SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
No.11926
REQUIRED FOR OPERATION
BEFORE YOU BEGIN
ASSEMBLY
OPTIONAL PARTS
OPERATING YOUR MODEL SAFELY
WINGSPAN: 1475mm
SAFETY PRECAUTIONS
This radio control model is not a toy!
First-time builders should seek the advice of experienced modellers
before commencing assembly and if they do not fully understand
any part of the construction.
Assemble this kit only in places out of childrenÕs reach!
Take enough safety precautions prior to operating this model.
You are responsible for this modelÕs assembly and safe operation!
Always keep this instruction manual ready at hand for quick
reference, even after completing the assembly.
THE FINEST RADIO CONTROL MODELS
R
INSTRUCTION MANUAL
2
3
3~10
11
11~12
RADIO CONTROLLED ENGINE POWERED ALL-BALSA ACROBATIC AIRCRAFT
CAP 232-60
BREITLING
© 2000 KYOSHO
232-60
INDEX
Before commencing assembly, please read these instructions thoroughly!
For Intermediate
&
Advanced flyers.
1
4
A minimum 4 channel transmitter
for aircraft.With 5 servos.
For handling the radio properly, refer to its instruction manual.
Sharp Hobby Knife
Phillips Screwdriver (L, M, S)
Drill,Tap,Handgrinder
Needle Nose Pliers
Awl
Scissors
2
Model Airplane Engine
Muffler
Engine and Muffler
Glow Plug
Wire Cutters
3
Required for engine starting:
Fuel Primer
Plug Wrench
2
2 aileron extension
cords
1
1 Y- harness
5
Glow engine fuel only.
M
ODEL
ENG
INE
FUEL
6
SILICON
Epoxy A
Epoxy B
Instant Glue
30
Epoxy Glue (30 minutes type)
Silicon Glue
Glue
Purchase a propeller that
will match your engine.
Propeller and Spinner
CAUTION
: For details concerning the equipment listed below
(size, maker, etc.), check with your hobby shop.
CAUTION
: Only use a minimum 4 channel radio for aircraft!
(No other radio may be used!)
WARNING: Normal gasoline
cannot be used with
glow engines.
2 46 60
4 70 91
2-stroke .46 .60
4-stroke .70 .91
Engine Starter
12V
12V Battery (for starter)
Other equipment for enhancing airplane operation & performance
Fuel Filter
Spinner(62mm
Propeller
4
Fuel line
Sponge Sheet
4
5
A minimum 4 channel radio for airplanes (with 5
standard servos), and nicad or alkaline batteries are
required.
8
Linkage Parts
7
Please use stronge control horns and pushlods
intended for large sized models.
2
TOOLS REQUIRED (Purchase separately!)
REQUIRED FOR OPERATION (Purchase separately!)
One-touch Plug Heater Set
3
1
Check all parts. If you find any defective or missing parts, contact your local dealer or our Kyosho Distributor.
2
5
Symbols used throughout this instruction manual, comprise:
4
You can keep the covering film from wrinkling or peeling by spraying the plane with clear polyurethane.
3
Changes in weather may cause the covering film to slacken.If necessary,use a heat gun or iron to tighten the
covering.
Main Wing
Apply epoxy glue.
Assemble left and right
sides the same way.
Must be purchased separately!
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Cut off excess.
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
Do not overlook this
symbol!
Pay close attention here!
Tow kinds of hinges are used on each surface,
Make sure only epoxy is used on the metal hinges
and only CA glue is used on the nylon hinges.
Warning!
Align the center line of main wing
with aileron.
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Warning!
Make certain the hinges are adequately secured with
glue.If they come loose in flight accidents may result.
1
Secure metal hinges with epoxy being
careful to avoid geting glue in the
hinge pin areas.
Metal Hinge
Secure nylon hinges with instant glue,
being careful not to glue the wing and
aileron together.
Nylon hinge
ASSEMBLY
low setting
Use an iron covered with a cloth!
Start at low setting. Increase the set--
ting if necessary. If it is too high, you
may damage the film.
with cover (cloth)
The pre-covered film on ARF kits may wrin-kle due to
variations of temperature. Smooth out as explained
Make certain linkages are strong and secure.Reduce play to a minimum
for best peformance.
Cut off shaded portion.
Cut away film only
here.
4
Apply epoxy glue.
Assemble left and right sides
the same way.
Must be purchased separately!
Main Wing
4
2
Aileron Servo
Set all screws securely.If they come
off during flight yoo will lose control
of yoor aircraft!
Do not disregard this symbol!
Warning!
Warning!
Cut the mount
to fit your servo.
When cutting the film coverring,Do not cut too
deeply to avoid weakening The wood structure
beneath.
Pay close attention here!
Top view
Bottom view
Main Wing(Botton view)
Ensure that the two wing halves are
securety glued together with epoxy.
Warning!
Cut away covering film only in these locations.
Top view.
Main Wing
3
Note the direction.
