Chinavision CVAIC-OG72 ユーザーマニュアル

User Manual

1

Introduction

Thanks for purchasing this hunting camera which is

an professional product for recording and

observing the wildlife.

We provide detail user manual for your reference.

Please read this manual carefully before first use.

We are serious and strict when writhing the manual.

While the errors and omissions may exist during

printing process. Please understand.

We have no responsibility for the data damage

which are caused by faulty operation,incompetent

repairment or other accidents.

There is no notice if the information of this user

manual changed.

2

This document is subject to copyright protection.

Any other copy without prior written permission of

our company is not allowed.

Our company reserve all the right for the final

interpretation of this user manual,three guarantees

and relative documents.

Safety

Please read below safety precautions carefully

before using the camera.

· Do not try to disassemble the product case.Only

authorized technician can repair the product.

· The camera will be hot after using for too long

time.This is normal.

· Please use the accessory provided by our factory.

3

Parts Of The Camera

1. Up/Video Button

2. Right Button

3. Shot Button

4. OK Button

5. Left Button

6. Menu Button

7. Replay Button

8. Down/Capture Button

9. Micro SD Card Slot

10. AV Jack

11. USB Jack

12. OFF

13. Test

15

4

14. ON

15. Display Screen

16. Infrared LEDs

17. Lens

18. Motion Sensor

Power Supply

Please install batteries before using the camera.

♦

Open the camera case and remove the battery

cover. Install 8 pieces of 1.5V AA batteries. Please

make sure the electrode is correct.

16

17

18

5

♦

If the camera is in low power, please connect the

camera to a power adapter(not provide) for power

supply.

Inserting The Memory Card

The camera has no built-in memory. Please prepare

a Micro SD card and insert it into the camera for

saving files. Before recording, please format the

memory card first.

♦

Support Micro SD card,up to 32GB. Suggest to

use class 6 or above high speed card.

♦

To avoid malfunction, the memory card should

be far away water, strong vibration,dust, hot source

and direct sunlight.

6

♦

Do not insert the memory card forcibly. Please

refer to the marking on the camera.

♦

For the first time use, please wait for the memory

card temperature reach the ambient

temperature.The camera will be short-circuit

influenced by environment temperature and

humidity. Please notice protection for the camera

when using it outdoor.

♦

If the capacity of memory card is full,the camera

will stop recording automatically and the LEDs will

go out.

♦

Press the edge of the card gently to pop-up the

TF card.

7

Basic Operation

Turn On And Off The Camera

Switch the Mode Button to“Test/On”to turn on

the camera.

Switch the Mode Button to “Off” to turn off the

camera.

System Setup

Switch Mode Button to“Test”, then you can set

the system parameters.

1. Press Video/Capture button to switch between

these two modes.

2. Press Menu button to open the setup menu.

8

3. Press Up/Down button to scan all menu. Then

press OK button to enter the options interface.

4. Press Up/Down button to scan all options. And

press OK button to confirm options.

5. Press Menu button again to turn back to last

menu or exit the setup menu.

Setup menu and function as below:

Mode

Set the working mode. In capture mode,the

camera just take pictures. In Video mode,the

camera just record video. In capture&video

mode,the camera will take a photo first,then start

to record video.

Options：【Photo】/【Video】/【Photo&Video】.

9

Photo Resolution

Set the still image resolution.The bigger the

resolution is ,the higher the sharpness is. It will take

bigger space either.

Options：【12MP(4000x3000P)】/

【8MP(3264x2448P)】/【5MP(2592x1944P)】/

【3MP(2048x1536P)】/【1MP(1280x960P)】.

Photo Series

Set the photo number of continuous shooting. In

photo mode, the camera will take photos

continuously.

Options：【1 photo】/【2 photos in series】/【3 photos

in series】.

10

Video Resolution

Set the video resolution. The bigger the resolution

is ,the longer the video time can be stored.

Options：【1920x1080P】/【1280x720P】/【720x480P】

/【640x480P】/【320x240P】.

TL Video Resolution

Set the resolution of time lapse video .

Options:【2592x1944P】/【2048x1536P】.

Video Length

Set the duration of recording a video clip.

The shortest time is 3 seconds and the longest

time is 10 minutes.

Options：3 seconds~10 minutes.

11

Audio Recording

Open this function,the camera will record audio

when recording video.

Options：【On】/【Off】.

Shot Lag

Set the time of delay shooting when the camera

detects the motion. Within the selected time, the

camera will not record any image or video. It can

avoid to store too much same event and save more

capacity.

Options：5 seconds~60 minutes.

IR Distance

Set the distance of infrared induction.

Options：【Near】/【Middle】/【Far】.

12

Sensitivity Motion Sensors

Set the sensitivity of the sensor. Environmental

impact is small indoors, you can choose “Low”. In

outdoor, choose “Middle”in normal condition.

Choose “High”if the environment impact is huge

outdoors. The temperature can also influence the

sensor sensitivity. “High Sensitivity”applies to

mild environment. ”Low Sensitivity ”applies to

cold environment.

Options：【Low】/【Middle】/【High】.

Target Recording Time

Set the target recording time. As shown in below

picture, you can set the start and stop time. The

13

camera will work just in the stated time slot. In

other time, the camera will keep in standby state.

Options：【On】/【Off】.

Time Lapse

In Time lapse menu, there are three options as

below.

Set

Target recording time

Start： Stop：

Hr：Min Hr：Min

00 00 00 00

MENU Back OK Select

14

[Normal]: The camera will take pictures

automatically as per set time interval. For

example,set the interval time to 1 hour, the camera

will take a photo each hour. If you want to observe

that a plant blooms, the camera will take 24 photos

in 24 hours to record the whole process of

blooming.

[TL Video]: You can set the interval time.The time

range is from 1 second to 24 hours. For example,

set the interval to 1 hour, the camera will take a

photo each hour. If the camera works for 24

15

hours,there will be 24 photos. These photos will be

converted into a video.

[Off]: Close the time lapse function.

Language

Set the language display on screen.

Options：【English】/【German】/【Danish】/【Finnish】

Settings

Set time lapse

Hr：Min ：Sec

00 00 30

Notification:Motion

sensors deactivated

MENU Back OK Select

16

/【Swedish】【Spanish】/【French】/【Italian】/【Dutch】

/【Portuguese】/【Simplified Chinese】/【Japanese】.

Time & DateSet the date and time of camera.

The date format: dd/mm/yyyy, yyyy/mm/dd，

mm/dd/yyyy.

The time format: 24h，12h.

Press Left/Right button to choose the item.Press

Up/Down button to adjust the value. And press OK

button to confirm.

Options：【Set time&date】/【Time format】/【Date

format】.

Photo Stamp

Stamp the date&time on the photos or not.

Options：【Time&date】/【Date】/【Off】.

17

Password Protection

Set the power-on password of the camera. The

password is four digits，each digit ranges from 0 to

9.

If you forget the password, please reset the camera.

Then all parameters will reset to the factory

settings.

Options：【On】/【Off】.

Beep Sound

Open/close the button sound.

Options：【On】/【Off】.

Format Memory Card

Formatting the memory card will delete all data

permanently. Before using a new memory card or a

18

card that has been used in another device

previously ,please format the memory card.

Options：【Yes】/【No】.

Serial NO.

Set the unique serial number for the camera. The

number is four digits，each digit ranges from 0 to 9.

Options：【On】/【Off】.

Reset Settings

Restore the camera to factory default settings including

password,serial number and so on.

Options：【On】/【Off】.

Version

Look up the Firmware information of the camera.

19

Take Photos ,Record Video ,Playback

Switch the Mode Button to “Test”. In this

mode,you can take photos, record video and

playback files manually.

♦

Take Photos：Press Capture button to switch to

photo mode. Press Shot button to take a picture.

♦

Record Video：Press Video button to switch to

video mode.Press Shot button to start to record a

video clip. Press Shot button again to stop

recording.

♦

Playback：Press Playback button to enter the

playback interface. Press Up/Down button to scan

photos or video. When playback video, press OK

button to play the video. Press OK button again to

ページが読み込まれています...

Chinavision CVAIC-OG72 ユーザーマニュアル

Chinavision CVAIC-OG72 ユーザーマニュアル

他の言語で

その他のドキュメント