Rotary Hammer
DH 38SS
Handling instructions
Keep for future reference
English
2
3
4
5
○
○
+
+
6
○
+++
○
+
○ ○
7
○ ○
○
○
○
○
8
9
10
11
12
13
501
2
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
63
65
66
67
68
69
48
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
64
95
96
97
98
92
99
100
101
102
103
104
105
106
107
108
14
1 331241 1
2 331243 1
3 991697 2 D4×20
4 981942 4 M6×25
5 331238 1
6 319572 1 S-25
7 331244 1
8 331242 2
9 990134 2
10 331240 1
11 331239 1
12 331237 1
13 991712 4 M6×25
14 956996 1 1AS-60
15 321843 1
16 331236 1
17 331222 1
18 313396 1
19 331223 1
20 331224 1
21 321835 1
22 331225 1
23 331227 1
24 321832 1
25 331228 1
26 331226 1
27 331232 2
28 331230 1
29 331229 1
30 331231 1
31 331233 1
32 331234 1
33 331235 1
34 986104 2
35 331221 1
36 326369 1
37 321285 1
38 6201DD 1
6201DDCMPS2L
39 325003 1
40 360875E 1 220V-230V
41 331252 1
42 953174 2 D5×55
43 340753E 1 220V-230V “44”
44 930703 2
45 331251 1 “86, 87”
46 331210 1 “47-49, 51-59”
47 331211 1
48 944109 2 3×3×8
49 331212 1
50 313050 1
51 6002DD 1
6002DDCMPS2L
52 331213 1
53 331214 1
54 321281 1
55 331218 10
56 331217 10
57 331215 1
58 331219 1
59 629VVM 1 629VVC2PS2L
60 331220 1
61 992803 2 M6×20
62 986940 4 M6×45
63
------------- 2
64 994192 6 M5×16
65 331245 1
66 878713 1
67 331207 1
68 331549 1
69 939540 1
70 331208 1
71 948391 1
72 6203DD 1
6203DDCMPS2L
73 996363 1 S-40
74 321274 1
75 331209 1
76 939299 1 M661
77 331253 1
78 307947 1 M6×12
79 331248 1
80 949556 1 M6
81 331247 1
82 331246 1
15
83 330209 1
84 945161 2
85 999043 2
86 958900 2
87 938477 2 M5×8
88 982631 1
89 608VVM 1 608VVC2PS2L
90 331254 1
91 331202 1
92 302089 4 D5×20
93 331203 1
94 331204 1
95 330216 1 270L
96 959141 1
97
------------- 1
98 500457Z 1
99 940778 1 D10.7
100 981974 1
101 313093 1
102 938307 1
103 959141 1
104 960266 1
105 984750 2 D4×16
106 331205 1
107 307028 2 D4×25
108 331547 1
501 331206 1
English
16
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce risk of electric shock.
CONTENTS
GENERAL POWER TOOL SAFETY WARNINGS ........................................16
ROTARY HAMMER SAFETY WARNINGS ..................................................18
SYMBOL .......................................................................................................19
SPECIFICATIONS ........................................................................................ 19
STANDARD ACCESSORIES .......................................................................19
OPTIONAL ACCESSORIES (sold separately)..............................................20
APPLICATIONS ............................................................................................21
PRIOR TO OPERATION ...............................................................................21
WHEN THE PUSH BUTTON DOES NOT OPERATE SMOOTHLY ..............22
HOW TO USE THE ROTARY HAMMER ......................................................23
DRILLING AND DRIVING-IN OPERATIONS FOR ANCHORS .....................23
HOW TO HANDLE A CORE BIT ..................................................................25
HOW TO REPLACE GREASE ......................................................................26
MAINTENANCE AND INSPECTION ............................................................26
SERVICE PARTS LIST .................................................................................28
English
17
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool.
Do not use a power tool while you are tired or under the infl uence of drugs,
alcohol or medication.
A moment of inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Carrying power tools with your fi nger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
English
18
b) Do not use the power tool if the switch does not turn it on and off .
Any power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may aff ect the power toolʼs
operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations diff erent from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a qualifi ed repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
CAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.
ROTARY HAMMER SAFETY WARNINGS
1. Wear ear protectors
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
4. Do not touch the bit during or immediately after operation. The bit becomes very
hot during operation and could cause serious burns.
English
19
5. Before starting to break, chip or drill into a wall, fl oor or ceiling, thoroughly confi rm
that such items as electric cables or conduits are not buried inside.
6. Always hold the body handle and side handle of the power tool fi rmly. Otherwise
the counterforce produced may result in inaccurate and even dangerous operation.
7. Wear a dust mask
Do not inhale the harmful dusts generated in drilling or chiseling operation. The
dust can endanger the health of yourself and bystanders.
SYMBOL
WARNING
The following show symbols used for the machine. Be sure that you understand their
meaning before use.
To reduce the risk of injury, user must read instruction manual.
SPECIFICATIONS
Voltage 220 V
Power input 950 W
Capacity
Drill bit: 38 mm
Core bit: 105 mm
No load speed 620 /min
Full-load impact rate 2800 /min
Weight (without cord, side handle) 6.4 kg
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package contains the accessories listed in the below.
Case (Molded plastic)
1
Side Handle
1
English
20
OPTIONAL ACCESSORIES (sold separately)
○
Through-hole drilling (Rotation + Hammering)
(1 Drill bit (hexagon shank)
Overall length: 280, 400, 505 mm
External dia.: 16, 19, 22, 25, 28, 32, 38 mm
○
Anchor hole drilling (Rotation + Hammering)
(3) Cotter
(1) Drill bit (taper shank)
External dia.: 11, 12, 14.3, 14.5,
17.5, 21.5 mm
(2) Taper shank adapter
+
+
Taper shank adapter Application drill bit
Morse taper (No. 1) Drill bit (taper shank) 11, 12, 14.3, 14.5, 17.5 mm
Morse taper (No. 2) Drill bit (tape shank) 21.5 mm
A-taper
Taper shank adapter formed A-taper or B-taper is provided
as optional accessory, but drill bit for it is not provided.
B-taper
○
Large dia. hole boring (Rotation + Hammering)
(2) Core bit (3) Core bit shank(Guide plate)(1) Center pin
+++
(1) Center pin
●
Applied to core bits from 38 mm to 105 mm
●
Applied to core bits 32 mm and 35 mm
NOTE
Do not use core bits 25 mm or 29 mm.
(2) Core bit
●
External dia. 25, 29, 32, 35, 38, 45, 54, 64, 79, 94, 105 mm
(with guide plate, not applicable to cores 25 mm or 29 mm)
(3) Core bit shank
●
Applied to core bits above 38 mm
●
Applied to core bits below 35 mm
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
他の言語で
- English: Hitachi DH38SS User manual
関連論文
-
Hitachi DH 40SC Handling Instructions Manual
-
-
-
-
-
-
Hikoki DH 14DSL ユーザーマニュアル
-
-
-