Compact Disc
Player
© 2001 Sony Corporation
4-233-300-51(2)
CDP-CE375
Operating Instructions
Mode d’emploi
Manual de instrucciones
FR
ES
FR
FR
GB
FR
ES
FR
CT
2
GB
About this manual
The instructions in this manual is for CDP-CE375.
Tip
Instructions in this manual describe the controls on
the player.
You can also use the controls on the remote if they
have the same or similar names as those on the
player.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
This appliance is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT
MARKING is located on the rear exterior.
AC power cord must be changed only at the qualified
service shop.
Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
To prevent fire, do not Cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Don’ throw a battery, this pose
it as the injurious wastes.
3
GB
Table of Contents
Parts Identification 4
Front Panel ..............................................................................................................................4
Rear Panel................................................................................................................................5
Remote Control ....................................................................................................................... 5
Getting Started
Inserting Batteries Into the Remote Control............................................................................6
Hooking Up the System ..........................................................................................................6
Playing CDs
Loading the CD ....................................................................................................................... 7
Playing the CD –– Normal Play/Shuffle Play/Repeat Play..................................................... 8
Using the CD display ..............................................................................................................9
Replacing Discs While Playing a Disc ..................................................................................10
Programming the CD tracks ..................................................................................................11
Fading In or Out ....................................................................................................................12
Recording From CDs
Recording a CD by Specifying Tape Length (Time Edit).....................................................12
Adjusting the Recording Level (Peak Search) ......................................................................13
Additional Information
Precautions ............................................................................................................................14
Notes on CDs......................................................................................................................... 14
Troubleshooting..................................................................................................................... 15
Specifications ........................................................................................................................15
FRGB
4
GB
CHECK w; (11, 12)
CLEAR 9 (11, 12)
DISC 1–5 2 (8, 9, 11)
Disc compartment qj (7)
DISC SKIP 8 (7, 10, 12)
Display 3 (9)
EX-CHANGE 7 (10, 13)
FADER qd (12)
PEAK SEARCH qs (13)
PHONES jack wa (9)
PLAY MODE qa (8, 9, 11, 13)
POWER 1 (7)
Remote sensor qh (6)
REPEAT qf (8)
TIME qg (9, 10)
TIME EDIT ql (12)
Parts Identification
Front Panel
The items are arranged in alphabetical order.
Refer to the pages indicated in parentheses ( ) for details.
BUTTON DESCRIPTIONS
A OPEN/CLOSE ws (7, 9)
H 4 (8, 11, 13)
X 5 (9, 13)
x 6 (9, 13)
lAMSL dial 0 (9, 11, 13)
m/M qk (9, 12)
5
GB
Rear Panel
Remote Control
Parts Identification
5
GB
ANALOG OUT L/R jacks 2 (6)
DIGITAL OUT OPTICAL jack 1 (7)
Mains lead 3 (6)
ANALOG OUT LEVEL +/– qs
(6, 7)
CONTINUE 2 (8)
DISC SKIP 9 (7, 10, 12)
PROGRAM 8 (8)
REPEAT 3 (8)
SHUFFLE 1 (8)
TIME 0 (9, 10)
BUTTON DESCRIPTIONS
N 5 (8, 11, 13)
X 4 (9, 13)
x qa (9, 13)
. AMS > 6 (9, 11, 13)
m/M 7 (9, 12)
6
GB
Getting Started
Inserting Batteries Into
the Remote Control
You can control the player using the supplied
remote.
Insert two R6 (size AA) batteries by matching
the + and – on the batteries to the diagram
inside the battery compartment.
Insert the negative (–) end first, then push in
and down until the positive (+) end clicks into
position.
When using the remote, point it at the remote
sensor
on the player.
Tip
When the remote no longer operates the system,
replace both batteries with new ones.
Note
• Do not leave the remote near an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you don’t use the remote for an extended period
of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
Hooking Up the System
Hookups
This section describes how to hook up the CD
player to an amplifier. Be sure to turn off the
power of each component before making the
connections.
Tip
You can adjust the analog output level to the
amplifier using the remote comes with this player.
Press ANALOG OUT LEVEL +/– on the remote.
You can reduce the output level up to –20 dB.
