Makita HW001G ユーザーマニュアル

HW001G

EN Cordless High Pressure

Washer INSTRUCTION MANUAL 12

ZHCN 充电式高压清洗机使用说明书 28

ID Pembersih Bertekanan Tinggi

Tanpa Kabel PETUNJUK PENGGUNAAN 44

MS Pencuci Bertekanan Tinggi

Tanpa Kord MANUAL ARAHAN 61

VI Máy Xịt Rửa Áp Lực Cao Cầm

Tay Hoạt Động Bằng Pin TÀI LIỆU HƯỚNG DẪN 79

TH   95

2

1

2

Fig.1

1

Fig.2

1

2

Fig.3

1

2

Fig.4

1

Fig.5

1

Fig.6

Fig.7

1

2

Fig.8

3

Fig.9

1

2

3

Fig.10

2 1

Fig.11

1

2

Fig.12

1

2

Fig.13

1

2

3

Fig.14

1

2

3

Fig.15

1

2

3

Fig.16

4

1

2

Fig.17

1

Fig.18

Fig.19

2

1

Fig.20

Fig.21

1

2

Fig.22

5

1

Fig.23

Fig.24

1

23

4

Fig.25

1

Fig.26

1

Fig.27

1

Fig.28

1

2

1

Fig.29

6

1

Fig.30

Fig.31

Fig.32

1

Fig.33

1

2

Fig.34

Fig.35

1

2

Fig.36

1

2

Fig.37

7

Fig.38

1

Fig.39

1

Fig.40

1 2 3

Fig.41

21

Fig.42

Fig.43

8

1

3

21416

17 20

18

19

21

22

23

15

4

5

6

7

8

9

10

11

12

13

Fig.44

Fig.45

9

1

2

Fig.46

Fig.47

Fig.48

Fig.49

Fig.50

Fig.51

Fig.52

10

Fig.53

Fig.54

2 3

1

Fig.55

Fig.56

Fig.57

Fig.58

1

2

Fig.59

Fig.60

11

Fig.61

12 ENGLISH

ENGLISH (Original instructions)

WARNING

• Machines shall not be used by children. Children should be

supervised to ensure that they do not play with the machine.

• This machine is not intended for use by persons (including chil-

dren) with reduced physical, sensory, or mental capabilities, or

lack of experience and knowledge.

• This machine has been designed for use with the cleaning agent

supplied or recommended by the manufacturer. The use of other

cleaningagentsorchemicalsmayadverselyaectthesafetyof

the machine.

• During use of high pressure cleaners, aerosols may be formed.

Inhalation of aerosols can be hazardous to health.

• Depending on the application, shielded nozzles can be used

for high pressure cleaning, which will reduce the emission of

hydrous aerosols dramatically. However, not all applications

allow the use of such a device. If shielded nozzles are not appli-

cable for the protection against aerosols, a respiratory mask of

class FFP 2 or equivalent may be needed, depending on the

cleaning environment.

• The employer shall perform a risk assessment in order to spec-

ify the necessary protective measures regarding aerosols,

depending on the surface to be cleaned and its environment.

Respiratory masks of class FFP 2, an equivalent or higher are

suitable for the protection against hydrous aerosols.

• High pressure jets can be dangerous if subject to misuse. The jet

must not be directed at persons, live electrical equipment or the

machine itself.

• Do not use the machine within range of persons unless they

wear protective clothing.

• Do not direct the jet against yourself or others in order to clean

clothes or foot-wear.

• Riskofexplosion–Donotsprayammableliquids.

• High pressure cleaners shall not be used by children or

untrained personnel.

13 ENGLISH

• Highpressurehoses,ttingsandcouplingsareimportantforthe

safetyofthemachine.Useonlyhoses,ttingsandcouplings

recommended by the manufacturer.

• To ensure machine safety, use only original spare parts from the

manufacturer or approved by the manufacturer.

• Alwaysbesurethatthemachineisswitchedoandbatterycar-

tridges are removed before carrying out any work on the tool.