Top
Use epoxy glue
to fill the opening.
Dihedral.
55mm
Main wing underside
AÕA
Engine Mount
6
4 x 20mm
Screw
4
4
4x20mm
4mm
A/2
A/2
4mm
Mount Nut
3.5
mm
A
5
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Throttle Rod
Depends on
the position
of carburettor.
5mm
When using a
2stroke engine.
2
When using a
4stroke engine.
4
Position the engine so the fit the mufller exits the fuse and the engine shaft is centered on the firewall as shown.
Use the mufller
adapter for clear
the mufller to
cowling.
Must be purchased separately!
Make certain wing securely attaches to fuse. erratic flight
and/or crashes can result if it comes loose during flight.
Main Wing
5
Bottom view
4 x 40mm
4mm
A = AÕ
4mm
Washer
4 x 40mm
Screw
2
2
Warning!
4.2mm
Pay close attention here!
Do not disregard this symbol!
Warning!
6
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
130mm
8
Engine Mount
4mm
4
4
4
Engine Mount
Spring Washer
4mm
Washer
4mm
4x25mm
4mm
Spring Washer
Nut
4mm
4 x 25mm
Cap Screw
4mm
Nut
4mm
Washer
4
3 5mm
5mm
After confirming the posi-tion of the
fule tank's internal parts(see front
view), insert and tighten the screw.
Sillicon tube
1
Fuel tank
3 x 25mm TP
TP Screw
Fix tank in fuselage with silicon glue.
7
Horizontal / Vertical Tail
10
Warning!
2.6 x 8mm
2mm
2mm
7
Apply epoxy glue.
2mm
Drill holes with the specified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
Do not disregard this symbol!
Warning!
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(CA glue, super glue).
Assemble left and right sides
the same way.
L
L
2
2.6 x 8mm TP
TP Screw
Bend at end of rod.
Secure nylonhinges with instant glue.
Being careful not to glue the fin and
rudder together.
Make certain parts are
aligned accurately and play
is reduced to a minimum.
A AÕ
BÕ B
C
CÕ
A = AÕ B = BÕ
C = CÕ
Cut away only
covering film.
Cut away only
covering film.
Warning!
Vertical/Horizontal Tail
Make certain plane is aligned accurately
per the diagram. A mis-aligned plane
can fly erraticaliy and cause accidents.
Secure metalhinges with epoxy.
Being careful to avoid getting glue
in the hingepin areas.
9
When cutting the film coverring, Do not
cut toodeeply to avoid weakening The
wood structurebeneath.
Linkage lod
Linkage
8
Must be purchased separately!
12
Do not disregard this symbol!
Warning!
Elevator Servo
Receiver
Warning!
Make certain linkages are strong and secure. Reduce play to a
minimum for best performance.
Rudder Servo
Throttle Servo
Make certain parts are alignedaccurately and play is reduced
to a minimum. Tighten screwssecurely.
Main Landing Gear.
2
2
4mm
Washer
2
4mm
Spring washer
2
4mm4mm
6
4mm
Nut
4mm
4mm
4mm
4mm
4mm
4 16mm
4mm
4 x 40mm
Screw
4 x 16mm
Screw
Attach gearpant and wheel to
leg using parts provided making
certain wheel rotates freely.
11
Ensure smooth non-binding
movement while assembling.
4mm
Drill holes with the specified
diameter (here: 2mm).
4mm
Pay close attention here!
13
Linkage
Linkage lod
Relive the cowl to
clear the engine hed.
Relive the cowl
to clear the
mufller.
Cut away film only.
9
Must be purchased separately!
Do not disregard this symbol!
Warning!
Rudder Horn
Elevator Horn
Warning!
2mm
14
Couling
2.6 x 8mm TP
TP Screw
4
2mm mm
mm
3mm
L
Pay close attention here!
Apply epoxy glue.
Make certain linkages are strong and secure. Reduce play to a
minimum for best performance.
Make certain parts are aligned
accurately and play is reduced to
a minimum. Tighten screws securely.
Assemble left and right sides
the same way.
L
2mm
Drill holes with the specified
diameter (here: 2mm).
2mm
Cut off shaded portion.
Color paint
Color paint
2 x 8mm TP
TP Screw
2.6 x 8mm
4
2mm
10
2mm
pecified
diameter (here: 2mm).
Cut off shaded portion.
2mm
Pay close attention here!
Canopy
15
22mm
22mm
17mm
17mm
11mm
11mm
RUDDER
ELEVATOR
AILERON
Adjust the travel of each control surface to the values in the diagrams.
UP
DOWN
16
Decal
17
Apply included decals. For the correct placement of
decals, please refer to box top.
CG
65 75mm
Reference point for
diagram at right.
Reference point for
diagram at right.
Reference point for
diagram at right.
Must be purchased separately!
This aircraft is for intermediate to advanced builders and flyers only. Biginners connot fly and building this aircraft.
