2
3
9
15
21
27
33
39
ENGLISH
3
ENGLISH
IMPORTANT PRECAUTIONS
CAUTION!
CONSULT A PHYSICIAN BEFORE USING THIS EQUIPMENT. READ OWNER’S MANUAL BEFORE USE.
It is essential that this equipment is used only indoors, in a climate controlled room. If this equipment has been exposed to colder temperatures or
high moisture climates, it is strongly recommended that the equipment is warmed up to room temperature before first time use.
WARNING!
TO REDUCE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS:
SAVE THESE INSTRUCTIONS
When using a Stepper, basic precautions should always be followed, including the following:
Read all instructions before using this equipment. It is the responsibility of the owner to ensure
that all users of this equipment are adequately informed of all warnings and precautions.
This equipment is intended for commercial use. To ensure your safety and
to protect the equipment, read all instructions before operating.
DANGER!
TO REDUCE THE RISK OF ELECTRICAL SHOCK:
Always unplug the equipment from the electrical outlet immediately after using,
before cleaning, performing maintenance and putting on or taking o parts.
• At NO time should children under the age of 14 use the unit.
• Children over the age of 14 or disabled persons should not use the unit without adult supervision.
• Close supervision is necessary when the exercise device is
used by or near children or disabled persons.
• At NO time should pets or children under the age of 14 be closer to the unit than 10 feet.
• This product must be used for its intended purpose as described in this Owner’s Guide.
• Incorrect or excessive exercise may cause injury. If you experience any kind of pain,
including but not limited to chest pains, nausea, dizziness, or shortness of breath,
stop exercising immediately and consult your physician before continuing.
• Heart rate monitoring systems may be inaccurate. Over exercising may result
in serious injury or death. If you feel faint, stop exercising immediately.
• Keep hands and loose clothing away from moving parts.
• Do not wear clothes that might catch on any part of the unit.
• Always wear athletic shoes while using this equipment.
• Do not jump on the unit.
• At no time should more than one person be on unit while in operation.
• This unit should not be used by persons weighing more than specified in the OWNER’S
MANUAL SPECIFICATIONS SECTION. Failure to comply will void the warranty.
• To prevent electrical shock, never drop or insert any object into any opening.
• Never operate the unit if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or immersed in water.
• Keep power cord away from heated surfaces.
• Do not operate where aerosol (spray) products are being
used or where oxygen is being administered.
• Never operate the exercise device with the air opening blocked.
Keep the air opening clean, free, of lint, hair and the like.
• Do not remove the side covers unless instructed by Customer Tech Support.
Service should only be done by an authorized service technician.
4
ENGLISH
ELECTRICAL REQUIREMENTS
For your safety and to ensure performance, the ground on this circuit must be
non-looped (isolated). Please refer to NEC article 210-21 and 210-23. Failure to
follow these electrical requirements could void the Matrix limited warranty.
GROUNDING INSTRUCTIONS
DANGER!
The unit must be grounded. If it should malfunction or breakdown, grounding provides
a path of least resistance for electric current to reduce the risk of electric shock.
The unit is equipped with a cord having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances. Improper
connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify the plug provided with the product. If
it will not fit the outlet, have a proper outlet installed by a qualified electrician.
110 V UNITS
110 V units require the use of a 100-125 V, 60 Hz and a minimum of a 15A circuit, with a
non-looped (isolated) neutral/ground for power. This unit can be daisy-chained together
with up to 4 units per 15A circuit. Matrix daisy-chain cord adapters are sold separately.
220 V UNITS
220 V units require the use of a 216-250 V, 50 Hz and a minimum of a 15A circuit, with a
non-looped (isolated) neutral/ ground for power. This unit can be daisy-chained together
with up to 4 units per 15A circuit. Matrix daisy-chain cord adapters are sold separately.
DIGITAL TV
An additional power adapter is not needed for the add-on TV or consoles with the
integrated digital TV tuner. An RG6 coaxial cable with ‘F-type’ compression fittings will
need to be connected between the video source and each add-on digital TV unit.
POWER REQUIREMENTS
BATTERY CHARGE (LED CONSOLES)
The Stepper saves its battery charge by moving into a shutdown mode whenever STEP FASTER
appears on the display. If the user does not maintain a step rate above 35 steps per minute, then a
30-second shutdown process begins.
When the battery voltage is low, LOW BATTERY appears on the display if the unit is moving into the
shutdown mode. The following situation is the time to recharge the battery:
• If no one has used the unit for an extended period of time, the battery may need recharging.
• The unit continues to function with a low battery; however, user and program information is lost
once the user stops.
If the battery must be recharged, use the optional power adapter charging unit. The charger should
be connected to the Stepper for a minimum of eight hours to ensure a thorough charge. After a
completion of charge, the battery light turns from red into green (see illustration). If LOW BATTERY
still appears on the display after a full charge, the battery could be extinct. Please check with an
authorized service technician for replacing the battery.