• Do not use the machine if important parts of the machine are

damaged, e.g. safety devices, high pressure hoses, trigger gun.

• Always remove the battery cartridges when leaving the machine

unattended.

• Comply with the requirements of the local water supply

company.

• For European countries:

According to EN12729 (BA), the appliance can also be con-

nectedtothemainsdrinkingwatersupplyifabackowpreventer

valve with drain facility is installed in the supply hose.

SPECIFICATIONS

Model: HW001G

Max.owrate*1 7.0 L/min

Waterowrate*2 Mode 3 (High mode) 5.5 L/min

Mode 2 (Middle mode) 4.2 L/min

Mode 1 (Low mode) 3.0 L/min

Max. permissible pressure 11.5 MPa

Workingpressure*2 Mode 3 (High mode) 8.5 MPa

Mode 2 (Middle mode) 5.5 MPa

Mode 1 (Low mode) 3.0 MPa

Max. feed pressure 1.0 MPa

Max. feed temperature 40 °C

Max. suction height 1.0 m

Rated voltage D.C. 36 V - 40 V max

Dimensions(LxWxH)*3 344 mm x 383 mm x 520 mm

Net weight 10.3 - 13.4 kg

Water protection IPX5

*1:Whenusingthetriggergunwithoutthenozzles.

*2:Whenusingthevariospraynozzleandextension.

*3:Whenthehandleisfoldedandwithouthoses.

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydierfromcountrytocountry.

• Theweightmaydierdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

14 ENGLISH

Applicable battery cartridge and charger

Battery cartridge BL4020/BL4025/BL4040/BL4050F*/BL4080F*

*:Recommendedbattery

Charger DC40RA / DC40RB / DC40RC

• Someofthebatterycartridgesandchargerslistedabovemaynotbeavailabledependingonyourregionof

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Take particular care and attention.

Read instruction manual.

Do not connect to a potable water faucet.

Do not direct the jet at people including

yourself, animals, and live electrical

equipments.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Guaranteed sound power level according

to EU Outdoor Noise Directive.

SoundpowerlevelaccordingtoAustralia

NSWNoiseControlRegulation.

Intended use

This machine is intended for cleaning stubborn dirt by

using water jet. This machine is intended for both com-

mercial use and household use.

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-

tions, illustrations and specications provided with

this power tool. Failure to follow all instructions listed

belowmayresultinelectricshock,reand/orserious

injury.

Save all warnings and instruc-

tions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

15 ENGLISH

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However, users of pacemakers and other similar

medical devices should contact the maker of their

device and/or doctor for advice before operating

this power tool.

Personal safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions

will reduce personal injuries.

3. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

yourngerontheswitchorenergisingpowertools

that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

5. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action

can cause severe injury within a fraction of a

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and o. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

3. Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools.Suchpreventivesafetymeasuresreduce

the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

foroperationsdierentfromthoseintendedcould

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease.Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled. The entangle-

ment of cloth work gloves in the moving parts may

result in personal injury.

16 ENGLISH

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.Shortingthebatterytermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

may exhibit unpredictable behaviour resulting in

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool is maintained.

2. Never service damaged battery packs.Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

IMPORTANT SAFETY WARNINGS

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

serious injury.

Save all warnings and instruc-

tions for future reference.

WARNING – When using this product, basic pre-

cautions should always be followed, including the

following:

Work area safety

1. Keep operating area clear of all persons.

2. Do not overreach or stand on unstable sup-

ports. Keep good footing and balance at all

times.

3. Always place the high pressure washer body

on a level and stable surface. Avoid areas

where the ejected water will run or pool.

4. Before cleaning, check the surroundings and

objects to be cleaned. High pressure jets can

scrape away paint or other surface treatments

including toxic chemicals. Take the preventive

measures if necessary.

5. Be careful not to trip over by the hose of the

high pressure washer. Always be aware of the

conguration of the hose during operation.

