Sony CDP-CE375 ユーザーマニュアル

Compact Disc

Player

4-233-300-51(2)

CDP-CE375

Operating Instructions

Mode d’emploi

Manual de instrucciones

FR

ES

FR

GB

FR

ES

FR

CT

2

GB

About this manual

The instructions in this manual is for CDP-CE375.

Tip

Instructions in this manual describe the controls on

the player.

You can also use the controls on the remote if they

have the same or similar names as those on the

player.

WARNING

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualified personnel only.

This appliance is classified as a CLASS 1 LASER

product. The CLASS 1 LASER PRODUCT

MARKING is located on the rear exterior.

AC power cord must be changed only at the qualified

service shop.

Do not install the appliance in a confined space, such

as a bookcase or built-in cabinet.

To prevent fire, do not Cover the ventilation of the

apparatus with news papers, table-cloths, curtains,

etc. And don’t place lighted candles on the apparatus.

To prevent fire or shock hazard, do not place objects

filled with liquids, such as vases, on the apparatus.

Don’ throw a battery, this pose

it as the injurious wastes.

3

GB

Table of Contents

Parts Identification 4

Front Panel ..............................................................................................................................4

Rear Panel................................................................................................................................5

Remote Control ....................................................................................................................... 5

Getting Started

Inserting Batteries Into the Remote Control............................................................................6

Hooking Up the System ..........................................................................................................6

Playing CDs

Loading the CD ....................................................................................................................... 7

Playing the CD –– Normal Play/Shuffle Play/Repeat Play..................................................... 8

Using the CD display ..............................................................................................................9

Replacing Discs While Playing a Disc ..................................................................................10

Programming the CD tracks ..................................................................................................11

Fading In or Out ....................................................................................................................12

Recording From CDs

Recording a CD by Specifying Tape Length (Time Edit).....................................................12

Adjusting the Recording Level (Peak Search) ......................................................................13

Additional Information

Precautions ............................................................................................................................14

Notes on CDs......................................................................................................................... 14

Troubleshooting..................................................................................................................... 15

Specifications ........................................................................................................................15

FRGB

4

GB

CHECK w; (11, 12)

CLEAR 9 (11, 12)

DISC 1–5 2 (8, 9, 11)

Disc compartment qj (7)

DISC SKIP 8 (7, 10, 12)

Display 3 (9)

EX-CHANGE 7 (10, 13)

FADER qd (12)

PEAK SEARCH qs (13)

PHONES jack wa (9)

PLAY MODE qa (8, 9, 11, 13)

POWER 1 (7)

Remote sensor qh (6)

REPEAT qf (8)

TIME qg (9, 10)

TIME EDIT ql (12)

Parts Identification

Front Panel

The items are arranged in alphabetical order.

Refer to the pages indicated in parentheses ( ) for details.

BUTTON DESCRIPTIONS

A OPEN/CLOSE ws (7, 9)

H 4 (8, 11, 13)

X 5 (9, 13)

x 6 (9, 13)

lAMSL dial 0 (9, 11, 13)

m/M qk (9, 12)

5

GB

Rear Panel

Remote Control

Parts Identification

5

GB

ANALOG OUT L/R jacks 2 (6)

DIGITAL OUT OPTICAL jack 1 (7)

Mains lead 3 (6)

ANALOG OUT LEVEL +/– qs

(6, 7)

CONTINUE 2 (8)

DISC SKIP 9 (7, 10, 12)

PROGRAM 8 (8)

REPEAT 3 (8)

SHUFFLE 1 (8)

TIME 0 (9, 10)

BUTTON DESCRIPTIONS

N 5 (8, 11, 13)

X 4 (9, 13)

x qa (9, 13)

. AMS > 6 (9, 11, 13)

m/M 7 (9, 12)

6

GB

Getting Started

Inserting Batteries Into

the Remote Control

You can control the player using the supplied

remote.

