Not for
Reproduction
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
80084674
Revision: A
Not for
Reproduction
3
11
12
13
14
15
16
17
18
Not for
Reproduction
5
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA. All rights reserved.
This manual contains safety information to make you aware of the hazards and risks
associated with engines and how to avoid them. It also contains instructions for the
proper use and care of the engine. Because Briggs & Stratton Corporation does not
necessarily know what equipment this engine will power, it is important that you read
and understand these instructions and the instructions for the equipment.Save these
original instructions for future reference.
Note:The figures and illustrations in this manual are provided for reference only and
may differ from your specific model. Contact your dealer if you have questions.
For replacement parts or technical assistance, record below the engine model, type,
and code numbers along with the date of purchase. These numbers are located on your
engine (see theFeatures and Controlssection).
Date of Purchase
Engine Model - Type - Trim
Engine Serial Number
Recycling Information
Recycle all packaging, used oil, and batteries according to
applicable government regulations.
Operator Safety
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS for future use.
Safety Alert Symbol and Signal Words
The safety alert symbol ( ) is used to identify safety information about hazards that
can result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used
with the alert symbol to indicate the likelihood and the potential severity of injury. In
addition, a hazard symbol may be used to represent the type of hazard.
DANGERindicates a hazard which, if not avoided,will result in death or
serious injury.
WARNINGindicates a hazard which, if not avoided,could result in death or
serious injury.
CAUTIONindicates a hazard which, if not avoided,could result in minor or
moderate injury.
NOTICEindicates a situation thatcould result in damage to the product.
Hazard Symbols and Meanings
Safety information about
hazards that can result in
personal injury.
Read and understand the
Operator's Manual before
operating or servicing the
unit.
Fire hazard Explosion hazard
Shock hazard Toxic fume hazard
Hot surface hazard Noise hazard - Ear protection
recommended for extended
use.
Thrown object hazard -
Wear eye protection.
Explosion hazard
Frostbite hazard Kickback hazard
Amputation hazard -
moving parts
Chemical hazard
Thermal heat hazard Corrosive
Safety Messages
WARNING
Briggs & Stratton® Engines are not designed for and are not to be used to power:
fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);
motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not
sanctioned by Briggs & Stratton. For information about competitive racing products,
see www.briggsracing.com. For use with utility and side-by-side ATVs, please contact
Briggs & Stratton Power Application Center, 1-866-927-3349. Improper engine
application may result in serious injury or death.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Adding Fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
When Starting Engine
• Make sure that spark plug, muffler, fuel cap and air cleaner (if equipped) are in
place and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN / RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
When Operating Equipment
• Do not tip engine or equipment at angle which causes fuel to spill.
• Do not choke the carburetor to stop engine.
• Never start or run the engine with the air cleaner assembly (if equipped) or the air
filter (if equipped) removed.
When Changing Oil
• If you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel can
leak out and result in a fire or explosion.
When Tipping Unit for Maintenance
• When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
When Transporting Equipment
• Transport with fuel tank EMPTY or with fuel shut-off valve in the CLOSED
position.
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
Not for
Reproduction
6 BRIGGSandSTRATTON.com
WARNING
Starting engine creates sparking.
Sparking can ignite nearby flammable gases.
Explosion and fire could result.
• If there is natural or LP gas leakage in area, do not start engine.
• Do not use pressurized starting fluids because vapors are flammable.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed
to carbon monoxide gas. If you start to feel sick, dizzy, or weak while using
this product, get to fresh air RIGHT AWAY. See a doctor. You may have carbon
monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
WARNING
Rotating parts can contact or entangle hands, feet, hair, clothing, or
accessories.
Traumatic amputation or severe laceration can result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose-fitting clothing, dangling drawstrings or items that could become
caught.
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Models with portable battery pack:Remove battery pack from engine battery
tray. Battery pack may represent equipment key in some instances.
• Models with integrated battery pack:Disconnect wire harness from starter
motor.
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
WARNING
Improper use of the battery and charger can result in an electrical shock or
fire.
When Operating
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce the risk of electrical shock, do not allow water to flow into AC plug.
• Do not short circuit; never place any object into the battery contacts.
When Charging The Battery Pack
• Charge the Briggs and Stratton battery pack only with the Briggs and Stratton
battery charger.
• Do not use the Briggs and Stratton battery charger to charge any other types of
batteries.
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce risk of damage to the electric plug and cord, pull by the plug rather than
the cord when disconnecting the charger.
• Do not operate the charger with a damaged plug or cord. The supply cord cannot
be replaced. If the cord is damaged, the charger should be replaced immediately.
• Do not operate the charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. If the charger is damaged it must be replaced.
The charger is not serviceable.
• Do not disassemble or attempt to service the charger.
• To reduce risk of electric shock, unplug the charger from outlet before cleaning.
• Do not short circuit; never place any object into the battery contacts.
• The charger is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to make sure that they do not play with the
charger.
Extension Cord
• An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
1. That the pins on the plug of the extension cord are the same number, size,
and shape as those of the plug on the charger;
2. That the extension cord is properly wired and in good electrical condition;
and
3. That the wire size is a minimum of 16 AWG to allow for AC ampere rating of
the charger.
When Storing Battery Pack
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
Before Performing Adjustments Or Repairs
• Models with portable battery pack:Remove the battery pack from the engine
battery tray.
• Models with integrated battery pack:Disconnect the wire harness from the
starter motor.
Not for
Reproduction
7
WARNING
Battery chemicals are toxic and corrosive.
Fire or explosion can cause severe burns or death.
• Never burn or incinerate discarded or used battery packs as they may explode.
Toxic fumes and materials are created when battery packs are burned.
• Do not use a battery that has been crushed, dropped, or damaged.
Features and Controls
Engine Controls
Compare the illustration (Figure:1,2,3) with your engine to familiarize yourself with the
location of various features and controls.
A. Engine Identification NumbersModel - Type - Code
B. Spark Plug
C. Muffler, Muffler Guard (if equipped), Spark Arrester (if equipped)
D. Electric Starter
E. Dipstick
F. Lithium-Ion Portable Battery Pack
G. Air Intake Grille
H. Fuel Tank and Cap
I. Air Cleaner
J. Throttle Control (if equipped)
K. Battery Charger - Portable Battery Pack
L. Fuel Shut-off (if equipped)
M. Lithium-Ion Integrated Battery Pack
N. Cable and Charger - Integrated Battery Pack
Engine Control Symbols and Meanings
Engine speed - FAST Engine speed - SLOW
Engine speed - STOP ON - OFF
Engine start - Choke
CLOSED
Engine start - Choke OPEN
Fuel Cap
Fuel Shut-off - OPEN
Fuel Shut-off - CLOSED
Fuel level - Maximum
Do not overfill
Battery Control Symbols and Meanings
Volt Ampere
Double Insulated Alternating Current
Direct Current Underwriters Laboratories,
Inc. US & Canada Listed
Product
Underwriters Laboratories,
Inc. Registered Product
Hertz
Properly Recycle Battery
Charge Battery Pack
Remove Key / Battery Pack
Operation
Oil Recommendations
Oil Capacity:See theSpecificationssection.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil as specified by the instructions in
this manual. If you start the engine without oil, it will be damaged beyond repair and
will not be covered under warranty.
We recommend the use of Briggs & Stratton
®
Warranty Certified oils for best
performance. Other high-quality detergent oils are permitted if classified for service SF,
SG, SH, SJ or higher. Do not use special additives.
Outdoor temperatures determine the correct oil viscosity for the engine. Use the chart
to select the best viscosity for the outdoor temperature range expected. Engines on
most outdoor power equipment operate well with 5W-30 Synthetic oil. For equipment
operated in hot temperatures, Vanguard
®
15W-50 Synthetic oil gives the best
protection.
A SAE 30 -Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.
B 10W-30 -Above 80 °F (27 °C) the use of 10W-30 may cause increased oil
consumption. Checkthe oil level frequently.
C 5W-30
D Synthetic 5W-30
Not for
Reproduction
8 BRIGGSandSTRATTON.com
E
Vanguard
®
Synthetic 15W-50
Check and Add Oil
See Figure: 4
Before checking or adding oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
NOTICE
This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers
or dealers may have added oil to the engine. Before you start the engine for the first
time, make sure to check the oil level and add oil according to the instructions in this
manual. If you start the engine without oil, it will be damaged beyond repair and will
not be covered under warranty.
Check Oil Level
1. Remove the dipstick (A, Figure 4) and wipe with a clean cloth.
2. Install and tighten the dipstick (A, Figure 4).
3. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 4) on the dipstick.
Add Oil
1. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 4). Do not
overfill. After adding oil, wait one minute and then check the oil level.
2. Reinstall and tighten the dipstick (A, Figure 4).
Fuel Recommendations
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.
• Gasoline with up to 10% ethanol (gasohol) is acceptable.
NOTICE Do not use unapproved gasolines, such as E15 and E85. Do not mix oil in
gasoline or modify the engine to run on alternate fuels. Use of unapproved fuels will
damage the engine components, which will not be covered under warranty.
To protect the fuel system from gum formation, mix a fuel stabilizer into the fuel.
SeeStorage.All fuel is not the same. If starting or performance problems occur,
change fuel providers or change brands. This engine is certified to operate on gasoline.
The emissions control system for this engine is EM (Engine Modifications).
High Altitude
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)
gasoline is acceptable.
For carbureted engines, high altitude adjustment is required to maintain performance.
Operation without this adjustment will cause decreased performance, increased fuel
consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service
Dealer for high altitude adjustment information. Operation of the engine at altitudes
below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.
For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.
Add Fuel
See Figure: 5
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When adding fuel
• Turn engine off and let engine cool at least 2 minutes before removing the fuel
cap.
• Fill fuel tank outdoors or in well-ventilated area.
• Do not overfill fuel tank. To allow for expansion of the fuel, do not fill above the
bottom of the fuel tank neck.
• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition
sources.
• Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
necessary.
• If fuel spills, wait until it evaporates before starting engine.
1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.
2. Fill the fuel tank (A, Figure 5) with fuel. To allow for expansion of the fuel, do not
fill above the bottom of the fuel tank neck (B). Some models have a fuel level
indicator (C). Do not fill the tank above the bottom of the fuel level indicator (D).
3. Reinstall the fuel cap.
Charge The Battery Pack
See Figure :6789
WARNING
Improper use of the battery or the charger can result in an electrical shock or
fire.
When Charging Battery Pack
• Charge the Briggs & Stratton battery pack only with the Briggs & Stratton battery
charger.
• Do not use the Briggs & Stratton battery charger to charge any other types of
batteries.
• Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
• To reduce risk of damage to the electric plug and cord, pull by the plug rather than
the cord when disconnecting the charger.
• An extension cord should not be used unless absolutely necessary. Use of
improper extension cord could result in a risk of fire and electric shock. If an
extension cord must be used, make sure:
1. That the pins on the plug of the extension cord are the same number, size,
and shape as those of the plug on the charger;
2. That the extension cord is properly wired and in good electrical condition;
and
3. That the wire size is a minimum of 16 AWG to allow for AC ampere rating of
the charger.
• Do not operate the charger with a damaged plug or cord. The supply cord cannot
be replaced. If the cord is damaged, the charger should be replaced immediately.
• Do not operate the charger if it has received a sharp blow, been dropped, or
otherwise damaged in any way. If the charger is damaged it must be replaced.
The charger is not serviceable.
• Do not disassemble the charger; or attempt to service.
• To reduce risk of electric shock, unplug the charger from outlet before cleaning.
• Do not short circuit; never place any object into the battery contacts.
• The charger is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be supervised to make sure that they do not play with the
charger.
When To Charge The Battery Pack
First Time Portable Battery Pack- The Lithium‐Ion portable battery pack was partially
charged before shipment. To maintain charge and to prevent damage while in storage,
the battery pack is programed to enter a “sleep mode”. A quick charge of approximately
ten (10) seconds is required to wake up the battery. Leave battery pack in charger
until fully charged. To charge the battery pack, see theHow To Charge The Battery
Packsection below.
As Required- To check available charge, push the Battery Fuel Gauge button (E,
Figure67) and charge if required. See theBattery Fuel Gaugesection.
How To Charge The Battery Pack
WARNING
Keep the battery charger dry. Avoid exposing the battery pack to rain or wet
conditions.
1. Connect the battery charger (F, Figure89) to an electrical outlet.
2. Portable Battery Pack:Slide the battery pack (G, Figure8) firmly into the battery
charging bay (F). If the red charging light does not illuminate, remove the battery
pack and reinstall. Make sure the battery pack is firmly seated in the battery
charging bay.
• Red light (A, Figure6) indicates the battery pack is charging normally.
• Green light (B) indicates the battery pack is fully charged.
• Red light (C) flashes indicates that the battery pack is either too hot or
too cold and will not accept a charge. Leave the battery pack connected
and when normal operating temperature is reached it will automatically
start charging. See theSpecificationssection for normal operating
temperature.
Not for
Reproduction
9
• Red/green lights (D) flashes indicate that the battery pack will not charge
and must be replaced.
3. Portable Battery Pack:From “sleep mode”, the battery will wake up in
approximately ten (10) seconds.
4. Portable Battery Pack:A completely discharged battery pack will fully charge in
approximately one (1) hour. The battery pack will stay fully charged if left on the
charger.
5. Portable Battery Pack:When the green light indicates that the battery pack is
fully charged, remove the battery pack from the charger.
6. Integrated Battery Pack:Connect the charger plug (G, Figure9) to the engine.
7. Integrated Battery Pack:A completely discharged battery pack will fully charge in
approximately four (4) hours.
8. Integrated Battery Pack:When the green light indicates that the battery pack is
fully charged, remove from the charger.
9. To check available charge, push the Battery Fuel Gauge button (E, Figure67).
10. When not in use, disconnect the battery charger from the electrical outlet.
Battery Fuel Gauge
To check available charge, push the Battery Fuel Gauge button (E, Figure67). The
display lights (H) will indicate the approximate amount of available charge remaining in
the battery pack.
Display Lights Available Charge
Four lights 75% to 100%
Three lights 50% to 75%
Two lights 25% to 50%
One light 10% to 25%
Light flashes Low
Integrated Battery Pack:When connected to the charger, if all display lights are off
then the battery is fully charged. Disconnect the charger.
Start and Stop Engine
See Figure:10,11,12,13
Start Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Starting Engine
• Make surethat spark plug, muffler, fuel cap and air cleaner (if equipped) are in
place and secured.
• Do not crank engine with spark plug removed.
• If engine floods, set choke (if equipped) to OPEN or RUN position, move throttle (if
equipped) to FAST position and crank until engine starts.
WARNING
Improper use of battery and charger can result in an electrical shock or fire.
When Operating
• Keep battery charger dry. Avoid exposing battery pack to rain or wet conditions.
• To reduce the risk of electrical shock, do not allow water to flow into AC plug.
• Do not short circuit; never place any object into the battery contacts.
WARNING
POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a
poisonous gas that could kill you in minutes. You CANNOT see it, smell it, or
taste it. Even if you do not smell exhaust fumes, you could still be exposed to
carbon monoxide gas. If you start to feel sick, dizzy, or weak while using this
product, shut it off and get to fresh air RIGHT AWAY. See a doctor. You may
have carbon monoxide poisoning.
• Operate this product ONLY outside far away from windows, doors and vents to
reduce the risk of carbon monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide
alarms with battery back-up according to the manufacturer's instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages, basements, crawlspaces,
sheds, or other partially-enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly build up in these spaces
and can linger for hours, even after this product has shut off.
• ALWAYS place this product downwind and point the engine exhaust away from
occupied spaces.
NOTICE This engine was shipped from Briggs & Stratton without oil. Before you
start the engine, make sure you add oil according to the instructions in this manual.
If you start the engine without oil, it will be damaged beyond repair and will not be
covered under warranty.
Note:Equipment may have remote controls. See the equipment manual for location and
operation of remote controls.
1. Check the engine oil. See theCheck Oil Levelsection.
2. Modelswithportable battery pack:Mount the battery pack (A, Figure10) in
the engine battery tray on top of the engine. Make sure battery pack is securely
installed. Battery pack may represent equipment key in some instances.
Note:Modelswithportable battery pack:To wake up a new battery, aFirst
Timequick charge of approximately ten (10) seconds is required. See theWhen To
Charge Battery Packsection.
3. Make sure equipment drive controls, if equipped, are disengaged.
4. Move the fuel shut-off (D, Figure11), if equipped, to the OPEN position.
5. Move the throttle control (B, Figure11), if equipped, to the FAST position. Operate
the engine in the FAST position.
6. Modelswithelectric start switch:Hold the engine stop lever (C, Figure12)
against the handle. Move the electric start switch to the START position. See the
equipment manual for the location and operation of the electric start switch.
7. Modelswithoutelectric start switch:Hold the engine stop lever (C, Figure12)
against the handle. Engine will automatically start. See the equipment manual for
operation of the engine stop lever.
NOTICE To extend the life of the starter, use short starting cycles (five seconds
maximum). Wait one minute between starting cycles.
Modelswithportable battery pack:If the engine will not crank and the battery pack
display lights are flashing, then the battery pack temperature is too hot or current draw is
too high. All four battery display lights (H, Figure13) will flash a warning for 10 seconds.
The battery pack does not have a fuse, but will automatically reset after 10 seconds. If
battery pack temperature is too hot (over 140 F, 60 C), remove the battery and allow it
to cool. To avoid excess current draw on lawnmowers, keep the mower housing clean of
grass build-up and debris.
Note:If the engine does not start after repeated attempts, contact a local dealer or go
toBRIGGSandSTRATTON.comor call1-800-233-3723(in USA).
Stop Engine
1. Engine Stop Lever:Release the engine stop lever (E, Figure12).
Throttle Control, if equipped with stop feature:Move the throttle control (B,
Figure11) to the STOP position.
Electric Start Switch, if equipped:Move the electric start switch to the OFF /
STOP position. See the equipment manual for the location and operation of the
switch. Remove the key and keep in a safe place out of the reach of children.
2. After the engine stops, move the fuel shut-off (D, Figure11), if equipped, to the
CLOSED position.
3. Modelswithportable battery pack:Remove the battery pack. The battery pack
may represent equipment key in some instances.
Maintenance
NOTICE If the engine is tipped during maintenance, the fuel tank, if mounted on
engine, must be empty and the spark plug side must be up. If the fuel tank is not
empty and if the engine is tipped in any other direction, it may be difficult to start due
to oil or gasoline contaminating the air filter and/or the spark plug.
WARNING
When performing maintenance that requires the unit to be tipped, the fuel tank, if
mounted on the engine, must be empty or fuel can leak out and result in a fire or
explosion.
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
Not for
Reproduction
10 BRIGGSandSTRATTON.com
NOTICE All the components used to build this engine must remain in place for
proper operation.
WARNING
Unintentional sparking can result in fire or electric shock.
Unintentional start-up can result in entanglement, traumatic amputation, or
laceration.
Fire hazard
Before performing adjustments or repairs:
• Disconnect the spark plug wire and keep it away from the spark plug.
• Models with portable battery pack:Remove the battery pack from the engine
battery tray. The battery pack may represent equipment key in some instances.
• Models with integrated battery pack:Disconnect the wire harness from the
starter motor.
• Use only correct tools.
• Do not tamper with governor spring, links or other parts to increase engine speed.
• Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit,
and may result in injury.
• Do not strike the flywheel with a hammer or hard object because the flywheel may
later shatter during operation.
When testing for spark:
• Use approved spark plug tester.
• Do not check for spark with spark plug removed.
Emissions Control Service
Maintenance, replacement, or repair of the emissions control devices and
systems may be performed by any off-road engine repair establishment or
individual. However, to obtain "no charge" emissions control service, the work must be
performed by a factory authorized dealer. See the Emissions Control Statements.