6. During use, a small amount of water will come

out from the bottom of the high pressure

washer. Avoid locating the high pressure

washer in the areas where you don't want to

wet.

Personal safety

1. To protect against the jet and objects by the

jet, operators should wear appropriate cloth-

ing such as safety boots, safety gloves, safety

helmets with visors, hearing protection, etc.

2. Do not use the high pressure washer within

range of persons unless they wear protective

clothing.

3. To reduce the risk of injury, close supervision

is necessary when the product is used near

children.

4. If connection is made to a potable water sys-

tem, the system shall be protected against

backow.

5. Water that has owed through backow pre-

venter is considered to be non-potable.

Electrical safety

1. Never touch battery cartridges with wet hands.

2. Do not use the machine if the important parts

of the machine are damaged, e.g. safety

devices, high pressure hoses, or the trigger

gun.

Power tool use and care

1. Read all the instructions before using the

product.

2. Know how to stop the high pressure washer

and bleed pressures quickly. Be thoroughly

familiar with the controls.

3. High pressure jets can be dangerous if mis-

used. The jet must not be directed at people,

live electrical equipment, or the machine itself.

4. This machine is not intended for use by per-

sons (including children) with reduced physi-

cal, sensory, or mental capabilities, or lack of

experience and knowledge.

5. Children should be supervised to ensure that

they do not play with the appliance.

6. Do not spray ammable and/or toxic liquids.

This may cause an explosion, intoxication, or

damage to the machine.

7. Do not direct the jet against yourself or others

in order to clean clothes or foot-wear.

8. High pressure hoses, ttings and couplings

are important for the safety of the machine.

Use only hoses, ttings and couplings recom-

mended by the manufacturer.

9. Follow the instructions when changing

accessories.

17 ENGLISH

10. Keep handles dry, clean, and free of oil or

grease.

11. Stay alert – watch what you are doing.

12. Do not operate the product when fatigued or

under the inuence of alcohol or drugs.

13. Do not run the high pressure washer without

water for longer than one minute. It will dam-

age the motor, resulting in malfunction.

14. Always turn o the power and shut o the

water mains when leaving the high pressure

washer unattended.

15. Be wary of the kickback. The trigger gun

recoils when the high pressure jet is ejected

from the nozzle. Hold the trigger gun rmly to

prevent accidental injuries.

16. Check for damaged or worn parts before use.

Also make sure that the hose is properly con-

nected and there is no leakage during oper-

ation. Operating the machine with functional

defects may cause an accident.

17. This machine has been designed for use with

the cleaning agent supplied or recommended

by the manufacturer. The use of other cleaning

agents or chemicals may adversely aect the

safety of the machine.

18. Do not pull the hose to move the high pressure

washer body. This will damage the hose and

connecting parts and result in a short circuit

or functional defects.

19. Do not put heavy objects on the hose or let

vehicles drive over it.

20. Always discharge the residual pressure in the

trigger gun before disconnecting the hose.

21. When connecting the hose to the water mains,

observe the instructions of your local water-

works department or company.

22. If the high pressure washer is dropped or hits

against an hard object, be sure to check for

damage and crack. Using the high pressure

washerdamagedmaygeneratesmoke,re,or

cause electric shock, which result in personal

injury.

23. During use of high pressure cleaners, aerosols

may be formed. Inhalation of aerosols can be

hazardous to health.

24. Depending on the application, shielded noz-

zles can be used for high pressure cleaning,

which will reduce the emission of hydrous

aerosols dramatically. However, not all appli-

cations allow the use of such a device. If

shielded nozzles are not applicable for the pro-

tection against aerosols, a respiratory mask

of class FFP 2 or equivalent may be needed,

depending on the cleaning environment.

25. The employer shall perform a risk assessment

in order to specify the necessary protective

measures regarding aerosols, depending on

the surface to be cleaned and its environment.

Respiratory masks of class FFP 2, an equiv-

alent or higher are suitable for the protection

against hydrous aerosols.