Insert two R6 (size AA) batteries by matching

the + and – on the batteries to the diagram

inside the battery compartment.

Insert the negative (–) end first, then push in

and down until the positive (+) end clicks into

position.

When using the remote, point it at the remote

sensor

on the player.

Tip

When the remote no longer operates the system,

replace both batteries with new ones.

Note

• Do not leave the remote near an extremely hot or

humid place.

• Do not drop any foreign object into the remote

casing, particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight

or lighting apparatuses. Doing so may cause a

malfunction.

• If you don’t use the remote for an extended period

of time, remove the batteries to avoid possible

damage from battery leakage and corrosion.

Hooking Up the System

Hookups

This section describes how to hook up the CD

player to an amplifier. Be sure to turn off the

power of each component before making the

connections.

Tip

You can adjust the analog output level to the

amplifier using the remote comes with this player.

Press ANALOG OUT LEVEL +/– on the remote.

You can reduce the output level up to –20 dB.

When you reduce the analog output level, “FADE”

appears in the display.

When you turn off the player, the analog output level

automatically returns to the maximum level.

Setting the voltage selector

(voltage selector equipped

models only)

Check that the voltage selector on the rear

panel of the player is set to the local power line

voltage. If not, set the selector to the correct

position using a screwdriver before connecting

the AC power cord to a wall outlet.

CD player

Audio input

(White) (L)

: Signal flow

Amplifier

To mains

Audio input

(Red) (R)

ANALOG

OUT

(Red) (R)

ANALOG OUT

(White) (L)

110 - 120 V220 - 240 V

Getting Started

7

GB

Making digital hookups

If you have a digital component such as a

digital amplifier, D/A converter, DAT, or MD,

connect the component via the DIGITAL OUT

(OPTICAL) connector using the optical cable

(not supplied). Take off the cap and plug in the

optical cable.

Note that you cannot use the following

functions when making this connection:

• Fading In or Out (see page 12)

• Adjusting the output level using the

ANALOG OUT LEVEL +/– buttons on the

remote

Note

When you connect via the DIGITAL OUT

(OPTICAL) connector, noise may occur when you

play CD software other than music, such as a CD-

ROM.

Transporting the player

Before transporting the player, follow the

procedure below to return the internal

mechanisms back to their original position.

1 Remove all the discs from the disc tray.

2 Press A OPEN/CLOSE to close the

disc tray.

“no dISC” appears in the display.

3 Wait for 10 seconds, then press

POWER to turn off the player.

POC-15

Optical cable (not supplied)

Digital component

CD player

Loading a CD

1 Turn on the amplifier and select the CD

player position so that you can listen to

the sound from this player.

2 Press POWER to turn on the player.

3 Press AOPEN/CLOSE.

The disc compartment slides out.

4 Place a disc on the disc tray with the

label side up.

5 To place other discs, press DISC SKIP

and place the discs in the order you

want to play.

Each time you press the button, the disc tray

turns and you can place the discs in the

empty disc compartments. The player plays

the disc in front of you first.

6 Press AOPEN/CLOSE to close the disc

compartment.

Playing CDs

When you play a CD single,

place it on the inner circle

of the tray.

Disc number

Playing CDs

DIGITAL

OUT

OPTICAL

DIGITAL

INPUT

OPTICAL

8

GB

Repeat Play Operations

You can play the CD tracks repeatedly in any

play modes.

To activate the Repeat Play function, press

REPEAT until “REPEAT’ appears in the

display.

To

Repeat only one track

Cancel Repeat Play

When you are in the Repeat Play function, the

player repeats the tracks as follows:

When the disc is

played in

Continuous Play

(ALL DISCS)

Continuous Play

(1 DISC)

Shuffle Play

(ALL DISCS)

Shuffle Play

(1 DISC)

Programme Play

(page 11)

Playing the CD

––Normal Play/Shuffle Play/Repeat

Play

This unit lets you play the CD in different play

modes.

1 Press PLAY MODE repeatedly until the

mode you want appears.

2 Press H.

Tips

• You can select the disc you want to start playing

first by pressing one of the DISC 1 – 5 buttons.

• You can specify discs during ALL DISCS Shuffle

Play mode, and the tracks on the specified discs are

played in a random order.

Press DISC 1 – 5 to specify the discs after Step 1.

Semi-circles appear around the specified disc

numbers in the display. To cancel the selected discs,

press DISC 1 – 5 again. The semi-circles disappear.

To return to ALL DISCS Shuffle Play, press PLAY

MODE until “ALL DISCS SHUFFLE” appears in

the display.

• You can select the playing mode by pressing

CONTINUE, SHUFFLE, or PROGRAM on the

remote.

Select

ALL DISCS

(Continuous

Play)

1 DISC

(Continuous

Play)

ALL DISCS

SHUFFLE

1 DISC

SHUFFLE

PROGRAM

To play

All discs in the player

consecutively in the order of disc

number.

Only the disc you’ve selected.

All tracks on all discs in random

order.

All tracks on the specific disc in

random order.

The tracks on the CD in the

order you want them to be

played (see “Programming the

CD tracks” on page 11).

Press REPEAT

Until “REPEAT 1” appears

while playing the track you

want to repeat.

Until “REPEAT” or

“REPEAT 1” disappears.

The player repeats

All the tracks on all discs

All the tracks on the current

disc

All the tracks on all discs in

random order

All the tracks on the current

disc in random order

The same programme

Playing CDs

9

GB

Other Operations

To

Stop playback

Pause

Select a track

Go to the next disc

Select a disc directly

Find a point in a track

Play tracks in random

order

Remove the CD

Adjust the volume

Tips

• You can adjust the analog output level with the

ANALOG OUT LEVEL +/– on the remote (page

6).

• You can adjust the headphones volume on the

remote. To adjust the volume, connect the

headphones to the PHONES jack and adjust the

volume with the ANALOG OUT LEVEL +/– on

the remote.

• If there is no CD in the player, “no dISC” appears

in the display.

Notes

• If “ ” appears in the display, the disc has

reached the end while you were pressing M. Press

m or turn lAMSL counterclockwise to go

back.

• If you press ANALOG OUT LEVEL buttons on the

remote while recording, the recording level will

change even when it is preset on the tape deck, etc.

Using the CD display

You can check information about the disc using

the display.

In the stop mode

Press TIME.

The display shows the current disc number, the

total number of tracks, total playing time and

music calendar.

The information also appears when you press

AOPEN/CLOSE to close the disc tray.

The tracks numbered over 20 cannot be

displayed in the music calendar.

Notes on the disc number

indications

• The red circle around a disc number

indicates the disc is ready to be played.

• When all the tracks on a disc have been

played, the semi-circle around the disc

number disappears.

• When a disc compartment is recognized as

empty, the semi-circled disc number

disappears.

During normal playback

While playing a disc, the display shows the

current disc number, track number, playing

time of the track and the music calendar.

The track numbers in the music calendar

disappear after they are played.

Do this

Press x.

Press X. Press X again or

H to resume play.

During play or pause, turn

lAMSL clockwise

(to go forward) or

counterclockwise (to go

backward)

(or press >( to go

forward) or . (to go

backward) on the remote).

Press DISC SKIP.

Press DISC 1 – 5.

Press and hold M or m

during playback, and

release at the desired point.

Press PLAY MODE until

“SHUFFLE” appears in the

display.

Press AOPEN/CLOSE.

Press ANALOG OUT

LEVEL +/– on the remote.

Total number of tracks

Music calendar

Total playing time

Current disc number

continued

12345

678910

1 2 3 4 5

DISCSALL

TRACK

DISC

MIN

SEC

110 45 28

10

GB

To check the remaining time

Press TIME during playback.

Each time you press this button while playing a

disc, the display changes as shown in the chart

below.

