1.The product and the accessories are assembled and tightened by
the ball head nut (compatible with other ball head diameter 17mm)
and fixed in the suitable position of the car. Connect the product
with QC3.0 car charger or ≥PD18W car charger (optional) by cable,
and insert it into cigarette lighter .
2.After power on, the indicator light is always on, and it can
automatically detect whether there is a mobile phone on the
product:
1 When there’s a phone on it, the clamping arms hold the phone
in a constant state.
2 Without a phone on it, the product will automatically open its
arms and bottom support within 5 seconds to wait for the phone to
be put upon it. When the mobile phone is placed on the product,
the bottom support holds the mobile phone, the wireless charging
coil will sense the metal parts of the mobile phone through the
FOD, depending on the size of the phone, the bottom holder and
the clamp-arms move simultaneously to the center of the coil, to
automatically clamp the phone and charge it (if the phone has a
wireless charging function) , because the ratio of length to width of
the phone is basically the same, so the positions of the charging
coil and the receiving coil are automatically aligned relative to each
other. The charging efficiency can be ensured without adjusting the
base support manually.
1、把该产品与配件通过球头螺帽装配并旋紧（可兼容其他球头直径
17mm配件），并固定在汽车合适位置。用数据线把产品与QC3.0车
充或PD18W及以上车充（选配）连接，并插入点烟器处取电。
2、该产品通电后，指示灯常亮，自动检测本产品上是否有手机 :
1 有手机时，夹臂夹紧手机的状态不变。
2 没有手机,5秒内自动张开左右夹臂和底托等待需充电的手机放入，
当手机放在产品上，底托托住手机，无线充线圈会通过FOD感应到手
机的金属部件，并根据不同手机的尺寸，底托和左右夹子同时向线圈
中心移动自动夹紧手机并对手机无线充电（如果手机具备无线充功能
），因为手机的长宽比例基本一致，所以充电线圈和接收线圈的位置
都是相对重叠自动对齐。在无需调节底托的情况下保证了充电效率。
（本产品双线圈版本支持给三星Z-FILP翻盖手机充电）
3、产品无线充电启动时指示灯呼吸；如果手机不支持无线充电，指
示灯闪烁5S熄灭，（有可能部分没有无线充功能的手机本产品感应不
到，需要按按键夹紧手机）。
4、为了保证充电的效率和稳定性，无线充的最佳距离是4mm以内
并不能穿透金属，所以需要避免用金属的或太厚的手机保护壳，这
1左夹臂
2右夹臂
3底托
4无线充线圈/指示灯
5无线充线圈区域
6按钮
7Type-C 充电口
8螺帽
产品介绍 亮灯模式
使用说明
产品细节
包装清单
模式
通电
待机
充电
充满
检测到异物
产品参数
产品名称：X3
工作频率：115K-205KHZ
推荐充电距离：≤4mm
输 入：5V/2A, 9V/2A
输出功率：5W/7.5W/10W/15W(MAX)
适用手机：4.0-6.9英寸
产品尺寸：97.5*62*20.5mm
净 重：155.5g
电压异常指示
指示灯常亮
指示灯常亮
指示灯呼吸
指示灯呼吸
指示灯闪烁5S熄灭
指示灯熄灭
指示灯
样才能保证手机快速的无线充电。（大于4mm充电效率低，大于
6mm可能不能充电）
5、取下手机方式：
单击左右的任一按键，夹臂和底托都张开到最大，等待取出手机，如
果5秒内没有取出手机，支架会再次自动夹紧手机。
6、通电后产品如果不亮灯或闪烁、按键失灵、无线充不工作，夹子
不张开或合拢，以上情况请停止使用并退回销售商处理。
为符合Qi无线充电标准的设备无线充电。
无线充电器支持15W快充，通用苹果和安卓机型。
无线充电式感应：当带有无线充电的手机靠近充电器时，被感应到后
开左右夹臂自动夹紧手机，并同时启动无线充电。
异物检测式感应：当不带无线充电的手机靠近充电器时，被感应到后
开左右夹臂也会自动夹紧，可作手机支架用。
固定在汽车出风口处，360°全角度可调，你可随意地调整你的手机
方向。
电路保护功能：过流保护、过热保护、短路保护，
产品认证书：FCC,CE,ROHS
产品说明
1.本产品有蓄电功能，熄火后5分钟内仍可以开合臂夹两次，防止熄火后
无法打开臂夹的尴尬。
3.本产品采用左右夹臂和底托三轴联动全自动夹臂设计。
2.本产品防滑硅胶垫采用局部凹槽设计，可有效的避开手机按键。
4.本产品有循环散热孔，保护手机充电不发热。
出风口支架
根据汽车出风口叶片位置调整好出风口夹子支撑件和可旋转夹子组件的
位置；插入汽车出风口，根据叶片厚度选择锁紧开关档位；适用于大部
分汽车出风口一键锁紧。硅胶接触汽车，更紧更贴合更好保护汽车不刮
伤。
吸盘支架
将吸盘放置于合适的平面位置（中控台和档风玻璃），调整角度按下按
键使吸盘紧锁平面。
固定后可随意调节角度和前后距离。TPU吸盘+滴胶双重吸附，一键即
锁紧。
1.车载无线充支架 x1
2.USB线 x1
3.吸盘支架 x1
4.出风口夹子 x1
5.使用说明书 x1
1
6
7支撑臂角度调节
松紧旋钮
支撑臂可180°调整
无线充角度调节
松紧旋钮
压下紧锁支架与吸盘
平面安装吸盘
温馨提示：
以上小型圆形款式的出风口,
夹子不能完美适配。
通过按压调节夹子
可旋转的夹子配件
可调节的出风口支撑
2
3
4
5
8
1
Right arm clamp2
Left arm clamp
3Bottom bracket
4Wireless charging coil/indicator
5Wireless charging coil area
6Button
7Type-C charging port
8Nut
Adjust the position of the support part and the Rotatory vent-mount
according to the position of car outlets, install the machine to the car
outlet, select the locking switch gear according to the thickness of the
blades; Suitable for most automobile air outlet. The silicon rubber of
the clamp mouth contacts the air outlet, more tightly fits, better protects
the outlet not to be scratched.
