Philips HD8652/57 ユーザーマニュアル

HD8652

HD8652 2100 FRONT COVER A5 BW.indd 1 29-01-16 16:07

English 5

简体中文 32

繁體中文 56

Memo

Milk

clean

1 3

2 4

5

6

7

8

9

10

11

12

13

16

17

18

20

21

19

14

15

2523 2422

26

27

2830

31

32

29

1

English

Contents

Introduction 6

Important 6

Warning 6

Caution 7

Electromagnetic fields (EMF) 7

Machine overview (Fig. 1) 7

First installation 8

Installing the machine 8

Filling the water tank 9

Filling the coffee bean container 10

Heating up the machine 10

Installing the Intenza+ water filter 11

Using the machine 11

Brewing 1 or 2 cups of espresso 12

Brewing milk- based beverages 12

Brewing cappuccino 12

Frothing milk 13

Hot water 14

Adjusting the machine 14

Adjusting the grinding degree 14

Adjusting the coffee volume with the MEMO function 15

Adjusting the cappuccino volume with the MEMO function 15

Cleaning and maintenance 15

Quick clean of the milk system 16

Cleaning the automatic milk frother (daily) 16

Full milk carafe cleaning with milk circuit cleaner (monthly) 16

Cleaning the brew group 19

Lubrication 21

Descaling the machine 22

Descaling procedure 22

Preparation 22

Descaling cycle 23

Rinsing cycle 23

Interruption of the descaling process 24

Meaning of light signals 25

Troubleshooting 27

Recycling 30

Guarantee and support 30

Ordering maintenance products 30

Technical specifications 30

5

English

Introduction

Dear customer, we thank you for buying this Philips 2100 series automatic

espresso machine! To fully benefit from the support that Philips offers,

please register your product at www.philips.com/welcome. The machine is

suitable for preparing espresso coffee using whole coffee beans. It can also

dispense steam and hot water. In this user manual you find all the

information you need to install, use, maintain and get the best out of your

machine.

For more product information and instruction videos, have a look on our

website www.philips.com/support.

Important

This machine is equipped with safety features. Nevertheless, read and

follow the safety instructions carefully and only use the machine as

described in these instructions, to avoid accidental injury or damage due to

improper use of the machine. Keep this user manual for future reference.

Warning

-

Connect the machine to a wall socket with a voltage matching the

technical specifications of the machine.

-

Connect the machine to an earthed wall socket.

-

Do not let the power cord hang over the edge of a table or counter, or

touch hot surfaces.

-

Never immerse the machine, mains plug or power cord in water (danger

of electrical shock).

-

Do not pour liquids on the power cord connector.

-

Never direct the hot water jet towards body parts: danger of burns.

-

Do not touch hot surfaces. Use handles and knobs.

-

Remove the mains plug from the wall socket to switch off the machine.

-

If a malfunction occurs.

-

If the machine will not be used for a long time.

-

Before cleaning the machine.

-

Pull on the plug, not on the power cord.

-

Do not touch the mains plug with wet hands.

-

Do not use the machine if the mains plug, the power cord or the machine

itself is damaged.

-

Do not make any modifications to the machine or its power cord.

-

Only have repairs carried out by a service center authorized by Philips to

avoid a hazard.

-

The machine should not be used by children younger than 8 years old.

-

This machine can be used by children aged from 8 years and above and

by persons with reduced physical, sensory or mental capabilities or lack

of experience and knowledge if they have been given supervision or

instruction concerning use of the machine in a safe way and if they

understand the hazards involved.

-

Cleaning and user maintenance shall not be made by children unless

they are older than 8 and supervised.

6

English

-

Keep the machine and its cord out of the reach of children aged less than

8 years.

-

Children should be supervised to ensure that they do not play with the

machine.

-

Never insert fingers or other objects in the coffee grinder.

Caution

-

This machine is intended for normal household use only. It is not

intended for use in environments such as staff kitchens of shops, offices,

farms or other work environments.