When you reduce the analog output level, “FADE”
appears in the display.
When you turn off the player, the analog output level
automatically returns to the maximum level.
Setting the voltage selector
(voltage selector equipped
models only)
Check that the voltage selector on the rear
panel of the player is set to the local power line
voltage. If not, set the selector to the correct
position using a screwdriver before connecting
the AC power cord to a wall outlet.
CD player
Audio input
(White) (L)
: Signal flow
Amplifier
To mains
To mains
Audio input
(Red) (R)
ANALOG
OUT
(Red) (R)
ANALOG OUT
(White) (L)
110 - 120 V220 - 240 V
Getting Started
7
GB
Making digital hookups
If you have a digital component such as a
digital amplifier, D/A converter, DAT, or MD,
connect the component via the DIGITAL OUT
(OPTICAL) connector using the optical cable
(not supplied). Take off the cap and plug in the
optical cable.
Note that you cannot use the following
functions when making this connection:
• Fading In or Out (see page 12)
• Adjusting the output level using the
ANALOG OUT LEVEL +/– buttons on the
remote
Note
When you connect via the DIGITAL OUT
(OPTICAL) connector, noise may occur when you
play CD software other than music, such as a CD-
ROM.
Transporting the player
Before transporting the player, follow the
procedure below to return the internal
mechanisms back to their original position.
1 Remove all the discs from the disc tray.
2 Press A OPEN/CLOSE to close the
disc tray.
“no dISC” appears in the display.
3 Wait for 10 seconds, then press
POWER to turn off the player.
POC-15
Optical cable (not supplied)
Digital component
CD player
Loading a CD
1 Turn on the amplifier and select the CD
player position so that you can listen to
the sound from this player.
2 Press POWER to turn on the player.
3 Press AOPEN/CLOSE.
The disc compartment slides out.
4 Place a disc on the disc tray with the
label side up.
5 To place other discs, press DISC SKIP
and place the discs in the order you
want to play.
Each time you press the button, the disc tray
turns and you can place the discs in the
empty disc compartments. The player plays
the disc in front of you first.
6 Press AOPEN/CLOSE to close the disc
compartment.
Playing CDs
When you play a CD single,
place it on the inner circle
of the tray.
Disc number
Playing CDs
DIGITAL
OUT
OPTICAL
DIGITAL
INPUT
OPTICAL
8
GB
Repeat Play Operations
You can play the CD tracks repeatedly in any
play modes.
To activate the Repeat Play function, press
REPEAT until “REPEAT’ appears in the
display.
To
Repeat only one track
Cancel Repeat Play
When you are in the Repeat Play function, the
player repeats the tracks as follows:
When the disc is
played in
Continuous Play
(ALL DISCS)
Continuous Play
(1 DISC)
Shuffle Play
(ALL DISCS)
Shuffle Play
(1 DISC)
Programme Play
(page 11)
Playing the CD
––Normal Play/Shuffle Play/Repeat
Play
This unit lets you play the CD in different play
modes.
1 Press PLAY MODE repeatedly until the
mode you want appears.
2 Press H.
Tips
• You can select the disc you want to start playing
first by pressing one of the DISC 1 – 5 buttons.
• You can specify discs during ALL DISCS Shuffle
Play mode, and the tracks on the specified discs are
played in a random order.
Press DISC 1 – 5 to specify the discs after Step 1.
Semi-circles appear around the specified disc
numbers in the display. To cancel the selected discs,
press DISC 1 – 5 again. The semi-circles disappear.
To return to ALL DISCS Shuffle Play, press PLAY
MODE until “ALL DISCS SHUFFLE” appears in
the display.
• You can select the playing mode by pressing
CONTINUE, SHUFFLE, or PROGRAM on the
remote.
Select
ALL DISCS
(Continuous
Play)
1 DISC
(Continuous
Play)
ALL DISCS
SHUFFLE
1 DISC
SHUFFLE
PROGRAM
To play
All discs in the player
consecutively in the order of disc
number.
Only the disc you’ve selected.
All tracks on all discs in random
order.
All tracks on the specific disc in
random order.
The tracks on the CD in the
order you want them to be
played (see “Programming the
CD tracks” on page 11).
