1
红色
黑色
红色线连接汽车电源DC12V+，黑色线连接汽车电源
DC12-，蓝色LED点亮，进入待机模式。
2
将具有无线电源接收功能的手机放置产品线圈中间
位置，绿色LED点亮，即可以实现无线充电功能。
绿色LED点亮
3
充电完成，取走手机。绿色LED熄灭。蓝色LED点亮。
绿色LED
蓝色LED
1
red
black
Connect red line to car power DC12V+, Connect
black line to car power DC12V-. When red light
on the device is in standby mode.
2
Put mobile phone with wireless charging receiver
into the area of 3 coils. The blue light will be on
which means wireless charging is working.
Green LED lights up
3
Green light on means charging full. When take
mobile phone away, the green light will be off
and red light will be on.
Green LED
Blue LED
Take away the phone
注意
当充电器上的接收装置放置的位置不对，或放置非Ql标
准指定发射装置时充电器不进行充电。
当手机放上去的时候出现错误，需拿起来重放，而不是
继续放著左右对位。
相容性
本无线充电产品可以对市场上符合WPC标准的接收器相
容使用。
① 开关
② 充满电-绿色
③ 待机灯-红色
④ 充电灯-蓝色
⑤ 充电线圈1
⑥ 充电线圈2
⑦ 充电线圈3
开关功能说明：
A:关机功能：待机红色LED灯状态下长按三秒,红色LED闪烁后关机.
B:开机功能：关机状态下长按三秒红色LED灯闪烁后开机。
C:模式切换：短按一下由模式1与模式2循环切换。
LED模式功能说明
模式1 支持 充电 充满 错误
红色LED 开
开
开关
关
关
关
关
关关
关绿色LED
蓝色LED
闪烁
① Power -key
② LED_Charging-green
③ LED_Standby-red
④ LED-Standby-blue
⑤ COLL1-Charging
⑥ COLL2-Charging
⑦ COLL3-Charging
Switch On/ Off：
A: Switch Off：When under standby mode, red light is on, push switch last
for 3 seconds. Red light flashes then power off.
B: Switch on：When under power off, push switch last for 3 seconds.
Red light flashes then power on.
C: Mode Switch：Push switch one time will switch mode1 to mode 2 circularly.
LED Mode Function Guide
Mode1 Standby Charging Charging
Full Error
Red On
On
On
Off
Off
Off
Off
Off
Off Off
Off
Green
Blue
Blink Slow
Notice：
·Please use qualified Qi receiving device for charging. If the
position of receiver is not right, It may show no connection or
cannot charge. Please adjust the position.
Compatibility：
·This production is compatible with all wireless charging
receiver with WPC standard.
当pcba处
于待机状
态时，led
灯将会亮
着。led的
颜色和功
能将根据
右边这个
功能图。
模式2 支持 充电 充满 错误
红色LED
开
开关
关
关
关
关
关
关关
关绿色LED
蓝色LED
闪烁
当pcba处
于待机状
态时，led
灯将会亮
着。led的
颜色和功
能将根据
这个图。
Mode 1.
While the
PCBA is in
standby the
LED light will
be on. The
LED color
and function
will be
according to
this diagram.
Mode2 Standby Charging Charging
Full Error
Red
On
On
Off
Off
Off
Off
Off
Off
Off Off
Off
Green
Blue
Blink Slow
Mode 2.
While the
PCBA is in
standby the
LED light will
be on. The
LED color
and function
will be
according to
this diagram.
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the
party responsible for
compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide
reasonable protection against harmful interference in a residential
installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio
communications. However, there is no guarantee that
interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or
television reception, which can be determined by turning the
equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following
measures:
Reorient or relocate the receiving an tenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an
uncontrolled environment. This equipment should be installed and
operated
with minimum distance 20cm between the radiator & your body
①
②
③
④
⑤
⑥
⑦
①
②
③
④
⑤
⑥
⑦
9906PCB-2
车载无线充电模块
充电使用说明书
9906PCB-2
Wireless Charging Module
for Vehicle
Using Guide
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM
Manual v01
2.2 List of applicable FCC rules
FCC Part 15 Subpart C 15.207 & 15.209
2.3 Specific operational use conditions
The module is a Wireless charger module with Wireless charger function.
Operation Frequency: 110.1-205KHz
Modulation: MSK
Type: Inductive loop coil Antenna
Gain: 0 dBi Max.
This module should be installed and operated with minimum distance 20cm between the radiator &
your body with a maximum 0dBi antenna. The host manufacturer installing this module into their
product must ensure that the final composit product complies with the FCC requirements by a
technical assessment or evaluation to the FCC rules, including the transmitter operaition. The host
manufacturer has to be aware not to provide information to the end user regarding how to install or
remove this RF module in the user's manual of the end product which integrates this module. The end
user manual shall include all required regulatory information/warning as show in this manual.
2.4 Limited module procedures
The module is approved as a “limited module” without shielding.The device can be used in mobile
exposure conditions only.This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
2.5 Trace antenna designs
Not applicable. The module has its own antenna, and doesn’t need a host’s printed board microstrip
trace antenna etc.
2.6 RF exposure considerations
The module must be installed in the host equipment such that at least 20cm is maintained between the
antenna and users’ body; and if RF exposure statement or module layout is changed, then the host
product manufacturer required to take responsibility of the module through a change in FCC ID or new
application. The FCC ID of the module cannot be used on the final product. In these circumstances,
the host manufacturer will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
2.7 Antennas
Antenna Specification are as follows:
Type: Inductive loop coil Antenna
Gain: 0 dBi
This device is intended only for host manufacturers under the following conditions:
The transmitter module may not be co-located with any other transmitter or antenna;
The module shall be only used with the internal antenna(s) that has been originally tested and certified
with this module. The antenna must be either permanently attached or employ a ‘unique’ antenna
coupler.
As long as the conditions above are met, further transmitter test will not be required. However, the
host manufacturer is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
2.8 Label and compliance information
Host product manufacturers need to provide a physical or e-label stating “Contains FCC ID: 2AQPB-
9906PCB-2” with their finished product.
2.9 Information on test modes and additional testing requirements
Operation Frequency: 110.1-205KHz
Modulation: MSK
Host manufacturer must perfom test of radiated & conducted emission and spurious emission, etc
according to the actual test modes for a stand-alone modular transmitter in a host, as well as for
multiple simultaneously transmitting modules or other transmitters in a host product.
Only when all the test results of test modes comply with FCC requirements, then the end product can
be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for FCC Part 15 Subpart C 15.207 & 15.209 and that
the host product manufacturer is responsible for compliance to any other FCC rules that apply to the
host not covered by the modular transmitter grant of certification. If the grantee markets their product
as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then
the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
/
