Hitachi DN 10DSA Handling Instructions Manual

Hitachi
ブランド
Hitachi
モデル
DN 10DSA
カテゴリー
コードレスドライバー
タイプ
Handling Instructions Manual
Handling instructions
Keep for future reference
English
Cordless Driver Drill
DN 10DSA
2
3
4
5
6
1
2
3
4
7
○
○
○
8
○
9
○
○
10
2A
502501
1
3
4
5
6
7
8
9
10
10
11
13
12
14
15
16
17
18
11
English
12
CONTENTS
GENERAL POWER TOOL SAFETY WARNINGS ........................................12
PRECAUTIONS FOR CORDLESS DRIVER DRILL ......................................15
SYMBOL .......................................................................................................15
SPECIFICATIONS ........................................................................................ 16
STANDARD ACCESSORIES .......................................................................16
OPTIONAL ACCESSORIES (sold separately)..............................................17
APPLICATIONS ............................................................................................17
BATTERY REMOVAL/INSTALLATION ........................................................18
CHARGING ..................................................................................................18
PRIOR TO OPERATION ...............................................................................19
HOW TO USE ...............................................................................................19
MAINTENANCE AND INSPECTION ............................................................ 20
SERVICE PARTS LIST .................................................................................21
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious
injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
English
13
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool.
Do not use a power tool while you are tired or under the infl uence of drugs,
alcohol or medication.
A moment of inattention while operating power tools may result in serious personal
injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the
tool.
Carrying power tools with your fi nger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off .
Any power tool that cannot be controlled with the switch is dangerous and must be
repaired.
English
14
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may aff ect the power toolʼs
operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations diff erent from those intended could result in a
hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the manufacturer.
A charger that is suitable for one type of battery pack may create a risk of fi re when
used with another battery pack.
b) Use power tools only with specifi cally designated battery packs.
Use of any other battery packs may create a risk of injury and fi re.
c) When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fi re.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, fl ush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualifi ed repair person using only
identical replacement parts.
This will ensure that the safety of the power tool is maintained.
CAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.
English
15
PRECAUTIONS FOR CORDLESS DRIVER DRILL
1. Always charge the battery at a temperature of 10-40°C. A temperature of less
than 10°C will result in over charging which is dangerous. The battery can not be
charged at a temperature greater than 40°C. The most suitable temperature for
charging is that of 20-25°C.
2. Do not use the charger continuously.
When one charging is completed, leave the charger for about 15 minutes before
the next charging of battery.
3. Do not charge the battery for more than 1 hour.
The battery will be fully charged in about 1 hour and charging should be stopped
when 1 hour has elapsed from commencement. Disconnect the charger power
cord from the receptacle.
4. Do not allow foreign matter to enter the hole for connecting the rechargeable
battery.
5. Never disassemble the rechargeable battery and charger.
6. Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric current and overheat. It
results in burn or damage to the battery.
7. Do not dispose of the battery in fi re.
If the battery is burnt, it may explode.
8. When drilling in wall, fl oor or ceiling, check for buried electric power cord, etc.
9. Bring the battery to the shop from which it was purchased as soon as the post –
charging battery life becomes too short for practical use.
Do not dispose of the exhausted battery.
10. Using an exhausted battery will damage the charger.
11. Do not insert object into the air ventilation slots of the charger.
Inserting metal objects or infl ammables into the charger air ventilation slots will
result in electrical shock hazard or damaged charger.
12. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the
sleeve is not tight, the bit may slip or fall out, causing injury.
SYMBOL
WARNING
The following show symbols used for the machine. Be sure that you understand their
meaning before use.