Press REPEAT
Until “REPEAT 1” appears
while playing the track you
want to repeat.
Until “REPEAT” or
“REPEAT 1” disappears.
The player repeats
All the tracks on all discs
All the tracks on the current
disc
All the tracks on all discs in
random order
All the tracks on the current
disc in random order
The same programme
Playing CDs
9
GB
Other Operations
To
Stop playback
Pause
Select a track
Go to the next disc
Select a disc directly
Find a point in a track
Play tracks in random
order
Remove the CD
Adjust the volume
Tips
• You can adjust the analog output level with the
ANALOG OUT LEVEL +/– on the remote (page
6).
• You can adjust the headphones volume on the
remote. To adjust the volume, connect the
headphones to the PHONES jack and adjust the
volume with the ANALOG OUT LEVEL +/– on
the remote.
• If there is no CD in the player, “no dISC” appears
in the display.
Notes
• If “ ” appears in the display, the disc has
reached the end while you were pressing M. Press
m or turn lAMSL counterclockwise to go
back.
• If you press ANALOG OUT LEVEL buttons on the
remote while recording, the recording level will
change even when it is preset on the tape deck, etc.
Using the CD display
You can check information about the disc using
the display.
In the stop mode
Press TIME.
The display shows the current disc number, the
total number of tracks, total playing time and
music calendar.
The information also appears when you press
AOPEN/CLOSE to close the disc tray.
The tracks numbered over 20 cannot be
displayed in the music calendar.
Notes on the disc number
indications
• The red circle around a disc number
indicates the disc is ready to be played.
• When all the tracks on a disc have been
played, the semi-circle around the disc
number disappears.
• When a disc compartment is recognized as
empty, the semi-circled disc number
disappears.
During normal playback
While playing a disc, the display shows the
current disc number, track number, playing
time of the track and the music calendar.
The track numbers in the music calendar
disappear after they are played.
Do this
Press x.
Press X. Press X again or
H to resume play.
During play or pause, turn
lAMSL clockwise
(to go forward) or
counterclockwise (to go
backward)
(or press >( to go
forward) or . (to go
backward) on the remote).
Press DISC SKIP.
Press DISC 1 – 5.
Press and hold M or m
during playback, and
release at the desired point.
Press PLAY MODE until
“SHUFFLE” appears in the
display.
Press AOPEN/CLOSE.
Press ANALOG OUT
LEVEL +/– on the remote.
Total number of tracks
Music calendar
Total playing time
Current disc number
continued
12345
678910
1 2 3 4 5
DISCSALL
TRACK
DISC
MIN
SEC
110 45 28
10
GB
To check the remaining time
Press TIME during playback.
Each time you press this button while playing a
disc, the display changes as shown in the chart
below.
Playing time and number on the current track
t Remaining time on the current track t
Remaining time on the disc
Notes
• When the disc has more than 24 tracks, “– – . ––”
appears instead of the remaining time.
• The remaining time on the disc appears only when
the disc is played in Continuous Play.
Replacing Discs While
Playing a Disc
You can open the disc tray while playing a disc
so that you can check what discs are to be
played next and replace discs without
interrupting playback of the current disc.
1Press EX-CHANGE.
The disc tray opens and two disc
compartments appear. Even if the player is
playing a disc, it doesn’t stop playing.
2Replace discs in the compartments
with new ones.
The player plays the disc on the left side
compartment after the current disc, and then
the one on the right side compartment.
3Press DISC SKIP.
The disc tray turns and other two disc
compartments appear.
4Replace discs in the compartments
with new ones.
5Press EX-CHANGE.
The disc tray closes.
While the disc tray is open by
pressing the EX-CHANGE button
• If the playback of the current disc ends, the
player stops playing. If the disc is played in
1 DISC Repeat Play mode (see page 8), the
current disc starts playing again.
• In ALL DISCS Shuffle Play mode (see page
8), tracks are reshuffled on the current disc.
• In Programme Play mode (see page 11), only
the tracks on the current disc are played.
• Do not push the disc tray to close it in
Step 5, as you may damage the
player.
Using the CD display (continued)
Playing CDs
11
GB
Programming the CD
tracks
You can arrange the order of the tracks on the
discs and create your own programme. The
programme can contain up to 32 “steps” — one
“step” may contain a track or a whole disc.
1 Press PLAY MODE repeatedly until
“PROGRAM” appears in the display
before you start playing.
If a programme is already stored, the last
step of the programme appears in the
display. When you want to erase the whole
programme, hold down CLEAR until “ALL
CLr” appears in the display (see page 12).
2 Press DISC 1 – 5 to select the disc.
“AL” in the display stands for “all” tracks.
When you want to programme the whole
disc as one step, skip Step 3, and go to Step
4.
3 Turn lAMSL until the track you
want appears and push lAMSL to
select the track.
The track number that you programmed, the
playing order, and the total playing time
appear in the display.
If you’ve made a mistake
Press CLEAR, then repeat Step 2.
4 To programme other discs or tracks, do
the following:
5 Press H to start Programme Play.
To cancel Programme Play
Press PLAY MODE.
Tips
• You can create your programme while checking the
disc labels.
While the disc tray is open, follow Steps 1 to 4 with
pressing the DISC SKIP button to check the disc
labels. If you close the disc tray before Step 5, the
total playing time appears in the display after a
while.
Note that, if the programmed track number isn’t
found on the disc, that step is automatically erased.
• The programme remains even after the Programme
Play ends. When you press the H button, you can
play the same programme again.
• The programme remains until you erase it or turn
off the player. If you replace discs, the programmed
disc and track numbers remain. So, the player plays
only the existing disc and track numbers. However,
the disc and track numbers that aren’t found in the
player or on the disc are deleted from the
programme, and the rest of the programme is played
in the programmed order.
• For the recording to the A side or B side of the
cassette tape, you can pause Programme Play.
Note
The total playing time doesn’t appear when:
—You have programmed a track whose number
exceeds 20.
—The total playing time of the programme exceeds
200 minutes.
Checking the track order
You can check your programme before or after
you start playing.
Press CHECK.
Each time you press this button, the display
shows the track (the disc and track numbers) or
the disc (the disc number and “AL” indication)
of each step in the programmed order. After the
last step in the programme, the display shows
“End” and returns to the original display. If you
check the order after you start playing, the
display shows only the remaining steps.
To programme
Other discs
Other tracks on the
same disc
Other tracks on
other discs
Repeat Step(s)
2
3
2 and 3
continued
12
GB
Changing the track order
You can change your programme before you
start playing.
To
Erase a track
Erase the last track
in the programme
Add tracks to the
end of the
programme
Change the whole
programme
completely
Fading In or Out
You can manually fade in or out to prevent
tracks from starting or ending abruptly.
Note that you cannot use this effect when you
use the DIGITAL OUT (OPTICAL) connector.
To
Start play fading in
End play fading out
Fading time lasts for 5 seconds.
Press FADER
During pause. “FADE” flashes.
The play fades in.
When you want to start fading
out. “FADE” flashes. Then play
fades out and the player pauses.
Recording From CDs
Recording a CD by
Specifying Tape Length
(Time Edit)
You can have the player create a programme
that will fit the length of the tape.
The player automatically creates a programme,
keeping the original order of the disc.
The programme can contain up to 32 steps (a
pause inserted between steps is counted as one
step).
Note that tracks numbered over 20 cannot be
programmed automatically.
1Press DISC SKIP to select the disc.
2Press TIME EDIT repeatedly before you
start playing until “EDIT” appears and
“A” in the
A
indication flashes in the
display.
3Press m or M to specify the tape
length.
Each time you press these buttons, the
display changes as shown below, with the
tape length of one side following each
indication.
4Press TIME EDIT to have the player
create the programme.
The display shows the tracks to be recorded.
“B” in the
AB
indication flashes in the
display.
5When you record on both sides of the
tape, press TIME EDIT again.
The player inserts a pause, then creates the
programme for side B. The display shows
the programmed tracks.
When you record on one side of the tape,
skip this step.
You need to
Press CHECK until the track you
don’t want appears in the display,
then press CLEAR.
Press CLEAR. Each time you
press the button, the last track will
be cleared.
Follow Steps 2 through 4 of the
programming procedure.
Hold down CLEAR until “ALL
CLr” appears in the display.