Maintenance Schedule
First 5 Hours
• Change oil (Not required on Just Check & Add™ models)
Every 8 Hours or Daily
• Check engine oil level
• Clean area around muffler and controls
• Clean air intake grille
Every 25 Hours or Annually
•
Clean air filter
1
• Clean pre-cleaner (if equipped)
Every 50 Hours or Annually
• Change engine oil (Not required on Just Check & Add™ models)
• Service exhaust system
Annually
• Replace spark plug
• Replace air filter
• Replace pre-cleaner (if equipped)
•
Service cooling system
1
•
Check valve clearance
2
1
In dusty conditions or when airborne debris is present, clean more often.
2
Not required unless engine performance problems are noted.
Carburetor and Engine Speed
Never make adjustments to the carburetor or engine speed. The carburetor was set at
the factory to operate efficiently under most conditions. Do not tamper with the governor
spring, linkages, or other parts to change the engine speed. If any adjustments are
required contact a Briggs & Stratton Authorized Service Dealer for service.
NOTICE The equipment manufacturer specifies the maximum speed for the engine
as installed on the equipment.Do not exceedthis speed. If you are not sure what the
equipment maximum speed is, or what the engine speed is set to from the factory,
contact a Briggs & Stratton Authorized Service Dealer for assistance. For safe and
proper operation of the equipment, the engine speed should be adjusted only by a
qualified service technician.
Service Spark Plug
See Figure:14
Check the gap (A, Figure14) with a wire gauge (B). If necessary, reset the gap. Install
and tighten the spark plug to the recommended torque. For gap setting or torque, see
theSpecificationssection.
Note:In some areas, local law requires using a resistor spark plug to suppress ignition
signals. If this engine was originally equipped with a resistor spark plug, use the same
type for replacement.
Service Exhaust System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
• It is a violation of California Public Resource Code, Section 4442, to use or
operate the engine on any forest-covered, brush-covered, or grass-covered land
unless the exhaust system is equipped with a spark arrester, as defined in Section
4442, maintained in effective working order. Other states or federal jurisdictions
may have similar laws. Contact the original equipment manufacturer, retailer, or
dealer to obtain a spark arrester designed for the exhaust system installed on this
engine.
Remove accumulated debris from muffler and cylinder area. Inspect the muffler for
cracks, corrosion, or other damage. Remove the deflector or the spark arrester, if
equipped, and inspect for damage or carbon blockage. If damage is found, install
replacement parts before operating.
WARNING
Replacement parts must be of the same design and installed in the same position
as the original parts. Other parts may not perform as well, may damage the unit, and
may result in injury.
Change Engine Oil
See Figure:15,16,17,18
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
• When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion.
• Allow muffler, engine cylinder and fins to cool before touching.
Check and add oil as required. See theCheck Oil Levelsection. An oil change is not
required but if you desire to change the oil follow the procedure below.
Used oil is a hazardous waste product and must be disposed of properly. Do not discard
with household waste. Check with your local authorities, service center, or dealer for
safe disposal/recycling facilities.
Remove Oil
The oil must be drained from the top oil fill tube.
1. With engine off but still warm, disconnect the spark plug wire (D, Figure15) and
keep it away from the spark plug (E).
Not for
Reproduction
11
2. Models with integrated battery:Disconnect the wire harness (F, Figure16) from
the electric starter.
3. Remove the dipstick (A, Figure17).
4. When you drain the oil from the top oil fill tube (C, Figure18), keep the spark plug
(E) end of the engine up. Drain the oil into an approved container.
WARNING
When you drain the oil from the top oil fill tube, the fuel tank must be empty or fuel
can leak out and result in a fire or explosion. To empty the fuel tank, run the engine
until it stops from lack of fuel.
Add Oil
• Make sure the engine is level.
• Clean the oil fill area of any debris.
• See the Specifications section for oil capacity.
1. Remove the dipstick (A, Figure 17) and wipe with a clean cloth.
2. Slowly pour oil into the engine oil fill (C, Figure 17). Do not overfill. After adding
oil, wait one minute and then check the oil level.
3. Install and tighten the dipstick (A, Figure 17).
4. Remove the dipstick and check the oil level. Correct oil level is at the top of the full
indicator (B, Figure 17) on the dipstick.
5. Reinstall and tighten the dipstick (A, Figure 17).
6. Connect the spark plug wire (D, Figure 15) to the spark plug (E).
Service Air Filter
See Figure: 19
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
• Never start and run the engine with the air cleaner assembly (if equipped) or the
air filter (if equipped) removed.
NOTICE Do not use pressurized air or solvents to clean the filter. Pressurized air
can damage the filter and solvents will dissolve the filter.
See the Maintenance Schedule for service requirements.
Paper Air Filter
1. Open the cover (B, Figure 19).
2. Remove the filter (C, Figure 19).
3. Remove the pre-cleaner (E, Figure 19), if equipped, from the filter. To loosen
debris, gently tap the filter on a hard surface. If the filter is excessively dirty,
replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air
dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner, if equipped, to the filter.
6. Install the filter (C, Figure 19).
7. Close the cover (B, Figure 19).
Service Cooling System
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc., can catch fire.
• Allow muffler, engine cylinder and fins to cool before touching.
• Remove accumulated debris from muffler area and cylinder area.
NOTICE Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
1. Use a brush or dry cloth to remove debris from the air intake grille.
2. Keep linkage, springs and controls clean.
3. Keep the area around and behind the muffler, if equipped, free of any combustible
debris.
4. Make sure the oil cooler fins, if equipped, are free of dirt and debris.
After a period of time, debris can accumulate in the cylinder cooling fins and cause the
engine to overheat. This debris cannot be removed without partial disassembly of the
engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the air
cooling system as recommended in the Maintenance Schedule.
Lithium-Ion Battery Pack Disposal
WARNING
Battery chemicals are toxic and corrosive.
Fire or explosion can cause severe burns or death.
Electrical Shock
• Never burn or incinerate discarded or used battery packs as they may explode.
Toxic fumes and materials are created when battery packs are burned.
• Do not use a battery that has been crushed, dropped, or damaged.
Used and discarded battery packs will likely still carry a small electrical charge and
should be handled with care. Always dispose of discarded or used battery packs
according to federal, state and local regulations.
RBRC (Rechargeable Battery Recycling Corporation) Seal
RBRC is a non-profit public service organization dedicated to recycling
used rechargeable batteries. To find a battery collection site near
you, call toll free 1-800-8-BATTERY or 1-877-2-RECYCLE. For more
information and a listing of Recycling Locations, visit RBRC online at
www.call2recycle.org.
Storage
WARNING
Fuel and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Electrical Shock
When Storing Fuel Or Equipment With Fuel In Tank
• Store away from furnaces, stoves, water heaters or other appliances that have
pilot lights or other ignition sources because they can ignite fuel vapors.
When Storing Battery Pack
• Keep battery charger dry. Avoid exposing battery pack to rain or wet conditions.
Fuel System
See Figure:20,21
Note:Some models have a fuel tank for vertical storage that will let the engine tilt for
maintenance or storage (C, Figure20). Do not store in vertical position with fuel tank
filled above the bottom of the fuel level indicator (D), if equipped. For further instructions,
see the equipment manual.
Store the engine level (normal operating position). Fill fuel tank (A, Figure21) with fuel.
To allow for expansion of fuel, do not overfill above the fuel tank neck (B).
Fuel can become stale when kept in a storage container for more than 30 days. Each
time you fill the container with fuel, addfuel stabilizerto the fuel as specified by the
manufacturer’s instructions. This keeps fuel fresh and decreases fuel-related problems
or contamination in the fuel system.
It is not necessary to drain fuel from the engine whenfuel stabilizeris added as
instructed. Before storage, turn the engine ON for 2 minutes to move the fuel and
stabilizer through the fuel system.
Engine Oil
While the engine is still warm, change the engine oil. See the Change Oil section. For
Just Check & Add™ models, an oil change is not required.
Battery Pack and Charger
See Figure:2223
Portable battery pack:When not in use, disconnect charger and store in a cool, dry
area. Wet, damp areas can cause corrosion of terminals and electrical contacts. If stored
for long periods in high temperatures (120° F / 49° C), permanent damage to the battery
Not for
Reproduction
12 BRIGGSandSTRATTON.com
pack can result. Check electrical terminals and contacts on battery packs and charger.
Wipe with clean cloth or blow clean with compressed air.
After storage, a normal charge may be required. To check available charge, press the
Battery Fuel Gauge button (E, Figure2223) and charge if required. See theBattery
Fuel Gaugesection.
Troubleshooting
For assistance, contact your local dealer or go to BRIGGSandSTRATTON.com or call
1-800-233-3723 (in USA).
Specifications
Model:090000
Displacement 8.64ci (140cc)
Bore 2.495in (63,4mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .020in (,51mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Model:093J00
Displacement 9.15ci (150cc)
Bore 2.583in (65,60mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .020in (,51mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Model:100000
Displacement 9.93ci (163cc)
Bore 2.668in (68,28mm)
Stroke 1.75in (44,45mm)
Oil Capacity 15oz (,44L)
Spark Plug Gap .030in (,76mm)
Spark Plug Torque 180lb-in (20Nm)
Armature Air Gap .006 - .014in (,15 - ,36mm)
Intake Valve Clearance .004 - .008in (,10 - ,20mm)
Exhaust Valve Clearance .004 - .008in (,10 - ,20mm)
Lithium-Ion Battery (Portable)
Lithium-Ion Battery Pack 10.8V (10,8V)
Charge Minutes 60
Charging Current 2AMP (2AMP)
Charger AC Input (Variable) 100 - 240V
Operating Temperature 32 - 113° F (0 - 45° C)
Lithium-Ion Battery (Integrated)
Lithium-Ion Battery Pack 10.8V (10,8V)
Charge Minutes 240
Charging Current .5AMP (.5AMP)
Charger AC Input (Variable) 100 - 240V
Operating Temperature 32 - 104° F (0 - 44° C)
Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily
at an angle up to 15°. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Service Parts - Models:090000,093J00,100000
Service Part Part Number
Air Filter (see Figure19) 593260
Air Filter, Pre-cleaner (see Figure19) 594055
Oil - SAE 30 100005
Resistor Spark Plug (Model090000,093J00) 692051
Resistor Spark Plug (Model100000) 594056
Spark Plug Wrench 19576
Spark Tester 19368
Portable Lithium-Ion Battery Pack (US / Canada) 593559
Portable Lithium-Ion Battery Pack (EU / UK / AU) 593560
Portable Lithium-Ion Battery Charger (US / Canada) 593561
Portable Lithium-Ion Battery Charger (EU) 593562
Portable Lithium-Ion Battery Charger (UK) 593576
Portable Lithium-Ion Battery Charger (AU) 594501
Integrated Lithium-Ion Battery Pack 84002154
IntegratedLithium-Ion Battery Charger(US / Canada) 84002790
IntegratedLithium-Ion Battery Charger(UK) 84002791
IntegratedLithium-Ion Battery Charger(EU) 84002792
IntegratedLithium-Ion Battery Charger(AU) 84002793
We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts.