Playing time and number on the current track

t Remaining time on the current track t

Remaining time on the disc

Notes

• When the disc has more than 24 tracks, “– – . ––”

appears instead of the remaining time.

• The remaining time on the disc appears only when

the disc is played in Continuous Play.

Replacing Discs While

Playing a Disc

You can open the disc tray while playing a disc

so that you can check what discs are to be

played next and replace discs without

interrupting playback of the current disc.

1Press EX-CHANGE.

The disc tray opens and two disc

compartments appear. Even if the player is

playing a disc, it doesn’t stop playing.

2Replace discs in the compartments

with new ones.

The player plays the disc on the left side

compartment after the current disc, and then

the one on the right side compartment.

3Press DISC SKIP.

The disc tray turns and other two disc

compartments appear.

4Replace discs in the compartments

with new ones.

5Press EX-CHANGE.

The disc tray closes.

While the disc tray is open by

pressing the EX-CHANGE button

• If the playback of the current disc ends, the

player stops playing. If the disc is played in

1 DISC Repeat Play mode (see page 8), the

current disc starts playing again.

• In ALL DISCS Shuffle Play mode (see page

8), tracks are reshuffled on the current disc.

• In Programme Play mode (see page 11), only

the tracks on the current disc are played.

• Do not push the disc tray to close it in

Step 5, as you may damage the

player.

Using the CD display (continued)

Playing CDs

11

GB

Programming the CD

tracks

You can arrange the order of the tracks on the

discs and create your own programme. The

programme can contain up to 32 “steps” — one

“step” may contain a track or a whole disc.

1 Press PLAY MODE repeatedly until

“PROGRAM” appears in the display

before you start playing.

If a programme is already stored, the last

step of the programme appears in the

display. When you want to erase the whole

programme, hold down CLEAR until “ALL

CLr” appears in the display (see page 12).

2 Press DISC 1 – 5 to select the disc.

“AL” in the display stands for “all” tracks.

When you want to programme the whole

disc as one step, skip Step 3, and go to Step

4.

3 Turn lAMSL until the track you

want appears and push lAMSL to

select the track.

The track number that you programmed, the

playing order, and the total playing time

appear in the display.

If you’ve made a mistake

Press CLEAR, then repeat Step 2.

4 To programme other discs or tracks, do

the following:

5 Press H to start Programme Play.

To cancel Programme Play

Press PLAY MODE.

Tips

• You can create your programme while checking the

disc labels.

While the disc tray is open, follow Steps 1 to 4 with

pressing the DISC SKIP button to check the disc

labels. If you close the disc tray before Step 5, the

total playing time appears in the display after a

while.

Note that, if the programmed track number isn’t

found on the disc, that step is automatically erased.

• The programme remains even after the Programme

Play ends. When you press the H button, you can

play the same programme again.

• The programme remains until you erase it or turn

off the player. If you replace discs, the programmed

disc and track numbers remain. So, the player plays

only the existing disc and track numbers. However,

the disc and track numbers that aren’t found in the

player or on the disc are deleted from the

programme, and the rest of the programme is played

in the programmed order.

• For the recording to the A side or B side of the

cassette tape, you can pause Programme Play.

Note

The total playing time doesn’t appear when:

—You have programmed a track whose number

exceeds 20.

—The total playing time of the programme exceeds

200 minutes.

Checking the track order

You can check your programme before or after

you start playing.

Press CHECK.

Each time you press this button, the display

shows the track (the disc and track numbers) or

the disc (the disc number and “AL” indication)

of each step in the programmed order. After the

last step in the programme, the display shows

“End” and returns to the original display. If you

check the order after you start playing, the

display shows only the remaining steps.

To programme

Other discs

Other tracks on the

same disc

Other tracks on

other discs

Repeat Step(s)

2

3

2 and 3

continued

12

GB

Changing the track order

You can change your programme before you

start playing.

To

Erase a track

Erase the last track

in the programme

Add tracks to the

end of the

programme

Change the whole

programme

completely

Fading In or Out

You can manually fade in or out to prevent

tracks from starting or ending abruptly.

Note that you cannot use this effect when you

use the DIGITAL OUT (OPTICAL) connector.

To

Start play fading in

End play fading out

Fading time lasts for 5 seconds.

Press FADER

During pause. “FADE” flashes.

The play fades in.

When you want to start fading

out. “FADE” flashes. Then play

fades out and the player pauses.

Recording From CDs

Recording a CD by

Specifying Tape Length

(Time Edit)

You can have the player create a programme

that will fit the length of the tape.

The player automatically creates a programme,

keeping the original order of the disc.

The programme can contain up to 32 steps (a

pause inserted between steps is counted as one

step).

Note that tracks numbered over 20 cannot be

programmed automatically.

1Press DISC SKIP to select the disc.

2Press TIME EDIT repeatedly before you

start playing until “EDIT” appears and

“A” in the

A

indication flashes in the

display.

3Press m or M to specify the tape

length.

Each time you press these buttons, the

display changes as shown below, with the

tape length of one side following each

indication.

4Press TIME EDIT to have the player

create the programme.

The display shows the tracks to be recorded.

“B” in the

AB

indication flashes in the

display.

5When you record on both sides of the

tape, press TIME EDIT again.

The player inserts a pause, then creates the

programme for side B. The display shows

the programmed tracks.

When you record on one side of the tape,

skip this step.

You need to

Press CHECK until the track you

don’t want appears in the display,

then press CLEAR.

Press CLEAR. Each time you

press the button, the last track will

be cleared.

Follow Steps 2 through 4 of the

programming procedure.

Hold down CLEAR until “ALL

CLr” appears in the display.

Create a new programme

following the programming

procedure.

Programming the CD tracks

(continued)

C-54 27.00C-46 23.00 C-60 30.00

- -. - - C-90 45.00

C-74 37.00

Playing CDs

13

GB

6 Start recording on the deck and then

press H on the player.

7 Reverse the tape to side B and press

H or X on the player to resume

playing the remaining tracks.

To cancel Time Edit

Press PLAY MODE.

Tips

• You can programme the tracks you want in

advance. Create a programme selecting the desired

tracks, then follow Steps 2 to 7. Be careful that the

total playing time of the programme does not

exceed the tape length of one side.

• You can set the tape length freely using

l AMS L.

Example:When the tape length of one side is 30

minutes and 15 seconds

1 To set the minutes, turn l AMS

L until “30” appears in the display,

then push l AMS L.

2 To set the seconds, turn l AMS

L until “15” appears in the display,

then push l AMS L.

• To check and change your programme, see pages 11

and 12.

Adjusting the Recording

Level (Peak Search)

The player locates the highest level among the

tracks to be recorded to let you adjust the

recording level before you start recording.

1 Before you start playing, press PEAK

SEARCH.

“PEAK” flashes in the display and the

player starts scanning the disc searching for

the highest peak level.

After scanning all the tracks, the player

repeats the portion with the highest peak

level.

2 Adjust the recording level on the deck.

3 Press x on the player to stop Peak

Search.

“PEAK” disappears from the display.

Notes

• The portion with the highest level may differ every

time you try the adjustment on the same disc. The

difference is, however, so slight that you won’t

find any problem in adjusting the recording level

precisely.

• Peak Search does not operate while you open the

disc tray by pressing the EX-CHANGE button.

Recording From CDs

14

GB

Additional Information

Precautions

On safety

• Caution — The use of optical instruments with this

product will increase eye hazard.

• Should any solid object or liquid fall into the

cabinet, unplug the player and have it checked by

qualified personnel before operating it any further.

• Discs with non-standard shapes (e.g., heart, square,

star) cannot be played on this unit. Attempting to do

so may damage the unit. Do not use such discs.