Suction cup holder
Air vent mount
Position the sucker in the right position (dashboard and windshield),
adjust the angle, press the locking-key to make the sucker lock firmly.
After fixing, the angle and distance can be adjusted at will. (TPU
sucker + drop glue double adsorption, one-key to lock.)
1
6
7Support arm angle
adjusting knob
Support arm can be
adjusted by 180 °
Support arm length
adjusting knob
Holder and suction
mount locking switch
Suction mount
Not suitable for
round vents
Adjust the clip by pressing
Adjustable air
outlet support
Swivel clip fitting
2
3
4
5
8
Instructions for use
Lighting mode
Mode
Power on
Standby Indicator light is always on
Charging Indicator light breathing
Indicator light breathing
The indicator lamp flashes
for 5s and goes out
Indicator light off
Full Charged
Foreign object detected
Over temperature
protection status
Indicator light is always on
Indicator light
The dual-coil version supports charging Samsung Z-FILP phones
3.If the phone does not support wireless charging, the indicator will
flash and turn off for 5s (there may be part of the mobile phone
without wireless charging function can not be detected by this
product, the need to press the button to clamp the mobile phone.
4. In order to ensure the efficiency and stability of charging, the best
wireless charging distance is ≤4mm and can not penetrate the metal,
so need to avoid using metal or too thick mobile phone case, this
allows the phone to charge quickly and wirelessly . (Charging
distance ≥4mm is inefficient and ≥6mm may not charge)
5. The Way to remove the phone
Click any button on the left or right, clamp-arms and bottom support
are open to the maximum, waiting to take out the phone, if the phone
is not taken out within 5 seconds, the product will automatically clamp
the phone again.
6. If the product does not turn on the light or flicker, button and
wireless charging does not work, clamp-arms do not open or close,
please stop using and return to the seller for Solving the problem.
Wireless charging for devices that meet Qi wireless charging
standards.
Wireless charger supports 15W fast charging, Universal Apple and
Android models.
Wireless charging detective: when the mobile phone with wireless
charging function close to machine and be sensed, it will open the
left and right arm to automatically clamp the mobile phone, and
start wireless charging.
Foreign object detective: when a phone without wireless charging
function is close to the machine and be sensed, the machine opens
the clamp-arms and also automatically clamp the phone, it is used
as a normal phone stand without charging.
Fixed in the car air outlet, 360°adjustable, you can adjust the
direction of your phone at will.
Circuit protection function: over-current protection, overheat
protection, short circuit protection
Certification FCC,CE,ROHS
Product description
Product details
Packing list
1. This product has a built-in capacitor, after power off within 5 minutes
can still open the clamp arm twice, to prevent it can not open the
clamp-arms after the car stalled .
2. This product uses the clamp-arms and the bottom support_three-ax-
is linkage automatic clamp design.
3. The anti-slip silicone pad is designed with Partial slit design, which
will not block the keys of the mobile phone.
4. This product has a circular cooling hole, to protect mobile phone
charging does not heat.
1. Car wireless charging stand *1
2. USB cable *1
3. Suction cup holder*1
4. Air outlet clip *1
5. User Manual *1
Output power: 5W/7.5W/10W/15W (MAX)
Applicable mobile phone: 4.0-6.9 inches
Product size: 97.5 * 62 * 20.5mm
Net weight: 155.5g
Product introduction
Automatic wireless
Product parameters
Product name: X3
Operating frequency: 115K-205KHZ
Recommend Charging distance: ≤ 4mm
Input: 5V/2A, 9V/2A
car mount
User Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
-
1
-
2