Create a new programme
following the programming
procedure.
Programming the CD tracks
(continued)
C-54 27.00C-46 23.00 C-60 30.00
- -. - - C-90 45.00
C-74 37.00
Playing CDs
13
GB
6 Start recording on the deck and then
press H on the player.
7 Reverse the tape to side B and press
H or X on the player to resume
playing the remaining tracks.
To cancel Time Edit
Press PLAY MODE.
Tips
• You can programme the tracks you want in
advance. Create a programme selecting the desired
tracks, then follow Steps 2 to 7. Be careful that the
total playing time of the programme does not
exceed the tape length of one side.
• You can set the tape length freely using
l AMS L.
Example:When the tape length of one side is 30
minutes and 15 seconds
1 To set the minutes, turn l AMS
L until “30” appears in the display,
then push l AMS L.
2 To set the seconds, turn l AMS
L until “15” appears in the display,
then push l AMS L.
• To check and change your programme, see pages 11
and 12.
Adjusting the Recording
Level (Peak Search)
The player locates the highest level among the
tracks to be recorded to let you adjust the
recording level before you start recording.
1 Before you start playing, press PEAK
SEARCH.
“PEAK” flashes in the display and the
player starts scanning the disc searching for
the highest peak level.
After scanning all the tracks, the player
repeats the portion with the highest peak
level.
2 Adjust the recording level on the deck.
3 Press x on the player to stop Peak
Search.
“PEAK” disappears from the display.
Notes
• The portion with the highest level may differ every
time you try the adjustment on the same disc. The
difference is, however, so slight that you won’t
find any problem in adjusting the recording level
precisely.
• Peak Search does not operate while you open the
disc tray by pressing the EX-CHANGE button.
Recording From CDs
14
GB
Additional Information
Precautions
On safety
• Caution — The use of optical instruments with this
product will increase eye hazard.
• Should any solid object or liquid fall into the
cabinet, unplug the player and have it checked by
qualified personnel before operating it any further.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
On power sources
• Before operating the player, check that the
operating voltage of the player is identical with
your local power supply. The operating voltage is
indicated on the nameplate at the rear of the player.
• The player is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the player itself has been turned off.
• If you are not going to use the player for a long
time, be sure to disconnect the player from the wall
outlet. To disconnect the AC power cord (mains
lead), grasp the plug itself; never pull the cord.
• AC power cord must be changed only at the
qualified service shop.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the player.
• Do not place the player on a soft surface such as a
rug that might block the ventilation holes on the
bottom.
• Do not place the player in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or mechanical shock.
On operation
• If the player is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lenses inside the
player. Should this occur, the player may not
operate properly. In this case, remove the disc and
leave the player turned on for about an hour until
the moisture evaporates.
On adjusting volume
• Do not turn up the volume while listening to a
portion with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level portion is played.
On cleaning
• Clean the cabinet, panel and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder, or solvent such as alcohol or
benzine.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
Notes on CDs
On handling CDs
• To keep the disc clean, handle the disc by its edge.
Do not touch the surface.
• Do not stick paper or tape on the disc.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, nor leave it in a car
parked in direct sunlight as there can be
considerable rise in temperature inside the car.
• Do not use any commercially available stabilizer. If
you do, the disc and the player may be damaged.
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning cloth.
Wipe the disc from the centre out.
• Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
Notes on CD-R/CD-RW playback
• Discs recorded on CD-R/CD-RW drives may not be
played back because of scratches, dirt, recording
condition, or the drive’s characteristics. Besides, the
discs, which are not yet finalized at the end of
recording, cannot be played back.
Additional Information
15
GB
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help you remedy the
problem. Should any problem persist, consult
your nearest Sony dealer.
There’s no sound.
• Check that the player is connected securely.
• Make sure you operate the amplifier correctly.
• Adjust the analog output level with ANALOG
OUT LEVEL +/– on the remote.
The CD does not play.
• There’s no CD inside the player. “no dISC”
appears. Insert a CD.
• Place the CD with the label side up on the disc
tray correctly.
• Clean the CD (see page 14).
• Moisture has condensed inside the player.
Remove the disc and leave the player turned on
for about an hour.