On power sources

• Before operating the player, check that the

operating voltage of the player is identical with

your local power supply. The operating voltage is

indicated on the nameplate at the rear of the player.

• The player is not disconnected from the AC power

source (mains) as long as it is connected to the wall

outlet, even if the player itself has been turned off.

• If you are not going to use the player for a long

time, be sure to disconnect the player from the wall

outlet. To disconnect the AC power cord (mains

lead), grasp the plug itself; never pull the cord.

• AC power cord must be changed only at the

qualified service shop.

On placement

• Place the player in a location with adequate

ventilation to prevent heat build-up in the player.

• Do not place the player on a soft surface such as a

rug that might block the ventilation holes on the

bottom.

• Do not place the player in a location near heat

sources, or in a place subject to direct sunlight,

excessive dust or mechanical shock.

On operation

• If the player is brought directly from a cold to a

warm location, or is placed in a very damp room,

moisture may condense on the lenses inside the

player. Should this occur, the player may not

operate properly. In this case, remove the disc and

leave the player turned on for about an hour until

the moisture evaporates.

On adjusting volume

• Do not turn up the volume while listening to a

portion with very low level inputs or no audio

signals. If you do, the speakers may be damaged

when a peak level portion is played.

On cleaning

• Clean the cabinet, panel and controls with a soft

cloth slightly moistened with a mild detergent

solution. Do not use any type of abrasive pad,

scouring powder, or solvent such as alcohol or

benzine.

If you have any questions or problems

concerning your player, please consult your

nearest Sony dealer.

Notes on CDs

On handling CDs

• To keep the disc clean, handle the disc by its edge.

Do not touch the surface.

• Do not stick paper or tape on the disc.

• Do not expose the disc to direct sunlight or heat

sources such as hot air ducts, nor leave it in a car

parked in direct sunlight as there can be

considerable rise in temperature inside the car.

• Do not use any commercially available stabilizer. If

you do, the disc and the player may be damaged.

• After playing, store the disc in its case.

On cleaning

• Before playing, clean the disc with a cleaning cloth.

Wipe the disc from the centre out.

• Do not use solvents such as benzine, thinner,

commercially available cleaners or anti-static spray

intended for vinyl LPs.

Notes on CD-R/CD-RW playback

• Discs recorded on CD-R/CD-RW drives may not be

played back because of scratches, dirt, recording

condition, or the drive’s characteristics. Besides, the

discs, which are not yet finalized at the end of

recording, cannot be played back.

Additional Information

15

GB

Troubleshooting

If you experience any of the following

difficulties while using the player, use this

troubleshooting guide to help you remedy the

problem. Should any problem persist, consult

your nearest Sony dealer.

There’s no sound.

• Check that the player is connected securely.

• Make sure you operate the amplifier correctly.

• Adjust the analog output level with ANALOG

OUT LEVEL +/– on the remote.

The CD does not play.

• There’s no CD inside the player. “no dISC”

appears. Insert a CD.

• Place the CD with the label side up on the disc

tray correctly.

• Clean the CD (see page 14).

• Moisture has condensed inside the player.

Remove the disc and leave the player turned on

for about an hour.

• Place the CD in the correct position on the disc

tray.

The recording level has changed.

• The recording level changes if you adjust the

analog output level with ANALOG OUT

LEVEL +/– on the remote during recording.

The remote does not function.

• Remove the obstacles in the path of the remote

and the player.

• Point the remote at the remote sensor on the

player.

• Replace all the batteries in the remote with new

ones if they are weak.

The player functions incorrectly.

• The microcomputer chips may be operating

incorrectly. Turn the power off, then turn it back

on to reset the player.

Specifications

Compact disc player

Laser Semiconductor laser (λ =

780 nm)

Emission duration:

continuous

Frequency response 2 Hz to 20 kHz ± 0.5 dB

Dynamic range More than 93 dB

Harmonic distortion Less than 0.0045%

Outputs

ANALOG

OUT

DIGITAL

OUT

(OPTICAL)

PHONES

General

Power requirements

Where purchased

Europe and some

Asian countries

Other countries

Power consumption 11 W

Dimensions (approx.) 430 x 110 x 400 mm

(w/h/d) incl. projecting parts

Mass (approx.) 5 kg

Supplied accessories

Audio cord (2 phono plugs – 2 phono plugs) (1)

Remote commander (remote) (1)

R6 (size AA) batteries (2)

Design and specifications are subject to change

without notice.

Load

impedance

Over 10

kilohms

Wave

length:

660 nm

32 ohms

Jack

type

Phono

jacks

Optical

output

connector

Stereo

phone

jack

Maximum

output level

2 V

(at 50 kilohms)

–18 dBm

10 mW

Load impedance

220 V - 230 V AC, 50/60 Hz

110 V - 120 V or 220 V - 240

V AC, adjustable, 50/60 Hz

2

FR

A propos de ce manuel

Les instructions contenues dans le présent mode

d’emploi concernent le modèle CDP-CE375.

Conseil

Les instructions de ce manuel décrivent les

commandes du lecteur.

Vous pouvez également utiliser les commandes de la

télécommande si elles portent les même noms que

celles du lecteur ou des noms similaires.

AVERTISSEMENT

Pour prévenir tout risque d’incendie ou

d’électrocution, gardez cet appareil à

l’abri de la pluie ou de l’humidité.

Pour prévenir tout risque d’électrocution, abstenez-

vous d’ouvrir le boîtier. Confiez l’entretien de votre

lecteur exclusivement à un personnel qualifié.

Cet appareil entre dans la catégorie des produits

LASER DE CLASSE 1. L’ETIQUETTE

INDIQUANT L’APPARTENANCE DE CE

LECTEUR A LA CLASSE 1 est apposée à l’arrière

du boîtier.

Ne jetez pas les piles aux

ordures. Portez-les à un

dépôt pour déchets

dangereux.

3

FR

Table des matières

Identification des pièces 4

Panneau avant .......................................................................................................................... 4

Panneau arrière ........................................................................................................................5

Télécommande ........................................................................................................................5

Préparation

Insertion de piles dans la télécommande .................................................................................6

Raccordement du système .......................................................................................................6

Lecture de CD

Chargement d’un CD............................................................................................................... 7

Lecture de CD –– Lecture normale/Lecture aléatoire/Lecture répétée ................................... 8

Utilisation de la fenêtre d’affichage CD..................................................................................9

Remplacement de disques en cours de lecture d’un disque ..................................................10

Programmation des pistes du CD .......................................................................................... 11

Fondu enchaîné......................................................................................................................12

Enregistrement de CD

Enregistrement d’un CD en spécifiant la longueur de la bande (Time Edit) ........................12

Réglage du niveau d'enregistrement (Recherche de crête).................................................... 13

Informations complémentaires

Précautions ............................................................................................................................14

Remarques sur les CD ........................................................................................................... 14

Dépannage .............................................................................................................................15

Spécifications ........................................................................................................................15

FRFR

4

FR

Capteur de la télécommande qh (6)

CHECK w; (11, 12)

CLEAR 9 (11, 12)

DISC 1–5 2 (8, 9, 11)

Compartiment à disques qj (7)

DISC SKIP 8 (7, 10, 12)

Fenêtre d’affichage 3 (9)

EX-CHANGE 7 (10, 13)

FADER qd (12)

PEAK SEARCH qs (13)

PLAY MODE qa (8, 9, 11, 13)

Prise PHONES wa (9)

POWER 1 (7)

REPEAT qf (8)

TIME qg (9, 10)

TIME EDIT ql (12)

Identification des pièces

Panneau avant

Les éléments sont classés par ordre alphabétique.

Reportez-vous aux pages indiquées entre parenthèses ( ) pour plus de détails.