CAUTION: The battery stored inside the unit contains hazardous materials to the
environment. Proper disposal of the battery is required by the local law.
FCC REGULATIONS (USA ONLY)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body.
5
ENGLISH
TOOLS REQUIRED:
F 6mm Allen Wrench
F 5mm Allen Wrench
F Phillips Screwdriver
ASSEMBLY
PARTS INCLUDED:
F 1 Main Frame
F 1 Stabilzer Tube
F 1 Stabilizer Tube Cover
F 1 Console Mast
F 1 Console Mast Cover
F 1 Console Mast Bracket
F 2 Upper Handlebars
F 2 Lower Handlebars
F 1 Pulse Grip Handlbar
F 1 Handlbar Joint Connector
F 1 Bottle Holder
F 1 Power Cord
F 1 Hardware Kit
Console sold separately
UNPACKING
Unpack the equipment where you will be using it. Place the carton
on a level flat surface. It is recommended that you place a protective
covering on your floor. Never open box when it is on its side.
IMPORTANT NOTES
• All video and power outlets must be functional the day of delivery /
assembly of the product. The client is responsible for any additional
installation charges associated with return visits.
• During each assembly step, ensure that ALL nuts and
bolts are in place and partially threaded.
• Several parts have been pre-lubricated to aid in assembly and usage. Please do not wipe
this o. If you have diculty, a light application of lithium grease is recommended.
WARNING!
There are several areas during the assembly process that special attention must be
paid. It is very important to follow the assembly instructions correctly and to make
sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the equipment could have parts that are not tightened and will seem
loose and may cause irritating noises. To prevent damage to the equipment, the
assembly instructions must be reviewed and corrective actions should be taken.
NEED HELP?
If you have questions or if there are any missing parts, contact Customer Tech Support.
6
B
I
E
6
F
G
G
H
J
L
6
K
D
B
6
A
C
B
6
ENGLISH
1
Hardware Qty
A
B
C
Bolt (M8x40L)
Lock Washer
Screw (M5x15L)
4
4
4
2
Hardware Qty
B
D
Lock Washer
Bolt (M8x16L)
8
8
3
Hardware Qty
B
E
F
G
H
I
Lock Washer
Bolt Set
Arc Washer
Bolt (M8x16L)
Lock Washer
Bolt (M8x45L)
2
2
8
7
3
2
4
Hardware Qty
J
K
L
Bolt (M8x20L)
Bolt (M8x25L)
Bolt (M5x10L)
4
2
2
ASSEMBLY COMPLETE
1
2
3
4
5
6
7
LCB Communication
Extension Power Wire
TV Power
Console Connect Wires
Ethernet
Coax
Ground Wire
1
7
6
5
4
3
2
7
ENGLISH
PROPER USAGE
MOUNTING THE STEPPER
1. Stand behind the unit.
2. While holding both of the rear
arm handles, place one foot on
the corresponding footpad. Wait
until the footpad comes to a stop
at the bottom of the stroke.
3. Then place your other foot
on the opposite pedal.
4. Your unit offers a variety of foot positions.
Moving your foot to the forward most
position of the foot pad increases your
step height, which will create a feel
similar to a step machine. Placing your
foot toward the back of the foot pad
decreases your step height and creates
more of a gliding feel, similar to a
smooth walk or run. Always make sure
your entire foot is secured on the foot
pad. The pedal motion is dependent.
5. To determine proper workout position,
stand on the pedal with your foot on
the center of the pedal. Keep your
knees slightly bent at all times.
BEFORE YOU BEGIN
LOCATION OF THE UNIT
Place the unit on a level and stable surface away from direct
sunlight. The intense UV light can cause discoloration on the
plastics. Locate your unit in an area with cool temperatures
and low humidity. Please leave a clear zone behind the unit
that is at least 24” (600 mm). This zone must be clear of any
obstruction and provide the user a clear exit path from the
machine. Do not place the unit in any area that will block
any vent or air openings. The unit should not be located
in a garage, covered patio, near water or outdoors.
LEVELING THE EQUIPMENT
Locate a level, stable surface to position the Stepper.
The Stepper has leveling feet located under the foot
support. If your Stepper wobbles in the location where you intended to use
it, loosen the lock nut on the adjusting foot and adjust the feet until stable.
Once level, lock the adjusting feet by tightening the lock nut to the frame.
WARNING!
Our equipment is heavy, use care and additional help if necessary when
moving. Failure to follow these instructions could result in injury.
