Philips HD8650/27 ユーザーマニュアル

HD8650

5

19

14

10

12

8

9

11

6

3

4

13

21

20

17

18 16

15

7

21

1

HD8650

ENGLISH 6

繁體中文 27

简体中文 47

6

Table of contents

Introduction 6

General description 7

Important 7

Danger 7

Warning 7

Caution 8

Electromagnetic elds (EMF) 8

Before rst use 8

Installing the machine 8

Preparing for use 9

Filling the water tank 9

Filling the coffee bean container 9

Heating up the machine 10

Automatic rinsing cycle 11

Installing the Intenza+ water lter 12

Using the machine 12

Brewing coffee 13

Adjusting the machine 13

Adjusting the grinding degree 13

Adjusting the coffee volume 14

Cleaning and maintenance 14

Cleaning the brewing unit 15

Lubrication 17

Descaling the machine 18

Descaling procedure 18

Preparation 18

Descaling cycle 19

Rinsing cycle 19

If you are unable to nish the descaling cycle 21

Meaning of light signals 21

Recycling 24

Guarantee and support 24

Ordering maintenance products 24

Troubleshooting 24

Technical specications 26

Introduction

Congratulations on buying this fully automatic Philips espresso machine!

To fully benet from the support that Philips offers, please register your

product at www.philips.com/welcome. The machine is suitable for

preparing espresso coffee using whole coffee beans. In this user manual you

nd all the information you need to install, use and maintain your machine.

ENGLISH

General description (Fig. 1)

1 Control panel

2 Coffee button

3 Descaling light

4 Warning light

5 2-cup light

6 ’Water tank empty’ light

7 On/off button with light

8 Water tank

9 Coffee spout

10 Drip tray cover

11 ’Drip tray full’ indicator

12 Drip tray

13 Coffee grounds container

14 Brewing unit

15 Maintenance door

16 Grinding degree adjustment knob

17 Ceramic coffee grinder

18 Coffee bean container

19 Grinding degree adjustment tool

20 Lid of coffee bean container

21 Mains cord

Important

Read and follow the safety instructions carefully and only use the machine

as described in this user manual to avoid accidental injury or damage due to

improper use of the machine. Keep this user manual for future reference.

Danger

- Never immerse the machine in water or any other liquid.

- Never direct the steam wand at the body as this causes scalding.

- Never insert body parts or objects into the coffee grinder.

Warning

- Check if the voltage indicated on the machine corresponds to the local

mains voltage before you connect the machine.

- Connect the machine to an earthed wall socket.

- This machine is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

- Children should be supervised to ensure that they do not play with

the machine.

- Keep the machine and its cord out of the reach of children.

- This machine is designed to grind beans and brew coffee. Use it

correctly and with care to avoid scalding by hot water and steam.

- Do not pour liquids on the mains cord connector.

- Do not use the machine if the plug, the mains cord or the machine

itself is damaged.

- If the mains cord is damaged, you must have it replaced by Philips,

a service centre authorised by Philips or similarly qualied persons

in order to avoid a hazard.

ENGLISH 7

Caution

- Always return the machine to a service centre authorised by Philips for

examination or repair. Do not attempt to repair the machine yourself,

otherwise your guarantee becomes invalid.

- Always put the machine on a at and stable surface. Keep it in upright

position, also during transport.

- Do not place the machine on a hotplate or directly next to a hot oven,

heater or similar source of heat.

- Unplug the machine if problems occur during grinding or brewing and

before you clean it.

- Let the machine cool down before inserting or removing any parts.

The heating element surface is subject to residual heat after use.

- Descale the machine regularly.

- If you do not clean and descale the machine, you run the risk that the

machine stops working and that your guarantee becomes invalid.

- Never ll the water tank with warm, hot or sparkling water, as this may

cause damage to the water tank and the machine.

- Do not use aggressive cleaning agents, solvents or chemicals to clean

the machine.

- Do not keep the machine at temperatures below 0°C. Water left in

the heating system may freeze and cause damage.

- This machine is intended for normal household use only. It is not

intended for use in environments such as staff kitchens of shops, ofces,

farms or other work environments.

Electromagnetic elds (EMF)

This machine complies with all applicable standards and regulations

regarding exposure to electromagnetic elds.

Before rst use

Installing the machine

1 Remove all packaging material from the machine.

2 Place the machine on a table or worktop away from the tap, the sink

and heat sources.

3 Leave at least 15cm of free space above, behind and on both sides of

the machine.

4 Insert the small plug into the socket located on the back of the

machine.

15cm

ENGLISH8

5 Insert the plug into the wall socket.

6 Remove the protective sticker from the drip tray and slide the drip

tray into the guiding grooves in the front of the machine.

Note: Make sure the drip tray is fully inserted.

Preparing for use

Filling the water tank

1 Remove the water tank from the machine.

2 Rinse the water tank under the tap.

3 Fill the water tank with cold tap water up to the MAX indication.

Never ll the water tank with warm, hot or sparkling water, as this may

cause damage to the water tank and the machine.

4 Slide the water tank back into the machine.

Filling the coffee bean container

1 Fill the coffee bean container with espresso beans.

Only use espresso beans. Never use ground coffee, unroasted coffee

beans or caramelised coffee beans, as this may cause damage to the

machine.

ENGLISH 9

2 Put the lid on the coffee bean container.

Heating up the machine

During the initial heat-up process, fresh water ows through the internal

circuit to heat up the machine. This takes a few seconds.

1 Place a bowl under the coffee spout.

2 Press the on/off button.

3 The warning light ashes quickly to indicate there is no water in the

internal circuit.

4 Press the coffee button. The machine lets the hot water ow through

the coffee spout.

ENGLISH10

, The on/off button ashes slowly and the warning light goes out.

5 After a few seconds hot water stops coming out of the coffee spout.

, The machine is heating up.

Automatic rinsing cycle

When the machine has heated up, it performs an automatic rinsing cycle to

clean the internal circuit with fresh water. This takes approximately

one minute.

1 Place a bowl under the coffee spout.

, The on/off button ashes slowly.

2 Water ows from the coffee spout. Wait until the water stops

coming out of the coffee spout.

Note: You can stop the automatic rinsing cycle by pressing the coffee button.

3 When the on/off button lights up continuously, the machine is ready

to brew coffee.

Note: The automatic rinsing cycle also takes place 15 minutes after the

appliance switches to standby mode or switches off.

Note: The rst cups of coffee may be a bit watery, this is normal. The machine

needs to complete a few brewing cycles to optimise its settings.

ENGLISH 11

Installing the Intenza+ water lter

We advise you to install the Intenza+ water lter as this prevents scale

build-up in your machine. You can buy the Intenza+ water lter separately.

For more details, see chapter ‘Guarantee and support’, section ‘Ordering

maintenance products’.

1 Remove the small white lter from the water tank and store it in a

dry place.

Note: Please keep the small white lter for future use. You will need it for the

descaling process.

2 Remove the lter from its packaging and immerse it in cold water

with the opening pointing upwards. Press the sides of the lter gently

to let out the air bubbles.

3 Turn the knob of the lter to the setting that corresponds to the

water hardness of the area you live in.

A Soft water

B Hard water (default)

C Very hard water

Note: You can test the water hardness with a water hardness test strip.

4 Place the lter in the empty water tank. Press it down until it cannot

move any further.

5 Fill the water tank with fresh water up to the MAX indication and

slide it into the machine.

6 Let the machine brew a few coffees (see chapter ‘Using the machine’,

section ‘Brewing coffee’).

7 Rell the water tank with fresh water up to the MAX indication and

slide it back into the machine.

, The on/off button lights up continuously.

The machine is ready for use.

Using the machine

To guarantee perfect coffee, the machine regularly rinses its inner circuit

with water. This automatic rinsing cycle takes place 15 minutes after the

appliance switches to standby mode or switches off. During the automatic

rinsing cycle, some of the water ows through the inner circuit directly into

the drip tray. Empty the drip tray regularly.

ENGLISH12

Brewing coffee

1 Make sure the on/off button lights up green continuously.

2 Place 1 or 2 cups on the drip tray cover.

3 Press the coffee button.

Note: You can interrupt the brewing cycle at any time by pressing the coffee

button.

- Press the coffee button once to brew 1 cup of coffee.

, The machine grinds the required amount of coffee beans for one cup

and then brews one cup of coffee.

- Press the coffee button twice to brew 2 cups of coffee.

, The 2-cup light lights up. The machine grinds the required amount

of coffee beans for one cup and then lls both cups half. Then the

machine grinds coffee beans for one cup again and lls both cups

fully.

Note: When the machine is left in standby mode, it switches off automatically

after 30 minutes.

Adjusting the machine

You can adjust the grinding degree and coffee volume to obtain coffee that

is perfectly customised to your taste.

Adjusting the grinding degree

You can adjust the grinding degree of the machine. At each grinding degree

selected, the ceramic coffee grinder guarantees a perfectly even grind

for every cup of coffee you brew. It preserves the full coffee aroma and

delivers the perfect taste to every cup.

1 Press the grinding degree adjustment knob rmly (1) and then turn it

one notch at a time (2). There are 5 different grinding degree settings

you can choose from. The smaller the dot, the stronger the coffee.

The difference becomes noticeable after you have brewed 2-3 cups

of coffee at the new setting.

Do not turn the grinding degree adjustment knob more than one notch

at a time to prevent damage to the grinder.

2

1

ENGLISH 13

Adjusting the coffee volume

You can adjust the coffee volume to your taste and the size of your cups.

The coffee button can be programmed.

1 Place a cup on the drip tray cover.

2 Press and hold the coffee button for a few seconds. Release the

button when the machine starts to grind coffee beans.

, The 2-cup light and the on/off button ash slowly.

3 Press the coffee button again when the cup contains the desired

amount of coffee.

The machine automatically saves the new setting.

Cleaning and maintenance

Regular cleaning and descaling prolongs the lifetime of your machine and

ensures optimum quality and taste of your coffee.

Do not immerse the machine in water or any other liquid.

Never use scouring pads, abrasive cleaning agents or aggressive liquids to

clean the machine.

Always unplug the machine and let it cool down before you clean it.

Note: None of the detachable parts are dishwasher-proof. Rinse them under

the tap.

Note: The drip tray collects the water that comes out of the coffee spout during

each rinsing cycle and coffee that might be spilled during coffee preparation.

Empty and clean the drip tray regularly and when the ‘drip tray full’ indicator

is raised.

Caution: Never remove the drip tray when the machine has just been

switched on. Wait a few minutes until the machine has performed a

rinsing cycle.

ENGLISH14

Cleaning the brewing unit

Do not clean the brewing unit in the dishwasher and do not use

washing-up liquid or a cleaning agent to clean it.

Clean the brewing unit once a week.

1 Switch off the machine and unplug it.

2 Remove the coffee grounds container from the machine.

3 Open the maintenance door.

4 Press the PUSH button (1) and pull at the grip of the brewing unit

(2) to remove it from the machine.

5 Clean the coffee exit duct thoroughly with a spoon handle or

another round-tipped kitchen utensil.

6 Rinse the outside of the brewing unit under a lukewarm tap and

clean the upper lter carefully.

Never use any washing-up liquid or other cleaning agent to clean the

brewing unit.

Do not dry the brewing unit with a cloth to prevent bres from

collecting inside the brewing unit. After rinsing, just shake excess water

off the brewing unit or let it air-dry.

1

2

ENGLISH 15

7 Before you slide the brewing unit back into the machine, make sure

the two reference signs on the side match. If they do not match,

perform the following step:

- Make sure the lever is in contact with the base of the brewing unit.

8 Make sure the locking hook of the brewing unit is in the correct

position.

Note: You can nd the locking hook on the back of the brewing unit (the side

without the word “push”), at the top of the horizontal edge.

- To position the hook correctly, push it upwards until it is in uppermost

position.

ENGLISH16

Note: The hook is not correctly positioned if it is still in bottommost position.

9 Slide the brewing unit back into the machine along the guiding rails

on the sides until it clicks into position.

Do not press the PUSH button.

10 Close the maintenance door.

11 Slide the coffee grounds container back into the machine.

Lubrication

For optimal performance of the machine, lubricate the brewing unit after

it has brewed 500 cups of coffee or once every 3 months. Contact the

Philips Saeco hotline to buy lubricant.

1 Switch off the machine and unplug it.

2 Follow steps 2 to 4 in section ‘Cleaning the brewing unit’ to

remove the brewing unit from the machine.

3 Apply some lubricant around the shaft in the bottom of the

brewing unit.

ENGLISH 17

4 Apply some lubricant to both sides of the part shown in

the illustration.

5 Follow steps 7 to 11 in section ‘Cleaning the brewing unit’ to

place the brewing unit and the coffee grounds container back

into the machine.

Descaling the machine

Scale builds up inside the machine during use. It is essential to descale the

machine when the orange descaling light lights up continuously. Only use

the special Saeco descaling solution to descale the machine. The Saeco

descaling solution is designed to ensure optimal performance of the

machine. You can buy the Saeco descaling solution in the online shop at

www.shop.philips.com/service.

Note: The use of other descaling products may cause damage to the machine

and leave residues in the water.

Never drink the water with descaling mixture that you pour into the

water tank or any water with residues that comes out of the machine

during the descaling procedure.

Descaling procedure

The descaling procedure lasts 30 minutes and consists of a descaling cycle

and a rinsing cycle. When the orange descaling light lights up continuously,

you need to descale the machine.

Note: Do not remove the brewing unit during the descaling procedure.

Preparation

1 Switch off the machine.

If you do not switch off the machine, you cannot enter the descaling cycle.

2 Empty the drip tray and place it back.

3 Empty the water tank and remove the Intenza+ water lter (if present).

Pour the entire bottle of descaling solution into the water tank.

4 Add water to the descaling solution in the water tank up to

the MAX indication.

ENGLISH18

5 Place a bowl under the coffee spout.

Descaling cycle

1 Press the coffee button for approximately 5 seconds.

, The orange descaling light ashes slowly during the entire descaling

cycle.

, After each interval of one minute, the descaling solution ows out

of the coffee spout. This happens several times until the water tank

is completely empty.

Note: If you want to interrupt the ow of the descaling solution press the

coffee button.To restart the ow of the descaling solution, press the coffee

button again.

2 The ‘water tank empty’ light lights up continuously.

3 Empty the drip tray and place it back.

Rinsing cycle

1 Remove the water tank from the machine and rinse it.

5 sec

ENGLISH 19

2 Fill the water tank with fresh tap water up to the MAX indication

and slide the water tank back into the machine.

3 Empty the bowl and place it back under the coffee spout.

Note: The orange descaling light ashes twice continuously.

4 Let hot water ow out of the coffee spout until the orange descaling

light goes out and the on/off button ashes.

, The machine is heating up and it performs an automatic rinsing cycle.

Note: If you want to interrupt the water ow press the coffee button.To restart

the water ow, press the coffee button again.

ENGLISH20

ページが読み込まれています...

Philips HD8650/27 ユーザーマニュアル

このマニュアルも適しています

Philips HD8650/27 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント