把。
使用蒸汽拖把前，请务必使用吸尘器或扫把将地
板上的灰尘清除干净。
本产品最简单的使用方法就是将手柄倾斜至
45°
角，慢慢清洁，每次只清洁一小片地方。
请勿将蒸汽拖把与化学清洁剂一起使用。要清除
乙烯基地板或油地毡地板上的顽固污渍，可在
使用蒸汽拖把前，用温和洗涤剂和适量的水进
行处理。
10
简体中文
蒸汽清洁
将清洁垫 (7) 置于地板上，魔术扣贴“环形”
面朝上。
将蒸汽拖把往清洁垫
(7) 上轻压。
将蒸汽拖把连接至主电源。
按下开/关按钮
(1)。蒸汽拖把需要大约 15 秒钟
进行加热。
按下蒸汽操作按钮
(2)。数秒后，蒸汽将从蒸汽
头中涌出。
注意！刚注入水或水份耗尽后，最多可能需要
45
秒来产生蒸汽。
蒸汽需要几秒钟时间进入清洁垫。完成以上步
骤后，蒸汽拖把将能轻松在待清洁/清洗的表面
上滑动。
在表面上慢慢推拉蒸汽拖把，用蒸汽彻底清洁地
板的各个角落。
用完蒸汽拖把后，将手柄
(9) 返回到直立位置，
确保稳固支撑并将其关闭。等待蒸汽拖把冷却
(约 5 分钟)。
警示！使用时，监控水箱
(4) 水位非常重要。要重
新装满水箱并继续清洁/清洗，请将拖把直立放置，
确保手柄稳固支撑，并关闭蒸汽拖把。从墙面插座
上拔下工具插头，然后重新注满水箱 (4)。
警示！禁止让蒸汽拖把长时间停留在任一工作表
面上。蒸汽拖把处于静止状态时，切记使手柄
(9)
保持竖直位置；未使用蒸汽拖把时，请确保将其开
关关闭。
使用后（图 G）
关闭蒸汽拖把。 关闭蒸汽操作按钮 (2)，然后按
下开/关按钮 (1)。
等待蒸汽拖把冷却。
从墙面插座上拔下蒸汽拖把插头。
清空水箱。
取下并清洗清洁垫
(7)，以备下次使用。
将电源线缠绕在整理钩上
(10)。
故障排除
如果设备似乎无法正常运行，请按照以下说明进
行操作。如果仍不能解决问题，请联系您当地的
BLACK+DECKER 维修代理。
问题 步骤 可能的解决方案
蒸汽拖把没有启动
1.
检查设备是否已插入墙
壁插座。
2. 使用 ON/OFF 开关 (1) 检
查设备是否已打开
蒸汽拖把不产生
蒸汽
3. 检查水箱 (4) 是否已满。
注：刚注入水或水份耗
尽后，可能需要最长
45
秒时间来产生蒸汽。
4.
检查蒸汽生成按钮是否处
于开启位置
(2)。
5.
蒸汽机配备恒温器和热切
断器。如果蒸汽机因任何
原因出现过热情况，将会
自动关闭。如果发生这种
情况，请关闭并拔下蒸汽
机插头，让其冷却
2 至 4
小时后重新尝试。
服务信息
BLACK+DECKER
提供覆盖整个亚洲的公司隶属和
授权服务地点。所有 BLACK+DECKER 服务中心都
具有训练有素的人员，为客户提供高效和可靠的产
品服务。
不论您是需要技术建议、维修或原厂替换部件，
请联系最靠近您的
BLACK+DECKER 地点。
备注
BLACK+DECKER 的政策是持续改进我们的产
品，因此，我们保留随时更改产品规格的权利，
恕不另行通知。
标准设备和附件可能会因国家（地区）而异。
不同国家（地区）的产品规格也可能会有所
不同。
并非所有的国家（地区）都可提供完整的产品
系列。有关各产品系列的供货情况，请联系您当
地的
BLACK+DECKER 代理商。
制造商：百得美国公司
地 址：701 E Joppa Rd, TW050 MD21286,
Towson, 美国
产 地：江苏苏州
N596481
04/2018
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