Read all safety warnings and all instructions.
English
16
SPECIFICATIONS
POWER TOOL
Model DN10DSA
No-load speed 600 / min
Capacity
Drilling
Wood 10 mm
Metal Steel: 10 mm, Aluminum: 10 mm
Driving Wood screw 4.5 mm (diameter) × 20 mm (length)
Rechargeable battery (EB7) Ni-Cd battery, 7.2 V
Weight 1.1 kg
CHARGER
Model UC7SB
Charging time Approx. 1 hour (at 20°C)
Charging voltage 7.2 V
Weight 1.0 kg
STANDARD ACCESSORIES
DN10DSA has two types which are designated as 1HC and SSK. For their respective
accessories, see the Table below.
DN10DSA
(1HC)
DN10DSA
(SSK)
1
Plus driver bit (No.2) (attached to
body
1
1
2
Battery (attached to body)
1
1
3
Charger (UC7SB)
1
1
4
Plastic case
—
1
English
17
OPTIONAL ACCESSORIES (sold separately)
1. Battery
2. Plus Driver Bit
Bit No.
Bit No. Screw Size
No.1 2 – 2.5 mm
No.2 3 – 5 mm
No.3 6 – 8 mm
3. Minus Driver Bit
aScrew Size
0.8 mm 4 mm
1 mm 5 – 6 mm
a
4. Drill Bit for steel
Diameter, 2 mm, 5mm, 6mm
5. Drill Bit for wood
Diameter, 10 mm, 13 mm
APPLICATIONS
○
Driving and removing of machine screws, wood screws, tapping screws etc.
○
Drilling of various metals.
○
Drilling of various woods.
English
18
BATTERY REMOVAL/INSTALLATION
1. Battery removal
Hold the handle tightly and push the battery
latch to remove the battery (See Fig.1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its
polarities (See Fig. 2).
CHARGING
Before using the driver drill, charge the battery as
follows.
1. Insert the battery in the charger.
Position the battery so that the nameplate
faces toward the ventilation slots of the
charger and press in the battery until it
comes into contact with the bottom plate.
(See Figs. 1 and 3)
2. Connect the charger power cord to the
receptacle.
Connecting the power cord will turn on the
charger (the pilot lamp lights).
CAUTION
If the pilot lamp does not light, pull out the power cord from the receptacle and
check the battery mounting condition.
About 1 hour is required to fully charge the battery at a temperature of about 20°C. The pilot
lamp goes off to indicate that the battery is fully charged.
CAUTION
If the battery is heated due to direct sunlight, etc., just after operation, the charger
pilot lamp may not light. At that time cool the battery fi rst, then start charging.
Rechargeable
battery
Latch
Fig. 1
Handle
Insert
Pull out
Rechargeable
battery
Latch
Push
Fig. 2
Insert
Rechargeable
battery
Pilot lamp
Hole for connecting the
rechargeable battery
Fig. 3
English
19
3. Disconnect the charger power cord from the receptacle.
4. Hold the charger tight and pull out the battery.
PRIOR TO OPERATION
1. Tool mounting
For keyless chuck
(1) Mounting the bit
After inserting a driver bit, etc. into the keyless drill
chuck, fi rmly grasp the ring and tighten the sleeve by
turning it toward the right (in the clockwise direction
as viewed from the front). (See Fig. 4A)
○
If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger
when the sleeve is tightened.
(2) Dismounting the bit
Firmly grasp the ring and loosen the sleeve by turning
it toward the left (in the counterclockwise direction as
viewed from the front). (See Fig. 4A)
For chuck wrench
Always use a chuck wrench to install a driver bit
or drill securely. As three chuck wrench holes are
provided, tighten the chuck evenly. (See Fig. 4B)
2. Confi rm that the battery is mounted correctly.
3. Check the rotational direction.
When the selector lever is set to the drill
rotates clockwise when viewed from the drill rear.
When set to
, the drill rotates counterclockwise.
(See Fig. 5) (The
and marks are provided
on the body)
CAUTION
When the trigger switch is depressed, the selector lever cannot be moved. Always
release the trigger switch to move the selector lever.
HOW TO USE
1. Switch operation
When the trigger switch is depressed, the tool
rotates. When the trigger is released, the tool
stops. (Fig. 6)
CAUTION
○
While operating the driver drill, take care not
to lock the motor.
Tighten
Loosen
Ring
Sleeve
Fig. 4A
Tighten
Loosen
Chuck
wrench
Fig. 4B
mark mark
Selector
lever
Fig. 5
Trigger switch
Fig. 6
English
20
○
If the motor is locked, immediately turn the power off . If the motor is locked for a
while, the motor of battery may be burnt.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull too will degrade effi ciency and cause possible motor malfunction,
sharpen or replace the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should
any of the screws be loose, retighten them immediately. Failure to do so could result in
serious hazard.
3. Cleaning on the outside
When the driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy
water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.
4. Storage
Store the driver drill in a place in which the temperature is less than 40°C and out of reach
of children.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Hitachi DN 10DSA Handling Instructions Manual

Hitachi
ブランド
Hitachi
モデル
DN 10DSA
カテゴリー
コードレスドライバー
タイプ
Handling Instructions Manual
PDFをダウンロードします
報告

他の言語で

関連論文

その他のドキュメント