DESCRIPTIONS DES

TOUCHES

A OPEN/CLOSE ws (7, 9)

H 4 (8, 11, 13)

X 5 (9, 13)

x 6 (9, 13)

Molette lAMSL 0 (9, 11,

13)

m/M qk (9, 12)

5

FR

Panneau arrière

Télécommande

Identification des pi

èces

5

FR

Câble secteur 3 (6)

Prises ANALOG OUT L/R 2 (6)

Prise DIGITAL OUT OPTICAL 1 (7)

ANALOG OUT LEVEL +/– qs

(6, 7)

CONTINUE 2 (8)

DISC SKIP 9 (7, 10, 12)

PROGRAM 8 (8)

REPEAT 3 (8)

SHUFFLE 1 (8)

TIME 0 (9, 10)

DESCRIPTIONS DES

TOUCHES

N 5 (8, 11, 13)

X 4 (9, 13)

x qa (9, 13)

. AMS > 6 (9, 11, 13)

m/M 7 (9, 12)

6

FR

Préparation

Insertion de piles dans la

télécommande

Vous pouvez commander le lecteur à l’aide de

la télécommande fournie.

Insérez deux piles R6 (AA) en faisant

correspondre les signes + et – des piles avec le

schéma situé à l’intérieur du compartiment.

Commencez par insérer le pôle négatif (–), puis

appuyez sur la pile jusqu’à ce que le pôle

positif (+) s’encliquette.

Lorsque vous utilisez la télécommande,

dirigez-la vers le capteur

du lecteur.

Conseil

Lorsque la télécommande ne fonctionne plus,

remplacez les deux piles par des piles neuves.

Remarque

• Ne laissez pas la télécommande dans un endroit

extrêmement chaud ou humide.

• Ne laissez pas tomber de corps étrangers dans le

boîtier de la télécommande, notamment lorsque

vous changez les piles.

• N’exposez pas le capteur de télécommande

directement aux rayons du soleil ou à des

équipements d’éclairage. Sinon, vous risquez de

déclencher un dysfonctionnement de l’appareil.

• Si vous n’utilisez la télécommande pendant une

période prolongée, retirez les piles pour éviter les

dommages dus à la fuite des piles ou à la

corrosion.

Raccordement du système

Raccordements

Cette section décrit comment raccorder le

lecteur CD à un amplificateur. Assurez-vous

que vous avez mis les deux appareils hors

tension avant de procéder aux raccordements.

Conseil

Vous pouvez régler le niveau de sortie analogique de

l’amplificateur à l’aide de la télécommande livrée

avec l’appareil.

Appuyez sur ANALOG OUT LEVEL +/– sur la

télécommande. Vous pouvez réduire le niveau de

sortie jusqu’à – 20 dB.

Lorsque vous réduisez le niveau de sortie analogique,

l’indication “FADE” apparaît dans la fenêtre

d’affichage.

Lorsque vous mettez le lecteur hors tension, le niveau

de sortie analogique revient automatiquement au

niveau maximum.

Réglage du sélecteur de tension

(modèles équipés d’un sélecteur

de tension uniquement)

Vérifiez si le sélecteur de tension sur le panneau arrière

du lecteur est réglé sur la tension secteur locale. Si ce

n’est pas le cas, réglez le sélecteur sur la position

appropriée à l’aide d’un tournevis avant de brancher le

cordon d’alimentation sur une prise murale.

Lecteur CD

Entrée audio

(blanc) (L)

: Sens du signal

Amplificateur

Vers le

secteur

Vers le

secteur

Entrée audio

(rouge) (R)

ANALOG

OUT

(rouge) (R)

ANALOG OUT

(blanc) (L)

110 - 120 V220 - 240 V

ページが読み込まれています...

Sony CDP-CE375 ユーザーマニュアル

このマニュアルも適しています

Sony CDP-CE375 ユーザーマニュアル

他の言語で

関連論文

その他のドキュメント