26. Prevent unintentional starting. Ensure the

switch is in the o-position before connecting

to battery pack, picking up or carrying the

appliance.Carryingtheappliancewithyournger

on the switch or energizing appliance that have

the switch on invites accidents.

27. Disconnect the battery pack from the appli-

ance before making any adjustments, chang-

ing accessories, or storing appliance.Such

preventive safety measures reduce the risk of

starting the appliance accidentally.

28. Do not modify or attempt to repair the appli-

ance or the battery pack except as indicated in

the instructions for use and care.

29. Do not apply the water jet to the same area

continuously. The object may break and cause

an injury.

30. Do not wash the machine with the water jet of

this machine. The machine may break or parts of

themachinemaycomeoandcauseaninjury.

31. To avoid risk of electric shock, do not direct

the water jet against the machine while the

machine is turned on.

Battery tool use and care

1. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

onetypeofbatterypackmaycreateariskofre

when used with another battery pack.

2. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packsmaycreateariskofinjuryandre.

3. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.Shortingthebatterytermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If con-

tact accidentally occurs, ush with water. If

liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause

irritation or burns.

5. Do not use a battery pack or tool that is dam-

aged or modied.Damagedormodiedbatteries

may exhibit unpredictable behaviour resulting in

re,explosionorriskofinjury.

6. Do not expose a battery pack or tool to re or

excessive temperature.Exposuretoreortem-

perature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

batteryandincreasetheriskofre.

Service

1. Follow the maintenance instructions specied

in the manual.

2. To ensure machine safety, use only original

spare parts from the manufacturer or approved

by the manufacturer.

18 ENGLISH

3. Have your high pressure washer serviced by

a qualied repair person using only identi-

cal replacement parts. This will ensure that

the safety of the high pressure washer is

maintained.

4. In case of breakdown or malfunction of the

high pressure washer, immediately switch it o

and remove the battery cartridge(s). Contact

your local dealer or service center.

Additional safety warnings

1. Comply with the requirements of the local

water supply company.

2. Do not use the machine when there is a risk of

lightning.

3. When you use the machine on muddy ground,

wet slope, or slippery place, pay attention to

your footing.

4. Do not replace the battery in the rain.

5. Do not submerge the machine into a puddle.

6. Do not leave the machine unattended outdoors

in the rain.

7. When storing the machine, avoid direct sun-

light and rain, and store it in a place where it

does not get hot or humid.

8. Do not sit on the machine or use the machine

as a step stool. Doing so may cause accident or

malfunction of machine.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product.

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble or tamper with the battery

cartridge.Itmayresultinare,excessiveheat,

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge.Suchconductmayresultina

re,excessiveheat,orexplosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.Itmaycauseheating,catchingre,

burst and malfunction of the tool or battery car-

tridge, resulting in burns or personal injury.

17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

19 ENGLISH

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the machine

is switched o and the battery cartridges are

removed before adjusting or checking function on

the machine.

Installing or removing battery

cartridge

CAUTION: Always switch o the machine

before installing or removing of the battery

cartridge.

CAUTION: Hold the machine and the battery

cartridge rmly when installing or removing bat-

tery cartridge. Failure to hold the machine and the

batterycartridgermlymaycausethemtoslipo

your hands and result in damage to the machine and

battery cartridge and a personal injury.

CAUTION: Make sure that you lock the battery

cover before use. Otherwise, mud, dirt, or water may

cause damage to the product or the battery cartridge.

CAUTION: Always install the battery cartridge

fully. If not, it may accidentally fall out of the machine,

causing injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

CAUTION: Hold the battery cover rmly when

installing or removing the battery cartridge.

To install the battery cartridge;

1. Pull up the locking lever, and then open the battery

cover.

►Fig.1: 1. Battery cover 2. Locking lever

2. Align the tongue on the battery cartridge with the

slot on the machine, and then slide the cartridge until it

locks in place with a little click.

