2. GR3660-TB3 開機下在電腦進入系統待命或是休眠裝態時，會一起進入待命狀態。當電腦恢復正常運
作，則 GR3660-TB3 也會一併回復到正常使用狀態。
3. 切換 RAID 設定的標準程序：
4. RAID 模式一旦設定完成，若要進行切換，因切換過程中將會清除硬碟中的資料，請務必先將硬碟
中的資料另行備份後再行切換。
產品示意圖與配件表
燈號說明
產品使用注意事項
GR3660-TB3
步驟1：請在 GR3660-TB3 連線到電腦後，一併打開電腦和 GR3660-TB3 的電源開關。
步驟2：請在藍燈恆亮時，將在 GR3660-TB3 背板上設定 RAID 設定的「切換開關」調到你所要的
設定位置。
步驟3：請使用頂針插入「重置鍵」，待前面板抽取盒上的閃爍藍紫燈結束、並轉成恆亮藍燈後鬆
開頂針。
步驟4：請您再做一次關、開 GR3660-TB3 電源的動作後，您已經改變、並重新設定了 GR3660-TB3
的 RAID。
1. 第一次使用本產品進行設定時，資料會被全數清除。請於硬碟置入前，確認硬碟已備份，避免資料
遺失。
6. 強烈建議除了使用 GR3660-TB3 的資料儲存功能外，請針對重要資料備份到另一個儲存裝置上或
遠端備份，雙重備份您重要的資料。若您儲存在 GR3660-TB3 的資料損毀或遺失，RAIDON 將不負任
何的責任。
V1.1 (Sep. 2018)
前視圖 背視圖
GR3660-TB3 主體 x1
快速安裝導引 x1
打開包裝外盒後，包裝內容應包含下列組件 :
產品配件表
Thunderbolt™ 連接線 x1
電源轉接器 x1
電源線 x1
螺絲及鑰匙
硬碟讀取燈A
硬碟抽取盒把手B
硬碟抽取盒鑰匙孔C
電源插座D
電源開關E
風扇F
Mini DisplayPortG
Thunderbolt™ 連接埠H
RESET 按鈕J
RAID 切換鈕I
請參照下列步驟，完成 GR3660-TB3 的硬體安裝 :
1. 請使用零件包內附的鑰匙插入鑰匙孔後，抽取盒門閂將會輕彈開啟，即可將硬碟抽取盒取出。
2. 將硬碟安裝到抽取盒上，並以零件包內附的螺絲加以固定,以避免不必要的移動對硬碟造成傷害。
硬體安裝
3. 硬碟安裝完成後，請將抽取盒平移放入主機內，並關上把手。
4. 透過機體背面的 RAID 模式開關，設定所要使用的 RAID 模式 (RAID 0 、RAID 1 或 JBOD)。
5. 將相關連接線接上，最後請接上電源轉接器。
電腦 Thunderbolt™ 連接埠
6. 硬體安裝完成。開啟電源後請透過作業系統進行後續格式化設定。請依照電腦作業系統指示進行
硬碟格式化，完成硬碟格式化後，便可以進行資料的讀寫。
5. GR3660-TB3 使用 12V/5A 規格 Adapter，請勿使用其他非原廠規格 Adapter 以免損壞機器及資料。
7.
a. 如機器啟動後，抽取盒燈號會由「紅燈恆亮 > 熄滅 >藍燈恆亮」燈號，即為完成機器安裝設定。
b. 如機器啟動後，抽取盒燈號如出現「紅燈恆亮 > 熄滅 >藍紫閃爍」燈號，請使用頂針插入「重置鍵」
3秒後鬆開頂針，待燈號由「藍紫閃爍」燈號轉變為「藍燈恆亮」燈號時，即為完成機器安裝設定。
8.
機器安裝設定完成後，即可依需求設定 RAID 模式，請參考「產品使用注意事項/3.切換 RAID 設定的
標準程序」，做 RAID 模式切換設定。
J
狀態 硬碟狀態燈
無硬碟 紅燈恆亮
硬碟故障 紅燈恆亮
硬碟閒置 藍燈恆亮
資料存取 藍燈閃爍
資料重建 - 來源碟 呼吸燈（藍燈）
資料重建 - 目標碟 呼吸燈（紫燈）
請先確認相關配件與產品本身是否有受損或是缺少配件，若有任何疑問，請與您的經銷商或業
務人員聯絡。
請前往官網-產品資料下載頁面 (http://www.raidon.com.tw/RAIDON2016/down-
load.php) 下載驅動程式以及其餘相關資源。
˙
˙
GR3660-TB3 Quick Installation Guide
After you open the outside box, please make sure the following items/parts are contented in the box:
the Indication of HDD Status
HDD access IndicatorA
Removable drive trayB
HDD tray key lockC
Power socketD
Power switchE
FanF
Mini DisplayPortG
Thunderbolt™ portH
Port RAID Dip-switchI
Reset ButtonJ
Product Diagram & the Contents of Product package
Hardware Installation
Important Notice
2. GR3660-TB3 will be forced to get into SLEEP mode while your Mac Computer is in either IDLE
or SLEEP mode.
