使用说明
AGRAS
User Guide
V1.0
2017.06
Obstacle Avoidance Radar
ユーザーガイド
사용자 가이드
EN
2
Disclaimer
Thank you for purchasing Obstacle Avoidance Radar (hereinafter referred to as the “Product”). Read this
disclaimer carefully before using this Product. By using this Product, you hereby agree to this disclaimer
and signify that you have read it fully. Please use this Product in strict accordance with the manual and
be sure to pay attention to the Warnings. SZ DJI TECHNOLOGY CO., LTD., and its aliated companies
assume no liability for damage(s) or injuries incurred directly or indirectly from using, installing or retting
this Product improperly, including but not limited to using non-designated accessories.
DJI
TM
is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and its affiliated
companies. Names of products, brands, etc., appearing in this manual are trademarks or registered
trademarks of their respective owner companies. This Product and manual are copyrighted by DJI with
all rights reserved. No part of this Product or manual shall be reproduced in any form without the prior
written consent or authorization of DJI.
This disclaimer is produced in various languages. In the event of divergence among dierent versions,
the Chinese version shall prevail when the Product in question is purchased in China, and English
version shall prevail when the Product in question is purchased in any other region.
Warning
1. The Obstacle Avoidance Radar is only compatible with the AGRAS
TM
MG-1S. DO NOT use it with
other products.
2. The Obstacle Avoidance Radar can be used with at farmland only and cannot be used with slope
elds where height dierences may occur.
3. To avoid interference, ensure that there is no other equipment using microwave radio frequencies
nearby. For example, automotive microwave radars, satellite communication stations, etc.
4. Before use, ensure that the outer protective cover is not cracked, chipped, sunken, or misshapen.
5. Keep the protective cover clean. Clean the surface with a soft damp cloth and air dry before using
again.
6. The obstacle avoidance functions are disabled in A-mode (Attitude).
7. Obstacle avoidance is adversely aected when aircraft pitch exceeds 15°. Please y with care.
8. Obstacle avoidance is disabled when ying over surfaces at a height of < 0.8 m.
9. Aircraft speed should not exceed 5 m/s when ying over surfaces at a height of < 2 m. Aircraft
speed should not exceed 7 m/s when ying at a height of ≥ 2 m. Obstacle avoidance will otherwise
be greatly compromised or even disabled.
10. Please maintain full control of the aircraft at all times. DO NOT rely solely on the DJI MG app. Keep
the aircraft within a visual line of sight observing it at all times. Use your discretion to operate it
manually to avoid obstacles.
11. DO NOT attempt to disassemble any part of the Obstacle Avoidance Radar that has already been
mounted prior to shipping.
EN
3
Introduction
The Obstacle Avoidance Radar is compatible with the Agras MG-1S. Microwave technology means
the radar is fully operational in dusty, misty, or nighttime conditions. It enables the aircraft to sense
obstacles in front of or behind it within 30 meters (refer to Specications for details), improving operation
safety. The DJI MG app will display obstacle information according to the orientation of the aircraft. A
built-in stabilized gimbal means that attitude changes cause no interference to the detection of angles.
Additionally, front and rear obstacle detection can be switched when ying forward or backward.
In the Box
Obstacle Avoidance Radar ×1
Rubber Pad
×
1
Bracket A ×1
Screw Pack
Bracket B ×2
M3
×
5.5
M2
×
6
Installation
Hex keys for the following screws are required: M3×5.5, M3×8, M2×6.
1. Mount Bracket B to the outer mounting holes of Bracket A as shown below. Tighten the four M3×5.5
screws.
EN
4
2. Mount Bracket B to the Obstacle Avoidance Radar with Bracket A over the red dot as shown below
and tighten the four M3×5.5 screws.
Red Dot
60 - 70 mm
3. Unfasten the buckles on Bracket A then mount it to the left landing gear leg of the MG-1S. Note
that Bracket A should be placed about 60-70 mm above the landing skid tube (as shown) to avoid
inuencing the Obstacle Avoidance Radar. Fasten the buckles and tighten the four M3×5.5 screws.
1
2
EN
5
d. Remount the rear radar module to the aircraft. Be sure to install the washer rst, then tighten the
M3×8 screw.
4. Connect Obstacle Avoidance Radar cable to the rear radar module on the MG-1S.
a. Remove the M3×8 screw and washer from the rear radar module on the aircraft and pull the
module a little more to remove it. Handle the cable with care and retain the screw and washer for
mounting the module later.
b. Remove the two M2×6 screws, cover, and rubber pad on the middle of the rear radar module’s
inner side.
c. Attach the rubber pad to the Obstacle Avoidance Radar’s cable plug.
EN
6
Usage
Detection Range
The detection range of the Obstacle Avoidance Radar is depicted as follows. Note that the aircraft
cannot sense obstacles that are not within detection range. Please y with caution.