This aircraft has been flight tested with snap-rolls and other aerobatic maneuvers.However,repeated violent
maneuvers may overstress the airframe. Please fly in a way that will not otherstress the airframe.
Repeated flyng can cause stress cracks to appear in the wood and joints, please inspect after each flight. If any
abnormalities are noted, repair immediately befor the next flight to avoid accsidents.
Glue joints can loosen even thoogh they appear to be tight. If you notice irregular flight, investigate the cause and
repair it befor the next flight.
This aircraft is designed for 2 stroke .46-.60 or 4 stroke .70 -.91 sized engines only. Using larger,more powerful
engens is not safe and may result in airframe failure.Do not exceed the recommended engine size or engage in
extreme aerobatic maneuvers.
Do not overlook this symbol!
Warning!
1100
Fuel Tube Stopper
91490
90693
400cc
Fuel Tank 400cc
2000
25mm
Sponge Tire 25mm, Tail Gear Assy
60mm
Sponge Tire 60mm
800
90906
90845-60
90845-25
90431-40
350
90421-62
62mm
Nylon Spinner (White) 62mm
62mm
Nylon Spinner (Red) 62mm
62mm
Nylon Spinner (Yellow) 62mm
1000
90420-62
62mm
Duraluminium Spinner 62mm
4000
90426-62
SP OS70 120
SP Adapter Nut O.S. .70~.120
SP OS63 120
SP Adapter Nut YS .63~.120
2600
90487-08
300
200
90469
2600
90487-07
4000
90422-62
PP
90903
1000
11
Warning!
PARTS
No. Part Names Quantity
11926-01
11926-02
Cowling
Main Gear
1
1
11926-03
1
4500
1500
2000
No. Part Names
FOR JAPANESE MARKET ONLY.
Quantity
FOR JAPANESE MARKET ONLY.
11926-04
11926-05
Canopy
(a),(b),(c)
Decale
3000
2300
OPTIONAL PARTS
No. Part NamesNo. Part Names
Wheel Pants
(R) (L)
(R) 1,(L) 1
200
200
200
200
1400
2000
00
0 0 2 1 0 4 4 7 2 7 1
1 6 8 0
0 0 2 1 0 4
4 7 2 7 1
1 6 8 0
1,400
200
80
1,680
(1)
(2)
(2)
(3)
(4)
(1)
"Kyosho Direct-Mail-Parts-Order-System" is available only for Japanese market
11926
CAP 232-60 BREITLING
The servise mentioned below is available only for Japanese market.
OFF
ON
Pre-Flight Checks
Only fly model aeroplanes in areas
away from houses and places
where people gather. The weight
and speed of your aeroplane make
it a potential hazard. Make sure
that the area around you is clear.
For radio equipment, refer to the
instruction manual included with
your set.
Check that the spinner and the
propeller are securely fastened.
If the model begins to operate by
itself, there is another transmitter
operating on your frequency. Do
not try to operate your model if
this happens, but change your
transmitter and receiver crystals
to another frequency.
Fully extend
transmitter
aerial.
Switch on the transmitter.
Switch on the receiver.
Check that the wings are properly
and firmly affixed.
Flying
Fill the fuel tank.
By moving the various transmitter
controls, ensure that all control
surfaces move the way you
intend them to.
To start the engine, set low throttle
on the transmitter and hold the
engine starter against the spinner.
Switch on engine starter.
Adjust the throttle needle.
After Flying
Only use KYOSHO genuine parts.
Safety Precautions
Always regulate the engine from behind,
but never from infront or from the sides,
because a rotating propeller might badly
injure you.
Do not allow watching people to get too
close to a rotating propeller.
Immediately disuse defective propellers
as well as deformed spinners.
If the batteries of the radio system
are flat, replace them with new ones.
Do not fly your airplane above people
standing around.
ON
ON
Launch the aeroplane into the wind.
Do not fly your aeroplane if it is a
windy day or there are strong
cross winds.
Always land your airplane into the
wind.
Bring your airplane to a halt by
lowering the engine control trim.
After each flight, the engine is hot. Be-
ware of getting burned.
Wipe up any fuel deposits or dirt.
Never throw burning, gleaming or smoul-
dering things into fuel cans, even if
these happen to be empty. This could
result in serious injury.
WIND
WIND
OFF
OFF ON
Switch off the receiver.
Switch off the transmitter.
OFF
Draw the remaining fuel out of the tank
and fill it back into the can.
Move the throttle control stick
on the transmitter and check
that the carburettor opens and
closes easily.
R
THE FINEST RADIO CONTROL MODELS
PRINTED IN CHINA
62150006-1
Non-observance of this information could lead to serious injury and/or damage to property.
Warning!
FLIGHT MANUAL
243-0034 153
TEL.046-229-4115
( ) 10:00~18:00
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
他の言語で
関連論文
-
Kyosho G-TRICK 90 ユーザーマニュアル
-
-
-
-
-
-
-
-
-