Power Ratings:The gross power rating for individual gasoline engine models is
labeled in accordance with SAE (Society of Automotive Engineers) code J1940 Small
Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995.
Torque values are derived at 2600 RPM for those engines with “rpm” called out on the
label and 3060 RPM for all others; horsepower values are derived at 3600 RPM. The
gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power
values are taken with exhaust and air cleaner installed whereas gross power values
are collected without these attachments. Actual gross engine power will be higher than
net engine power and is affected by, among other things, ambient operating conditions
and engine-to-engine variability. Given the wide array of products on which engines
are placed, the gasoline engine may not develop the rated gross power when used in a
given piece of power equipment. This difference is due to a variety of factors including,
but not limited to, the variety of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions
(temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing
and capacity limitations, Briggs & Stratton may substitute an engine of higher rated
power for this engine.
Warranty
Briggs & Stratton Engine Warranty
Effective January 2019
Limited Warranty
Briggs & Stratton warrants that, during the warranty period specified below, it will repair
or replace, free of charge, any part that is defective in material or workmanship or
both. Transportation charges on product submitted for repair or replacement under this
warranty must be borne by purchaser. This warranty is effective for and is subject to
the time periods and conditions stated below. For warranty service, find the nearest
Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.COM.
The purchaser must contact the Authorized Service Dealer, and then make the product
available to the Authorized Service Dealer for inspection and testing.
There is no other express warranty. Implied warranties, including those of
merchantability and fitness for a particular purpose, are limited to the warranty
period listed below, or to the extent permitted by law.Liability for incidental or
consequential damages are excluded to the extent exclusion is permitted by law. Some
states or countries do not allow limitations on how long an implied warranty lasts,
and some states or countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state and country to country
4
.
Not for
Reproduction
13
Standard Warranty Terms
1, 2, 3
Vanguard®; Commercial Series
3
Consumer Use - 36 months
Commercial Use - 36 months
XR Series
Consumer Use - 24 months
Commercial Use - 24 months
All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve
Consumer Use - 24 months
Commercial Use - 12 months
All Other Engines
Consumer Use - 24 months
Commercial Use - 3 months
1
These are our standard warranty terms, but occasionally there may
be additional warranty coverage that was not determined at time of
publication. For a listing of current warranty terms for your engine, go to
BRIGGSandSTRATTON.com or contact your Briggs & Stratton Authorized Service
Dealer.
2
There is no warranty for engines on equipment used for prime power in place
of a utility; standby generators used for commercial purposes, utility vehicles
exceeding 25 MPH, or engines used in competitive racing or on commercial or
rental tracks.
3
Vanguard installed on standby generators: 24 months consumer use, no
warranty commercial use. Commercial Series with manufacturing date before July
2017: 24 months consumer use, 24 months commercial use.
4
In Australia - Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
For warranty service, find the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by
emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, Moorebank, NSW , Australia, 2170.
The warranty period begins on the original date of purchase by the first retail or
commercial consumer. "Consumer use" means personal residential household use by a
retail consumer. "Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once an engine has experienced commercial
use, it shall thereafter be considered as a commercial use engine for purposes of this
warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial
purchase date at the time warranty service is requested, the manufacturing date
of the product will be used to determine the warranty period. Product registration
is not required to obtain warranty service on Briggs & Stratton products.
About Your Warranty
This limited warranty covers engine-related material and/or workmanship issues only,
and not replacement or refund of the equipment to which the engine may be mounted.
Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered
under this warranty. Similarly, warranty is not applicable if the engine has been altered
or modified or if the engine serial number has been defaced or removed. This warranty
does not cover engine damage or performance problems caused by:
1. The use of parts that are not original Briggs & Stratton parts;
2. Operating the engine with insufficient, contaminated, or an incorrect grade of
lubricating oil;
3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater
than 10%, or the use of alternative fuels such as liquefied petroleum or natural gas
on engines not originally designed/manufactured by Briggs & Stratton to operate
on such fuels;
4. Dirt which entered the engine because of improper air cleaner maintenance or re-
assembly;
5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly
installed blade adapters, impellers, or other crankshaft coupled devices, or
excessive v-belt tightness;
6. Associated parts or assemblies such as clutches, transmissions, equipment
controls, etc., which are not supplied by Briggs & Stratton;
7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or
clog the cooling fins or flywheel area, or by operating the engine without sufficient
ventilation;
8. Excessive vibration due to over-speeding, loose engine mounting, loose or
unbalanced cutter blades or impellers, or improper coupling of equipment
components to the crankshaft;
9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of
equipment, or improper engine installation.
Warranty service is available only through Briggs & Stratton Authorized Service
Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map
at BRIGGSandSTRATTON.COM or by calling 1-800-233-3723 (in USA).
80004537 (Rev. F)
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "B" or "G" Trim Designation (Model-
Type-Trim Representation xxxxxx xxxx Bx or xxxxxx xxxx Gx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust emissions (“emissions”) control system warranty on
your 2019-2021 engine. In California, new small off-road engines and large spark
ignited engines less than or equal to 1.0 liter must be designed, built, and equipped
to meet the State’s stringent anti-smog standards. B&S must warrant the emissions
control system on your engine for the periods of time listed below provided there has
been no abuse, neglect or improper maintenance of your small off-road engine or
equipment leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust emissions control system on your engine is warranted for two years.
If any emissions-related part on your engine is defective, the part will be repaired or
replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine owner, you are responsible for the performance of the required
maintenance listed in your owner’s manual. B&S recommends that you retain
all receipts covering maintenance on your engine, but B&S cannot deny
warranty coverage solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
• As the engine owner, you should however be aware that B&S may deny you
warranty coverage if your engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
• You are responsible for presenting your engine to a B&S distribution center
or service center as soon as the problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days. If you have a
question regarding your warranty rights and responsibilities, you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
b. Air Induction System
• Air cleaner
• Intake manifold
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
Not for
Reproduction
14 BRIGGSandSTRATTON.com
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in allmaterial respects to the
engine described in the manufacturer’s application for certification. The warranty
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operators’s Manual supplied, is warranted for the
period of time prior to the first scheduled replacement point for that part.
If the part fails prior to the first scheduled replacement, the part will be
repaired or replaced by B&S at no charge to the owner. Any such part
repaired or replaced under warranty will be warranted for the remainder of
the period prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084161_A
Briggs & Stratton Emissions Warranty
California, U.S. EPA, and Briggs & Stratton Corporation Emissions Control
Warranty - Your Warranty Rights and Obligations
For Briggs & Stratton Engine Models with "F" Trim Designation (Model-Type-
Trim Representation xxxxxx xxxx Fx)
The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S) are
pleased to explain the exhaust and evaporative emissions (“emissions”) control system
warranty on your 2019-2021 engine/equipment. In California, new equipment that
use small off-road engines must be designed, built, and equipped to meet the State’s
stringent anti-smog standards. B&S must warrant the emissions control system on
your engine/equipment for the periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your small off-road engine or equipment
leading to the failure of the emissions control system.
Your emissions control system may include parts such as the carburetor or fuel-
injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid
fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated
components. Also included may be hoses, belts, connectors, and other emission-
related assemblies.
Where a warrantable condition exists, B&S will repair your engine/equipment at no cost
to you including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage:
The exhaust and evaporative emissions control system on your engine/equipment is
warranted for two years. If any emissions-related part on your engine/equipment is
defective, the part will be repaired or replaced by B&S.
Owner’s Warranty Responsibilities:
• As the engine/equipment owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. B&S recommends that you
retain all receipts covering maintenance on your engine/equipment, but B&S
cannot deny warranty coverage solely for the lack of receipts or for your failure to
ensure the performance of all scheduled maintenance.
• As the engine/equipment owner, you should however be aware that B&S may
deny you warranty coverage if your engine/equipment or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
• You are responsible for presenting your engine/equipment to a B&S distribution
center or service center as soon as the problem exists. The warranty repairs shall
be completed in a reasonable amount of time, not to exceed 30 days. If you have
a question regarding your warranty rights and responsibilities you should contact
B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.COM.
Briggs & Stratton Emissions Control Warranty Provisions
The following are specific provisions relative to your Emissions Control Warranty
Coverage. It is in addition to the B&S engine warranty for non-regulated engines found
in the Operator’s Manual.
1. Warranted Emissions Parts
Coverage under this warranty extends only to the parts listed below (the
emissions control systems parts) to the extent these parts were present on the
B&S engine and/or B&S supplied fuel system.
a. Fuel Metering System
• Cold start enrichment system (soft choke)
• Carburetor or fuel injection system
• Oxygen sensor
• Electronic control unit
• Fuel pump module
• Fuel line (for liquid fuel and fuel vapors), fuel line fittings, clamps
• Fuel tank, cap and tether
• Carbon canister and mounting bracket
• Pressure relief valves
• Liquid/Vapor separator
b. Air Induction System
Not for
Reproduction
15
• Air cleaner
• Intake manifold
• Purge and vent line
c. Ignition System
• Spark plug(s)
• Magneto ignition system
d. Catalyst System
• Catalytic converter
• Exhaust manifold
• Air injection system or pulse value
e. Miscellaneous Items Used in Above Systems
• Vacuum, temperature, position, time sensitive valves and switches
• Connectors and assemblies
• Electronic controls
2. Length of Coverage
Coverage is for a period of two years from the date of delivery to an ultimate
purchaser, or for the time period listed in the respective engine or product
warranty statement, whichever is greater. B&S warrants to the original purchaser
and each subsequent purchaser that the engine is designed, built, and equipped
so as to conform with all applicable regulations adopted by the Air Resources
Board; that it is free from defects in material and workmanship that could cause
the failure of a warranted part; and that it is identical in all material respects to the
engine described in the manufacturer’s application for certification. The warranty
period begins on the date the engine or equipment is delivered to an ultimate
purchaser.
The warranty on emissions-related parts is as follows:
• Any warranted part that is not scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the
warranty period stated above. If any such part fails during the period of
warranty coverage, the part will be repaired or replaced by B&S at no
charge to the owner. Any such part repaired or replaced under the warranty
will be warranted for the remaining warranty period.
• Any warranted part that is scheduled only for regular inspection in the
Operator’s Manual supplied, is warranted for the warranty period stated
above. Any such part repaired or replaced under warranty will be warranted
for the remaining warranty period.
• Any warranted part that is scheduled for replacement as required
maintenance in the Operator’s Manual supplied, is warranted for the period
of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired
or replaced by B&S at no charge to the owner. Any such part repaired or
replaced under warranty will be warranted for the remainder of the period
prior to the first scheduled replacement point for the part.
• Add-on or modified parts that are not exempted by the Air Resources
Board may not be used. The use of any non-exempted add-on or modified
parts by the owner will be grounds for disallowing a warranty claim. The
manufacturer will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
3. Consequential Coverage
Coverage shall extend to the failure of any engine components caused by the
failure of any warranted emissions parts.
4. Claims and Coverage Exclusions
Warranty claims shall be filed according to the provisions of the B&S engine
warranty policy. Warranty coverage does not apply to failures of emissions
parts that are not original equipment B&S parts or to parts that fail due to abuse,
neglect, or improper maintenance as set forth in the B&S engine warranty policy.
B&S is not liable for warranty coverage of failures of emissions parts caused by
the use of add-on or modified parts.
Look For Relevant Emissions Durability Period and Air Index Information On
Your Small Off-Road Engine Emissions Label
Engines that are certified to meet the California Air Resources Board (CARB) small off-
road Emissions Standard must display information regarding the Emissions Durability
Period and the Air Index. Briggs & Stratton makes this information available to the
consumer on our emissions labels. The engine emissions label will indicate certification
information.
TheEmissions Durability Perioddescribes the number of hours of actual running
time for which the engine is certified to be emissions compliant, assuming proper
maintenance in accordance with the Operator’s Manual. The following categories are
used:
Moderate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
50 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 125 hours of actual engine running time.
Intermediate:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
125 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 250 hours of actual engine running time.
Extended:
Engines at or less than 80 cc displacement are certified to be emissions compliant for
300 hours of actual engine running time. Engines greater than 80 cc displacement are
certified to be emissions compliant for 500 hours of actual engine running time.
For example, a typical walk-behind lawn mower is used 20 to 25 hours per year.
Therefore, theEmissions Durability Periodof an engine with anintermediaterating
would equate to 10 to 12 years.
Briggs & Stratton engines are certified to meet the United States Environmental
Protection Agency (USEPA) Phase 2 or Phase 3 emissions standards. The Emissions
Compliance Period referred to on the Emissions Compliance label indicates the
number of operating hours for which the engine has been shown to meet Federal
emissions requirements.
For engines at or less than 80 cc displacement:
Category C = 50 hours, Category B = 125 hours, Category A = 300 hours
For engines greater than 80 cc displacement and less than 225 cc displacement:
Category C = 125 hours, Category B = 250 hours, Category A = 500 hours
For engines of 225 cc or more displacement:
Category C = 250 hours, Category B = 500 hours, Category A = 1000 hours
80084158_A
Not for
Reproduction
16 BRIGGSandSTRATTON.com
Hak Cipta Perusahaan Briggs & Stratton, Milwaukee, WI, USA. Hak Cipta dilindungi
Undang-Undang.
Panduan ini berisi informasi keselamatan yang membuat Anda mengetahui bahaya dan
risiko yang berkaitan dengan mesin dan cara menghindarinya. Panduan ini juga berisi
petunjuk tentang cara penggunaan dan perawatan mesin yang tepat. Mengingat Briggs
& Stratton Corporation tidak selalu mengetahui peralatan apa yang akandigerakkan
oleh mesin ini, penting kiranya bahwa Anda membaca serta memahami petunjuk ini
dan petunjuk untuk peralatan tersebut. Simpan petunjuk asli ini untuk rujukan masa
depan.
Perhatikan:Angka-angka dan ilustrasi dalam panduan ini disediakan hanya sebagai
referensi dan mungkin saja berbeda dari model yang Anda miliki. Hubungi dealer Anda
jika Anda memiliki pertanyaan.
Untuk meminta suku cadang pengganti atau bantuan teknis, catat model, tipe, dan
nomor kode mesin beserta tanggal pembeliannya. Nomor-nomor ini terletak di mesin
Anda (lihat bagian Fitur dan Kontrol).
Tanggal Pembelian
Model - Tipe - Trim Mesin
Nomor Seri Mesin
Informasi Daur Ulang
Semua kemasan, oli bekas, dan baterai harus didaur ulang
sesuai aturan pemerintah yang berlaku.
Keselamatan Operator
PETUNJUK PENTING KESELEMATAN
SIMPAN PETUNJUK INI untuk digunakan di masa mendatang.
Simbol Peringatan dan Kata Sinyal
Keselamatan
Simbol peringatan keselamatan ( ) digunakan untuk mengidentifikasi informasi
keselamatan tentang bahaya yang dapat menyebabkan cedera pribadi. Kata sinyal
(BAHAYA, PERINGATAN, atau PERHATIAN) digunakan dengan simbol peringatan
untuk mengindikasikan kemungkinan dan potensi keparahan cedera. Selain itu, simbol
bahaya dapat digunakan untuk menunjukkan jenis bahaya.
BAHAYA menunjukkan bahaya yang, jika tidak dihindari, akan menyebabkan
kematian atau cedera serius.
PERINGATAN menunjukkan bahaya yang, jika tidak dihindari, dapat
menyebabkan kematian atau cedera serius.
PERHATIAN menunjukkan bahaya yang, jika tidak dihindari, dapat
menyebabkan cedera ringan atau sedang.
PEMBERITAHUAN menunjukkan situasi yang dapat menyebabkan kerusakan pada
produk.
Simbol Keselamatan dan Artinya
Informasi keselamatan
mengenai bahaya yang
dapat mengakibatkan
cedera diri.
Baca dan pahami Panduan
Operator sebelum
mengoperasikan atau
menyervis unit.
Bahaya kebakaran Bahaya ledakan
Bahaya sengatan listrik Bahaya asap beracun
Bahaya permukaan panas Bahaya kebisingan
- Pelindung telinga
direkomendasikan untuk
penggunaan jangka panjang.
Bahaya benda terlempar -
Kenakan pelindung mata.
Bahaya ledakan
Bahaya radang beku Bahaya hentakan balik
Bahaya amputasi -
komponen yang bergerak
Bahaya bahan kimia
Bahaya panas termal Korosif
Pesan Keselamatan
PERINGATAN
Mesin Briggs & Stratton® tidak dirancang untuk dan tidak akan digunakan untuk
menggerakkan: fun-kart; go-kart; kendaraan serba guna (all-terrain vehicle - ATV)
untuk rekreasi, atau olah raga anak; sepeda motor; hovercraft; produk pesawat;
atau kendaraan yang digunakan pada acara pertandingan yang tidak disetujui
oleh Briggs & Stratton. Untuk informasi tentang produk balap kompetitif, lihat
www.briggsracing.com. Untuk penggunaan dengan utilitas dan ATV samping, silakan
hubungi Briggs & Stratton Engine Application Center, 1-866-927-3349. Penerapan
mesin yang tidak tepat dapat mengakibatkan cedera serius atau kematian.
PERINGATAN
Bahan bakar dan uapnya sangat mudah terbakar dan meledak.
Kebakaran atau ledakan dapat menyebabkan luka bakar yang parah atau
kematian.
Saat Menambahkan Bahan Bakar
• Matikan mesin dan biarkan menjadi dingin selama 2 menit sebelum melepas tutup
bahan bakar.
• Lakukan pengisian tangki bahan bakar di luar ruangan atau di area berventilasi
baik.
• Jangan isi tangki secara berlebihan. Agar bahan bakar dapat menyebar di dalam
tangki, jangan lakukan pengisian di atas bagian dasar leher tangki bahan bakar.
• Jauhkan bahan bakar dari percikan api, nyala api, lampu penunjuk, panas, dan
sumber pemicu api lainnya.
• Periksa saluran bahan bakar, tangki, tutup tangki, dan pengepas secara rutin
untuk melihat apakah ada keretakan atau kebocoran. Ganti jika perlu.
• Jika bahan bakar tumpah, tunggu hingga tumpahannya menguap sebelum
menstarter mesin.
Saat Menyalakan Mesin
• Pastikan bahwa busi, knalpot, tutup tangki, dan pembersih udara (jika ada) berada
pada tempatnya dan terpasang dengan erat.
• Jangan menghidupkan mesin saat busi dilepas.
• Jika mesin mengalami banjir, setel cuk (jika dilengkapi) ke posisi OPEN / RUN,
pindahkan trotel (jika dilengkapi) ke posisi FAST lalu putar sampai mesin menyala.
Saat Mengoperasikan Peralatan
• Jangan miringkan mesin atau peralatan, sehingga menyebabkan bahan bakar
tumpah.
• Jangan menggunakan cuk karburator untuk menghentikan mesin.
• Jangan starter atau operasikan mesin dengan pembersih udara yang terpasang
(jika dilengkapi) atau filter udara (jika dilengkapi) yang dilepas.
Saat Mengganti Oli
• Jika Anda menguras oli dari tabung pengisian oli atas, tangki bahan bakar harus
kosong, karena bila tidak, bahan bakar bisa bocor keluar dan menimbulkan
kebakaran atau ledakan.
Not for
Reproduction
17
Saat Memiringkan Unit untuk Perawatan
• Saat melakukan perawatan yang mengharuskan agar unit dimiringkan, tangki
bahan bakar, jika terpasang pada mesin, harus kosong karena bila tidak, bahan
bakar bisa bocor keluar dan mengakibatkan kebakaran atau ledakan.
Saat Memindahkan Peralatan
• Angkut dengan tangki bahan bakar KOSONG atau katup penutup bahan bakar
pada posisi TERTUTUP.
Saat Menyimpan Bahan Bakar Atau Peralatan Dengan Bahan Bakar di Tangki
• Jauhkan peralatan dari tungku, kompor, alat pemanas air, atau perangkat lainnya
yang dilengkapi lampu utama maupun sumber penyalaan lainnya karena dapat
menyulut uap bahan bakar.
PERINGATAN
Menstarter mesin akan menghasilkan bunga api.
Bunga api dapat menyulut gas yang mudah terbakar di dekatnya.
Ledakan dan kebakaran dapat terjadi.
• Jika terdapat kebocoran gas alam atau LP di suatu area, jangan menstarter
mesin.
• Jangan menggunakan cairan starter bertekanan karena uapnya mudah terbakar.
PERINGATAN
BAHAYA GAS BERACUN. Gas pembuangan mesin mengandung karbon
monoksida, yakni gas beracun yang dapat mematikan dalam hitungan menit.
Anda TIDAK DAPAT melihatnya, menciumnya, atau merasakannya. Meskipun
Anda tidak mencium asap gas buang, Anda masih bisa terpapar gas karbon
monoksida. Jika Anda mulai merasa tidak enak badan, pusing, atau lemas saat
menggunakan produk ini, matikan dan SEGERA cari udara segar. Kunjungi
dokter. Anda mungkin keracunan karbon monoksida.
• Operasikan produk ini HANYA jika berada di luar ruangan, jauh dari jendela, pintu,
dan ventilasi untuk mengurangi risiko akumulasi gas karbon monoksida yang
berpotensi masuk ke dalam ruang hunian manusia.
• Pasanglah alarm karbon monoksida bertenaga baterai atau sambungkan alarm
karbon monoksida ke stopkontak listrik dengan baterai cadangan berdasarkan
petunjuk produsen. Alarm asap tidak dapat mendeteksi gas karbon monoksida.
• JANGAN mengoperasikan produk ini di dalam rumah, garasi, ruang bawah tanah,
kolong, gudang, atau ruang yang tertutup sebagian lainnya, bahkan dengan kipas
angin atau pintu dan jendela yang terbuka sebagai ventilasi. Karbon monoksida
dapat terkumpul dengan cepat di berbagai tempat tersebut dan bertahan selama
berjam-jam, bahkan setelah produk ini dimatikan.
• SELALU letakkan produk ini sesuai arah angin dan posisikan saluran gas buang
mesin menjauh dari tempat hunian manusia.
PERINGATAN
Suku cadang yang berputar dapat mengenai atau menarik tangan, kaki, rambut,
pakaian, atau aksesori.
Amputasi traumatik atau laserasi berat dapat terjadi.
• Operasikan peralatan dengan pelindung terpasang di tempatnya.
• Jauhkan tangan dan kaki dari suku cadang yang berputar.
• Ikat rambut yang panjang dan lepas perhiasan.
• Jangan mengenakan pakaian yang longgar , tali celana yang menggantung, atau
benda yang dapat tersangkut.
PERINGATAN
Mesin yang aktif menghasilkan panas. Bagian mesin, terutama knalpot,
mengalami peningkatan suhu yang drastis.
Menyentuhnya akan menyebabkan luka bakar parah .
Serpihan yang mudah terbakar, seperti daun, rumput, sikat, dll. dapat tersulut
api.
• Biarkan knalpot, silinder mesin, dan sirip mendingin sebelum menyentuhnya.
• Bersihkan tumpukan kotoran dari bagian knalpot dan bagian silinder.
• Merupakan pelanggaran California Public Resource Code, Pasal 4442, jika
menggunakan atau mengoperasikan mesin di lahan yang tertutup hutan, tertutup
semak, atau tertutup rumput kecuali sistem pembuangannya dilengkapi dengan
pelindung percikan (spark arrester), sebagaimana disebutkan dalam Pasal
4442, yang dirawat dan dapat bekerja dengan baik. Yurisdiksi federal atau
negara bagian lainnya mungkin memiliki undang-undang yang serupa. Hubungi
produsen peralatan asli, peritel, atau dealer untuk memperoleh spark arrester
yang dirancang untuk sistem pembuangan yang dipasang pada mesin ini.
PERINGATAN
Memantik bunga api secara tidak sengaja dapat menyebabkan kebakaran atau
sengatan listrik.
Penstarteran yang terjadi secara tidak disengaja dapat mengakibatkan belitan,
amputasi traumatik, atau laserasi.
Bahaya kebakaran
Sebelum melakukan penyesuaian atau perbaikan:
• Lepas kabel busi dan jauhkan dari busi.
• Model-model dengan baterai portabel:Lepaskan baterai dari nampan baterai
mesin. Baterai dapat mewakili kunci peralatan dalam beberapa contoh.
• Model-model dengan baterai terintegrasi:Putuskan harnes kabel dari motor
starter.
• Gunakan hanya alat yang tepat.
• Jangan utak-atik pegas governor, persambungan, atau komponen lainnya untuk
menambah kecepatan mesin.
• Komponen pengganti harus sama dan dipasang pada posisi yang sama seperti
komponen asli. Komponen lain juga mungkin tidak akan berfungsi dengan baik,
bisa merusak unit, dan dapat mengakibatkan cedera.
• Jangan membenturkan roda gila dengan palu atau benda yang keras karena roda
gila bisa pecah selama pengoperasian berlangsung.
Saat menguji cetusan listrik:
• Gunakan penguji busi yang disetujui.
• Jangan periksa cetusan listrik saat busi dilepas.
PERINGATAN
Penggunaan yang tidak benar dari baterai dan pengisi daya bisa
mengakibatkan sengatan listrik atau kebakaran.
Saat Mengoperasikan
• Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan perangkat baterai
terhadap hujan atau kondisi basah.
• Untuk mengurangi risiko sengatan listrik, jangan biarkan air mengalir menuju
stopkontak AC.
• Jangan ada hubungan pendek/korsleting; jangan letakkan benda apa pun
bersinggungan dengan baterai.
Saat Mengisi Daya Baterai
• Isi daya baterai Briggs & Stratton hanya dengan menggunakan pengisi daya
baterai Briggs & Stratton.
• Jangan gunakan pengisi daya baterai Briggs & Stratton untuk mengisi daya
baterai tipe lain.
• Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan perangkat baterai
terhadap hujan atau kondisi basah.
• Untuk mengurangi kerusakan steker dan kabel listrik, tarik steker bukannya kabel
ketika melepas sambungan pengisi daya.
• Jangan mengoperasikan pengisi daya dengan steker atau kabel yang rusak.
Kabel yang tersedia tidak dapat diganti. Jika kabel rusak, pengisi daya harus
segera diganti.
• Jangan mengoperasikan pengisi daya jika telah terkena benda tajam, jatuh, atau
rusak dengan cara apa pun. Jika rusak, pengisi daya harus diganti. Pengisi daya
tidak dapat diperbaiki.
• Jangan membongkar atau berusaha memperbaiki pengisi daya.
• Untuk mengurangi risiko sengatan listrik, cabut pengisi daya dari stopkontak
sebelum membersihkan.
• Jangan ada hubungan pendek/korsleting; jangan letakkan benda apa pun
bersinggungan dengan baterai.
• Pengisi daya tidak dimaksudkan untuk digunakan oleh seseorang (termasuk
anak-anak) dengan kemampuan fisik, inderawi, atau mental yang lemah, atau
kurangnya pengalaman dan pengetahuan, kecuali mereka berada dalam
pengawasan atau diberi petunjuk sehubungan dengan penggunaan alat oleh
seseorang yang bertanggung jawab atas keamanan mereka.
• Anak-anak harus diawasi untuk memastikan bahwa mereka tidak bermain dengan
pengisi daya tersebut.
Kabel Sambungan
Not for
Reproduction
18 BRIGGSandSTRATTON.com
• Kabel sambungan tidak boleh digunakan kecuali sangat diperlukan. Penggunaan
kabel sambungan yang tidak benar bisa mengakibatkan risiko kebakaran dan
sengatan listrik. Jika kabel sambungan harus digunakan, pastikan:
1. Pin pada steker kabel sambungan mempunyai nomor, ukuran, dan bentuk
yang sama dengan steker pada pengisi daya;
2. Kabel sambungan terikat dengan baik dan dalam kondisi listrik yang baik;
dan
3. Ukuran kabel minimum 16 AWG untuk memungkinkan nilai AC ampere
pengisi daya.
Saat Menyimpan Baterai
• Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan perangkat baterai
terhadap hujan atau kondisi basah.
Sebelum Melakukan Penyesuaian Atau Perbaikan:
• Model-model dengan baterai portabel:Lepaskan baterai dari nampan baterai
mesin.
• Model-model dengan baterai terintegrasi:Putuskan harnes kabel dari motor
starter.
PERINGATAN
Bahan kimia baterai bersifat racun dan korosif.
Kebakaran atau ledakan dapat menyebabkan luka bakar yang parah atau
kematian.
• Jangan menghanguskan atau membakar baterai yang telah dilepas atau
digunakan karena dapat meledak. Asap dan bahan beracun muncul saat baterai
terbakar.
• Jangan gunakan baterai yang telah dihancurkan, dijatuhkan, atau rusak.
Fitur dan Kontrol
Kontrol Mesin
Bandingkan Ilustrasi (Gambar:1,2,3) dengan mesin Anda agar mengenali lokasi
beragam fitur dan kontrol.
A. Nomor Identifikasi MesinModel - Tipe - Kode
B. Busi
C. Knalpot, Pelindung Knalpot (jika ada), Penahan Percikan Api (jika ada)
D. Starter Elektrik
E. Stik Pengukur Oli
F. Perangkat Baterai Portabel Ion-Litium
G. Kisi-kisi Saluran Masuk Udara
H. Tangki Bahan Bakar dan Tutup Tangki
I. Pembersih Udara
J. Kontrol Trotel (jika ada)
K. Pengisi Daya Baterai - Perangkat Baterai Portabel
L. Penutup Bahan Bakar (jika ada)
M. Perangkat Baterai Terintegrasi Ion-Litium
N. Kabel dan Pengisi Daya - Perangkat Baterai Terintegrasi
Simbol Kontrol Mesin dan Artinya
Kecepatan mesin -
CEPAT
Kecepatan mesin - LAMBAT
Kecepatan mesin -
BERHENTI
NYALA - MATI
Mesin start - Cuk TUTUP Mesin start - Cuk BUKA
Tutup Bahan Bakar
Penutup Bahan Bakar -
BUKA
Penutup Bahan Bakar -
TUTUP
Level bahan bakar -
Maksimum
Jangan mengisi terlalu
penuh
Simbol Kontrol Baterai dan Artinya
Volt Ampere
Terinsulasi Ganda Arus Bolak-Balik
Arus Searah Underwriters Laboratories,
Inc. Produk Terdaftar AS &
Kanada
Underwriters Laboratories,
Inc. Produk Terdaftar
Hertz
Daur Ulang Baterai
Sebaik-baiknya
Mengisi Daya Baterai
Lepas Kunci / Perangkat
Baterai
Pengoperasian
Rekomendasi Oli
Kapasitas Oli: Lihat bagian Spesifikasi.
PEMBERITAHUAN
Mesin ini dikirim dari Briggs & Stratton tanpa oli. Pabrik peralatan atau dealer
mungkin telah menambahkan oli pada mesin. Sebelum menstarter mesin untuk
pertama kali, pastikan Anda memeriksa level oli dan menambahkan oli sesuai dengan
petunjuk dalam panduan ini. Apabila Anda menstarter mesin tanpa oli, mesin akan
mengalami kerusakan permanen dan tidak akan ditanggung garansi.
Kami menyarankan Anda agar menggunakan Oli Resmi Bergaransi Briggs & Stratton
®
untuk mendapatkan performa terbaik. Oli detergen berkualitas tinggi lainnya dapat
digunakan jika tergolong untuk servis SF, SG, SH, SJ atau yang lebih tinggi. Jangan
gunakan bahan aditif khusus.
Suhu luar ruangan menentukan viskositas oli yang benar untuk mesin. Gunakan
bagan berikut untuk memilih viskositas terbaik untuk perkiraan kisaran suhu luar
ruangan. Mesin pada peralatan daya luar ruangan cocok dengan Oli Sintetis 5W-30.
Not for
Reproduction
19
Untuk peralatan yang dioperasikan pada suhu panas, Oli Sintetis Vanguard
®
15W-50
memberikan perlindungan yang terbaik.
A SAE 30 - Pada suhu di bawah 40°F (4°C), penggunaan oli SAE 30 akan
mengakibatkan penstarteran yang sulit.
B 10W-30 - Pada suhu di atas 80°F (27°C) penggunaan oli 10W-30 dapat
menyebabkan bertambahnya konsumsi oli. Periksa level oli secara lebih
sering.
C 5W-30
D Sintetis 5W-30
E
Sintetis 15W-50 Vanguard
®
Cek dan Tambah Oli
Lihat Gambar: 4
Sebelum memeriksa atau menambah oli
• Pastikan mesin dalam posisi datar.
• Bersihkan bagian lubang pengisian oli dari serpihan.
• Bacalah bagian Spesifikasi untuk mengetahui kapasitas oli.
PEMBERITAHUAN
Mesin ini dikirim dari Briggs & Stratton tanpa oli. Pabrik peralatan atau dealer
mungkin telah menambahkan oli pada mesin. Sebelum menstarter mesin untuk
pertama kali, pastikan Anda memeriksa level oli dan menambahkan oli sesuai dengan
petunjuk dalam panduan ini. Jika Anda menstarter mesin tanpa oli, mesin akan rusak
secara permanen dan tidak akan ditanggung oleh garansi.
Periksa Level Oli
1. Lepaskan batang celup (A, Gambar 4) dan seka dengan kain bersih.
2. Pasang dan kencangkan batang celup (A, Gambar 4).
3. Lepaskan batang celup dan periksa level oli. Level oli yang baik adalah berada di
bagian atas dari indikator penuh (B, Gambar 4) pada batang celup.
Tambahkan Oli
1. Jika level oli rendah, tuangkan oli perlahan-lahan ke dalam lubang pengisian
oli pada mesin (C, Gambar 4). Jangan mengisi terlalu penuh. Setelah
menambahkan oli, tunggu selama satu menit dan kemudian periksa kembali level
oli.
2. Pasang kembali dan kencangkan stik pengukur oli (A, Gambar 4).
Rekomendasi Bahan Bakar
Bahan bakar harus memenuhi persyaratan ini:
• Bensin yang bersih, segar, dan tanpa timbal.
• Oktan minimum 87/87 AKI (91 RON). Penggunaan di tempat tinggi, lihat di bawah.
• Bensin dengan kandungan hingga 10% etanol (gasohol) dapat diterima.
PEMBERITAHUAN Jangan gunakan bensin yang tidak disetujui, seperti E15 dan
E85. Jangan mencampurkan oli ke dalam bensin atau memodifikasi mesin untuk
berjalan dengan bahan bakar lain. Penggunaan bahan bakar yang tidak disetujui
akan merusak komponen mesin, yang tidak akan ditanggung dalam garansi.
Untuk melindungi sistem bahan bakar dari pembentukan ampas, campurkan stabilisator
bahan bakar ke dalam bahan bakar. Lihat Penyimpanan. Tidak semua bahan bakar
sama. Jika mesin sulit dihidupkan atau performanya buruk, ganti penyedia bahan bakar
atau ganti merek bahan bakar. Mesin ini disertifikasi untuk beroperasi menggunakan
bensin. Sistem kontrol emisi untuk mesin ini adalah EM (Engine Modifications
[Modifikasi Mesin]).
Ketinggian tinggi
Di ketinggian lebih dari 5000 kaki (1524 meter), bahan bakar minyak minimal
85oktan/85 AKI (89 RON) dapat diterima.
Untuk mesin karburator, pengaturan ketinggian diperlukan untuk menjaga kinerja
kerja. Aktivitas tanpa pengaturan ketinggian dapat menyebabkan kinerja kerja
menurun, peningkatan konsumsi bahan bakar, dan peningkatan emisi/gas buang.
Hubungi Distributor Resmi Briggs & Stratton untuk informasi tentang pengaturan
ketinggian. Aktivitas mesin di bawah ketinggian 2500 kaki (762 meter) tidak dianjurkan
menggunakan pengaturan ketinggian.
Untuk mesin yang menggunakan Injeksi Bahan Bakar Elektronik (IBBE) tidak
memerlukan pengaturan ketinggian.
Tambahkan Bahan Bakar
Lihat Gambar: 5
PERINGATAN
Bahan bakar serta uapnya sangat mudah terbakar dan meledak.
Kebakaran atau ledakan dapat menyebabkan luka bakar yang parah atau
kematian.
Saat menambahkan bahan bakar
• Matikan mesin dan biarkan menjadi dingin selama 2 menit sebelum melepas tutup
bahan bakar.
• Lakukan pengisian tangki bahan bakar di luar ruangan atau di area berventilasi
baik.
• Jangan isi tangki secara berlebihan. Agar bahan bakar dapat menyebar di dalam
tangki, jangan lakukan pengisian di atas bagian dasar leher tangki bahan bakar.
• Jauhkan bahan bakar dari percikan api, nyala api, lampu penunjuk, panas, dan
sumber pemicu api lainnya.
• Periksa saluran bahan bakar, tangki, tutup tangki, dan pengepas secara rutin
untuk melihat apakah ada keretakan atau kebocoran. Ganti jika perlu.
• Jika bahan bakar tumpah, tunggu hingga tumpahannya menguap sebelum
menstarter mesin.
1. Bersihkan bagian lubang pengisian oli dari kotoran dan serpihan. Lepas tutup
bahan bakar.
2. Isi tangki bahan bakar (A, Gambar 5) dengan bahan bakar. Agar bahan bakar
dapat menyebar di dalam tangki, jangan lakukan pengisian di atas bagian dasar
leher tangki bahan bakar. Beberapa model memiliki indikator ketinggian bahan
bakar (C). Jangan isi tangki hingga di atas bagian dasar indikator ketinggian
bahan bakar (D).
3. Pasang kembali tutup tangki.
Mengisi Daya Baterai
Lihat Gambar :6789
PERINGATAN
Penggunaan yang tidak benar dari baterai atau pengisi daya bisa
mengakibatkan sengatan listrik atau kebakaran.
Saat Mengisi Daya Perangkat Baterai
• Isi daya baterai Briggs & Stratton hanya dengan menggunakan pengisi daya
baterai Briggs & Stratton.
• Jangan gunakan pengisi daya baterai Briggs & Stratton untuk mengisi daya
baterai tipe lain.
• Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan perangkat baterai
terhadap hujan atau kondisi basah.
• Untuk mengurangi kerusakan steker dan kabel listrik, tarik steker bukannya kabel
ketika melepas sambungan pengisi daya.
• Kabel sambungan tidak boleh digunakan kecuali sangat diperlukan. Penggunaan
kabel sambungan yang tidak benar bisa mengakibatkan risiko kebakaran dan
sengatan listrik. Jika kabel sambungan harus digunakan, pastikan:
1. Pin pada steker kabel sambungan mempunyai nomor, ukuran, dan bentuk
yang sama dengan steker pada pengisi daya;
2. Kabel sambungan terikat dengan baik dan dalam kondisi listrik yang baik;
dan
3. Ukuran kabel minimum 16 AWG untuk memungkinkan nilai AC ampere
pengisi daya.
• Jangan mengoperasikan pengisi daya dengan steker atau kabel yang rusak.
Kabel yang tersedia tidak dapat diganti. Jika kabel rusak, pengisi daya harus
segera diganti.
Not for
Reproduction
20 BRIGGSandSTRATTON.com
• Jangan mengoperasikan pengisi daya jika telah terkena benda tajam, jatuh, atau
rusak dengan cara apa pun. Jika rusak, pengisi daya harus diganti. Pengisi daya
tidak dapat diperbaiki.
• Jangan membongkar pengisi daya, atau berusaha memperbaikinya.
• Untuk mengurangi risiko sengatan listrik, cabut pengisi daya dari stopkontak
sebelum membersihkan.
• Jangan ada hubungan pendek/korsleting; jangan letakkan benda apa pun
bersinggungan dengan baterai.
• Pengisi daya tidak dimaksudkan untuk digunakan oleh seseorang (termasuk
anak-anak) dengan kemampuan fisik, inderawi, atau mental yang lemah, atau
kurangnya pengalaman dan pengetahuan, kecuali mereka berada dalam
pengawasan atau diberi petunjuk sehubungan dengan penggunaan alat oleh
seseorang yang bertanggung jawab atas keamanan mereka.
• Anak-anak harus diawasi untuk memastikan bahwa mereka tidak bermain dengan
pengisi daya tersebut.
Kapan Mengisi Daya Perangkat Baterai
Perangkat Baterai Portabel Kali Pertama- Perangkat Baterai Ion-Litium terisi daya
sebagian sebelum pengiriman. Untuk mempertahankan isi daya dan mencegah
kerusakan saat ada dalam penyimpanan, perangkat baterai diprogram supaya ada
dalam “mode tidur”. Pengisian daya singkat sekitar sepuluh (10) detik diperlukan
untuk membangunkan baterai. Biarkan perangkat baterai terisi daya sampai penuh.
Untuk mengisi daya perangkat baterai, lihat bagianCara Mengisi Daya Perangkat
Bateraiberikut ini.
Sebagaimana Dipersyaratkan- Untuk memeriksa isi daya yang tersedia, tekan
tombol ukuran Bahan Bakar Baterai (E, Gambar67) dan isi daya bila perlu. Lihat
bagianUkuran Bahan Bakar Baterai.
Cara Mengisi Daya Perangkat Baterai
PERINGATAN
Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan perangkat baterai
terhadap hujan atau kondisi basah.
1. Sambungkan pengisi daya baterai (F, Gambar89) ke stopkontak listrik.
2. Perangkat Baterai Portabel:Geser perangkat baterai (G, Gambar8) dengan
kuat ke arah bagian dalam pengisi daya baterai (F). Jika lampu pengisi daya
merah tidak menyala, lepas perangkat baterai dan pasang kembali. Pastikan
perangkat baterai terpasang dengan kuat pada bagian dalam pengisi daya
baterai.
• Lampu merah (A, Gambar6) menandakan bahwa perangkat baterai terisi
daya dengan normal.
• Lampu hijau (B) menandakan bahwa perangkat baterai sudah penuh.
• Lampu merah (C) berkedip menandakan bahwa perangkat baterai terlalu
panas atau terlalu dingin dan tidak akan menerima pengisian daya. Biarkan
perangkat baterai tetap tersambung dan ketika suhu pengoperasian normal
tercapai akan otomatis mulai mengisi daya. Lihat bagianSpesifikasiuntuk
suhu pengoperasian normal.
• Lampu merah/hijau (D) berkedip menandakan bahwa baterai tidak dapat
diisi daya dan harus diganti.
3. Perangkat Baterai Portabel:Dari “mode tidur”, baterai akan bangun dalam waktu
sekitar sepuluh (10) detik.
4. Perangkat Baterai Portabel:Baterai yang kosong sama sekali akan terisi daya
penuh dalam waktu sekitar satu (1) jam. Perangkat baterai akan tetap terisi daya
jika dibiarkan pada pengisi daya.
5. Perangkat Baterai Portabel:Apabila lampu hijau menunjukkan bahwa daya
perangkat baterai terisi penuh, lepas perangkat baterai dari pengisi daya.
6. Perangkat Baterai Terintegrasi:Hubungkan kepala pengisi daya (G, Gambar9)
dengan mesin.
7. Perangkat Baterai Terintegrasi:Baterai yang kosong sama sekali akan terisi
daya penuh dalam waktu sekitar empat (4) jam.
8. Perangkat Baterai Terintegrasi:Ketika terhubung ke pengisi daya, jika semua
lampu tampilan mati, maka daya baterai telah terisi penuh. Lepaskan pengisi
daya.
9. Untuk memeriksa isi daya yang tersedia, tekan tombol Ukuran Bahan Bakar
Baterai (E, Gambar67).
10. Ketika tidak digunakan, lepaskan pengisi daya baterai dari stopkontak listrik.
bagian Ukuran Bahan Bakar
Untuk memeriksa isi daya yang tersedia, tekan tombol Ukuran Bahan Bakar Baterai (E,
Gambar67). Lampu tampilan (H) akan menandakan bahwa perkiraan jumlah isi daya
yang tersisa dalam perangkat baterai.
Lampu Tampilan Isi Daya yang Tersedia
Empat lampu 75% hingga 100%
Lampu Tampilan Isi Daya yang Tersedia
Tiga lampu 50% hingga 75%
Dua lampu 25% hingga 50%
Satu lampu 10% hingga 25%
Lampu berkedip Rendah
Perangkat Baterai Terintegrasi:Ketika terhubung ke pengisi daya, jika semua lampu
tampilan mati, maka daya baterai telah terisi penuh. Lepaskan pengisi daya.
Hidupkan dan Matikan Mesin
Lihat Gambar:10,11,12,13
Hidupkan Mesin
PERINGATAN
Bahan bakar dan uapnya sangat mudah terbakar dan meledak.
Kebakaran atau ledakan dapat menyebabkan luka bakar parah atau kematian.
Saat Menyalakan Mesin
• Pastikan busi, knalpot, tutup tangki, dan pembersih udara (jika ada) berada pada
tempatnya dan terpasang dengan erat.
• Jangan menghidupkan mesin saat busi dilepas.
• Jika oli mesin meluap, setel choke (jika dipasang) ke posisi TERBUKA atau
BERJALAN, pindahkan throttle (jika dipasang) ke posisi CEPAT, lalu putar sampai
mesin menyala.
PERINGATAN
Penggunaan yang tidak benar dari baterai dan pengisi daya bisa
mengakibatkan sengatan listrik atau kebakaran.
Saat Mengoperasikan
• Jaga agar pengisi daya baterai tetap kering. Hindari pemaparan baterai terhadap
hujan atau kondisi basah.
• Untuk mengurangi risiko sengatan listrik, jangan biarkan air mengalir menuju
stopkontak AC.
• Jangan ada hubungan pendek/korsleting; jangan letakkan benda apa pun
bersinggungan dengan baterai.
PERINGATAN
BAHAYA GAS BERACUN. Gas buang mesin mengandung karbon monoksida,
yakni gas beracun yang dapat mematikan dalam hitungan menit. Anda TIDAK
DAPAT melihatnya, menciumnya, atau merasakannya. Meskipun Anda tidak
mencium asap gas buang, Anda masih bisa terpapar gas karbon monoksida.
Jika Anda mulai merasa mual, pusing, atau lemas saat menggunakan produk
ini, matikan produk, lalu cari udara segar SEGERA. Kunjungi dokter. Anda
mungkin keracunan karbon monoksida.
• Operasikan produk ini HANYA jika berada di luar ruangan, jauh dari jendela, pintu,
dan ventilasi untuk mengurangi risiko akumulasi gas karbon monoksida yang
berpotensi masuk ke dalam ruang hunian manusia.
• Pasanglah alarm karbon monoksida bertenaga baterai atau sambungkan alarm
karbon monoksida ke stopkontak listrik dengan baterai cadangan berdasarkan
petunjuk produsen. Alarm asap tidak dapat mendeteksi gas karbon monoksida.
• JANGAN mengoperasikan produk ini di dalam rumah, garasi, ruang bawah tanah,
kolong, gudang, atau ruang yang tertutup sebagian lainnya, bahkan dengan kipas
angin atau pintu dan jendela yang terbuka sebagai ventilasi. Karbon monoksida
dapat terkumpul dengan cepat di berbagai tempat tersebut dan bertahan selama
berjam-jam, bahkan setelah produk ini dimatikan.
• SELALU letakkan produk ini sesuai arah angin dan posisikan saluran gas buang
mesin menjauh dari tempat hunian manusia.
PEMBERITAHUAN Mesin ini dikirim dari Briggs & Stratton tanpa oli. Sebelum
menyala mesin, pastikan Anda menambahkan oli sesuai dengan petunjuk dalam
panduan ini. Apabila Anda menyala mesin tanpa oli, mesin akan mengalami
kerusakan permanen dan tidak akan ditanggung garansi.
Perhatikan:Peralatan mungkin dilengkapi kendali jarak jauh. Lihat panduan peralatan
untuk mendapatkan informasi tentang lokasi dan pengoperasian remote control.
1. Periksa oli mesin. Lihat bagianMemeriksa Tingkat Oli.
2. Model dengan baterai portabel:Pasang baterai (A, Gambar10) pada nampan
baterai mesin di bagian atas mesin. Pastikan bateraiterpasang dengan aman.
Baterai dapat mewakili kunci peralatan pada beberapa contoh.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
Simplicity 092J0B-0002-H5 ユーザーマニュアル
- カテゴリー
- 自動車アクセサリー
- タイプ
- ユーザーマニュアル
他の言語で
関連論文
-
Simplicity ENGINE, MODELS 11000B 120000B ユーザーマニュアル
-
-
-
Simplicity 305447-3201-B5 ユーザーマニュアル
-
-
-
-
Simplicity 44C677-S012-08 ユーザーマニュアル
-
Simplicity MANUAL, OPERATOR'S ユーザーマニュアル
-