10°
10°
50°
50°
OR
OR
App Display
Ensure the Obstacle Avoidance Radar is correctly mounted. Power on the remote controller and then
the aircraft. Enter Operation View in the app, which displays information about detected obstacles.
Front obstacle information appears on the upper screen, and rear obstacle information appears on the
lower screen. Red, orange, yellow, and green bars indicate the distance of obstacles in succession.
The value indicates the distance between the aircraft and the nearest obstacle.
30FT
EN
7
Aircraft Actions
1. If obstacles are detected more than 6 m away from the aircraft during ight, it will slow down and
hover in place about 6 m away from the obstacle.
2. If obstacles are detected within 6 m from the aircraft during ight, the aircraft will immediately brake
and hover in place. Braking distance is required when stopping mid-ight. Observe the distance
between an obstacle and the aircraft at all times. If necessary, y in a dierent direction than the
obstacle to avoid a collision.
3. When the aircraft is in Smart Operation Mode (A-B Route) or F-mode (Route), it will pause the current
task and record a break point when slowing down. Users can resume operation after controlling the
aircraft to avoid the obstacles. Refer to the “Operation Resumption” section in “MG-1S User Manual”
for more details.
Disable Obstacle Avoidance Functions
When not in use, disable the obstacle avoidance functions in the DJI MG app. To do this, enter
Operation View, tap on top of the screen, then turn off the Obstacle Avoidance Radar in
Aircraft Settings.
Obstacle Sensor Range 1.5 - 30 m
FOV Horizontal: 50°, Vertical: 10°
Measuring Frequency 170 Hz
Power Consumption 5 W
Operating Frequency
24.050 GHz to 24.250 GHz
EIRP
19 dbm
Operating Environment Flat Farmland
Specications
This content is subject to change without priority.
Download the latest version from
http://www.dji.com/mg-1s
AGRAS and are trademarks of DJI.
Copyright © 2017 DJI All Rights Reserved.
CH
8
免责声明与警告
感谢您购买高精度雷达避障模块（简称“避障模块”）。在使用之前，请仔细阅读本
声明，一旦使用，即被视为对本声明全部内容的认可和接受。请严格遵守本文安装和
使用该产品，并务必重视注意事项。因用户不当使用、安装、改装（包含但不限于使
用非 DJI
TM
指定的零配件）造成的任何损失，深圳市大疆
TM
创新科技有限公司及其关
联公司将不承担任何责任。
DJI 是深圳市大疆创新科技有限公司及其关联公司的商标。本文出现的产品名称、品
牌等，均为其所属公司的商标或注册商标。本产品及文档为深圳市大疆创新科技有限
公司版权所有。未经许可，不得以任何形式复制翻印。
关于不同语言版本的免责声明可能存在的语义差异，中国以中文版为准，其他地区以
英文版为准。
注意事项
1. 避障模块仅适用于 MG-1S 农业植保机，切勿在其他产品上使用。
2. 避障模块适用于平坦的农田环境，无法在坡地和有明显落差的环境使用。
3. 为防止干扰，务必确保附近无其他微波设备，如汽车微波雷达、卫星通信站等。
4. 每次使用前，检查确保外层的保护罩完好，无破裂、凹陷或其他变形等情况。
5. 保持保护罩清洁。使用柔软的湿布擦拭保护罩表面，然后自然风干。
6. A 模式（姿态）下无法使用避障功能。
7. 飞行器俯仰角超过 15°会影响避障效果，请谨慎飞行。
8. 飞行器距离下方表面高度 < 0.8 m 时，无法使用避障功能。
9. 飞行器距离下方表面高度 < 2 m 时，飞行速度不可超过 5 m/s；高度 ≥ 2 m 时，飞