FREE AREA
0.6 m (2 ft)
8
ENGLISH
USING THE HEART RATE FUNCTION
The heart rate function on this product is not a medical device. While
heart rate grips can provide a relative estimation of your actual
heart rate, they should not be relied on when accurate readings are
necessary. Some people, including those in a cardiac rehab program,
may benefit from using an alternate heart rate monitoring system
like a chest or wrist strap. Various factors, including movement of
the user, may affect the accuracy of your heart rate reading. The
heart rate reading is intended only as an exercise aid in determining
heart rate trends in general. Please consult your physician.
Place the palm of your hands directly on the grip pulse handlebars.
Both hands must grip the bars for your heart rate to register. It takes
5 consecutive heart beats (15-20 seconds) for your heart rate to
register. When gripping the pulse handlebars, do not grip tightly.
Holding the grips tightly may elevate your blood pressure. Keep
a loose, cupping hold. You may experience an erratic readout if
consistently holding the grip pulse handlebars. Make sure to clean
the pulse sensors to ensure proper contact can be maintained.
WARNING!
Heart rate monitoring systems may be inaccurate.
Over exercising may result in serious injury or death.
If you feel faint, stop exercising immediately.
MAINTENANCE
1. Any and all part removal or replacement must be performed by a qualified service technician.
2. DO NOT use any equipment that is damaged and or has worn or broken parts.
Use only replacement parts supplied by your country’s local MATRIX dealer.
3. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain
important information. If unreadable or missing, contact your MATRIX dealer for a replacement.
4. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to
smooth operating equipment as well as keeping your liability to a
minimum. Equipment needs to be inspected at regular intervals.
5. Ensure that any person(s) making adjustments or performing maintenance or
repair of any kind is qualified to do so. MATRIX dealers will provide service
and maintenance training at our corporate facility upon request.
WARNING
To remove power from the Stepper, the power cord must be disconnected from the wall outlet.
MAINTENANCE SCHEDULE
ACTION FREQUENCY
Unplug the unit. Clean entire machine using water and a mild soap or
other Matrix approved solution (cleaning agents should be alcohol and
ammonia free).
DAILY
Check all connecting joint areas for tightness of bolt assemblies. QUARTERLY
PRODUCT SPECIFICATIONS
ENDURANCE STEPPER
CONSOLE TOUCH PREMIUM LED LED / GROUP TRAINING LED
Max User Weight 182 kg / 400 lbs
Product Weight 116.9 kg / 257.7 lbs 115.1 kg / 253.8 lbs 114.4 kg / 252.2 lbs
Shipping Weight 133.2 kg / 293.7 lbs 131.4 kg / 289.7 lbs 130.7 kg / 288.1 lbs
Overall Dimensions
(L x W x H)*
114.3 x 78.7 x 179.1 cm /
45” x 31” x 70.5”
* Ensure a minimum clearance width of 0.6 meters (24”) for access to and passage around MATRIX equipment.
Please note, 0.91 meters (36”) is the ADA recommended clearance width for individuals in wheelchairs.
9
14
14
14 3 10
10
() NEC
210-21 210-23 Matrix
110 V
110 V 100-125 V60 Hz 15A () /
15A 4 Matrix
220 V
220 V 216-250 V50 Hz 15A () /
15A 4 Matrix
F RG6
()
STEP FASTER
35 30
LOW BATTERY
LOW BATTERY
FCC
FCC 15 B
FCC RF
FCC RF
20
11
F mm
F mm
F
F
F
F
F
F
F
F
F
F
F
F
F
F
/
12
B
I
E
6
F
G
G
H
J
L
6
K
D
B
6
A
C
B
6
1
A
B
C
(M8 x 40 L)
(M5 x 15 L)
4
4
4
2
B
D
(M8 x 16 L)
8
8
3
B
E
F
G
H
I
(M8 x 16L)
(M8 x 45L)
2
2
8
7
3
2
4
J
K
L
(M8 x 20 L)
(M8 x 25 L)
(M5 x 10L)
4
2
2
1
2
3
4
5
6
7
LCB
1
7
6
5
4
3
2
13
24” (600 mm)
60 cm（2 英尺）
14
()
5 15 20
/ MATRIX
MATRIX
/MATRIX
Matrix
()
ENDURANCE
TOUCH PREMIUM LED LED / GROUP TRAINING LED
182 / 400
116.9 / 257.7 115.1 / 253.8 114.4 / 252.2
133.2 / 293.7 131.4 / 289.7 130.7 / 288.1
( x x )*
114.3 x 78.7 x 179.1 /
45 x 31 x 70.5
* MATRIX 0.6 24
(ADA) 0.91 36
15
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
16
•
•
•
•
•
•
17
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
•
•
•
18
B
I
E
6
F
G
G
H
J
L
6
K
D
B
6
A
C
B
6
1
B
4
4
4
2
B
D
3
B
I
2
2
7
3
2
4
J
K
4
2
2
1
2
3
4
5
6
7
1
7
6
5
4
3
2
19
0.6 m（2 ft）
20
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
ページを読み込んでいます...
/