Register your
new device on
MyBosch now and
get free benefits:
bosch-home.com/
welcome
MMBH6...TW
超高速全營養調理機
[zf] 使用說明書
[en] Instruction manual
超高速全營養調理機 3
High performance blender 10
3
zf
用途
用途
本電器僅供家庭和居家環境使用。僅限將本電器在家用正常時間內供處
理家庭正常的食物量。請勿超過允許的最大量（請參閱“食譜”）。
本電器適用於攪拌液體或半固體食物、將新鮮水果和蔬菜切塊或切碎以
及將食物打成泥，並用於切碎冷凍食物（如水果）或打碎冰塊。本電器不得
用於處理其他物體或物質。
本電器僅限於海拔2000公尺以下在室溫環境的室內使用。
重要安全須知
請仔細閱讀以下說明並妥善保管此使用說明書以便日後查閱！將此電器
交給其他人時，應將這些說明書一併轉交。
若未遵守正確使用本產品的說明，製造商對任何由此所造成的損壞概不
承擔任何責任。
身體、感官或智力有缺陷的人士以及缺乏相關經驗和╱或知識的人士，
必須在負責其安全人員的監督下且了解電器安全及相關危險的人員指
導下才可使用本電器。請讓孩童遠離本電器及電源線，且不要任其使用
本電器。請勿讓兒童玩耍本電器。除非在監督下，否則不得由孩童進行清
潔及維護的工作。
W觸電和發生火災的危險！
■ 僅限依照規格銘板上的規格連接和操作本電器。電源線和╱或本電器
損壞時，請勿使用本電器。僅限由我們的客戶服務維修本電器，例如更
換損壞的電源線，以避免發生危險。
■ 切勿將電器連接到定時開關或可遠端遙控的插座。當電源打開時，請
勿讓本電器離開您的視線！
■ 請勿將本電器放置於爐具這類的熱源上方或附近。請勿將電源連接線
接觸任何熱源或是與尖銳物品磨擦。
■ 請勿將底座浸泡在水中或放入洗碗機清洗。請勿使用蒸汽清潔機清潔
本電器。切勿在雙手潮濕的情況下操作本電器。
■ 請在以下情況下，務必將電器與電源斷開：每次使用後、無人看管本電
器時、組裝前、拆卸前、清潔前以及出現故障時。
W受傷危險！
■ 更換配件或電器在操作期間要移動其他零件前，應關閉本電器並斷開
供電。
■ 切勿將手伸入已安裝的超高速全營養調理機內！切勿在沒有蓋上蓋子
的情況下使用超高速全營養調理機。
■ 處理鋒利的切割刀片、清空容器和清潔時應格外小心。
■ 在關閉本電器前，必須將旋轉開關朝逆時針方向轉到底（零段）。
■ 關閉後，傳動器仍會短暫運作片刻。請等到傳動器完全靜止為止。
■ 使用前必須完全組裝好本電器。
■ 本電器接通電源時切勿取下蓋子。
4
zf
重要安全須知
W燙傷危險！
■ 加入高溫液體時應格外小心。突然產生的蒸氣可能會導致液體從調理
壺中噴出。
■ 操作期間，請務必用手將蓋子按住，但勿將手放在食材投入口上！當您
在調理壺中處理高溫食材時，蒸氣將通過蓋子的食材投入口逸出。
W窒息危險！
請勿讓孩童將包材當做玩具玩耍。
W小心！
■ 確保超高速全營養調理機調理壺內無任何異物。切勿將物體（如刀具、
勺子）插入調理壺內。僅限將隨附的推料棒與蓋子一起搭配使用！
■ 我們建議本電器的開啟時間不要超過處理食材所需的時間。請勿空機
操作本電器。
W重要！
每次使用完後或長時間未使用重新使用時，必須徹底清潔本電器。
X“清潔和保養”參見第6頁
感謝您購買新的 Bosch 電器。您可以在本公
司的網頁上查看與本公司產品有關的進一步
資訊。
內容
用途 ������������������������������������������������������� 3
重要安全須知 ������������������������������������������ 3
總覽 ������������������������������������������������������� 4
首次使用前 ��������������������������������������������� 5
符號和標記 ��������������������������������������������� 5
零件和操作控制 �������������������������������������� 5
使用事項 ������������������������������������������������ 6
自動程序 ������������������������������������������������ 7
清潔和保養 ��������������������������������������������� 7
安全系統 ������������������������������������������������ 8
故障排除 ������������������������������������������������ 8
食譜 ������������������������������������������������������� 8
棄置 ������������������������������������������������������� 9
保固 ������������������������������������������������������� 9
總覽
X 圖 A
1 底座╱馬達
a 保護墊
b 傳動器
c 重設按鈕（超載保護裝置）
2 控制面板
a
/
開關
b 旋轉開關（含標記）
c 狀態顯示（LED指示燈）
d 標記
e 標記
f
/
按鈕
g 6個具有LED指示燈的程序選擇按鈕
3 調理壺
a Tritan調理壺
b 刻度
c 超高速全營養調理機調理刀
d 把手
e 把手蓋（拆卸式）
4 蓋子
a 提供給推料棒╱加入更多食材的食材
投入口
b 鎖帽（含刻度）
c 推料棒
5
zf
首次使用前
狀態顯示
用於顯示本電器狀態，並作為旋轉開關零段
的標記。
顯示螢幕
顯示螢幕亮起：本電器已開啟並可以使用
顯示閃爍：
– 本電器故障
– 調理壺未正確到位或已脫落
– 旋轉開關在開啟本電器時未在零段
– 電源供應中斷後
– 連續進行5½分鐘以上的操作
（手動模式）
旋轉開關
用於連續調節調理刀的速度。
段位
零段（標記指向狀態顯示）=靜止
最低速
最高速
小心！
本電器連續在
速度段位上進行操作5½
分鐘後將自動關閉，重新開啟電器後，最多只
能在 速度段位上再操作1-2分鐘。否
則，食物可能會過熱並損壞調理壺。
注意事項：
– 若旋轉開關未在零段、調理壺已脫落或者
電源已中斷，狀態顯示將會閃爍。首先將旋
轉開關轉到零段，然後再繼續操作。
– 旋轉開關的段位不影響使用
/
的功
能。
/
按鈕
用於切換到在短時間內運作的最大速度。按下
/
按鈕時，本電器將以最大的速度運作。
注意事項：自動程序運行時無法使用此功能。
配備 LED 指示燈的程序選擇按鈕
用於選擇和啟動自動程序。X“自動程序”參
見第7頁
開啟電器後，所有LED指示燈都會亮起。按
下按鈕後，所選的程序將啟動，本電器將自動
運 行 。
調理壺
用於處理最多2公升的食物。調理壺是由
Tritan製成。Tritan是一種非常堅固的塑膠，
沒有明顯的味道或氣味。
首次使用前
使用新電器前，請務必將其整個從包裝中取
出、清潔並加以檢查。
小心！
切勿操作損壞的機器！
■ 請從包裝中取出底座和所有配件，並除去
所有的包材。
■ 檢查所有零件是否完整以及是否有明顯
損壞現象。X圖 A
■ 首次使用前，請先徹底清潔並晾乾所有零
件 。 X“清潔和保養”參見第7頁
符號和標記
符號 涵義
請勿將調理壺暴露在80°C以
上的溫度。
蓋子的警告
■ 除非正確蓋上此蓋子，否則
請勿使用本電器。
■ 請勿將調理壺暴露在80°C
以上的溫度。
馬達的警告
■ 請勿在沒有橡膠墊的情況
下進行操作。
零件和操作控制
高速馬達
本台超高速全營養調理機配備高速馬達，馬達
轉速每分鐘高達43000轉。這不僅提供了特
別快速和高品質的攪拌效果，而且還可以加熱
食物。例如，使用 自動程序可以將低溫食
材製成熱湯。
注意事項：在
速度段位下，使用
/
按
鈕和某些自動程序時，超高速全營養調理機
將以最高的速度運行。為了避免食物進行不
必要的加熱，請將食材處理的時間縮短或將速
度調低。
/
開關
開啟和關閉電器。
6
zf
使用事項
小心！
請勿將調理壺暴露在80°C以上的溫度。
附鎖帽的蓋子
確保在處理過程中將調理壺蓋妥。如要加入
切碎或液體食材，請朝逆時針方向轉動並取
下鎖帽。
推料棒
可將黏附在邊緣或未朝向調理刀充分攪拌的
食材推入。為進行此操作，請朝逆時針方向轉
動鎖帽，然後將其取下並將推料棒放入食材投
入 口 。 X“使用推料棒”參見第6頁
安全系統
本電器具有各種安全系統。X“安全系統”參
見第8頁
使用事項
W 受傷危險！
– 未完成本電器的所有準備事項以及未將
調理壺正確放置在底座前，請勿插入主電
源插頭。
– 切勿將手伸入放置到位的調理壺內，並在
使用本電器前務必蓋妥蓋子。
注意事項：只有在調理壺已正確到位的情況
下，本電器才會運作。
X 圖 B
1. 將底座放在穩定和平坦的流理台上。將保
護墊放在底座上，注意扣位。
重要：切勿在沒有保護墊的情況下安裝調理
壺。
2. 將調理壺放在保護墊上。確保調理壺固定
在電器上。
3. 將需要處理的食材放入調理壺。
4. 將附有鎖帽的蓋子放置到位並按壓固定。
5. 將旋轉開關朝逆時針方向轉到底（零段）。
6. 將電源插頭插入主電源。使用
/
開關
開啟本電器。所有LED指示燈亮起。
7. 朝順時針方向緩慢轉動旋轉開關，直到達
到所需的速度。LED狀態指示燈亮起。
注意事項：使用程序按鈕X“自動程序”參見
第7頁。
8. 將食材處理到所需的濃度。
9. 將旋轉開關朝逆時針方向轉到底（零段）。
等到本電器靜止為止。
10. 使用
/
開關關閉本電器。拔下主電源
插頭。
11. 取下調理壺。取下蓋子。
12. 將攪拌過的食物倒入另一個容器中。
清潔所有零件。X“清潔和保養”參見
第7頁
加入更多食材
X 圖 C
1. 朝逆時針方向轉動並取下鎖帽。
2. 在食材投入口加入更多切碎或液體食材，
注意最大容量。
3. 戴上鎖帽，朝順時針方向轉動將其擰緊。
4. 將食材處理到所需的濃度。
X 圖 D
加入更多食材量：
1. 將旋轉開關朝逆時針方向轉到底（零段）。
等到本電器靜止為止。
2. 使用
/
開關關閉本電器。拔下主電源
插頭。
W 受傷危險！
本電器接通電源時切勿取下蓋子。
3. 取下蓋子。
4. 加入額外的食材。
5. 重新蓋上蓋子。
6. 將電源插頭插入主電源。使用
/
開關
開啟本電器。所有LED指示燈亮起。
7. 朝順時針方向緩慢轉動旋轉開關，直到達
到所需的速度。LED狀態指示燈亮起。
8. 將食材處理到所需的濃度。
使用推料棒
W 受傷危險！
切勿在沒有蓋上蓋子的情況下使用推料棒！
X 圖 E
1. 朝逆時針方向轉動並取下鎖帽。
2. 將推料棒放入食材投入口。
3. 沿著調理壺的角落和側邊推動推料棒，用
推料棒將食材推入超高速全營養調理機
調理刀。
4. 然後立即再次取出推料棒。戴上鎖帽，朝順
時針方向轉動將其擰緊。
注意事項：使用推料棒可以明顯提高攪拌效
果的品質。
7
zf
自動程序
使用瞬轉功能
■ 開啟電器後，按住
/
按鈕。
■ 按下
/
按鈕時，本電器將以最大的速
度運行。
■ 放開
/
按鈕。本電器將以先前所選的
速度重新啟動。
注意事項：當自動程序正在運行時，無法使用
瞬轉功能。
自動程序
本電器具有6個自動程序。按下相關按鈕後，
所選的程序將以預設的速度和處理的時間開
始並處理食材。製作完成後，程序將自動結束。
可以選擇以下程序：
程序
用於製作含有冷凍食材的
綠色冰沙和水果冰沙
用於製作豆漿。
用於製作熱湯
用於磨碎豆類和穀物或其
他乾燥食材。
用於製作冰淇淋和雪糕
清潔程序
小心！
自動程序
完成後，請勿重新啟動
程序。否則，食物可能會過熱並損壞調理壺。
請注意：�
– 僅限使用
自動程序處理低溫食材。
若加入高溫食材，溫度會升高太多。
– 只有在旋轉開關位在零段時才能啟動自
動程序。
– 重新按下相關的程序選擇按鈕或使用
/
開關關閉電器，便可隨時關閉自動
程序。
範例
製作莓果蜂蜜冰沙
（食譜X“莓果蜂蜜冰沙”參見第8頁）
X 圖 F
1. 將底座放在穩定和平坦的流理台上。將保
護墊放在底座上，注意扣位。
重要：切勿在沒有保護墊的情況下安裝調理
壺。
2. 將調理壺放在保護墊上。確保調理壺固定
在電器上。
3. 將需要處理的食材放入調理壺。
4. 將附有鎖帽的蓋子放置到位並按壓固定。
5. 將旋轉開關朝逆時針方向轉到底（零段）。
6. 將電源插頭插入主電源。使用
/
開關
開啟本電器。所有LED指示燈亮起。
7. 按下 程序選擇按鈕。按鈕上的
LED指示燈亮起。
8. 本電器將自動處理食材。
W 受傷危險！
本電器接通電源時切勿取下蓋子。
9. 本電器將自動結束處理。所有LED指示
燈亮起。
10. 使用
/
開關關閉本電器。拔下主電源
插頭。
11. 取下調理壺。取下蓋子。
12. 將製作完成的水果冰沙倒入玻璃杯內。
■ 清潔所有零件。X“清潔和保養”參見
第7頁
清潔和保養
建議在每次使用後務必徹底清潔本電器和個
別零件。
W 觸電危險！
– 清洗前拔出本電器的插頭。
– 請勿將底座浸泡在液體中或放入洗碗機
清洗。
– 請勿使用蒸汽清潔機。
W 受傷危險！
請勿徒手觸碰超高速全營養調理機的刀片。請
使用刷子。
小心！
– 請勿使任何含酒精或苯的清潔劑。
– 切勿使用尖銳、鋒利或金屬物體。
– 請勿使用具研磨性的抹布或清潔劑。
注意事項：
– 所有零件在使用過後應立即清潔。這將避
免殘留物變乾且可能侵蝕塑膠（例如香草
中的精油）。
– 處理胡蘿蔔等食物時，塑膠零件可能會變
色，但可以用幾滴食用油將其除去。
– 如要更輕鬆清潔調理壺，請從把手上取下
蓋子，並在晾乾後重新蓋上。
您將在圖 G中查看如何清潔各個零件的概
要。取下要清潔的密封件。
8
zf
安全系統
“ ” 程序
用於便捷的清潔。
■ 將空的調理壺安裝到本電器上。
■ 加入1.25公升的溫水和2滴洗碗精。
■ 將附有鎖帽的蓋子放置到位並按壓固定。
■ 重新開啟電器，然後按下 程序選
擇按鈕。
■ 本電器將自動執行預清潔並自動結束程
序 。
■ 使用
/
開關關閉本電器。拔下主電源
插頭。
■ 取下調理壺、附鎖帽鎖的蓋子和保護墊。
■ 如有必要，徹底沖洗所有零件並重新清潔。
（X圖 G）。
■ 清潔底座。
安全系統
啟動安全鎖和自動切斷
只有在調理壺已正確到位，當本電器已開啟
或在中斷電源後將旋轉開關轉到零段的情況
下，才能操作本電器。若調理壺在運行時脫落，
本電器將自動關閉。本電器在手動模式（連續
以速度 – ）下連續進行5½分鐘
的操作後將自動關閉。X“故障排除”參見
第8頁
超載保護裝置
若本電器過熱，馬達會自動關閉。
X“故障排除”參見第8頁
注意事項：啟動超載保護裝置時，可能會產生
輕微的異味。此並非故障現象。
故障排除
W 受傷危險！
在處理任何故障前，請拔下電源插頭。
注意事項：若電器操作錯誤、電子保險絲跳閘
或電器有缺陷，本電器將不再開啟。請先利用
以下資訊嘗試處理已發生的問題。
小心！
若無法排除故障，請聯絡客戶服務。
故障
本電器使用期間無法開啟或關閉電源。狀態
顯示閃爍。
可能原因
– 調理壺未正確到位、已脫落或已被取下。
– 接通電源或電源中斷後，旋轉開關未在零
段。
– 本電器在手動模式（速度 – ）
下連續進行超過5½分鐘的操作後將自
動關閉。
排除方式
■ 使用
/
開關關閉本電器。
■ 將調理壺正確放置。
■ 將旋轉開關朝逆時針方向轉到底（零段）。
■ 使用
/
開關開啟本電器。狀態指示燈
亮起。
故障
本電器使用期間無法開啟或關閉電源。
可能原因
超載保護裝置已啟動。
排除方式
■ 將旋轉開關朝逆時針方向轉到底（零段）。
■ 使用
/
開關關閉本電器。拔下主電源
插頭。
■ 取下調理壺。
■ 讓本電器冷卻約15-20分鐘，然後重新
開啟。
■ 若本電器未啟動，請將本電器倒置。按下底
部的重設按鈕（X圖 A-1c）。
■ 若重設按鈕卡住，請讓電器再次冷卻，稍後
再重新嘗試。
食譜
注意事項：
– 您可以在圖 H中查看包含其他應用範例
的表格。食物處理前應將其清潔並切碎。去
除較硬的部分，如去核和去皮。
– 食譜和應用範例也可以在沒有自動程序
的情況下進行。如要執行此操作，請使用旋
轉開關將速度從 增加至 ，並攪
拌所有食材，直到達到所需的濃度。
莓果蜂蜜冰沙
– 400公克冷凍覆盆子╱混合莓果
– 1根香蕉
– 500毫升牛奶
– 3湯匙檸檬汁
– 2湯匙蜂蜜
■ 讓覆盆子╱混合莓果融化。
■ 將去皮的香蕉切成小塊。
9
zf
棄置
■ 加入食材至超高速全營養調理機，然後蓋
上附有鎖帽的蓋子。
■ 按下
按鈕。
■ 結束自動程序後，可將冰沙立即端上桌。
基礎豆漿
– 200公克煮沸的大豆
– 800毫升溫水（40-50°C）
– 白糖或蜂蜜可使其有甜味
■ 將200公克煮沸的大豆加入已有800毫
升溫水（40-50°C）的調理壺內。蓋上附鎖
帽的蓋子並用力按壓。
■ 按下 按鈕
■ 一旦程序結束，即可將豆奶端上桌，可加入
糖或蜂蜜使其有甜味。
自製糯米粉
– 500公克糯米
■ 將糯米放入調理壺中，蓋上附鎖帽的蓋子
並用力按壓。
■ 取下鎖帽，將推料棒插入食材投入口。按下
按鈕，使用推料棒將食材推下。
■ 為了得到更好的處理效果，請讓攪拌食材
冷卻，然後再次運行切碎程序。
■ 將糯米粉倒入食品袋中，放入冰箱冷藏可
保存三到六個月。
覆盆子冰淇淋
– 1個未經處理的檸檬
– 150公克全脂優格
– 150公克糖霜
– 600公克冷凍藍莓
– 150毫升全脂冷牛奶
■ 加入食材至超高速全營養調理機，然後蓋
上附有鎖帽的蓋子。
■ 按下
按鈕並運行自動程序。
■ 若需要有更高的濃度，可將冰淇淋倒入另
一個容器放入冷凍室一段時間。
提示：冰淇淋也可以用其他冷凍莓果（例如覆
盆子、草莓或混合莓果）製作。
煎餅麵糊
– 300毫升牛奶
– 100公克麵粉
– 2個小型雞蛋
– 1撮鹽
– 1湯匙油（例如葵花籽油）
■ 加入食材至超高速全營養調理機，然後蓋
上附有鎖帽的蓋子。
■ 將旋轉開關設為 ，並攪拌所有食材
30-60秒。
■ 將煎餅麵糊分次加入事先熱過和倒入油
的鍋中煎好。
番茄湯
– 750公克新鮮番茄或罐裝番茄
– 2個紅青椒
– 90公克腰果
– 6片羅勒葉
– 鹽和胡椒
■ 將新鮮的番茄洗淨，去除厚莖。
■ 加入食材至超高速全營養調理機，然後蓋
上附有鎖帽的蓋子。
■ 按下 按鈕並運行自動程序。
■ 結束自動程序後，將熱湯調味即可端上桌。
注意事項：若自動程序完成後湯品不夠熱，可
將旋轉開關轉至
，最多再攪拌1-2分鐘。
棄置
J
以環保方式處理包裝。此電器包含歐
盟關於使用過的電器及電子產品的指
令2012/19/EU（廢棄的電器及電子產
品 - WEEE）相關標籤。該指令包含歐
盟境內舊電 器退還及回收的規範。請
諮詢本地販售機構以瞭解棄置管道。
根據歐盟指令 2006/66/EC，有瑕疵
或沒電電池/可充電式電池必須使用環
保的方式分開進行回收。
保固
本電器的保修條款由銷售所在國家的代表機
構來制定。填寫並寄回隨電器附帶的保卡紙本
或至下方官網登錄註冊商品，即可享有2年保
固，保固條件請參照本公司公開資訊。
本公司保留隨時修改這些條款的權利。
www.bosch-home.com.tw/mybosch
10
en Intended use
Intended use
This appliance is intended for domestic use and the household
environment only. Use the appliance only for processing normal
amounts of food and for normal amounts of time for domestic use.
Do not exceed permitted maximum quantities (see “Recipes”).
This appliance is suitable for mixing liquid or semi-solid food, for
cutting or chopping raw fruit and vegetables, for puréeing food and
for chopping frozen food (such as fruit) or for crushing ice cubes.
The appliance must not be used for processing other substances
or objects.
Only use the appliance indoors at room temperature and up to
2000 m above sea level.
Important safety information
Read and follow the operating instructions carefully and keep for
later reference! Enclose these instructions when you give this
appliance to someone else.
If the instructions for correct use of the appliance are not observed,
the manufacturer’s liability for any resulting damage will be
excluded.
This appliance can be used by persons with reduced physical,
sensory or mental capabilities or lack of experience and/or
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved. Keep children away from the
appliance and connecting cable and do not allow them to use the
appliance. Do not let children play with the appliance. Cleaning and
user maintenance must not be performed by children.
W Risk of electric shock and fire!
■ Connect and operate the appliance only in accordance with the
specifications on the rating plate. Do not use the appliance if the
power cord and/or appliance are damaged. Only our customer
service may repair the appliance, e.g. by replacing a damaged
power cord, in order to avoid hazards.
■ Never connect the appliance to timer switches or remote-
controllable sockets. Never leave the appliance unattended while
it is switched on!
■ Do not place the appliance on or near hot surfaces, e.g. hobs.
The power cord must not come into contact with hot parts or be
pulled across sharp edges.
■ Never immerse the base unit in water or place it in the
dishwasher. Do not steam-clean the appliance. Do not use the
appliance with damp hands.
11
en
Important safety information
■ After each use, whenever the appliance is unsupervised, prior to
assembly, prior to disassembly, prior to cleaning and in the event
of an error, the appliance must always be disconnected from the
mains.
W Risk of injury!
■ Before replacing accessories or additional parts which move
during operation, the appliance must be switched off and
disconnected from the power supply.
■ Never reach into the attached blender! Never use the blender
without the lid in place.
■ Care should be taken when handling the sharp cutting blades,
emptying the container and during cleaning.
■ Before switching off, it is essential to turn the rotary selector in an
anticlockwise direction as far it will go (zero setting).
■ After switching off, the drive continues running for a short time.
Wait until the drive has come to a standstill.
■ The appliance must be completely assembled before use.
■ Never remove the lid while the appliance is plugged in.
W Risk of scalding!
■ Care should be taken when filling hot liquids. Sudden formation
of steam may cause the liquid to spurt out of the container.
■ You should always use one hand to hold the lid firmly in place
while you work, but don’t place your hand over the filling opening!
When you process hot ingredients in the jug, steam will escape
through the filling opening in the lid.
W Risk of suffocation!
Do not allow children to play with packaging material.
W Caution!
■ Check that there are no foreign objects in the blender jug. Do
not insert objects (e.g. knives, spoons) into the jug. Only use the
pusher provided with the lid on!
■ We recommend that the appliance is never switched on for longer
than is necessary to process the ingredients. Do not operate
at no-load.
W Important!
It is essential to clean the appliance thoroughly after each use or
after it has not been used for an extended period. X “Cleaning and
maintenance” see page 17
12
en Contents
Overview
X Fig. A
1 Base unit / Motor block
a Cushion pad
b Drive
c Reset button (overload protection)
2 Control panel
a
/
(on/off) switch
b Rotary selector with mark
c Status display (LED)
d (min) mark
e (max) mark
f
/
(Pulse) button
g 6 programme selection buttons
with LEDs
3 Blender jug
a Container made of Tritan
b Scale
c Blender knife
d Handle
e Handle cover (removable)
4 Lid
a Opening for pusher / for adding more
ingredients
b Locking cap with scale
c Pusher
Before using the appliance
for the first time
Before the new appliance can be used,
it must be fully unpacked, cleaned and
checked.
Caution!
Never operate a damaged appliance!
■ Remove the base unit and all
accessories from the packaging and
dispose of all packing materials.
■ Check that all the parts are present and
examine them for obvious damage.
X Fig. A
■ Thoroughly clean and dry all parts
before using for the first time.
X “Cleaning and maintenance” see
page 17
Contents
Intended use ............................................. 10
Important safety information .....................10
Overview...................................................12
Before using the appliance
for the first time ......................................... 12
Symbols and markings .............................13
Parts and operating controls.....................13
Use ...........................................................14
Automatic programmes ............................16
Cleaning and maintenance ....................... 17
Safety systems .........................................17
Troubleshooting ........................................ 17
Recipes.....................................................18
Disposal .................................................... 19
Guarantee.................................................19
Congratulations on the purchase of
your new Bosch appliance. You can find
further information about our products
on our web page.
13
en
Symbols and markings
Symbols and markings
Symbol Meaning
Do not expose the blender
jug to temperatures above
80°C.
Warnings on the lid
■ Do not use the appliance
unless this cover is
correctly attached.
■ Do not expose the blender
jug to temperatures above
80°C.
Warning on the motor block
■ Do not operate without
the rubber pad.
Parts and operating
controls
High-speed motor block
The blender is equipped with a high-speed
motor with a motor speed of up to 43000
revolutions per minute.This not only
provides particularly fast and fine blending
results but also makes it possible to heat
food. Using the (Soup) automatic
programme, for example, a hot soup can be
made from cold ingredients.
Note: At the
(max) speed setting, the
blender runs at the highest speed when
using the
/
(Pulse) button and with
certain automatic programmes. In order to
prevent unwanted heating of food, process
the ingredients for a shorter time or at a
lower speed.
/
(on/off) switch
To switch the appliance on and off.
Status display
To display the appliance status and as
a mark for the zero setting of the rotary
selector.
Display
Display lights up: appliance is switched
on and ready for use
Display flashes:
– fault in the appliance
– Blender jug is not correctly positioned
or has become detached
– Rotary selector not at zero setting
when switched on
– after interruption of the power supply
– longer than 5½ minutes of continuous
operation (manual mode)
Rotary selector
For continuous adjustment of the blender
knife speed.
Settings
Zero setting (mark points to the status
display) = standstill
(min)
Lowest speed
(max)
Highest speed
Caution!
When the appliance automatically turns off
after 51/2 minutes of continuous operation
at the
(max) speed setting, only use
the
(max) speed setting for another
1-2 minutes at the most after turning the
machine back on. Otherwise, the food
may heat up too much and damage the
container.
Notes:
– The status display flashes if the rotary
selector is not at the zero setting when
switched on, if the blender jug has
become detached, or if the electricity
supply has been interrupted. Turn the
rotary selector first to the zero setting
and then continue.
– The rotary selector setting does not
affect the use of the
/
(Pulse)
function.
14
en Use
/
(Pulse) button
For switching to the maximum speed
for a short time. The appliance works at
maximum speed while the
/
(Pulse)
button is pressed.
Note: The function cannot be used while an
automatic programme is running.
Programme selection buttons
with LEDs
For selecting and starting automatic
programmes. X “Automatic programmes”
see page 16
All LEDs light up after switching on. The
selected programme will start after pressing
the button and the appliance will run
automatically.
Blender jug
For processing up to 2 litres of food. The
blender jug is made of Tritan. Tritan is an
unbreakable plastic with no discernable
taste or smell.
Caution!
Do not expose the blender jug to
temperatures above 80°C.
Lid with locking cap
To securely close the blender jug
during processing. To add chopped or
liquid ingredients, turn the locking cap
anticlockwise and remove.
Pusher
To push ingredients that either stick to
the edge or do not blend well towards the
blender knife. To do so, turn the locking cap
anticlockwise, remove and place the pusher
into the opening. X “Using the pusher” see
page 15
Safety systems
The appliance has various safety systems.
X “Safety systems” see page 17
Use
W Risk of injury!
– Do not insert the mains plug until
all preparations for working with the
appliance are complete and the blender
jug has been correctly positioned on to
the base unit.
– Never put your hand in the blender jug
once it is in place, and always put the lid
on before using the appliance.
Note: The appliance will only work if the
blender jug has been correctly positioned.
X Fig. B
1. Place the base unit onto a stable and
level work surface. Position the cushion
pad on to the base unit, observing the
recess.
Important: Never attach the blender jug
without the cushion pad.
2. Place the blender jug on to the cushion
pad. Make sure the blender jug is firmly
positioned on the appliance.
3. Put the desired ingredients into the
blender jug.
4. Put the lid with the locking cap in place
and press it firmly.
5. Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting).
6. Plug the mains plug into the mains.
Switch on the appliance with the
/
(on/off) switch. All LEDs are lit.
7. Slowly turn the rotary switch clockwise
until the desired speed is reached. The
status LED lights up.
Note: Using the programme buttons
X “Automatic programmes” see
page 16.
8. Process the ingredients until the desired
consistency is achieved.
9. Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting). Wait until the appliance
comes to a standstill.
10. Switch off the appliance with the
/
(on/off) switch. Disconnect the
mains plug.
15
en
Use
11. Remove the blender jug. Remove
the lid.
12. Pour the blended food into another
container.
Clean all parts. X “Cleaning and
maintenance” see page 17
Adding more ingredients
X Fig. C
1. Turn the locking cap in an anticlockwise
direction and remove.
2. Add more chopped or liquid ingredients
through the opening, remembering to
observe the maximum capacity.
3. Put on the locking cap and tighten it by
turning in a clockwise direction.
4. Process the ingredients until the desired
consistency is achieved.
X Fig. D
Adding larger quantities:
1. Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting). Wait until the appliance
comes to a standstill.
2. Switch off the appliance with the
/
(on/off) switch. Disconnect the
mains plug.
W Risk of injury!
Never remove the lid while the appliance is
plugged in.
3. Remove the lid.
4. Add the extra ingredients.
5. Replace the lid.
6. Plug the mains plug into the mains.
Switch on the appliance with the
/
(on/off) switch. All LEDs are lit.
7. Slowly turn the rotary switch clockwise
until the desired speed is reached. The
status LED lights up.
8. Process the ingredients until the desired
consistency is achieved.
Using the pusher
W Risk of injury!
Never use the pusher without the lid
attached!
X Fig. E
1. Turn the locking cap in an anticlockwise
direction and remove.
2. Place the pusher provided into the
opening.
3. Push the ingredients with the pusher
towards the blender knife by guiding the
pusher along the corners and sides of
the blending jug.
4. Then remove the pusher again
immediately. Put on the locking cap
and tighten it by turning in a clockwise
direction.
Note: Using the pusher can considerably
improve the quality of the blending result.