行速度不可超过 7 m/s。否则避障功能将受到严重影响甚至失效。
10. 请全程保持对飞行器的控制，切勿完全依赖 DJI MG App 提供的信息。请依靠肉
眼观察，合理判断飞行状况，及时躲避障碍物。
11. 切勿自行拆下出厂时已安装的任何部件。
CH
9
简 介
高精度雷达避障模块是一款适用于 DJI MG-1S 农业植保机的配件，采用微波测距技术
实现障碍物感知，可适应尘土、喷雾等恶劣作业环境，且支持夜间作业。避障模块根据
飞行器飞行方向可感知前方或后方 30 m 内的障碍物（详见规格参数），并在 DJI MG
App 中显示相应信息，以提升植保作业的安全性。内置增稳云台确保雷达探测角度不受
飞行器姿态变化的影响，同时根据飞行器前飞或后飞切换前方或后方障碍物探测。
物品清单
避障模块 ×1
橡胶垫 ×1
连接件 A×1
螺丝包
连接件 B×2
安 装
请自备适用于以下螺丝的内六角扳手：M3×5.5、M3×8、M2×6。
1. 按图示方向将连接件 B 安装至连接件 A 外侧的安装孔，拧紧 4 颗 M3×5.5 螺丝。
M3×5.5
M2×6
CH
10
60 - 70 mm
2. 如图所示，将连接件 B 安装至避障模块，注意使连接件 A 与避障模块上的红点在
同一侧，然后拧紧 4 颗 M3×5.5 螺丝。
3. 打开连接件 A 上的扣环，将其安装至 MG-1S 飞行器左侧起落架的支撑管上。注意
连接件 A 与起落架底管的距离为 60 - 70 mm（如图），否则将影响避障模块的使用。
关闭扣环，然后拧紧 4 颗 M3×5.5 螺丝。
1
2
红点
CH
11
1
2
d. 重新安装 MG-1S 后方雷达模块，务必先安装垫片，然后再拧紧 M3×8 螺丝。
4. 将避障模块的连接线连接至 MG-1S 飞行器的后方雷达模块。
a. 移除 MG-1S 后方雷达模块上的 M3×8 螺丝及垫片，然后稍加用力拆下该模块。
注意不要损坏连接线。妥善保管螺丝及垫片，以便安装时使用。
b. 移除后方雷达模块内侧中间的 2 颗 M2×6 螺丝及保护盖、橡胶垫。
c. 将橡胶垫装至避障模块连接线的插头处，然后将连接线接至 4 针接口，拧紧 2
颗 M2×6 螺丝。
CH
12
使 用
探测范围
避障模块的探测范围如图所示。如有障碍物处于该探测范围以外则飞行器无法感知障
碍物，此时应谨慎飞行。
10°
10°
50°
50°
App 界面显示
确保避障模块安装正确后，开启 MG-1S 遥控器，连接飞行器电源。进入 App 的作业
界面，屏幕将显示避障模块检测到的障碍物信息。前方障碍物信息将显示在屏幕上部，
后方障碍物信息将显示在屏幕下部。红色、橙色、黄色、绿色依次指示由近至远的障
碍物，数值表示最近处的障碍物与飞行器的相对距离。
10米
或
或
CH
13
飞行器动作
1. 飞行过程中，若在距飞行器 6 米外的探测范围检测到障碍物，则飞行器将减速，
然后在距离障碍物约 6 米处悬停。
2. 飞行过程中，若在距飞行器 6 米内的探测范围检测到障碍物，则飞行器将立即刹
车至悬停。飞行器完全停止需要一定的刹车距离，在此情况下用户应时刻关注飞
行器与障碍物的距离，必要时可操控飞行器向反方向飞行，以免发生碰撞。
3. 若飞行器处于智能作业模式（A-B 点作业）或 F 模式（航线作业），则减速过程中
飞行器暂停当前任务并记录中断坐标点。用户操控飞行器绕过障碍物后，可进行
作业恢复，详见《MG-1S 用户手册》的“作业恢复”章节。
关闭避障功能
若不使用避障功能，可在 App 中关闭。进入 App 作业界面，点击右上方的 图标，
在 植保机参数中关闭避障模块。
规格参数
障碍物感知范围 1.5 - 30 m
FOV 水平 50°，垂直 10°
测量频率 170 Hz
功耗 5 W
工作频段 24.050 至 24.250 GHz
发射功率（EIRP） 19 dbm
使用环境 平坦的农田环境
内容如有更新，恕不另行通知。
您可以在 DJI 官方网站查询最新版本
http://www.dji.com/mg-1s
微信扫一扫关注
大疆农业公众号
DJI 和 是大疆创新的商标。
Copyright © 2017 大疆创新 版权所有
14
JP
SZ DJI TECHNOLOGY CO., LTD.
DJI
TM
SZ DJI TECHNOLOGY CO., LTD. DJI
DJI DJI
1. AGRAS
TM
MG-1S
2.
3.
4.
5.
6. A Atti
7. 15
8. 0.8m
9. 2m 5m/s 2m
7m/s
10. DJI MG
11.
15
JP
Agras MG-1S
30m
DJI MG
1
1
A 1 B 2
M3 5.5
M2 6
M3 5.5M3 8M2 6
1. A B 4 M3 5.5
16
JP
1
2
2. A B
4 M3 5.5
赤い点
60 ～ 70mm
3. A MG-1S
A
60 70mm
4 M3 5.5
17
JP
d.
M3 8
4. MG-1S
a. M3 8
b. 2 M2 6
c.
18
JP
10°
10°
50°
50°
10M
マニュアルで飛行中（GPS)
散布済み面積
高効率散布 農作物からの高度
19
JP
1. 6m 6m
2. 6m
3. A - B F
MG-1S
DJI MG
1.5 30m
5010
170Hz
5W
24.050 24.250GHz
EIRP 19dBm
最新版は下記よりダウンロードしてください。
http://www.dji.com/mg-1s
AGRAS DJI
Copyright © 2017 DJI All Rights Reserved.
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
ページが読み込まれています...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
dji AGRAS MG-1S Series ユーザーガイド
- タイプ
- ユーザーガイド
- このマニュアルも適しています
他の言語で
- English: dji AGRAS MG-1S Series User guide