-

Always put the machine on a flat and stable surface. Keep it in upright

position, also during transport.

-

Do not place the machine on a hotplate or directly next to a hot oven,

heater or similar source of heat.

-

Only put roasted coffee beans in the bean hopper. If ground coffee,

instant coffee, raw coffee beans or any other substance is put in the

coffee bean hopper, it may cause damage to the machine.

-

Let the machine cool down before inserting or removing any parts. The

heating surfaces may retain residual heat after use.

-

Never fill the water tank with warm, hot or sparkling water, as this may

cause damage to the water tank and the machine.

-

Never use souring pads, abrasive cleaning agents or aggressive liquids

such as petrol or acetone to clean the machine. Simply use a soft cloth

dampened with water.

-

Descale your machine regularly. The machine indicates when descaling is

needed. Not doing this will make your appliance stop working properly.

In this case repair is not covered under your guarantee.

-

Do not keep the machine at temperatures below 0°C.Water left in the

heating system may freeze and cause damage.

-

Do not leave water in the water tank when the machine is not used over

a long period of time. The water can be contaminated. Use fresh water

every time you use the machine.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and

regulations regarding exposure to electromagnetic fields.

Machine overview (Fig. 1)

1 Control panel

2 Steam/ milk clean icon

3 Control dial

4 Coffee bean icons

5 Espresso button (Memo function)

6 Cappuccino button (Memo function)

7 Hot water icon

8 Descaling light

9 Warning light

10 2-cups/memo light

11 Water tank empty light

7

English

12 On/off button with light

13 Hot water/steam wand with protective handle

14 Water tank

15 Coffee dispensing spout

16 Automatic milk frother

17 Milk tube connector

18 Suction tube

19 Top of the milk carafe

20 Pin on top of the milk carafe

21 Milk carafe

22 Drip tray full indicator

23 Drip tray cover

24 Drip tray

25 Coffee grounds container

26 Brew group

27 Service door

28 Grinder adjustment knob

29 Ceramic coffee grinder

30 Coffee bean container

31 Grinding degree adjustment tool

32 Lid of coffee bean container

First installation

Installing the machine

1 Remove all packaging material from the machine.

2 Place the machine on a table or worktop away from the tap, the sink and

heat sources.

15cm

Note: Leave at least 15 cm of free space above, behind and on both sides

of the machine.

3 Insert the small plug into the socket located on the back of the machine.

4 Insert the plug into the wall socket.

8

English

5 Remove the protective sticker from the drip tray and slide the drip tray

into the guiding grooves in the front of the machine.

Note: Make sure the drip tray is fully inserted.

6 Insert the automatic milk frother.

Filling the water tank

1 Turn the automatic milk frother to the left.

2 Remove the water tank from the machine.

3 Rinse the water tank under the tap.

4 Fill the water tank with cold tap water up to the MAX indication.

5 Slide the water tank back into the machine.

9

English

Filling the coffee bean container

1 Fill the coffee bean container with espresso beans.

Note: Only use espresso beans. Never use ground coffee, unroasted

coffee beans or caramelised coffee beans, as this may cause damage to

the machine.

2 Put the lid on the coffee bean container.

Heating up the machine

During the initial heat-up process, fresh water flows through the internal

circuit to heat up the machine. This takes a few seconds.

1 Place a big cup under the hot water/steam wand and the coffee spout.

Make sure the control dial points to one of the coffee bean icons.

2 Press the on/off button.

3 When the warning light flashes quickly, turn the control dial to the hot

water icon and wait a few seconds.

-

The warning light goes out and some water comes out of the hot

water/steam wand or automatic milk frother.

4 After a few seconds, when hot water stops coming out of the hot

water/steam wand and the warning light flashes slowly, turn the control

dial back to the single bean icon.

-

The machine is heating up and the on/off button flashes slowly.

-

When the machine has heated up, it performs an automatic rinsing

cycle to clean the internal circuit with fresh water. Water flows from

the coffee spout.

-

When the on/off button lights up continuously, the machine is ready

for the manual rinsing cycle.

Note:You can stop the automatic rinsing cycle by pressing the espresso

or the cappuccino button.

Note:The automatic rinsing cycle also takes place 60 minutes after the

appliance switches to standby mode or switches off.

10

English

Installing the Intenza+ water filter

We advise you to install the Intenza+ water filter as this prevents scale

build-up in your machine. You can buy the Intenza+ water filter separately.

For more details, see chapter ‘Guarantee and support’, section ‘Ordering

maintenance products’.

1 Remove the small white filter from the water tank and store it in a dry

place.

Note: Please keep the small white filter for future use. You will need it for

the descaling process.

2 Remove the filter from its packaging and immerse it in cold water with the

opening pointing upwards. Press the sides of the filter gently to let out

the air bubbles.

3 Turn the knob of the filter to the setting that corresponds to the water

hardness of the area you live in.

a Very soft water/ soft water

b Hard water (default)

c Very hard water

Note: You can test the water hardness with a water hardness test strip.

4 Place the filter in the empty water tank. Press it down until it cannot

move any further.

5 Fill the water tank with fresh water up to the MAX indication and slide it

into the machine.

6 Let the machine brew hot water until the water tank is empty (see

chapter ‘Using the machine’, section ‘Hot water’).

7 Refill the water tank with fresh water up to the MAX indication and slide it

back into the machine.

-

The on/off button lights up continuously.

The machine is ready for use.

Using the machine

To guarantee perfect espresso, the machine regularly rinses its inner circuit

with water. This automatic rinsing cycle takes place 60 minutes after the

appliance switches to standby mode or switches off. During the automatic

11

English

rinsing cycle, some of the water flows through the inner circuit directly into

the drip tray. Empty the drip tray regularly.

Brewing 1 or 2 cups of espresso

1 Make sure the on/off button light lights up continuously and the control

dial points to the desired coffee strength bean icon.

2 Place 1 or 2 cups under the coffee spout.

3 Select the coffee strength by turning the dial to one or two beans. Select

2 beans for a stronger taste.

4 Press the espresso button.

Note:You can interrupt the brewing cycle at any time. Press the same

button that you pressed to start brewing coffee.

-

Press the espresso button once to brew 1 cup of coffee.

-

Press the espresso button twice to brew 2 cups of coffee.

-

When brewing 2 cups of coffee the 2-cup light lights up. The machine

grinds the required amount of coffee beans for one cup and then fills

both cups half. Then the machine grinds coffee beans for one cup

again and fills both cups fully.

Note:When the machine is left in standby mode, it switches off

automatically after 60 minutes.

Brewing milk- based beverages

Note: Use cold milk (at a temperature of approximately 5°C/41°F) with a

protein content of at least 3% to ensure an optimal frothing result. You can

use whole milk, semi-skimmed milk, soy milk and lactose free milk.

Brewing cappuccino

Warning: Danger of burning! Dispensing may be preceded by

small jets of hot water. When steam is used, the hot water/steam

wand and automatic milk frother could be hot. Only grab the

steam wand by its protective handle.

1 Attach the automatic milk frother to the hot water/steam wand.

12

English

2 Turn the hot water/steam wand with the automatic milk frother towards

the machine until the automatic milk frother touches the machine and is

in horizontal position.

3 Remove the lid of the milk carafe and pour the milk in the milk carafe.

Close the lid of the milk carafe.

4 Insert the other end of the suction tube into the milk carafe till the bottom

of the milk carafe.

5 Place a large cup under the automatic milk frother and the coffee spout.

6 Select the coffee strength by turning the dial to one or two beans. Select

2 beans for a stronger taste.

7 Press the cappuccino button. The machine dispenses first the milk and

then coffee.

-

It will take a few seconds before the machine stops dispensing.

Note: If you want to interrupt the brewing cycle press the cappuccino

button again.

8 The amount of coffee and milk can be customized, see chapter 'Adjusting

the machine', section 'Adjusting coffee and milk length'.

9 Place a cup under the automatic milk frother. Perform a quick clean

dispensing hot water for 3-5 seconds after brewing a cappuccino, see

chapter 'Cleaning and maintenance', section 'Quick Clean of the milk

system'.

10 Remove the milk tube connector from the automatic milk frother.

11 Plug the milk connector to the pin on the milk container lid and put the

milk container in the fridge.

Note: After dispensing a milk based beverage perform a quick clean of

the milk system by dispensing hot water for 5 seconds.

Frothing milk

Warning: Danger of burning! Dispensing may be preceded by

small jets of hot water. When steam is used, the hot water/steam

wand and automatic milk frother could be hot. Only grab the

steam wand by its protective handle.

1 Follow steps 1 to 5 from 'Brewing cappuccino' and turn the dial to the

steam/milk clean icon to froth milk.

13

English

2 Turn the control dial to one or two coffee beans icon to stop frothing

milk.

Hot water

Warning: Danger of scalding! Dispensing may be preceded by

small jets of hot water. Use the appropriate protective handle

only.

1 Make sure the on/off button lights up continuously. If the on/off button

flashes slowly, the machine is heating up.

2 Remove the automatic milk frother. Keep the protective handle on the

hot water/steam wand.

3 Place a cup under the hot water/steam wand.

4 Turn the control dial to the hot water icon.

-

Water comes out of the hot water/steam wand.

5 Turn the control dial back to one of the coffee bean icons when the cup

contains the preferred amount of hot water.

Adjusting the machine

You can adjust the grinding degree and coffee volume to obtain coffee that

is perfectly customised to your taste.

Adjusting the grinding degree

You can adjust the grinding degree of the machine.The ceramic coffee

grinder guarantees accurate and perfect grinding and coarseness for every

14

English

cup of coffee. It ensures full aroma preservation, delivering the perfect taste

in every cup.

2

1

-

Press the grinding degree adjustment knob firmly and then turn it one

notch at a time.

-

There are 5 different grinding degree settings you can choose from.The

smaller the dot, the stronger the coffee.

-

The difference becomes noticeable after you have brewed 2-3 cups f

coffee at the new setting.

Warning: Do not turn the grinding degree adjustment knob more

than one notch at a time to prevent damage to the grinder.

Adjusting the coffee volume with the MEMO function

You can adjust the coffee volume to your taste and the size of your cups.

The espresso button can be programmed.

1 Place one cup under the coffee dispensing spout.

2 Press and hold the espresso button. Release the button when the

machine starts to grind coffee beans.

-

The 2-cups light and the on/off button flash slowly.

3 Press the espresso button when the cup contains the desired amount of

coffee.

The machine automatically saves the new setting.

Adjusting the cappuccino volume with the MEMO function

You can adjust the coffee volume to your taste and the size of your cups.

The cappuccino button can be programmed.

1 Place a cup under the coffee dispensing spout.

2 Press and hold the cappuccino button. Release the button when the

machine starts to grind coffee beans.

-

The 2-cup light and the on/off button flash slowly.

3 Press the cappuccino button again when the cup contains the desired

amount of milk.

The machine automatically saves the new setting.

Cleaning and maintenance

Regular cleaning and descaling prolongs the lifetime of your machine and

ensures optimum quality and taste of your coffee.

Warning: Never use scouring pads, abrasive cleaning agents or

aggressive liquids to clean the machine.

Warning: Always unplug the machine and let it cool down before

you clean it.

Note: None of the detachable parts are dishwasher-proof. Rinse them under

the tap.

15

English

Quick clean of the milk system

Note: After brewing a cappuccino perform a quick clean of the milk system.

1 Place a cup under the automatic milk frother.

2 Turn the control dial to the hot water icon.

3 Dispense HOT WATER for 5 seconds

4 Turn the control dial to one of the coffee bean icons to stop hot water

dispensing.

Cleaning the automatic milk frother (daily)

1 Place a cup under the automatic milk frother.

2 Insert the suction tube into a cup filled with fresh water.

3 Turn the control dial to the steam/milk clean icon.

4 Dispense hot water for 5 seconds.

5 Turn the control dial to one of the coffee beans to stop hot water

dispensing.

Full milk carafe cleaning with milk circuit cleaner (monthly)

Monthly cleaning of the automatic milk frother

Monthly cleaning of the automatic milk frother consists of two cleaning

cycles carried out in sequence: the first cycle requires the use of Saeco milk

circuit cleaner dissolved in water and the second cycle uses only water to

rinse the circuit.

Caution: If the machine has been recently used, the steam tube and the

automatic milk frother could be hot.

Note: Before you start the procedure, make sure that the water tank is filled

up to the MAX level.

Cleaning cycle with milk circuit cleaner and water.

1 Pour the content of a Saeco milk circuit cleaner sachet into the milk

carafe and fill the milk carafe with water up to the MAX level. Close the

lid of the milk carafe.

2 Insert the other end of the suction tube into the milk carafe till the bottom

of the milk carafe.

3 Place a large container under the milk dispensing spout.

4 Turn the control dial to the steam/milk clean icon.

-

The machine dispenses the cleaning solution through the milk

dispensing spout.

5 Let the machine dispense water until the water tank empty light lights up.

6 Detach the suction tube from the machine. Rinse the milk carafe

thoroughly and fill it with fresh water up to the MAX level.

7 Repeat steps 3 to 6.

Cleaning the parts of the automatic milk frother

The automatic milk frother comprises four parts that must be disassembled:

16

English

1

2

4

5

3

1 Suction tube

2 Milk frother lid

3 Rubber ring

4 Milk frother

5 Rubber cover

How to clean the automatic milk frother

1 Remove the automatic milk frother from the steam tube.

Caution: If the machine has been recently used, the steam tube and the

automatic milk frother could be hot.

2 Remove the suction tube from the milk frother lid.

3 Remove the rubber ring from the automatic milk frother.

2

1

4 To detach the automatic milk frother, press the sides (1) and remove it by

pulling it out while making slight lateral movements (2).

5 Remove the rubber lid from the milk frother.

6 Rinse the components with lukewarm water.

Note: You can also clean these components in the dishwasher.

17

English

7 To reassemble, press in the middle to attach the rubber lid to the milk

frother and make sure it is in place.

8 Attach the automatic milk frother to the milk frother lid. When the two

parts lock into place, you hear a click.

9 Insert the suction tube into the automatic milk frother.

10 Place the rubber ring back onto the automatic milk frother.

11 Attach the automatic milk frother back to the hot water/steam wand.

18

English

Cleaning the brew group

Warning: Do not clean the brew group in the dishwasher and do

not use washing-up liquid or a cleaning agent to clean it.

Clean the brew group once a week.

1 Switch off the machine and unplug it.

2 Remove the coffee grounds container from the machine.

3 Open the service door.

1

2

4 Press the PUSH button and pull at the grip of the brew group to remove it

from the machine.

5 Clean the coffee exit duct thoroughly with a spoon handle or another

round-tipped kitchen utensil.

6 Clean the inside of the machine with a damp cloth.

19

English

7 Rinse the outside of the brew group under a lukewarm tap.

Warning: Never use any washing-up liquid or other cleaning

agent to clean the brewing unit.

Warning: Do not dry the brew group with a cloth to prevent fibers

from collecting inside the brewing unit.After rinsing, just shake

excess water off the brewing unit or let it air-dry.

8 Before you slide the brew group back into the machine, make sure the

two reference signs on the side match. If they do not match, perform the

following step:

-

Make sure the lever is in contact with the base of the brew group.

9 Make sure the locking hook of the brew group is in the correct position.

-

To position the hook correctly, push it upwards until it is in uppermost

position.

Note:The hook is not correctly positioned if it is still in bottommost

position.

20

English

ページが読み込まれています...

Philips HD8652/57 ユーザーマニュアル

Philips HD8652/57 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント