V
Contact Retailer
N
o Tools
Required
＠ ＠
小
＠一
r、一
�
巾
。
小
。
巾
E
＠一
『、、·
N
�0
PARTS
。
。
。
。
x16
x16
x16
＠ x4
x4
x4
xl
� xl
x2
2
。
。
。
。
DO NOT OVERTIGHTEN
THE NUTS !
4 Secure hydraulic arms
Before connecting the hydraulic arm,
ensure the lifting mechanism is functioning
correctly - it should lift up and down freely
with adequate clearance on all sides.
。
。
。
。
厂、-
｀
I
｀
｀
x2 i
，
,
，
｀
｀
I ｀
｀
，，
，
\
\
＾
10
。
。
。
。
口
11
。
。
。
。
12
。
。
。
。
1
3
Hints and Tips
To operate the ottoman, always use 2 hands at arm's length and only where
illustration on this product. You must ensure the mattress is on the bed frame
before lifting the mechanism. Failure to do so may result in injury.
To ensure your safety please do not stand too close in case the frame bounces up.
The weight of the mattress loaded on the frame will keep the frame in a lower
position until it is pulled upwards by the user.
Do not attempt to move the bed whilst the frame is in the upright positon
If removing the mattress, make sure the frame is secured so it does not flip open. When
lifting the bed frame, remove pillows and covers.
PLEASE NOTE - It takes a lot of force to make the initial movement of the ottoman – THIS
IS A DESIGN FEATURE OF THE PRODUCT SO THAT IT DOES NOT FALL SHUT - and
the nearer to being closed the ottoman is, the easier it is to move. When the ottoman is
almost shut, it will close completely under its own weight.
When lowering the slat unit for the first time, take care to make sure it does not rub
unevenly on the inside face of the Side Rail. If it does, the bed has been assembled
slightly out of square. This can be rectified by moving the Footboard of the bed slightly to
the left or right whilst leaving the headboard of the bed frame stationary.
Tip for difficulty with compression:
If you are experiencing difficulty with the initial compression try fitting one piston at a time
(following the Assembly Instructions) then press down on the side of the frame with the
piston fitted - this acts like a big lever (The weight of the mattress can be used to
supplement the load exerted). Effectively you are doubling the amount of force applied,
because you have halved the resistance offered by the pistons. It can take slightly more
effort than you might feel comfortable applying to the bed frame at first.
1
4
Do not attempt to move the bed whilst the frame is in the upright
positon.
1
5
GENERAL CARE & MAINTENANCE
We advise that when cleaning the product that a damp cloth is used.
Avoid the use of all household cleaners and abrasive.
Never push or drag the furniture.
Never attempt to move the furniture when fully loaded.
We advise that periodically all fixing are re-tightened.
1
6
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Julian Bowen MAI117 Assembly Instructions Manual
- タイプ
- Assembly Instructions Manual
他の言語で
- English: Julian Bowen MAI117
その他のドキュメント
-
Burmeier DALI 取扱説明書
-
Joie P1814A ユーザーマニュアル
-
mothercare Wayfarer ユーザーガイド
-
Candy CBTD 7A1TE-CN/ ユーザーマニュアル
-
mothercare Appleby Cot Bed ユーザーガイド
-
-
Simplicity RIDER, ZTR, EXPORT ユーザーマニュアル
-
-
-
Dorel Home 8173296CC Assembly Manual