• Place the CD in the correct position on the disc
tray.
The recording level has changed.
• The recording level changes if you adjust the
analog output level with ANALOG OUT
LEVEL +/– on the remote during recording.
The remote does not function.
• Remove the obstacles in the path of the remote
and the player.
• Point the remote at the remote sensor on the
player.
• Replace all the batteries in the remote with new
ones if they are weak.
The player functions incorrectly.
• The microcomputer chips may be operating
incorrectly. Turn the power off, then turn it back
on to reset the player.
Specifications
Compact disc player
Laser Semiconductor laser (λ =
780 nm)
Emission duration:
continuous
Frequency response 2 Hz to 20 kHz ± 0.5 dB
Dynamic range More than 93 dB
Harmonic distortion Less than 0.0045%
Outputs
ANALOG
OUT
DIGITAL
OUT
(OPTICAL)
PHONES
General
Power requirements
Where purchased
Europe and some
Asian countries
Other countries
Power consumption 11 W
Dimensions (approx.) 430 x 110 x 400 mm
(w/h/d) incl. projecting parts
Mass (approx.) 5 kg
Supplied accessories
Audio cord (2 phono plugs – 2 phono plugs) (1)
Remote commander (remote) (1)
R6 (size AA) batteries (2)
Design and specifications are subject to change
without notice.
Load
impedance
Over 10
kilohms
Wave
length:
660 nm
32 ohms
Jack
type
Phono
jacks
Optical
output
connector
Stereo
phone
jack
Maximum
output level
2 V
(at 50 kilohms)
–18 dBm
10 mW
Load impedance
220 V - 230 V AC, 50/60 Hz
110 V - 120 V or 220 V - 240
V AC, adjustable, 50/60 Hz
2
FR
A propos de ce manuel
Les instructions contenues dans le présent mode
d’emploi concernent le modèle CDP-CE375.
Conseil
Les instructions de ce manuel décrivent les
commandes du lecteur.
Vous pouvez également utiliser les commandes de la
télécommande si elles portent les même noms que
celles du lecteur ou des noms similaires.
AVERTISSEMENT
Pour prévenir tout risque d’incendie ou
d’électrocution, gardez cet appareil à
l’abri de la pluie ou de l’humidité.
Pour prévenir tout risque d’électrocution, abstenez-
vous d’ouvrir le boîtier. Confiez l’entretien de votre
lecteur exclusivement à un personnel qualifié.
Cet appareil entre dans la catégorie des produits
LASER DE CLASSE 1. L’ETIQUETTE
INDIQUANT L’APPARTENANCE DE CE
LECTEUR A LA CLASSE 1 est apposée à l’arrière
du boîtier.
Ne jetez pas les piles aux
ordures. Portez-les à un
dépôt pour déchets
dangereux.
3
FR
Table des matières
Identification des pièces 4
Panneau avant .......................................................................................................................... 4
Panneau arrière ........................................................................................................................5
Télécommande ........................................................................................................................5
Préparation
Insertion de piles dans la télécommande .................................................................................6
Raccordement du système .......................................................................................................6
Lecture de CD
Chargement d’un CD............................................................................................................... 7
Lecture de CD –– Lecture normale/Lecture aléatoire/Lecture répétée ................................... 8
Utilisation de la fenêtre d’affichage CD..................................................................................9
Remplacement de disques en cours de lecture d’un disque ..................................................10
Programmation des pistes du CD .......................................................................................... 11
Fondu enchaîné......................................................................................................................12
Enregistrement de CD
Enregistrement d’un CD en spécifiant la longueur de la bande (Time Edit) ........................12
Réglage du niveau d'enregistrement (Recherche de crête).................................................... 13
Informations complémentaires
Précautions ............................................................................................................................14
Remarques sur les CD ........................................................................................................... 14
Dépannage .............................................................................................................................15
Spécifications ........................................................................................................................15
FRFR
4
FR
Capteur de la télécommande qh (6)
CHECK w; (11, 12)
CLEAR 9 (11, 12)
DISC 1–5 2 (8, 9, 11)
Compartiment à disques qj (7)
DISC SKIP 8 (7, 10, 12)
Fenêtre d’affichage 3 (9)
EX-CHANGE 7 (10, 13)
FADER qd (12)
PEAK SEARCH qs (13)
PLAY MODE qa (8, 9, 11, 13)
Prise PHONES wa (9)
POWER 1 (7)
REPEAT qf (8)
TIME qg (9, 10)
TIME EDIT ql (12)
Identification des pièces
Panneau avant
Les éléments sont classés par ordre alphabétique.
Reportez-vous aux pages indiquées entre parenthèses ( ) pour plus de détails.
DESCRIPTIONS DES
TOUCHES
A OPEN/CLOSE ws (7, 9)
H 4 (8, 11, 13)
X 5 (9, 13)
x 6 (9, 13)
Molette lAMSL 0 (9, 11,
13)
m/M qk (9, 12)
5
FR
Panneau arrière
Télécommande
Identification des pi
èces
5
FR
Câble secteur 3 (6)
Prises ANALOG OUT L/R 2 (6)
Prise DIGITAL OUT OPTICAL 1 (7)
ANALOG OUT LEVEL +/– qs
(6, 7)
CONTINUE 2 (8)
DISC SKIP 9 (7, 10, 12)
PROGRAM 8 (8)
REPEAT 3 (8)
SHUFFLE 1 (8)
TIME 0 (9, 10)
DESCRIPTIONS DES
TOUCHES
N 5 (8, 11, 13)
X 4 (9, 13)
x qa (9, 13)
. AMS > 6 (9, 11, 13)
m/M 7 (9, 12)
6
FR
Préparation
Insertion de piles dans la
télécommande
Vous pouvez commander le lecteur à l’aide de
la télécommande fournie.
Insérez deux piles R6 (AA) en faisant
correspondre les signes + et – des piles avec le
schéma situé à l’intérieur du compartiment.
Commencez par insérer le pôle négatif (–), puis
appuyez sur la pile jusqu’à ce que le pôle
positif (+) s’encliquette.
Lorsque vous utilisez la télécommande,
dirigez-la vers le capteur
du lecteur.
Conseil
Lorsque la télécommande ne fonctionne plus,
remplacez les deux piles par des piles neuves.
Remarque
• Ne laissez pas la télécommande dans un endroit
extrêmement chaud ou humide.
• Ne laissez pas tomber de corps étrangers dans le
boîtier de la télécommande, notamment lorsque
vous changez les piles.
• N’exposez pas le capteur de télécommande
directement aux rayons du soleil ou à des
équipements d’éclairage. Sinon, vous risquez de
déclencher un dysfonctionnement de l’appareil.
• Si vous n’utilisez la télécommande pendant une
période prolongée, retirez les piles pour éviter les
dommages dus à la fuite des piles ou à la
corrosion.
Raccordement du système
Raccordements
Cette section décrit comment raccorder le
lecteur CD à un amplificateur. Assurez-vous
que vous avez mis les deux appareils hors
tension avant de procéder aux raccordements.
Conseil
Vous pouvez régler le niveau de sortie analogique de
l’amplificateur à l’aide de la télécommande livrée
avec l’appareil.
Appuyez sur ANALOG OUT LEVEL +/– sur la
télécommande. Vous pouvez réduire le niveau de
sortie jusqu’à – 20 dB.
Lorsque vous réduisez le niveau de sortie analogique,
l’indication “FADE” apparaît dans la fenêtre
d’affichage.
Lorsque vous mettez le lecteur hors tension, le niveau
de sortie analogique revient automatiquement au
niveau maximum.
Réglage du sélecteur de tension
(modèles équipés d’un sélecteur
de tension uniquement)
Vérifiez si le sélecteur de tension sur le panneau arrière
du lecteur est réglé sur la tension secteur locale. Si ce
n’est pas le cas, réglez le sélecteur sur la position
appropriée à l’aide d’un tournevis avant de brancher le
cordon d’alimentation sur une prise murale.
Lecteur CD
Entrée audio
(blanc) (L)
: Sens du signal
Amplificateur
Vers le
secteur
Vers le
secteur
Entrée audio
(rouge) (R)
ANALOG
OUT
(rouge) (R)
ANALOG OUT
(blanc) (L)
110 - 120 V220 - 240 V
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