5. We strongly recommend you to keep an extra copy at your important personal data other
than stored in your GR3660-TB3 product. Stardom will not be responsible of your data loss
problem.
3. The Standard Procedure to Switch RAID Setting:
4. A WARNING to you if you plan to delete or switch your original RAID setting：If you plan to delete or
switch your original RAID setting, please always duplicate your personal data before deleting or
changing it.
Step 1: Please first connect GR3660-TB3 to your Mac.
Step 2: Please set RAID Dip Switch to the position you choose.
Step 3: Please use the Key to press the hidden RESET key at the back-plate, hold and wait for
the end of Blue-
Purple LED blinking till a stable Blue light.
Step 4: Please turn off your GR3660-TB3, and re-turn it on again. You now have reset
GR3660-TB3 with a new RAID mode successfully.
1. Since GR3660-TB3 will delete all data files in your two HDDs/SSDs at its first-time use, please
be informed that you shall first save all your personal data files into a safe memory space
before starting setting your new GR3660-TB3 to avoid any data loss during your start-up
process.
Front View Rear View
GR3660-TB3
Main Unit x1
Quick Installation Guide x1
Contents of Product Package
Thunderbolt™ Cable x1
AC/DC Adapter x1
Power Cord x1
Screws and key
Please follow the following procedure to have your GR3660-TB3 installed:
1. Use the provided key in the Accessories Kit and inserted it into the Key Access Opening to
eject the Removable Drive Tray Latch and extract the Removable Drive Tray.
2. Mount your hard drives onto the removable drive tray and secure it with the screws included
in the accessory kit to avoid any damage to the hard drive due to accidental movements.
Hardware Installation
3. After installing two HDDs into Trays, please insert them into GR3660-TB3, and then latch
the handle.
4. Please switch RAID Dip-switch to JBOD mode at back-plate.
5. Please connect the Thunderbolt Cable, and then connect AC/DC Adapter to the product.
6. Please turn on power.
7.
a. After turning on power, the HDD/SSD Indicator will be changed with the following
sequence, Red > Off > Blue, and then, GR3660-TB3 is ready for use.
b. In case if the HDD/SSD Indicator shows Red > Off > Blue Flashing, please use a pin to press
the RESET Button for 3 seconds, and wait until the HDD/SSD Indicator is changed to Blue
from Blue Flashing, your GR3660-TB3 is then ready for use.
8. While your GR3660-TB3 is ready for use, please follow the instruction of “3. The Standard
Procedure to Switch RAID Setting ”in the Important Notice and set the RAID mode to what
you want. You could then start using your GR3660-TB3 now.
Computer Thunderbolt™ Port
5. GR3660-TB 3uses a 12V/5V AC/DC Adapter. Please do not use other non-certified Power
Adapter to avoid damaging to your GR3660-TB3.
J
Status LED Light Status
No HDD Red light always on
HDD failed Red light always on
HDD idle Blue light always on
Data access Blue light flashing
Rebuilding, Source HDD Breathing blue light
Rebuilding, Target HDD Breathing purple light
Please check the product and accessories for any defect or missing parts. If you have
any questions, please contact your product supplier.
Please visit the official website - Download page (http://www.raidon.com.tw/
RAIDON2016/download.php) to download drivers and other related resources.
˙
˙
Thank you for choosing this RAIDON product.
The information provided in this manual was checked before publication, but the actual product
specifications may have changed before shipping; Latest product specifications and updates can be
found at www.RAIDON.com.tw or through your sales representative. No separate notifications will
be provided by our company.
If you have any questions about RAIDON products or would like to receive the latest product
information, instruction manuals, or firmware, please contact [email protected] for
assistance.
All product-related content in this manual are copyrighted by RAIDON TECHNOLOGY, INC.
V1.1 (Sep. 2018)
V1.1
-
1
-
2