►Fig.2: 1. Battery cartridge

3. Close the battery cover and push it until it is

latched with the locking lever.

To remove the battery cartridge;

1. Pull up the locking lever and open the battery

cover.

2. Pull out the battery cartridge from the machine

while sliding the button on the front of the cartridge.

3. Close the battery cover and push it until it is

latched with the locking lever.

Battery check button

You can check the remaining battery capacity by press-

ing the battery check button.

►Fig.3: 1. Battery indicator 2. Battery check button

Battery indicator status Remaining

battery

capacity

On O Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE: The indicator lamp for remaining battery

capacity is just for a reference. The actual battery

capacitymaydierdependingontheusagecondi-

tions or ambient temperature.

NOTE:Thelampautomaticallygoesoafterafew

seconds.

NOTE: If two battery cartridges are installed, the

batteryinstalledontheleftsideisusedrst.

NOTE: If two battery cartridges are installed, the

machine automatically switches the battery when the

battery in use becomes empty.

NOTE: You can check the remaining battery capacity

without turning on the power switch.

20 ENGLISH

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

►Fig.4: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambienttemperature,theindicationmaydierslightly

from the actual capacity.

NOTE:Therst(farleft)indicatorlampwillblinkwhen

the battery protection system works.

Machine/battery protection system

The machine is equipped with a machine/battery

protectionsystem.Thissystemautomaticallycutso

power to the motor to extend machine and battery life.

The machine will automatically stop during operation if

the machine or battery is placed under one of the fol-

lowing conditions:

Overload protection

When the machine or battery is operated in a manner

that causes it to draw an abnormally high current, the

machine automatically stops and the speed indicator

blinksingreen.Inthissituation,turnthemachineo

and stop the application that caused the machine to

become overloaded. Then turn the machine on to

restart.

Overheat protection

When the machine is overheated, the machine stops

automatically and the speed indicator lights up in red. In

this case, let the machine and battery cool before turn-

ing the machine on again.

NOTE: The speed indicator blinks in red when the

battery is overheated.

Overdischarge protection

When the battery capacity is not enough, the machine

stops automatically and the speed indicator blinks in

red. In this case, remove the battery from the machine

and charge the battery or change the battery to fully

charged one.

Protections against other causes

Protection system is also designed for other causes that

could damage the machine and allows the machine to

stop automatically. Take all the following steps to clear

the causes, when the machine has been brought to a

temporary halt or stop in operation.

1. Turnthemachineo,andthenturnitonagainto

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the machine and battery(ies) cool down.

If no improvement can be found by restoring protection

system,thencontactyourlocalMakitaServiceCenter.

NOTICE: If the machine stops due to a cause

not described above, refer to the section for

troubleshooting.

Mode switching button

The speed can be changed in three levels. To change

the speed mode, press the mode switching button.

When you change the speed mode, the corresponding

speed indicators light up.

►Fig.5: 1. Mode switching button

NOTE: You cannot change the mode while the

machine is turned on. Change the mode when the

machineisturnedoandthebatteryisinstalledto

the machine.

NOTE: If the speed indicator lights up in red or blinks

in red or green, refer to the instructions for machine/

battery protection system.

Power switch

WARNING: Always turn o the main power

switch when not in use.

NOTICE: Do not turn the power switch forcibly.

This may cause the switch to malfunction.

To turn on the machine, turn the power switch clock-

wise,andtoturnothemachine,turnthepowerswitch

counterclockwise.

►Fig.6: 1. Power switch

NOTE: The battery indicators will light up for a few

seconds just after turning the machine on.

NOTE: If you install the battery cartridge to the

machine when the power switch is in the turned-on

position, the speed indicator blinks in green. Turn

thepowerswitchtotheturned-oposition,andthen

install the battery cartridge to the machine.

ページが読み込まれています...

Makita HW001G ユーザーマニュアル

Makita HW001G ユーザーマニュアル

関連論文

その他のドキュメント