Cognex In-Sight 7800 ユーザーマニュアル

In-Sight

®

7000 Gen2 Series

Vision System

Manual

2020 June 15

Revision: 5.9.2.1

Regulations and Conformity

Note: For the most current CE declaration and regulatory conformity

information, see the Cognex support site: cognex.com/support.

Safety and Regulatory

Manufacturer

Cognex Corporation

One Vision Drive

Natick, MA 01760 USA

In-Sight 7500/7500C: Regulatory Model 1AAB

In-Sight 7501/7501C: Regulatory Model 1AAB

In-Sight 7600/7600C: Regulatory Model 1AAB

In-Sight 7800/7800C: Regulatory Model 1AAB

In-Sight 7801/7801C: Regulatory Model 1AAB

In-Sight 7802/7802C: Regulatory Model 1AAB

In-Sight 7802P: Regulatory Model R00063

In-Sight 7900/7900C: Regulatory Model 1AAB

In-Sight 7901/7901C: Regulatory Model 1AAB

In-Sight 7902/7902C: Regulatory Model 1AAB

In-Sight 7902P: Regulatory Model R00063

In-Sight 7905/7905C: Regulatory Model R00063

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take immediate measures. This

equipment complies with the essential requirements of the EU Directive 2014/30/EU.

Declarations are available from your local representative.

EU RoHS Compliant to the most recent applicable directive.

FCC

FCC Part 15, Class A

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

1

Safety and Regulatory

Korea In-Sight 7500/7500C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7501/7501C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7600/7600C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7800/7800C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7801/7801C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7802/7802C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7802P: Regulatory Model R00063: R-REM-CGX-R00063

In-Sight 7900/7900C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7901/7901C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7902/7902C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB

In-Sight 7902P: Regulatory Model R00063: R-REM-CGX-R00063

In-Sight 7905/7905C: Regulatory Model R00063: R-REM-CGX-R00063

This device is certified for office use only and if used at home, there can be frequency

interference problems.

TÜV

In-Sight 7500/7500C: Regulatory Model 1AAB

In-Sight 7501/7501C: Regulatory Model 1AAB

In-Sight 7600/7600C: Regulatory Model 1AAB

In-Sight 7800/7800C: Regulatory Model 1AAB

In-Sight 7801/7801C: Regulatory Model 1AAB

In-Sight 7802/7802C: Regulatory Model 1AAB

In-Sight 7802P: Regulatory Model R00063

In-Sight 7900/7900C: Regulatory Model 1AAB

In-Sight 7901/7901C: Regulatory Model 1AAB

In-Sight 7902/7902C: Regulatory Model 1AAB

In-Sight 7902P: Regulatory Model R00063

In-Sight 7905/7905C: Regulatory Model R00063

NRTL: TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 61010-1.

CB report available upon request. TÜV SÜD AM, IEC/EN 61010-1.

2

China RoHS

Hazardous Substances 有害物质

Part Name

部件名称

Lead (Pb)

铅

Mercury

(Hg)

汞

Cadmium

(Cd)

镉

Hexavalent

Chromium

(Cr (VI))

六价铬

Polybrominated

biphenyls (PBB)

多溴联苯

Polybrominated

diphenyl ethers

(PBDE)

多溴二苯醚

Regulatory

Model 1AAB

Regulatory

Model

R00063

X O O O O O

This table is prepared in accordance with the provisions of SJ/T 11364.

这个标签是根据 SJ / T 11364 的规定准备的。

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the

limit requirement of GB / T26572 - 2011.

表示本部件所有均质材料中含有的有害物质低于 GB / T26572 - 2011 的限量要求。

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this

part is above the limit requirement of GB / T26572 - 2011.

表示用于本部件的至少一种均质材料中所含的危害物质超过 GB / T26572 - 2011 的限制要求。

3

For European Community Users

Cognex complies with Directive 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment

(WEEE).

Thisproduct has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health and the

environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment and to

diminish the pressure on the natural resources, we encourage you to use the

appropriate take-back systems for product disposal. Those systems will reuse or

recycle most of the materials of the product you are disposing in a sound way.

The crossed out wheeled bin symbol informs you that the product should not

be disposed of along with municipal waste and invites you to use the appropriate

separate take-backsystems for product disposal.

If you need more information on the collection, reuse, and recycling systems, please

contact your local or regional waste administration.

You may also contact your supplier for more information on the environmental

performance of thisproduct.

4

Precautions

To reduce the risk of injury or equipment damage when you install the Cognex

product, observe the following precautions:

l The vision system requires a UL or NRTL listed power supply with a 24VDC

output that meets the following rating requirements:

l At least 2A continuous current.

l A maximum short circuit current of less than 8A.

l A maximum power of lessthan 100VA and marked as a Limited

Power Source (LPS) or National Electrical Code (NEC) Class 2.

Any other voltage creates a risk of fire or shock and can damage the

components. Applicable national and local wiring standards and rules must

be followed.

l Thisproduct is intended for industrial use in automated manufacturing or

similar applications.

l The safety of any system incorporating this product is the responsibility of

the assembler of the system.

l Do not install Cognex products where they are exposed to environmental

hazards such as excessive heat, dust, moisture, humidity, impact, vibration,

corrosive substances, flammable substances, or static electricity.

l Route cables and wires away from high-current wiring or high-voltage

power sources to reduce the risk of damage or malfunction from the

following causes: over-voltage, line noise, electrostatic discharge (ESD),

power surges, or other irregularities in the power supply.

5

l Do not expose the image sensor to laser light. Image sensors can be

damaged by direct, or reflected, laser light. If your application requires laser

light that might strike the image sensor, use a lens filter at the corresponding

laser wavelength. For suggestions, contact your local integrator or

application engineer.

l Thisproduct does not contain user-serviceable parts. Do not make

electrical or mechanical modifications to product components.

Unauthorized modifications can void your warranty.

l Changes or modifications not expressly approved by the party responsible

for regulatory compliance could void the user’s authority to operate the

equipment.

l Include service loops with cable connections.

l Ensure that the cable bend radius begins at least six inches from the

connector. Cable shielding can be degraded or cables can be damaged or

wear out faster if a service loop or bend radius istighter than 10X the cable

diameter.

l Thisdevice should be used in accordance with the instructions in this

manual.

l All specifications are for reference purposes only and can change without

notice.

6

In-Sight 7500/7600 Series &

7800/7801/7802/7900/7901/7902

7

In-Sight 7802P/7902P/7905

8

Installation

Read this section to learn how the vision system connects to its standard

components and accessories. For a list of options and accessories, contact your

Cognex sales representative.

Installation procedures and specifications are presented in detail in the In-Sight

®

7000 Gen2 Series Vision System Reference Guide, which is installed with In-Sight

Explorer software.

Note: Cables are sold separately.

CAUTION: All cable connectors are keyed to fit the connectors on the vision

system. Do not force the connections or damage may occur.

9

Install the C-Mount Lens and Cover

(COV-7000-CMNT or COV-7000-CMNT-EX)

Complete the following steps to installa C-Mount lens and cover to the vision system.

The C-Mount covers are optional accessories and required for IP67 protection.

Note:

l When using a C-Mount lens, the following restrictions apply:

l Maximum thread length is 5.25mm.

l The C-Mount lens threads and body cannot protrude more

than 6.5mm in length into the vision system when screwed in

unless the diameter of the back lens is smaller than

14.75mm. If the C-Mount lens threads and body protrude

more than 6.5mm, you can add a spacer between the lens

and vision system. However, the spacer decreases the

working distance.

l If using the COV-7000-CMNT cover, the maximum lens length is

41mm, the maximum lens body diameter is 36.5mm and the

maximum diameter including locking screws is47mm.

l If using the COV-7000-CMNT-EX cover, the maximum lens length is

62mm, the maximum lens body diameter is 36.5mm and the

maximum diameter including locking screws is46.5mm.