Using the Pulse function
■ With the appliance switched on, press
the
/
(Pulse) button down and hold.
■ While the
/
(Pulse) button is
pressed, the appliance will run at
maximum speed.
■ Release the
/
(Pulse) button.
The appliance will start again with the
previously selected speed.
Note: While an automatic programme is
running, the Pulse function cannot be used.
16
en Automatic programmes
Automatic programmes
The appliance has 6 automatic
programmes. After pressing the relevant
button, the programme selected starts and
processes the ingredients at preset speeds
and processing times. The programme ends
automatically after preparation.
The following programmes can be selected:
Programmes
(Smoothie)
For green smoothies and
fruit smoothies with frozen
ingredients
(Soymilk)
For preparing soymilk.
(Soup)
For preparing hot soups
(Grinding)
For grinding beans
and grains or other dry
ingredients.
(Ice cream)
For ice cream and sorbets
(Cleaning)
Cleaning programme
Caution!
When the automatic programme
(Soup) has finished, do not restart the
(Soup) programme. Otherwise, the
food may heat up too much and damage
the container.
Please note:
– Only use cold ingredients with the
(Soup) automatic programme.
If hot ingredients are added, the
temperature increases too much.
– An automatic programme can only be
started when the rotary selector is at the
zero setting.
– An automatic programme can be ended
at any time by repressing the relevant
programme selection button or by
switching off with the
/
(on/off)
switch.
An example
Making a berry and honey smoothie
(recipe X “Berry and honey smoothie” see
page 18)
X Fig. F
1. Place the base unit onto a stable and
level work surface. Position the cushion
pad on to the base unit, observing the
recess.
Important: Never attach the blender jug
without the cushion pad.
2. Place the blender jug on to the cushion
pad. Make sure the blender jug is firmly
positioned on the appliance.
3. Put the desired ingredients into the
blender jug.
4. Put the lid with the locking cap in place
and press it firmly.
5. Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting).
6. Plug the mains plug into the mains.
Switch on the appliance with the
/
(on/off) switch. All LEDs are lit.
7. Press the (Smoothie)
programme selection button. The LED
on the button lights up.
8. The appliance processes the ingredients
automatically.
W Risk of injury!
Never remove the lid while the appliance is
plugged in.
9. The appliance ends processing
automatically. All LEDs are lit.
10. Switch off the appliance with the
/
(on/off) switch. Disconnect the
mains plug.
11. Remove the blender jug. Remove the
lid.
12. Pour the finished fruit smoothie into
glasses.
■ Clean all parts. X “Cleaning and
maintenance” see page 17
17
en
Cleaning and maintenance
Cleaning and maintenance
The appliance and the individual parts used
must be thoroughly cleaned after each use.
W Risk of electric shock!
– Unplug the appliance before cleaning it.
– Never immerse the base unit in liquids
and do not clean in the dishwasher.
– Do not use a steam cleaner.
W Risk of injury!
Do not touch the blender blades with your
bare hands. Use a brush.
Caution!
– Do not use any cleaning agents
containing alcohol or spirits.
– Do not use any sharp, pointed or metal
objects.
– Do not use abrasive cloths or cleaning
agents.
Notes:
– Clean all parts immediately after use.
This will prevent residues from drying
on and possibly attacking the plastic
(e.g. essential oils in herbs).
– When processing food such as
carrots, the plastic parts may become
discoloured, but this can be removed
with a few drops of cooking oil.
– To make cleaning the blender jug easier,
remove the cover from the handle and
replace once dry.
In Fig. G, you will find a summary of how to
clean the individual parts. Remove seal for
cleaning.
“ (Cleaning)” programme
For quick and easy cleaning.
■ Attach the empty blender jug on to the
appliance.
■ Fill it with 1.25 litres of warm water and
2 drops of washing-up liquid.
■ Put the lid with the locking cap in place
and press it firmly.
■ Switch the appliance on again and press
the (Cleaning) programme
selection button.
■ The appliance runs through automatic
pre-cleaning and ends the programme
automatically.
■ Switch off the appliance with the
/
(on/off) switch. Disconnect the
mains plug.
■ Remove, the blender jug, the lid with
locking cap and the cushion pad.
■ Rinse all parts thoroughly and clean
again if necessary. (X Fig. G).
■ Clean the base unit.
Safety systems
Start lock-out and
automatic cut-out
The appliance can only be operated if the
blender jug has been correctly positioned
and if the rotary selector is turned to
the zero setting when switching on the
appliance or after an interruption in the
power supply. The appliance will switch off
automatically if the blender jug becomes
detached while it is running. The appliance
automatically switches off in manual
mode (speed (min) – (max))
after 5½ minutes of continuous operation.
X “Troubleshooting” see page 17
Overload protection
The motor switches off automatically if the
appliance overheats. X “Troubleshooting”
see page 17
Note: When activating the overload
protection, a slightly strange smell may
occur. This is not a sign of malfunction.
Troubleshooting
W Risk of injury!
Before dealing with any faults, unplug the
mains plug.
Note: The appliance will no longer
switch on if there is an error in appliance
operation, if the electronic fuses trip or the
appliance has a defect. First try to eliminate
the problem which has occurred with
the help of the following information.
18
en Recipes
Caution!
If a fault cannot be eliminated, please
contact customer service.
Fault
Appliance fails to start up or switches off
while in use. The status display flashes.
Possible causes
– Blender jug is not correctly positioned,
has become detached or has been
removed.
– Rotary selector was not at the zero
setting when switching on or after an
interruption in power.
– The appliance was operating
continuously in manual mode (speed
(min) – (max)) for longer
than 5½ minutes.
Remedy
■ Switch off the appliance with the
/
(on/off) switch.
■ Position the blender jug correctly.
■ Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting).
■ Switch on the appliance with the
/
(on/off) switch. The status display
lights up.
Fault
Appliance fails to start up or switches off
while in use.
Possible cause
The overload protection device is activated.
Remedy
■ Turn the rotary selector in an
anticlockwise direction as far as it will go
(zero setting).
■ Switch off the appliance with the
/
(on/off) switch. Disconnect the
mains plug.
■ Remove the blender jug.
■ Leave the appliance to cool for approx.
15-20 minutes and then switch it on
again.
■ If the appliance does not start, turn the
appliance upside down. Press the reset
button on the bottom (X Fig. A - 1c).
■ If the reset button is blocked, leave the
appliance to cool again and try it again
later.
Recipes
Notes:
– In Fig. H, you will find a table with other
application examples. Clean and chop
food before processing. Remove hard
components such as cores and peel.
– The recipes and application examples
can also be carried out without an
automatic programme. To do this, use
the rotary selector to increase the speed
from (min) to (max) and
blend all the ingredients until the desired
consistency is reached.
Berry and honey smoothie
– 400 g frozen raspberries / berry mixture
– 1 banana
– 500 ml milk
– 3 tbsp lemon juice
– 2 tbsp honey
■ Let the raspberries / berry mixture thaw.
■ Cut the peeled banana into pieces.
■ Add the ingredients to the blender jug
and put on the lid with the locking cap.
■ Press the (Smoothie) button.
■ After ending the automatic programme,
serve the smoothie immediately.
Basic soymilk
– 200 g boiled soybeans
– 800 ml warm water (40-50 °C)
– White sugar or honey to sweeten to
preferred taste
■ Add 200 g boiled soybeans to the
blender jug with 800 ml warm water
(40-50 °C). Put on the lid with the
locking cap and press it firmly.
■ Press the (Soymilk) button
■ Once the program has finished, serve
the soymilk and add sugar or honey to
sweeten.
19
en
Disposal
DIY glutinous rice flour
– 500 g glutinous rice
■ Put the rice in the blender jug, put on
the lid with the locking cap and press
firmly.
■ Remove the cap and insert the pusher
into the opening. Press the
(Grinding) button and using the pusher
push down the ingredients.
■ For a better result, let the mixture cool
down and run the grinding program
again.
■ Pour Snow White into food bag and
keep in the fridge for up to three to six
months.
Raspberry ice cream
– 1 untreated lemon
– 150 g full-fat yoghurt
– 150 g icing sugar
– 600 g frozen blueberries
– 150 ml cold whole milk
■ Add the ingredients to the blender jug
and put on the lid with the locking cap.
■ Press the (IceCream) button
and run the automatic programme.
■ Pour the ice cream into another
container and put it into the freezer for a
while if a firmer consistency is desired.
Tip: The ice cream can also be made
with other frozen berries (e.g. raspberries,
strawberries or berry mixtures).
Pancake mixture
– 300 ml milk
– 100 g flour
– 2 small eggs
– 1 pinch salt
– 1 tsp oil (e.g. sunflower oil)
■ Add the ingredients to the blender jug
and put on the lid with the locking cap.
■ Set the rotary selector to (max)
and blend all the ingredients for
30-60 seconds.
■ Pour the pancake mixture in portions
into a hot and greased pan and fry.
Tomato soup
– 750 g fresh tomatoes or tinned tomatoes
– 2 red peppers
– 90 g cashew nuts
– 6 basil leaves
– Salt and pepper
■ Wash the fresh tomatoes and remove
the thick stem.
■ Add the ingredients to the blender jug
and put on the lid with the locking cap.
■ Press the (Soup) button and run
the automatic programme.
■ After ending the automatic programme,
season the hot soup and serve.
Note: If the soup is not hot enough once
the automatic programme has finished, turn
the rotary selector to
(max) and mix
for another 1-2 minutes at the most.
Disposal
J
Dispose of packaging in an environ-
mentally-friendly manner. This
appliance is labelled in accordance
with European Directive 2012/19/EU
concerning used electrical and
electronic appliances (waste electrical
and electronic equipment – WEEE).
The guideline determines the frame-
work for the return and recycling
of used appliances as applicable
throughout the EU. Please ask your
specialist retailer about current
disposal facilities.
Guarantee
The guarantee conditions for this appliance
are as dened by our representative in the
country in which it is sold. Details regarding
these conditions can be obtained from
the dealer from whom the appliance was
purchased. The bill of sale or receipt must
be produced when making any claim under
the terms of this guarantee.
Changes reserved.
限用物質含有情況標示
Declaration of the Presence Condition of the Restricted Substances Marking
設備名稱
Equipment
name
：
超高速全營養調理機
型號（型式）
Type designation
(Type)
：
MMBH6P6BTW
單元
Unit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛
Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr
+6
)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominate
d
diphenyl ethers
(PBDE)
內外殼
○ ○ ○ ○ ○ ○
馬達
○ ○ ○ ○ ○ ○
電路板
–
○ ○ ○ ○ ○
電源線
○ ○ ○ ○ ○ ○
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量
基準值。
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance
exceeds the reference percentage value of presence condition.
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference
value of presence.
備考3.〝－〞係指該項限用物質為排除項目。
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
