Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
MUZ5FW1
絞肉器
[zf] 使用說明書
[en] Instruction manual
絞肉器 6
Meat mincer 8
6
zf
為了您的安全起見
為了您的安全起見
這些配件適用於萬用廚師機 MUM5... 。
請遵照食物調理機 MUM5… 的操作說明。
本電器適用於絞碎生的或烹煮過的肉、鹹豬肉、禽肉和魚肉。不可用於處
理其他物體或物質。其他應用僅限使用製造商許可的配件。
使用本電器的安全說明
A 受傷的風險
不可將手伸入送入管中，請務必使用推料器加入食材。傳動器未靜止之
前，不可裝上/卸下絞肉器。
A 重要！
僅限在指定操作位置使用絞肉器。使用前必須完全組裝好絞肉器。切勿
將絞肉器附件組合在底座上。
總覽
請摺起圖解說明頁。
圖
A：
1 絞肉器配件
a 螺紋環
b 多孔盤(孔直徑 4.5 mm)
c 刀片
d 蝸輪與傳動裝置
e 鎖桿
f 封蓋
2 裝填盤
3 推料器
選用配件
4 果漿配件
5 餅乾成型器
6 研磨器
7 3/6mm絞肉盤
(孔直徑 3 mm 和 6 mm)
圖 B： 操作位置
過載保護
為了避免絞肉器過載導致嚴重損壞本電器，傳
動裝置有凹痕（預定的中斷點）。如果過載，傳動
裝置會中斷。更換傳動裝置的方法很簡單。客
服中心有提供新的傳動裝置
■ 鬆開蝸輪上的固定螺絲。
■ 更換傳動裝置。
■ 鎖緊固定螺絲。
操作本電器
第一次使用前，請參閱「清潔和維護」徹底清潔
絞肉器。
重要資訊
在這些使用建議的操作速度參考值的說明中，
參考的是附有 7 種設定的旋轉開關的電器。
關於附有 4 種設定的旋轉開關的電器，您可
以在 7 種設定的旋轉開關的值之後的括號中
找到值。
■ 依指示的順序組合絞肉器附件（圖 A）。不
可完全鎖緊螺紋環。
■ 插入封蓋。注意位置（圖 C）！
圖 D：
■ 按下釋放鈕，然後將旋轉臂轉到
位置 4。
■ 連接絞肉器和傳動裝置。
注意與傳動器相關的傳動裝置 (1d) 的位
置。視需要稍微轉動傳動裝置。若要這樣
做，不可用螺絲鎖緊螺紋環！
■ 朝逆時鐘方向轉動絞肉器。
■ 壓下鎖定桿。
■ 立刻鎖緊螺紋環。
■ 裝上裝填盤。
■ 將碗或碟子放在出口下。
■ 插入主電源插頭。
■ 將旋轉鈕設定為 7 (4) 設定。
■ 將要處理的食物放在裝填盤中。
■ 使用推料器將食材推入。
7
zf
清潔和保養
W 警告！
不可處理骨頭。
要訣：用絞肉器處理韃靼牛排兩次。
使用本電器後
■ 使用旋轉開關關閉本電器的電源。
■ 抬高鎖桿。
■ 朝順時針方向旋轉絞肉器，然後將其取下。
■ 清潔絞肉器。
清潔和保養
注意！
不可使用具研磨性的清潔劑。表面可能損壞。
不可用洗碗機清洗絞肉器和個別零件。
■ 鬆開螺紋環並拆解附件。
■ 用手和清水沖洗個別零件並立刻晾乾。
選用配件
（可從經銷商取得）
W 警告！
組合配件時切勿包含刀片和絞肉盤。請遵照上
述有關「為了您的安全起見」、「使用後」或「清
潔和保養」的所有指示。
果漿配件
壓下例如莓果、蕃茄、蘋果、梨子、薔薇果（壓下
前請烹煮薔薇果 1 小時）等水果取出的果肉
特別適合做果醬。
圖 E：
■ 依本說明書的描述準備絞肉器配件。注意
組合果漿配件時所需要的個別零件和順
序。
■ 首先盡可能鬆開固定螺絲，直到果肉流出
時仍是濕的為止。
■ 然後調整固定螺絲，直到果肉以所需的含
水率流出外止。
■ 將要處理的食物放在裝填盤中。使用推料
器將食材推入。
■ 將旋轉鈕設定為 7 (4) 設定。
餅乾成型器
塑造餅乾麵團或餅皮的形狀。
圖 F：
■ 依本說明書的描述準備絞肉器配件。注意
組合餅乾配件時所需要的個別零件和順
序。
■ 將要處理的麵團放在裝填盤中。使用推料
器將食材推入。
■ 視麵團穩定性而定，將旋轉開關轉到設定
4 (2) 或 5 (3)。
■ 用餅皮切刀切開流出本電器的有造型的
麵團。如果麵團流出太快，短暫關閉食物處
理機電源。
研磨器
用於研磨杏仁、堅果和乾麵包或麵包捲。
W 警告！
僅限處理少量的乾果和杏仁果！
圖 G：
■ 依本說明書的描述準備絞肉器配件。注意
組合研磨器配件時所需要的個別零件和
順序。
■ 將要處理的食物放在裝填盤中。使用推料
器將食材推入。
■ 視食物硬度而定，將旋轉開關轉到設定
3(2) 或 4 (3)。
保留資料隨時更改的權利。
8
en
For your safety
The accessories are suitable for the food processor MUM5.... .
Follow the operating instructions for the food processor MUM5.... .
This appliance is suitable for mincing and mixing raw or cooked
meat, bacon, poultry and sh. It must not be used for processing
other objects or substances. Other applications are possible if the
accessories approved by the manufacturer are used.
Safety instructions for this appliance
A Risk of injury
Do not reach into the feed tube, always use the pusher to add more
ingredients. Do not attach / remove the mincer until the drive is at a
standstill.
A Important!
Use the mincer in the specied operating position only. The mincer
must be completely assembled before use. Never assemble the
mincer attachment on the base unit.
Overview
Figure A:
1 Mincer attachment
a Threaded ring
b Perforated disc
(hole diameter 4.5 mm)
c Blade
d Worm gear with driver
e Locking lever
f Seal
2 Filler tray
3 Pusher
Optional accessories
4 Fruit press attachment
5 Viennese whirl attachment
6 Grater attachment
7 Perforated disc
(hole diameter 3 mm and 6 mm)
Figure B: Operating position
Protection from overload
To prevent serious damage to your appli-
ance if the mincer is overloaded, the driver
has a notch (predetermined breaking point).
If an overload occurs, the driver breaks
instead. However, the driver can easily be
replaced. A new driver is available from
customer service.
■ Unscrew fastening screw on the worm
gear.
■ Replace driver.
■ Tighten fastening screw.
Operating the appliance
Thoroughly clean the mincer before using
for the first time, see “Cleaning and care”.
Important information
In these instructions for use the recom-
mended reference values for the operating
speed refer to appliances with a 7-setting
rotary switch. For appliances with a
4-setting rotary switch you can find the
values in brackets after the values for a
7-setting rotary switch.
9
en
■ Assemble mincer attachment in the
indicated sequence (Fig. A). Do not
fully tighten threaded ring.
■ Insert seal. Note position (Fig. C)!
Figure D:
■ Press the Release button and
move the swivel arm to
position 4.
■ Connect mincer to the drive.
Note position of the driver (1d) with
respect to the drive. If required,
turn the driver slightly. To do this, the
threaded ring must not be screwed
tightly!
■ Turn mincer anti-clockwise.
■ Press down locking lever.
■ Now tighten the threaded ring.
■ Attach filler tray.
■ Place a bowl or plate under the outlet
opening.
■ Insert the mains plug.
■ Set rotary knob to setting 7 (4).
■ Place the food to be processed in the
filling tray.
■ Use the pusher to push in ingredients.
W Warning!
Do not process bones.
Tip: Process steak tartare through the
mincer twice.
After using the appliance
■ Switch off the appliance with the rotary
switch.
■ Lift up locking lever.
■ Rotate the mincer in a clockwise direc-
tion and remove.
■ Clean mincer.
Cleaning and servicing
Attention!
Do not use abrasive cleaning agents.
Surfaces may be damaged.
Mincer and individual parts are not
dishwasher-proof.
■ Loosen threaded ring and disassemble
attachment.
■ Rinse individual parts by hand and dry
immediately.
Optional accessories
(available from dealers)
W Warning!
Always assemble the accessories without
blades and perforated discs. Follow all
instructions mentioned above concerning
“For your safety”, “After work” or “Cleaning
and Servicing”.
Fruit press attachment
For pressing e.g. berries, tomatoes, apples,
pears, rosehips (cook rosehips for 1 hour
before pressing). Extracted fruit pulp is
especially suitable for making jam.
Figure E:
■ Preparation as described for mincer
attachment. Note required individual
parts and sequence when assembling
the fruit press attachment.
■ First undo the fastening screw as far as
is required to allow the pulp to flow out
while still moist.
■ Then adjust the fastening screw until
the pulp flows out with the required
moisture.
■ Place the food to be processed in the
filling tray. Use the pusher to push in
ingredients.
■ Set rotary knob to setting 7 (4).
Viennese whirl attachment
for shaping biscuit dough or short pastry.
Figure F:
■ Preparation as described for mincer
attachment. Note required individual
parts and sequence when assembling
the biscuit attachment.
■ Place the dough to be processed in the
filling tray. Use the pusher to push in
ingredients.
■ Turn rotary switch to setting 4 (2) or
5 (3) depending on dough consistency.
■ Separate the shaped dough coming out
of the appliance with a pastry cutter.
Briefly switch off the food processor if
the dough comes out too quickly.
10
en
Grater attachment
for grating almonds, nuts and dried bread or
bread rolls.
W Warning!
Process only dry nuts and almonds in small
quantities!
Figure G:
■ Preparation as described for mincer
attachment. Note required individual
parts and sequence when assembling
the grating attachment.
■ Place the food to be processed in the
filling tray. Use the pusher to push in
ingredients.
■ Turn rotary switch to setting 3 (2)
or 4 (3) depending on hardness of
the food.
Subject to alterations.
6
博西家用電器股份有限公司
台北市內湖區洲子街80 號11 樓
客服專線: 0800-368-888
www.bosch-home.com.tw
請立即至MyBosch註冊您的產品並享有專屬福利:
• 產品使用提示與小祕訣
• 保固延長方案
• 產品規格與使用手冊
• 售後服務相關資訊
立即免費註冊:
https://www.bosch-home.com.tw/mybosch
感謝您購買博世家用電器產品
8001132603
*8001132603*
(980925)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
