BLACK+DECKER FSMH1321 ユーザーマニュアル

ブランド: BLACK+DECKER

モデル: FSMH1321

タイプ: ユーザーマニュアル

www.blackanddecker.com

3 4

FSMH1321

ENGLISH 5

简体中文 10

11a

19a

16a

22 20

22a

20a

OFF

FSMH1321 STEAM MOP

Technical Data

FSMH1321

Voltage V

220-240V

Power W 1300

Tank Capacity ml 500

Weight kg 2.7

Intended use

Your BLACK+DECKER

FSMH1321 steam mop has been

designed for sanitising and cleaning sealed hardwood, sealed

laminate,linoleum,vinyl,ceramictile,stoneandmarbleoors.

This appliance is intended for indoor household use only.

Safety Instructions

Warning! Read all Safety,

Maintenance, Service' manual

carefully before operating

this appliance. Read all of this

manual carefully before operat-

ing this appliance.

Labels on appliance

The following pictograms along with the

date code are shown on the appliance.

CAUTION Hot Steam

Water dripping when used

upside down

Steam escapes from all

sides

Do not leave unsuper-

vised with young children

Hand wash only

Features

This appliance includes some or all of the following features.

1. On/off switch

2. Autoselect

dial

3. Hand held steam unit handle

4. Filler cap

5. Hand held steam unit

6. Hand grip

7. Top cable tidy hook

8. Main handle

9. Bottom cable tidy hook

10. Hand held steam unit release button

11. Main body

12. Floor cleaning head

13. Floor cleaning pad

14. Floor cleaning pad release tab

15. Hanging Bracket

16. Steam hose

ENGLISH

steam mop 'OFF'.

u Wait until the steam mop cools down (approximately 5

minutes).

u Lift the steam mop away from the cleaning pad freeing it

from the velcro fastening.

Caution! Never leave the steam mop in one spot on any

surface for any period of time.

Always place the steam mop with the handle (8) supported in

the upright position when stationary and make sure the steam

mop is turned off when not in use.

Filling the water tank (Fig. M)

Note! Fill the water tank with clean tap water (Do not use any

additives or chemicals).

Note! In areas of hard water, the use of de-ionised water is

recommended.

u Openthellercap(4)byippingitup.

u Fill the water tank with water (Do not use any additives or

chemicals).

Warning!Whenlling,detachfrommainunitandmaintainin

a horizontal position.

Warning! Your water tank has a 0.5 litre capacity. Do not over

llthetank.

u Closethellercap(4).

Note! Ensurethellercapisrmlysecured.

Attaching the hose and accessories to the

hand held steam cleaner (Fig. F - K)

Warning! Inspect the seal between the connection point on

the hand held steam cleaner (5) and the steam hose (16)

before each use. If the seal malfunctions or is damaged,

please contact your nearest authorised repair agent. Do not

use the appliance.

Attaching the hose

u Press the steam hose release button (16a) on the steam

hose (16).

u Connect the steam hose (16) to the hand held steam

cleaner (5) and release the steam hose release button

(16a) making sure it clicks into place.

Important! Ensure that the steam hose (16) is securely

connected to the hand held steam cleaner (5). If steam

escapesfromthejoint,thehoseisincorrectlytted.Switchoff,

allowtheunittocoolthenremoveandretthehose.

Attaching accessories (Fig G)

u Align the lugs on the steam nozzle (17) with the recesses

on the accessory.

u Press the accessory onto the steam nozzle (17) and twist

anti-clockwise until the accessory clicks into place.

Important! All accessories, apart from the SteaMitt

(20)

which has its own hose and connector (21), must be attached

to the steam hose (16) for use.

17. Steam nozzle

18. Blue angle brush accessory

(for use on hard to remove stains)

19. Large squeegee accessory

(for use on shower screens / glass / mirrors / clothing /

upholstery)

19a. Large squeegee sock

20. SteaMitt

21. SteaMitt

hose

22. SteaMitt

cleaning pad

23. Adjustable nozzle

Assembly

Warning! Before attempting any of the following

instructions, make sure that the appliance is

switched off and unplugged and the appliance is

cold and does not contain any water.