1. Remove the rubber faceplate covering the image sensor window, if

present.

2. Remove the protective film covering the threaded lens opening, if present.

10

3. Place the adapter on the faceplate of the vision system. Insert the four

adapter screws and tighten; the maximum torque is 0.90 Nm (8 in-lb).

4. Thread the lens into the vision system.

5. Attach the cover to the vision system. Rotate the cover clockwise

approximatelyseven degrees to lock it.

11

Install the C-Mount Lens and Cover (COV-

7000-CMNT-LG)

Complete the following steps to installa C-Mount lens and cover to the vision system.

The C-Mount cover is an optional accessory and required for IP67 protection.

Note:

l The COV-7000-CMNT-LG cover is only supported with the In-Sight

7802P, 7902P and 7905 vision systems.

l When using a C-Mount lens, the following restrictions apply:

l Maximum thread length is 5.25mm.

l The C-Mount lens threads and body cannot protrude more

than 6.5mm in length into the vision system when screwed in

unless the diameter of the back lens is smaller than

14.75mm. If the C-Mount lens threads and body protrude

more than 6.5mm, you can add a spacer between the lens

and vision system. However, the spacer decreases the

working distance.

l If using the COV-7000-CMNT-LG cover, the maximum lens length is

77mm, the maximum lens body diameter is 55mm and the maximum

diameter including locking screws is55mm.

1. Remove the rubber faceplate covering the image sensor window, if

present.

2. Remove the protective film covering the threaded lens opening, if present.

3. Place the adapter on the faceplate of the vision system. Insert the four

adapter screws and tighten; the maximum torque is 0.90 Nm (8 in-lb).

12

4. Thread the lens into the vision system.

5. (Optional) For longer lenses, the C-Mount cover extender accessory (COV-

7000-CMNT-LGX) can be used to add 30mm in length to the C-Mount

cover. If using the cover extender, attach it to the vision system and rotate

the cover extender clockwise approximatelythirteen degrees to lock it.

6. Attach the cover to the vision system. Rotate the cover clockwise

approximatelythirteen degrees to lock it.

13

Install the Converter Mounting Bracket

(ISB-7000-7K)

Complete the following steps to attach the converter accessory mounting bracket

(ISB-7000-7K) to the vision system.

Note: When attaching the vision system to the mounting bracket, use the M3

screws supplied with the mounting kit. If using the 1/4 - 20 or M6 screw holes,

the thread length of the screw should not exceed 7mm.

CAUTION: The vision system should be grounded, either by mounting the

vision system to a fixture that is electrically grounded or by attaching a wire

from the vision system’s mounting fixture to frame ground or Earth ground. If a

ground wire isused, it should be attached to one of the four mounting points on

the back plate of the vision system and not to the mounting points on the front

of the vision system.

1. Align the converter mounting bracket with the mounting holes on the vision

system.

2. Insert the M3 screws into the mounting holes and tighten using a 2.5mm hex

wrench. The maximum torque is 0.90 Nm (8 in-lb).

14

Connect the External Light Cable (Optional)

The vision system's LIGHTconnector is used to connect the External Light cable to

an external lighting device, providing power and strobe control. The External Light

cable can be connected to either a continuous or strobed lighting device.

Note: The vision system supports connecting an integrated illumination

accessory to the vision system's faceplate and connecting an external light to

the vision system's LIGHT connector, but does not support using both lighting

devices simultaneously.

1. Remove the protective cap from the LIGHT connector, if present.

2. Connect the External Light cable’s M12 connector to the vision system's

LIGHT connector.

3. Connect the other end of the Light cable to an external lighting device (for

example, a strobe light).

15

Connect the Breakout Cable

CAUTION: To reduce emissions, connect the far end of the Breakout cable

shield to frame ground.

Note:

l Perform wiring or adjustments to I/O devices when the vision system

is not receiving power.

l You can cut exposed wires short or trim wire ends. You also can tie

the wires back if you use a tie made of non-conductive material. Keep

bare wires separated from the +24VDC wire.

l When using the 15 meter Breakout cable, full 24VDC voltage must be

maintained at the input leads of the Breakout cable when the vision

system isoperating.

1. Verifythat the 24VDC power supplyis unplugged and not receiving power.

2. Optionally, connect the I/O wires to an appropriate device (for example, a

PLC or a serial device).

3. Attach the Breakout cable's +24VDC (Red wire) and GND (Black wire) to

the corresponding terminals on the power supply.

CAUTION: Never connect voltages other than 24VDC. Always

observe the polarity shown.

4. Connect the Breakout cable's M12 connector to the vision system PWR

connector.

5. Restore power to the 24VDC power supplyand turn it on if necessary.

16

Connect the Ethernet Cable

CAUTION: The Ethernet cable shield must be grounded at the far end.

Whatever thiscable is plugged into (typicallya switch or router) should have a

grounded Ethernet connector. A digital voltmeter should be used to validate

the grounding. If the far end device is not grounded, a ground wire should be

added in compliance with local electrical codes.

1. Connect the Ethernet cable's M12 connector to the vision system ENET

connector.

2. Connect the Ethernet cable’s RJ-45 connector to a switch/router or PC, as

applicable.

17

Install Software and Documentation

To configure an In-Sight vision system, In-Sight Explorer software must be installed

on a networked PC. In-Sight software is available as a free download from the In-

Sight support site: cognex.com/support/insight.

Log on to the Vision System

1. Open the In-Sight Explorer software.

2. From the Get Connected Application Step, select your In-Sight vision

system from the Select an In-Sight Sensor or Emulator group box and click

Connect.

18

7500 Series Vision System Specifications

Specifications 7500 7500C 7501 7501C

Power

Consumption

24VDC ±10%, 1.5A maximum.

Power Output 24VDC @ 750mA maximum to external light.

Case

Temperature

1

0°C to 50°C (32°F to 122°F)

Storage

Temperature

-20°C to 80°C (-4°F to 176°F)

Humidity < 80% non-condensing

Protection IP67 with all cables properly attached (or the provided connector plug installed), the IP67-rated

cover properly installed, and the Micro SD card cover fastened in place.

Shock (Shipping

and Storage)

IEC 60068-2-27: 18 shocks (3 shocks in each polarity in each (X, Y, Z) axis) 80 Gs (800m/s

2

at

11ms, half-sinusoidal) with cables or cable plugs and a 150 gram or lighter lens attached.

Vibration

(Shipping and

Storage)

2

IEC 60068-2-6: vibration test in each of the three main axis for 2 hours @ 10 Gs (10 to 500 Hz

at 100m/s

2

/ 15mm) with cables or cable plugs and a 150 gram or lighter lens attached.

1

To verify case temperature, use the EV GetSystemConfig(“Internal.Temperature”) Extended Native Mode

command or GetSystemConfig(“Internal.Temperature”) spreadsheet function. When issued, it returns the vision

system internal temperature in degrees Celsius, which is approximately 3 to 5 degrees above the vision system

case temperature. For more information, see the In-Sight

®

Explorer Help file. A thermal scanner can also be used to

determine the vision system case temperature. Additional cooling measures are required if the case temperature

cannot be kept below 50°C. Examples of such measures include: extra heat sinking and/or air movement.

2

Before you ship this product or any machinery that contains it, remove lenses that weigh more than 150 grams.

19

ページが読み込まれています...

Cognex In-Sight 7800 ユーザーマニュアル

Cognex In-Sight 7800 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント