DWD112E
3
9
English
中文
Copyright DEWALT
a
c
b
a
b
Figure 1
Figure 2
1
c
d
e
f
2
Figure 4
Figure 3
Figure 5
g
h
E NGLI SH
3
VARIABLE SPEED REVERSIBLE DRILL
DWD112E
Congratulations!
You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make D
EWALT one of the most reliable
partners for professional power tool users.
Technical data
DWD112E
Voltage V 220
Power input W 701
No load speed min
-1
0-2,500
Maximum drilling range
steel/wood mm 13/25
Torque Nm 10.9
Chuck spindle
thread size UNF 1/2"x20
Maximum chuck
capacity mm 13
Weight kg 1.9
L
pA
(sound pressure) dB(A) 83
K
pA
(sound pressure
uncertainty) dB(A) 3
L
WA
(acoustic power) dB(A) 94
K
WA
(acoustic power
uncertainty) dB(A) 3
Vibr
ation total values (triax vector sum) determined
according to EN 60745:
Vibration emission value ah
Screwdriving without Impact
a
hD
= m/s² 13 13 13
Uncertainty K = m/s² 1.5 1.5 1.5
The vibration emission level given in this information
sheet has been measured in accordance with a
standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
WARNING: The declared vibration
emission level represents the main
applications of the tool. However if the
tool is used for different applications,
with different accessories or poorly
maintained, the vibration emission may
differ. This may significantly increase the
exposure level over the total working
period.
An estimation of the level of exposure to
vibration should also take into account
the times when the tool is switched off
or when it is running but not actually
doing the job. This may significantly
reduce the exposure level over the total
working period.
Identify additional safety measures to
protect the operator from the effects of
vibration such as: maintain the tool and
the accessories, keep the hands warm,
organisation of work patterns.
Fuses:
China 220 V tools 10 Amperes, mains
Definitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury .
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury .
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury .
CAUTION: Used without the safety alert
symbol indicates a potentially hazardous
situation which, if not avoided, may
result in property damage .
Denotes risk of electric shock.
Denotes risk of fire.
E NGLISH
4
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and instructions Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduc
e
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
E NGLISH
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaire
d
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that
the
safety of the power tool is maintained.
Additional Specific Safety Rules
for Drills
ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handles supplied with the
tool. Loss of control can cause personal
injury.
powe
r tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own
cord. Cutting accessory contacting a “live”
wire may make exposed metal parts of the
power tool “live” and shock the operator.
clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control.
safety goggles or other eye
protection. Drilling operations cause chips to
fly. Flying particles can cause permanent eye
damage.
and tools get hot during operation.
Wear gloves when touching them.
handles dry, clean, free from oil and
grease. it is recommended to use rubber
gloves. This will enable better control of the
tool.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
– Impairment of hearing
– Risk of personal injury due flying particles.
– Risk of burns due to accessories becoming hot
during operation.
– Risk of personal injury due to prolonged use.
•
•
•
•
Wear
Hold
Use
Wear
Bits
Keep
Markings on tool
The following pictograms are shown on the tool:
Read instruction manual
before use.
DATE CODE POSITION
Date Code, which also includes the year of
manufacture, is printed into the housing surface.
Example:
2008 XX XX
Year of Manufacture
•
•
•
5
E NGLISH
6
Package Contents
The package contains:
1 Drill
1 Chuck key (DWD112E)
1 Instruction manual
for damage to the tool, parts or
accessories which may have occurred during
transport.
the time to thoroughly read and
understand this manual prior to operation.
Description (fig. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. Variable speed trigger switch
b. Lock-on button
c. Forward/reverse button
d. Chuck
e. Cord protector
f. Cord set
INTENDED USE
These heavy-duty V.S.R. drills are designed for
professional drilling.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These heavy-duty drills are professional power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operator
s use this tool.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT power tool is double
insulated in accordance with EN 60745;
therefore no earth wire is required.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
EWALT service organization.
• Check
• Take
WARNING: NEVER use a light socket.
NEVER connect the live (L) or
neutral (N) wires to the earth
pin marked E or
.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
Also refer to the table below.
Conductor size (mm
2
) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
220-240
0 – 2.0 6 6 6 6 6 6
2.1 – 3.4 6 6 6 6 6 6
3.5 – 5.0 6 6 6 6 10 15
5.1 – 7.0 10 10 10 10 15 15
7.1 – 12.0 15 15 15 15 20 20
12.1 – 20.0 20 20 20 20 25 –
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
E NGLISH
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
Switches (fig. 1, 2)
To start the drill, depress the trigger switch; to stop
the drill, release the trigger.
A variable speed trigger switch (a) permits speed
control—the farther the trigger is depressed, the
higher the speed of the drill.
For continuous operation, press and hold the
variable speed switch, move the lock-on button (b)
up, then release the switch.
NOTE: Use lower speeds for starting holes without
a center punch, drilling in metal or plastics, driving
screws or drilling ceramics. Higher speeds are better
for drilling wood and composition boards and using
abrasive and polishing accessories.
The forward/reverse lever (c) is used for withdrawing
bits from tight holes and removing screws. It is
located above the trigger switch. To reverse the
motor, rel
ease the trigger switch FIRST and then
push the lever to the right. After any reversing
operations, return lever to forward position.
To stop continuous operation, press the switch
briefly and release it. Always switch the tool off when
work is finished and before unplugging.
Drilling
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
1. Use sharp drill bits only. For WOOD, use twist
drill bits, spade bits, power auger bits, or hole
saws. For METAL, use steel twist drill bits or
hole saws.
2. Always apply pressure in a straight line with the
bit. Use enough pressure to keep drill biting, but
do not push hard enough to stall the motor or
deflect the bit.
3. Hold tool firmly with both hands to control the
twisting action of the drill.
4. IF DRILL STALLS, it is usually because
it is being overloaded or improperly used.
RELEASE TRIGGER IMMEDIATELY, remove
drill bit from work, and determine cause
of
stalling. DO NOT CLICK TRIGGER ON
AND OFF IN AN ATTEMPT TO START A
STALLED DRILL — THIS CAN DAMAGE
THE DRILL.
5. To minimize stalling or breaking through the
material, reduce pressure on drill and ease the
bit through the last fractional part of the hole.
6. Keep the motor running when pulling the bit
back out of a drilled hole. This will help prevent
jamming.
7. With variable speed drills there is no need to
center punch the point to be drilled. Use a
slow speed to start the hole and accelerate by
squeezing the trigger harder when the hole is
deep enough to drill without the bit skipping
out.
DRILLING IN METAL
Start drilling with
slow speed and increase to full
power while applying firm pressure on the tool.
A smooth even flow of metal chips indicates the
proper drilling rate. Use a cutting lubricant when
drilling metals. The exceptions are cast iron and
brass which should be drilled dry.
NOTE:
Large [5/16" (8 mm) to 1/2" (13 mm)] holes
in steel can be made easier if a pilot hole [5/32"
(4 mm) to 3/16" (5 mm)] is drilled first.
DRILLING IN WOOD
Start drilling with slow speed and increase to full
power while applying firm pressure on the tool.
Holes in wood can be made with the same twist
drills used for metal. These bits may overheat unless
pulled out frequent
ly to clear chips from the flutes.
Work that is apt to splinter should be backed up
with a block of wood.
7
Bubble Level (Fig. 3)
Your drill is equipped with a bubble level (g) that assists
you in drilling level holes.For horizontal drilling, tilt the drill
up or down as required so that the bubble floats in the
center of the parallel lines drawn on the glass. When the
bubble is centered between the lines, the drill is level.
For vertical drilling, align the drill so that the bubble floats
in the center of the bull’s-eye (h). To assure accuracy,
first place a level on your work piece and position it so
that it is level. Then, when the drill reads level, the two will
be aligned. (Any bubble level can only indicate level to the
earth’s surface).
NOTE: The fluid in the bubble level vial is mineral spirits. If
the mineral spirits gets into your eyes, flush eyes with
water. If irritation occurs, seek medical attention. If the vial
fluid comes into contact with your skin, remove
contaminated clothing and remove excess fluid. Rinse
thoroughly with water followed by washing with soap and
water. If irritation occurs, seek medical attention. If vial
fluid is inhaled, immediately get fresh air. If difficulty
breathing, seek medical attention.
E NGLISH
8
REMOVAL OF KEYED CHUCK (FIG. 4)
Tighten the chuck around the shorter end of a hex
key (not supplied) of 1/4" (6 mm) or greater size.
Using a soft hammer, strike the key sharply in the
counterclockwise direction when viewed from the
front of the tool. This will loosen the chuck so that it
can be removed by hand.
KEYED CHUCK INSTALLATION (FIG. 5)
Screw the chuck on by hand as far as it will go.
Insert the shorter end of a hex key (not supplied)
of 1/4" (6 mm) or greater size and strike it in the
clockwise direction with a soft hammer.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-ups
or when making repairs. Be sure the
trigger switch is in the OFF position. An
accidental start-up can cause injury.
Motor Brushes
DEWALT uses an advanced brush system which
automatically stops the drill when the brushes wear
out. This prevents serious damage to the motor.
New brush assemblies are available at authorized
D
EWALT service centers. Always use identical
replacement parts.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by D
EWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only D
EWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
CAUTION: To reduce the risk of injury,
the following accessories should be
used only in sizes up to the maximums
shown in the table below.
MAXIMUM RECOMMENDED CAPACITIES
Drill capacity 1/2" (13 mm)
R.P.M. 0-2,500
Bits, metal drilling 1/2" (13 mm)
Wood, flat boring 1" (25.4 mm)
Hole saws 1-1/8" (28.4 mm)
Keyed Chuck
(fig. 4, 5)
The DWD112E features a keyed chuck (d). To insert
a drill bit or other accessory, follow the step slisted
below.
1. Open the chuck jaws by turning collar by hand
and insert the shank of the bit about 3/4"
(19 mm) into chuck. Tighten the chuck collar by
hand.
2. Place chuck key in each of the three holes, and
tighten in clockwise direction. It’s important to
tighten chuck with all three holes.
To releas
e the bit, turn the chuck counterclockwise
in just one hole, then loosen the chuck by hand.
在所有下列警告中术语“电动工具”指市电驱动（有线）
电动工具或电池驱动（无线）电动工具。
a) 工作场地的安全
1) 保持工作场地清洁和明亮。混乱和黑暗的场地会引发
事故。
2) 不要在易爆环境，如有易燃液体、气体或粉尘的环境
下操作电动工具。电动工具产生的火花会点燃粉尘或
气体。
3) 让儿童和旁观者离开后操作电动工具。注意力不集中
会使操作者失去对工具的控制。
电动工具通用安全警告
警告！阅读所有警告和所有说明。不遵照以下警
告和说明会导致电击、着火和/或严重伤害。
保存所有警告和说明书以备查阅
DWD112E
DWD112E
暴露在噪声中会引起听力
损伤。
使用随工具提供的辅助手柄。操作失手会引起人身伤
害。
当在钻削附可能触及暗线或其自身软线之处进行
操作时，要通过绝缘握持面来握持工具。钻削附
碰到带电导线会使工具外露的金属零带电从而使
操作者受到电击。
6) 保持切削刀具锋利和清洁。保养良好的有锋利切削刃
的刀具不易卡住而且更容易控制。
7) 按照使用说明书，考虑作业条和进行的作业来使用
电动工具、附和工具的刀头等。将电动工具用于那
些与其用途不符的操作可能会导致危险。
e) 维修
1) 将你的电动工具送交专业维修人员，使用同样的备
进行修理。这样将确保所维修的电动工具的安全性。
b) 电气安全
1) 电动工具插头必须与插座相配。绝不能以任何方式
改装插头。需接地的电动工具不能使用任何转换插
头。未经改装的插头和相配的插座将减少电击危险。
2) 避免人体接触接地表面，如管道、散热片、冰箱。
如果你身体接地会增加电击危险。
3) 不得将电动工具暴露在雨中或潮湿环境中。水进入
电动工具将增加电击危险。
4) 不得滥用电线。绝不能使用电线搬运、拉动电动工
具或拔出其插头。使电线远离热源、油、锐边或运
动部。受损或缠绕的软线会增加电击危险。
5) 当在户外操作电动工具时，使用适合户外使用的外
接软线。适合户外使用的软线将减少电击的危险。
6) 如果在潮湿的环境下操作电动工具是不可避免的，应
使用剩余电流动作保护器 (RCD)。使用 RCD 可减小
电击的危险。
c) 人身安全
1) 保持警觉，当操作电动工具时关注所从事的操作并
保持清醒。当你感到疲倦，或在有药物、酒精或治
疗反应时，不要操作电动工具。在操作电动工具时
瞬间的疏忽会导致严重人身伤害。
2) 使用个人防护装置。始终佩戴护目镜安全装置，
诸如适当条下使用防尘面具、防滑安全鞋、安全
帽，听力防护等装置能减少人身伤害。
3) 防止意外起动。确保开关在连接电源和/或电池盒、
拿起或搬运工具时处于关断位置。手指放在已经接
通电源的开关上或开关处于接通时插入插头可能会
导致危险。
4) 在电动工具接通之前，拿掉所有调节钥匙或扳手。
遗留在电动工具旋转零上的扳手或钥匙会导致人
身伤害。
5) 手不要伸得太长。时刻注意立足点和身体平衡。这
样在意外情况下能很好地控制电动工具。
6) 着装适当。不要穿宽松的衣或佩戴饰品。让衣、
手套和头发远离运动部。宽松衣、配饰或长发
可能会卷入运动部中。
7) 如果提供了与排屑装置、集尘设备连接用的装置，
要确保这些装置连接完好且使用得当。使用这些装
置可减少碎屑引起的危险。
d) 电动工具的使用和注意事项
1) 不要滥用电动工具，根据用途使用适当的电动工具。
选用适当设计的电动工具会使你工作更有效、更安
全。
2) 如果开关不能接通或关断工具电源，则不能使用该
电动工具。不能用开关来控制的电动工具是危险的
且必须进行修理。
3) 在进行任何调节、更换附或贮存电动工具之前，
必须从电源上拔掉插头和/或使电池盒与工具脱开。
这种防护性措施将减少工具意外起动的危险。
4) 将闲置不用的电动工具贮存在儿童所及范围之外，
并且不要让不熟悉电动工具或对这些说明不了解的
人操作电动工具。电动工具在未经培训的用户手中
是危险的。
5) 保养电动工具。检查运动部是否调整到位或卡住、
检查零破损情况和影响电动工具运行的其他状况。
如有损坏，电动工具应在使用前修理好。许多事故
由维护不良电动工具所引发。
(DWD112E)
匙
匙
DWD112E
制
造商：百得美国公司
地址：701 E Joppa Rd, TW050 MD21286, Towson, 美国
产地：江苏南通
N
508845
12
/2016
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
他の言語で
- English: DeWalt DWD112 User manual
関連論文
その他のドキュメント
-
Hikoki D13VL ユーザーマニュアル
-
Hilti DD 150-U 取扱説明書
-
Makita 6411 ユーザーマニュアル
-
Nautilus T684 Assembly & Owner's Manual
-
Milwaukee M12 CD ユーザーガイド
-
Milwaukee Milwaukee PLH 20 Original Instructions Manual
-
RIDGID เครื่องมือทำความสะอาดท่อระบายน้ำรอบผนังท่อ FlexShaft รุ่น K9-12 ユーザーマニュアル
-
Stanley ESAFOR MK II 74290 Hydro Pneumatic Power Tool ユーザーマニュアル