Attaching the handle (Fig. A)

u Slide the bottom end of the handle (8) into the top end of

the steam mop body (11) until it clicks into place.

Attaching the hand held steam cleaner (Fig. B)

u Holding the back of the steam mop body (11) push the

handheldsteamcleaner(5)rmlyintothesteammop

body (11) making sure it sits correctly over the interface

(11a) and clicks securely into place.

Removing the hand held steam cleaner (Fig. B)

u Push the release button (10) on the main body (11) and lift

the hand held steam cleaner (5) off the interface (11a) and

away from the main body (11).

Attaching a cleaning pad (Fig. C)

Replacement cleaning pads are available from your

BLACK+DECKER dealer .

u Placeacleaningpad(13)ontheoorwiththevelcro'loop'

side facing up.

u Lightly press the steam mop down onto the cleaning pad

(13).

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop

with the handle (8) supported in the upright position when

stationary and make sure the steam mop is turned off when

not in use.

Removing a cleaning pad

Caution! Always wear suitable shoes when changing the

cleaning pad on your steam mop.

Do not wear slippers or open toed footwear.

u Return the handle (8) to the upright position and turn the

ENGLISH

Removing the hose and accessories

Warning! The steam hose (16), Steam nozzle (17) and

accessories become hot during use. Allow the unit and all

accessories to cool before attempting to remove.

Removing an accessory

u Twist the accessory clockwise then pull away from the

hose (16).

Removing the hose

u Press the steam hose release button (16a) on the steam

hose (16) and pull away from the hand held steam unit.

SteaMitt

Your BLACK+DECKER

SteaMitt

has been designed for

sanitising and cleaning tiles, work tops, kitchen surfaces and

bathroom surfaces. This appliance is intended for indoor

household use only.

Attaching the SteaMitt

hose to the hand held

steam unit

Warning! Inspect the seal on the steam nozzle and hose

before each use. If the seal is missing or damaged then

please contact your nearest authorised repair agent. Do not

use the appliance. Inspect the seal on the SteaMitt

and

hose If the seal is missing, damaged or any steam is escaping

then please contact your nearest authorised repair agent.

Do not use the appliance. Ensure there is no blockage or

impedence in the SteaMitt

hose or attachment hose. If any

are detected then please contact your nearest authorised

repair agent. Do not use the appliance.

Fitting a cleaning pad to the SteaMitt

(Fig. H)

Warning! Ensure there is no blockage or impedence in

the steam release vents If any are detected then please

contact your nearest authorised repair agent. Do not use the

appliance.

u Fit the cleaning pad (22) to the SteaMitt

(20) by

attaching the 'loop' velcro strips (22a) on the upper side

of the cleaning pad, to the 'hook' velcro pads (20a) on the

underside of the SteaMitt

(4).Pressdownrmly.

Warning! The SteaMitt

shouldnotbeusedwithoutttinga

cleaning pad.

Note: The SteaMitt

accommodates 4 types of cleaning pads

of varying thickness. Scouring pad (for use on tough stains

and non delicate surfaces), Bathroom pad (for use on taps

and other moulded bathroom surfaces), Standard pad (for use

on all larger surfaces) and Polishing pad (for use on delicate

surfaces).

Warning! Always use the SteaMitt

as shown in

figure M, with your hand inside the protective glove.

Warning! Never attempt to use the SteaMitt

gripping it externally as shown in figure J.

This will result in scalding.

Warning! Avoid using the SteaMitt

in tight corners

asshowningureK.

Warning! Should a problem occur during use,

use the quick release tab to quickly remove the

SteaMitt

fromyourhandasshowningureP.

Warning! Do not use the SteaMitt

on cold glass,

such as windows as damage may be caused by the

sudden change in temperature.

Warning! Never point or direct the mitt at yourself

or any other person.

Note: Variable steam dial is disconnected when the

SteaMitt

isttedandsubsequentlytheowofsteamis

limited.

Use

Important! This unit will kill 99.9% of bacteria and germs

when used in accordance with the instructions in this manual

andwiththemicrobrepadsttedandacontinuousruntime

of 90 seconds.

