HT-CT390 4-586-112-51(1)
Startup Guide
入門指南
Sound Bar
HT-CT390
Bar Speaker
條形揚聲器
Subwoofer
超低音揚聲器
Supplied accessories
附件
Remote control (1)
遙控器（1）
R03 (size AAA) batteries (2)
R03（AAA型）電池（2）
Optical digital cable (1)
光纖數位線（1）
Wall mounting brackets (2)
and screws (2)
牆壁安裝支架（2）和
螺絲（2）
Speaker pads for the subwoofer (4)
Refer to the supplied Operating Instructions on installing the subwoofer
horizontally.
用於超低音揚聲器的揚聲器襯墊（4）
有關水平安裝超低音揚聲器，請參閱附帶的使用說明書。
To mount the Bar Speaker on a wall
Refer to the supplied Operating Instructions.
將條形揚聲器安裝在牆上
請參閱附帶的使用說明書。
4
Turning on the system
開啓系統
Connect the AC power cords (mains leads).
Press
(power).
The top panel display lights up.
When the power indicator of the subwoofer turns green, wireless connection of Bar
Speaker and subwoofer is completed. If it does not turn on, the wireless transmission is
not activated. Refer to “No sound is heard from the subwoofer.” of “Troubleshooting” in
the supplied Operating Instructions.
連接交流電源線。
按
（電源）。
頂顯示面板亮起。
當超低音揚聲器的電源指示器轉爲綠色時，條形揚聲器和超低音揚聲器的無線連接完成。如果
系統未開啓，則無線傳送不啟動。請參閱附帶的使用說明書內“故障排除”中的“從超低音揚
聲器中聽不到聲音。”。
5
Listening to the sound
聆聽聲音
INPUT
+/–
SW
+/–
Press INPUT repeatedly until the device you want appears in the top panel display.
Then, press
+/– repeatedly to adjust the volume of the system and press
SW
+/– repeatedly to adjust the volume of the subwoofer.
重複按 INPUT 直至您要的裝置出現在頂顯示面板。然後，重複按
+/- 以調節系統
的音量，重複按 SW
+/- 以調節超低音揚聲器的音量。
Setup completed! Enjoy!
Please refer to the supplied Operating Instructions about the sound
mode, and other functions.
Operating Instructions
使用說明書
設定完成！享受吧！
有關聲音模式及其它功能，請參閱附帶的使用說明書。
© 2016 Sony Corporation Printed in Malaysia
1
Connecting with a TV
與電視機連接
Is the HDMI input jack on your TV labeled “ARC” ?
您的電視機上的 HDMI 輸入插孔標註了“ARC”嗎？
NO/否
Optical digital cable (supplied)
光纖數位線（附帶）
High Speed
HDMI cable (not
supplied)
High Speed HDMI
cable（無附帶）
YES/是
High Speed HDMI cable (not supplied)
High Speed HDMI cable（無附帶）
Note
Make sure that the HDMI cable is firmly inserted.
註
請確保 HDMI 連接線已牢固插入。
2
Setting up the remote control
設定遙控器
3
Turning on the TV
開啓電視機
Power
電源
Input
輸入
Change the input of the TV to the input which the Bar Speaker is connected.
將電視機的輸入更改至條形揚聲器連接的輸入。
GB
CT
4-586-112-51(1)
Listening to music from a BLUETOOTH device
聆聽來自藍牙裝置的音樂
When pairing a BLUETOOTH device
配對藍牙裝置時
INPUT
Blue LED indicator/藍色 LED 指示器
PAIRING
BLUETOOTH device
藍牙裝置
To pair the system with a BLUETOOTH device (Pairing)
Place the BLUETOOTH device within 1 meter from the Bar Speaker.
Press PAIRING on the Bar Speaker.
The blue LED indicator on the Bar Speaker flashes quickly ( ) during BLUETOOTH pairing.
Turn on the BLUETOOTH function, and then select “HT-CT390” after searching for it
on the BLUETOOTH device.
Perform this step within 5 minutes, otherwise pairing mode may be canceled. When the
BLUETOOTH connection is established, the blue LED indicator lights up ( ).
If passkey is required on the BLUETOOTH device, enter “0000”.
To listen to music from the paired device
Turn the BLUETOOTH function of the paired device to on.
Press INPUT repeatedly to select “BT”.
The system automatically reconnects to the BLUETOOTH device it was most recently
connected to. When the BLUETOOTH connection is established, the blue LED indicator lights
up ( ).
Start playback on the BLUETOOTH device.
Adjust the volume.
將系統與藍牙裝置配對時（配對）
將藍牙裝置放在離條形揚聲器 1 米内之處。
按條形揚聲器上的 PAIRING。
藍牙配對時條形揚聲器上的藍色 LED 指示器快速閃爍（ ）。
開 啓 藍牙功能，然後在藍牙裝置上搜尋“HT-CT390”，搜到後再進行選擇。
在 5 分鐘内進行此步驟，否則配對模式可能會被取消。當藍牙連接建立時，藍色 LED 指示器亮起
（ ）。如果藍牙裝置需要密碼，輸入“0000”。
聆聽來自配對裝置的音樂
開啓配對裝置的藍牙功能。
重複按 INPUT 以選擇“BT”。
系統自動與最近連接的藍牙裝置重新連接。當藍牙連接建立時，藍色 LED 指示器亮起（ ）。
開始在藍牙裝置上播放。
調節音量。
When using One-touch connection (NFC)
使用一觸式連接（NFC）時
Blue LED indicator/藍色 LED 指示器
Hold the remote device near to the N-Mark on the Bar Speaker until the remote
device vibrates.
When the BLUETOOTH connection is established, the blue LED indicator on the Bar Speaker
lights up ( ).
Start playback of audio source on the remote device.
• Compatible remote devices
Remote devices with a built-in NFC function
(OS: Android™ 2.3.3 or later, excluding Android 3.x)
將遠程裝置握近條形揚聲器上的 N-標記直至遠程裝置振動。
當藍牙連接建立時，條形揚聲器上的藍色 LED 指示器亮起（ ）。
開始播放遠程裝置上的音源。
• 兼容的遠程裝置
備有內置 NFC 功能的遠程裝置
（操作系統：Android
TM
2.3.3 或更新，Android 3.x 除外）
SongPal
A dedicated App for this model is available on both Google Play™ and
App Store.
Search for “SongPal” and download the free App to find out more about the convenient
features.
可從 Google Play
TM
和 App Store 獲取此型號的專用應用程序。
搜索“SongPal”並下載免費的應用程序以獲知更多有關方便的功能。
-
1