Switching on and off

u To switch the appliance on, press the ON/Off switch (1).

It takes approximately 15 seconds for the steam mop to

heat up.

u To switch the appliance off, press the ON/Off switch (1).

Note: always have your hand inside the SteaMitt

before you

press the steam button.

Caution! Never leave the steam mop in one spot on any

surface for any period of time.

Always place the steam mop with the handle (8) supported in

the upright position when stationary and make sure the steam

mop is turned off when not in use.

Caution! Always empty the steam mop after use.

Note! Whenrstlledorafterrunningdry,itcantakeupto45

seconds for steam to be produced.

Smart select Technology (Fig. N)

ThissteammopisttedwithanSmartselectdial(2)which

shows various cleaning applications. They are used to select

the correct operating mode for your particular cleaning

operation.

Using Autoselect

, choose from one of the following

applications by turning the Smart select dial(2) until the

required setting is selected.

ENGLISH

Setting Mop Hand held

Wood/Laminate High temperature steam for

windows



Stone/Marble

 

Tiles/Vinyl Low temperature steam for

heavy grime

  

The steam mop will select the correct volume of steam

required for your particular cleaning operation.

Note: Always check you are using the correct setting before

using your steam mop.

Hints for optimum use

General

Caution:Neverusethesteammopwithoutrstattachinga

cleaning pad.

u Alwaysvacuumorsweeptheoorbeforeusingthesteam

mop.

u The easiest way to use the appliance is to tilt the handle

to a 45º angle and clean slowly, covering a small area at a

time.

u Use water only with no additives or chemicals with your

steam mop. To remove stubborn stains from vinyl or

linoleumoors,youcanpre-treatwithamilddetergent

and some water before using the steam mop.

Steam Cleaning with the mop

u Fit hand held steam cleaner (5) to the steam mop body

(11)

u Placeacleaningpad(13)ontheoorwiththevelcro'loop'

side facing up.

u Lightly press the steam mop down onto the cleaning pad

(13).

u Connect the steam mop to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Turn the Smart select dial(2) until the required setting is

reached. After a few seconds steam will start to come out

of the steam head.

Note!Whenrstlledorafterrunningdry,itcantakeupto45

seconds for steam to be produced.

u It takes a few seconds for steam to enter the cleaning pad.

The steam mop will now glide easily over the surface to be

sanitized/cleaned.

u Push and pull the steam mop slowly across the surface to

thoroughly steam clean each section.

u Whenyouhavenishedusingthesteammop,return

the handle (8) to the upright position, making sure that it

is supported and turn it 'OFF'. Wait until the steam mop

coolsdown(approximatelyveminutes).

Caution! It is important to monitor the water level in the

watertank.Torellthewatertankandcontinuetosanitize/

clean stand the mop upright making sure that the handle is

supported and turn the steam mop 'OFF'. Unplug the unit from

theelectricalwalloutlet,andrellthewatertank.

Caution! Never leave the steam mop in one spot on any

surface for any period of time. Always place the steam mop

with the handle (8) supported in the upright position when

stationary and make sure the steam mop is turned off when

not in use.

After use

u Turn the Smart select

dial(2) to the OFF position.

u Wait until the steam mop cools down.

u Unplug the steam mop from the electrical wall outlet.

u Empty the water tank.

u remove the cleaning pad (13) and wash it ready for next

use (take care to follow the wash care instructions printed

on the cleaning pad).

u Wrap the supply cable around the cable tidy hooks (7 and

9).

u There is a hanging bracket (15) built into the hand grip (6)

which allows your steam mop to be hung from a suitable

hook on the wall. Always ensure that your wall hook is

capable of supporting the weight of the steam mop safely.

Hand held steam cleaning

Warning! Unit will not produce steam unless it is connected to

themainbody(11)orthesteamhose(16)istted.

Warning! Only use in a horizontal position.

u Attach the required accessory.

u Connect the hand held steam cleaner to the mains.

u Press the ON/OFF button (1). It takes approximately 15

seconds for the steam mop to heat up.

u Turn the Smart select dial(2) until the required setting is

reached. After a few seconds steam will start to come out

of the steam head.

Note!Whenrstlledorafterrunningdry,itcantakeupto45

seconds for steam to be produced.

u Whenyouhavenishedusingthehandheldsteam

cleaner turn the Smart select dial(2) to the OFF position.

Turn the unit OFF by pressing the ON/OFF button (1) and

disconnect from the mains supply. Wait until the unit cools

downbeforestoring(approximatelyveminutes).

Accessories

The performance of your appliance depends on the accessory

used. BLACK+DECKER accessories are engineered to high

quality standards and designed to enhance the performance

of your appliance. By using these accessories you will get the

very best from your equipment.

ENGLISH

Troubleshooting

If your appliance seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local BLACK+DECKER repair agent.

Problem Step Possible solution

The steam mop is not

turning on

1. Check the unit is plugged in at the wall

socket.

2. Check the unit is switched on using the

ON/OFF switch (1)

3. Check the fuse in the plug.

The steam mop is not

producing steam

4. The steam mop will only produce steam if

the hand held steam cleaner (5) is

correctly docked into the main body (11)

orthesteamhoseisttedorthe

Autoselect

is turned to ON

5. Check that the water tank is full. Note:

Whenrstlledorafterrunningdryitcan

take up to 45 seconds for steam to be

produced.

6. Check steps 1, then 2, then 3

The steam mop stops

producing steam

during use

7. Check steps 4, then 5, then 3

The steam mop is

producing too much

steam during use

8. Turn the Smart select dial(2)

anti-clockwise to reduce the amount of

steam being produced

The steam mop is

producing too little

steam during use

9. Turn the Smart select dial(2) clockwise to

increase the amount of steam being

produced

No steam is being

produced from the

hand held steam

cleaner

10. Check that the Smart select dial(2) is at

the ON position

11. Check steps 5, then 1, then 2, then 3

The hand held steam

cleaner is producing

too little steam during

use

12. Turn the Smart select dial(2) clockwise to

increase the amount of steam being

produced

13. Check step 5

The hand held steam

cleaner is producing

too much steam during

use

14. Turn the Smart select dial(2)

anti-clockwise to reduce the amount of

steam being produced

The accessories keep

falling off the unit

15. Refer to the assembly chapter for correct

ttinginstructionsofallpartsand

accessories

Steam is escaping

from unexpected areas

of the unit

16. Refer to the assembly chapter for correct

ttinginstructionsofallpartsand

accessories

Where can I get further

information/

accessories

17. www.blackanddecker.co.uk/steammop

www.blackanddecker.ie/steammop

Service Information

BLACK+DECKER offers a full network of company-owned

and authorized service locations throughtout Asia. All

BLACK+DECKER Service Centers are staffed with trained

personneltoprovidecustomerswithefcientandreliable

product service.

Whether you need technical advice, repair, or genuine factory

replacement parts, contact the BLACK+DECKER location

nearest to you.

NOTE

u BLACK+DECKER’s policy is one of continuous improve-

ment to our products and, as such, we reserve the right to

changeproductspecicationswithoutpriornotice.

u Standard equipment and accessories may vary by country.

u Productspecicationsmaydifferbycountry.

u Complete product range may not be available in all

countries. Contact your local BLACK+DECKER dealers for

range availability.

简体中文

FSMH1321 蒸汽拖把

技术参数

FSMH1321

电压伏特

交流

220-240 伏特

功率瓦

1300

水箱容量毫升

500

重量千克

2.7

设计用途

BLACK+DECKER

FSMH1321 蒸汽拖把设计用于清

洁与清洗密封实木地板、密封复合地板、油地毡地

板、乙烯基地板、瓷砖地板、石地板及大理石地板。

本设备仅适用于室内家庭用途。

安全说明

警告！使用设备前，请仔

细阅读“安全、维护、保养”

手册的所有内容。使用设

备前，请仔细阅读本手册。

设备上的标签

设备上显示下列图形和日期码。

警示热蒸汽

倒置时滴水

蒸汽从四面逸出

不要让儿童在无人看

管下接触

只能手洗

部件名称

本设备包含如下部分或全部部件。

1. On/off 开关

2. Autoselect

旋钮

3. 手持式蒸汽设备手柄

4. 注水口盖子

5. 手持式蒸汽设备

6. 手柄

7. 顶端电源线整理钩

8. 主手柄

9. 底端电源线整理钩

10. 手持式蒸汽设备释放按钮

11. 主机身

12. 地板清洁头

13. 地板清洁垫

14. 地板清洁垫释放凸耳

15. 吊钩

16. 蒸汽软管

17. 蒸汽喷嘴

18. 蓝色角刷附件（用于难以去除的污渍）

19. 大型橡胶清洁器附件（用于淋浴屏/玻璃/镜子/

服装/内饰）

19a. 大型橡胶清洁器套

20. SteaMitt

21. SteaMitt

软管

22. SteaMitt

清洁垫

23. 可调节喷嘴

组装

警告！进行如下任何操作之前，请确保关

闭设备开关、拔下设备插头、设备处于冷

却状态并且不含水。

安装手柄（图 A）

u 将手柄 (8) 的底端向蒸汽拖把机身的顶端 (11)

滑动，直至其卡入到位。

连接手持蒸汽清洁器（图 B）

u 握住蒸汽拖把机身 (11) 背面，将手持蒸汽清洁器

(5) 紧紧推入蒸汽拖把机身 (11)，使它正确固定

在接口 (11a) 上方并卡入到位。

拆卸手持蒸汽清洁器（图 B）

u 按下主机身 (11) 上的释放按钮 (10)，同时将

手持蒸汽清洁器 (5) 提离接口 (11a) 并拉离主

机身 (11)。

安装清洁垫（图 C）

BLACK+DECKER

代理商提供备用清洁垫。

u 将清洁垫 (13) 置于地板上，魔术扣贴“环形”

面朝上。

u 将蒸汽拖把往清洁垫 (13) 上轻压。

警示！禁止让蒸汽拖把长时间停留在任一工作表

面上。蒸汽拖把处于静止状态时，切记使手柄 (8)

保持竖直位置；未使用蒸汽拖把时，请确保将其开

关关闭。

简体中文

拆卸软管和附件

警告！蒸汽软管 (16)、蒸汽喷嘴 (17) 和附件在使

用期间会发热。应等设备和所有附件冷却后才尝试

拆卸。

拆卸附件

u 顺时针旋转附件，然后拉离软管 (16)。

拆卸软管

u 按下蒸汽软管 (16) 上的蒸汽软管释放按钮 (16a)，

然后从手持式蒸汽设备上拉开。

SteaMitt

BLACK+DECKER

SteaMitt

设计用于消毒和清洁

瓷砖、工作台、厨房表面和浴室表面。本设备仅适

用于室内家庭用途。

将 SteaMitt

软管连接到手持式蒸汽设备

警告！每次使用前检查蒸汽喷嘴和软管上的密封件。

如果密封件丢失或损坏，请与最近的授权维修代理

联系。请勿使用设备。检查 SteaMitt

和软管上的

密封件。如果密封件丢失、受损或有任何蒸汽逸出，

请与最近的授权维修代理联系。请勿使用设备。确保

SteaMitt

软管或连接软管中没有堵塞。如果检测到

任何堵塞，请与最近的授权维修代理商联系。请勿

使用设备。

为 SteaMitt

安装清洁垫（图 H）

警告！确保蒸汽放气口没有任何堵塞。如果检测到

任何堵塞，请与最近的授权维修代理商联系。请勿

使用设备。

u 通过将清洁垫上方的“环形”魔术贴条 (22a)

粘贴到 SteaMitt

(4) 下方的“钩形”魔术贴垫

(20a)，将清洁垫 (22) 安装到 SteaMitt

(20) 上。

向下按紧。

警告！不应在没有安装清洁垫的情况下使用

SteaMitt

。

注：SteaMitt

可使用 4 种不同厚度的清洁垫。百洁

布（用于顽固污渍和非精致表面）、浴室垫（用于

水龙头和其他模压浴室表面）、标准垫（用于所有

较大的表面）和抛光垫（用于精致表面）。

警告！使用 SteaMitt

时务必将您的手放在

防护手套内（如图 M 所示）。

警告！切勿尝试在使用 SteaMitt

时

抓住其外部（如图 J 所示），这样会导致

烫伤。

警告！避免在狭窄的角落使用 SteaMitt

，

如图 K 所示。

警告！如果使用过程中出现问题，应使用

快速释放凸耳迅速从手中取出 SteaMitt

，

如图 P 所示。

拆卸清洁垫

小心！给蒸汽拖把更换清洁垫时，请务必穿上合适

的鞋子。

请勿穿拖鞋或露趾鞋。

u 将手柄 (8) 恢复到竖直位置，关闭蒸汽拖把电源

开关。

u 等待蒸汽拖把冷却（约 5 分钟）。

u 分开魔术贴，向上提起蒸汽拖把，从清洁垫上

取下。

警示！禁止让蒸汽拖把长时间停留在任一工作表

面上。

蒸汽拖把处于静止状态时，切记使手柄 (8) 保持竖直

位置；未使用蒸汽拖把时，请确保将其开关关闭。

给水箱加水（图 M）

注意！给水箱注入干净的自来水（不要使用任何添

加剂或化学品）。

注意！如果您所在地区的自来水水质较硬，建议您

使用去离子水。

u 向上翻开注水口盖子 (4)。

u 给水箱加水（不要使用任何添加剂或化学品）。

警告！装水时，请将水箱从主装置上拆下并保持水

平位置。

警告！本水箱的容量为 0.5 升。请勿超过水箱的最

高水位线。

u 关闭注水口盖子 (4)。

注意！确保注水口盖子已经稳固安装。

将软管和附件连接到手持式蒸汽清洁器

（图 F - K）

警告！每次使用前，检查手持式蒸汽清洁器 (5) 和

蒸汽软管 (16) 上的连接点之间的密封件。如果密封

件出现故障或损坏，请与最近的授权维修代理联系。

请勿使用设备。

安装软管

u 按下蒸汽软管 (16) 上的蒸汽软管释放按钮 (16a)。

u 将蒸汽软管 (16) 连接到手持式蒸汽清洁器 (5)，

并松开蒸汽软管释放按钮 (16a)，确保其卡入

到位。

重要信息！确保蒸汽软管 (16) 稳固连接到手持式蒸

汽清洁器 (5)。如果蒸汽从接头中逸出，则软管安装

不正确。关闭开关，让本设备冷却，然后拆下并重

新安装软管。

安装附件（图 G）

u 将蒸汽喷嘴 (17) 上的凸耳与附件的凹槽对齐。

u 将附件按压到蒸汽喷嘴 (17) 上，逆时针旋转，

直到附件卡入到位。

重要信息！所有附件，除了有自己的软管和接头

(21) 的 SteaMitt

(20) 外，均必须连接到蒸汽软管

(16) 方可使用。

简体中文

警告！不要在窗户等冷玻璃上使用 SteaMitt

，

因为温度突然变化可能会损坏玻璃。

警告！切勿将手套指向自己或指向任何其

他人。

注意：安装 SteaMitt

时，变速蒸汽旋钮会断开

连接，蒸汽流将受到限制。

使用

重要信息！若按照本手册中的说明操作并使用装

配的微纤维垫连续运行 90 秒以上，本设备将消灭

99.9% 的细菌。

开启和关闭

u 要启动设备，请按下 ON/Off 开关 (1)。蒸汽拖把

需要大约 15 秒钟进行加热。

u 要关闭设备，请按下 ON/Off 开关 (1)。

注意：在按下蒸汽按钮之前，务必将手放入

SteaMitt

。

警示！禁止让蒸汽拖把长时间停留在任一工作表

面上。

蒸汽拖把处于静止状态时，切记使手柄 (8) 保持竖直

位置；未使用蒸汽拖把时，请确保将其开关关闭。

警示！使用后，务必清空蒸汽拖把。

注意！刚注入水或水份耗尽后，可能需要最长 45

秒时间来产生蒸汽。

智能选择技术（图 N）

本蒸汽拖把装有智能选择旋钮 (2)，该旋钮提供各种

清洁用途指示。您可以根据清洁用途，设定正确的

操作模式。

使用自动选择

来选择以下应用之一，方法是旋转

智能选择旋钮 (2)，直到选定所需设置。

设置拖把手持式

实木地板/复合

地板

用于窗户的高温

蒸汽



石地板/大理石

地板

 

瓷砖地板/乙烯基

地板

用于重度污垢的低

温蒸汽

  

本蒸汽拖把会根据您的特殊清洁用途，选择合适的

蒸汽流量。

注意：使用蒸汽拖把之前，请务必确保您正在使用

正确的设置。

最佳使用提示

一般原则

警示：禁止在未安装清洁垫的情况下使用蒸汽拖把。

u 使用蒸汽拖把前，请务必使用吸尘器或扫把将地

板上的灰尘清除干净。

u 本产品最简单的使用方法就是将手柄倾斜至 45°

角，慢慢清洁，每次只清洁一小片地方。

u 只使用水，不要将蒸汽拖把与添加剂或化学品一

起使用。要清除乙烯基地板或油地毡地板上的顽

固污渍，可在使用蒸汽拖把前，用温和洗涤剂和

适量的水进行处理。

用拖把进行蒸汽清洁

u 将手持式蒸汽清洁器 (5) 安装到蒸汽拖把机身

(11) 上。

u 将清洁垫 (13) 置于地板上，魔术扣贴“环形”

面朝上。

u 将蒸汽拖把往清洁垫 (13) 上轻压。

u 将蒸汽拖把连接至主电源。

u 按下 ON/OFF 按钮 (1)。蒸汽拖把需要大约 15 秒

钟进行加热。

u 旋转智能选择旋钮 (2)，直至达到所需设置。

数秒后，蒸汽将从蒸汽头中涌出。

注意！刚注入水或水份耗尽后，最多可能需要 45

秒来产生蒸汽。

u 蒸汽需要几秒钟时间进入清洁垫。完成以上步

骤后，蒸汽拖把将能轻松在待清洁/清洗的表面

上滑动。

u 在表面上慢慢推拉蒸汽拖把，用蒸汽彻底清洁地

板的各个角落。

u 用完蒸汽拖把后，将手柄 (8) 返回到直立位置，

确保稳固支撑并将其关闭。等待蒸汽拖把冷却

（约 5 分钟）。

小心！务必监控水箱水位。要重新装满水箱并继续

清洁/清洗，请将拖把直立放置，确保手柄稳固支撑，

并关闭蒸汽拖把。从墙面插座上拔下工具插头，

然后重新注满水箱。

小心！禁止让蒸汽拖把长时间停留在任一工作表

面上。蒸汽拖把处于静止状态时，切记使手柄 (8)

保持竖直位置；未使用蒸汽拖把时，请确保将其开

关关闭。

使用后

u 将智能选择旋钮 (2) 转至关闭位置。

u 等待蒸汽拖把冷却。

u 从墙面插座上拔下蒸汽拖把插头。

u 清空水箱。

u 拆卸清洁垫 (13) 并清洗以备下次使用（注意遵

循清洁垫上印制的清洁保养说明）

简体中文

u 将电源线缠绕在电源线整理钩上（7 和 9）。

u 可以使用手柄 (6) 内置的吊钩 (15) 将蒸汽拖把挂

到墙上一个符合其重量标准的挂钩上。请务必确

保所使用的挂钩能够安全地承受蒸汽拖把的重量。

手持式蒸汽清洁

警告！在连接至主机身 (11) 或安装蒸汽软管 (16) 前，

设备不会产生蒸汽。

警告！只能在水平位置使用。

u 连接所需的附件。

u 将手持式蒸汽清洁器连接到电源。

u 按下 ON/OFF 按钮 (1)。蒸汽拖把需要大约 15

秒钟进行加热。

u 旋转智能选择旋钮 (2)，直至达到所需设置。

数秒后，蒸汽将从蒸汽头中涌出。

注意！首次注水或运行干燥后，可能需要最长 45

秒时间来产生蒸汽。

u 使用手持式蒸汽清洁器后，将智能选择旋钮 (2)

旋转到关闭位置。按 ON/OFF 按钮 (1) 关闭设备

并断开电源。等待设备冷却再存放（约 5 分钟）。

附件

设备的性能取决于所使用的附件。BLACK+DECKER

附件依据高质量标准进行规划，并设计用于增强设

备的性能。使用这些配件会令您的设备如虎添翼。

故障排除

如果设备似乎无法正常运行，请按照以下说明进

行操作。如果仍不能解决问题，请联系您当地的

BLACK+DECKER 维修代理。

问题步骤可能的解决方案

蒸汽拖把没有启动

检查设备是否已插入墙壁插座。

2. 使用 ON/OFF 开关 (1) 检查设备是

否已打开

检查插头中的保险丝。

蒸汽拖把不产生

蒸汽

4. 只有当手持式蒸汽清洁器 (5) 正确

插入主机

(11)，或安装了蒸汽软管，

或已将

Autoselect

旋钮旋转到开

启位置，蒸汽拖把才会产生蒸汽

检查水箱是否已满。注：刚注入水

或水份耗尽后，可能需要最长

45 秒

时间来产生蒸汽。

6. 依次检查步骤 1、步骤 2 和步骤 3

蒸汽拖把在使用过程

中停止产生蒸汽

7. 依次检查步骤 4、步骤 5 和步骤 3

蒸汽拖把在使用过程

中产生的蒸汽太多

8. 逆时针旋转智能选择旋钮 (2)，以减

少产生的蒸汽量

蒸汽拖把在使用过程

中产生的蒸汽太少

9. 顺时针旋转智能选择旋钮 (2)，以增

加产生的蒸汽量

手持式蒸汽清洁器不

产生蒸汽

10. 确认智能选择旋钮 (2) 位于 ON 位置

11. 依次检查步骤 5、步骤 1、步骤 2

和步骤

问题步骤可能的解决方案

手持式蒸汽清洁器在

使用过程中产生的蒸

汽太少

12. 顺时针旋转智能选择旋钮 (2)，以增

加产生的蒸汽量

13. 检查步骤 5

手持式蒸汽清洁器在

使用过程中产生的蒸

汽太多

14. 逆时针旋转智能选择旋钮 (2)，以减

少产生的蒸汽量

附件一直从设备上

掉落

15.

有关所有部件和附件的正确安装说

明，请参阅组装章节

蒸汽从设备的意外区

域逸出

16.

有关所有部件和附件的正确安装

说明，请参阅组装章节

在哪里可以获得更多

信息/附件

17. www.blackanddecker.co.uk/steammop

www.blackanddecker.ie/steammop

服务信息

BLACK+DECKER 提供亚洲地区覆盖范围广泛的公

司隶属和授权服务地点。所有的 BLACK+DECKER

服务中心都具有训练有素的人员，为客户提供高效

和可靠的产品服务。

不论您是需要技术建议、维修或原厂替换部件，

请联系最靠近您的 BLACK+DECKER 地点。

备注

u BLACK+DECKER 的政策是持续改进我们的产品，

因此，我们保留随时更改产品规格的权利，恕不

另行通知。

u 标准设备和附件可能会因国家（地区）而异。

u 不同国家（地区）的产品规格也可能会有所不同。

u 并非所有的国家（地区）都可提供完整的产品

系列。有关各产品系列的供货情况，请联系您当

地的 BLACK+DECKER 代理商。

制造商：百得美国公司

地址： 701 E Joppa Rd, TW050 MD21286，

Towson, 美国

产地：江苏南通

N601314

05/2018

BLACK+DECKER FSMH1321 ユーザーマニュアル

ブランド: BLACK+DECKER

モデル: FSMH1321

タイプ: ユーザーマニュアル

PDFをダウンロードします

報告

他の言語で

English: BLACK+DECKER FSMH1321 User manual

BLACK+DECKER FSMH1321 ユーザーマニュアル

BLACK+DECKER FSMH1321 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント