Use hexagonal wrench to remove the
magazine cap by counter clockwise.
12g
www.kwcgun.com
KIEN WELL TOY INDUSTRIAL CO., LTD
SINCE 1978
MADE IN TAIWAN
CO2 Cartridge is not included
Turn the magazine cap a
out counter-clockwise
and place CO2 cartridge
B inside the magazine.
Rapidly turn the screw A clockwise when
piercing the cartridge in the magazine.
逆時針轉出彈匣底內件
後，置入小鋼瓶B，再
以順時針方向鎖緊彈匣
底內件A。當刺破鋼瓶
出氣時，請快速鎖緊。
4.
使用六角鈑手反時針方向取出彈匣底
內件。
3.
瞄準目標物扣引鈑機，即可擊發。
2.
將裝好B.B彈的彈匣插入槍身往上推
入，直到彈匣卡榫發出"卡嚓"為止。
1.不良的B.B彈是造成卡彈的原因，請使用
品質優良的KWC B.B彈。
2.當卡彈時，請盡可能先取出彈匣，再以不
傷槍管的軟質細棒(不可大於4.4mm直徑)
從槍口置入清除。
5.使用一段時間後，請再次用中性矽油脂潤
滑撞針及鈑機軸心。
4.當扣引鈑機時，此時B.B彈即同時在上膛
階段，不可扣引一半時又回復，因為如此
的動作，將有可能上膛兩發B.B彈。
1.
為了使擊發順暢，填裝方
法是讓B.B彈在彈匣中一粒接著一粒。
填裝B.B彈。
6.
最多可裝21粒。
7.
拉下滑粒。
可射擊 保險
5.
Maximum BB capacity is 21 rounds.
Load BBs one by one.
Loading BBs
Insert fully loaded magazine in the airgun
until you hear the sound of “CLICK”.
Press the button.
Release the magazine.
Pulling trigger will load BB in the barrel.
Therefore, please do not pull the trigger half
way and release the trigger. This action could
load 2 BBs in the pistol and cause jamming.
Bad quality BB is the main reason to cause
BB jam. Please use the best quality KWC
BB to avoid jamming problem.
3.空擊發易造成零件損耗，請避免此動作。
Please avoid dry firing, for it could cause
parts deformed or damage.
When BB jammed, first please release the
magazine from pistol then use a soft stick
(diameter no bigger than 4.4mm) to clear up
the barrel.
此低動能遊戲用槍是針對喜愛射擊運動的消費
者所開發。避免因使用方法不正確或改造所發生的
故障或事故，請務必詳讀說明書，正確的操作享受
愉快的射擊運動。
This airgun is intended for recreational or
training purposes.To prevent improper
handling, modification or alteration
causing malfunction or accident, please
read the owner’s manual carefully. Enjoy
the pleasant shooting experience by
proper operation.
1.除了發射時外，不要將手指頭掛在板機上。
2.選擇安全與適當標靶
3.在非使用期間，請保持保險關閉且退彈的狀態，就
算在非使用狀態，也要如同其己裝彈。
4.如任何的機械產品，槍的保險也可能失效。即使在
保險關閉的狀態下也請小心的操作此槍，請勿將槍
口對人。
5.千萬不要對堅硬或平坦表面、水面射擊，以避免跳
彈。
6.請妥善保管產品在未成年孩童無法伸手取得的場
所。
7.每次使用前後都應該檢查擋彈物，假如擋彈物表面
有磨損失效或是反彈時請停止使用。
8.請使用高品質BB彈，請勿使用 口徑大於4.4mm
表面不平滑的 重複使用過的BB彈 非本說明書指
名的發射物。
9.最高的使用及儲藏CO2小鋼瓶環境為50℃(122℉)以
內，高溫可能會造成CO2小鋼瓶過熱甚至爆炸。
10.檢查任何掉落之槍枝，以確保未影響其功能。
1.Do not put your finger on the trigger except shooting.
2.Please choose safe and proper target.
3.Please always keep the airgun on safe and unloaded when
not using.
4.Like all mechanical devices, an airgun safety can fail.
Always handle the airgun safely even when the safety is “on
safe”. Never point the airgun at any people.
5.Avoid ricochet. Never shoot at a hard or flat surface or at
water.
6.Keep the airgun out of reach for small children.
7.Your backstop should be inspected for wear before and
after each use. Discontinue use of the backstop if surface
shows signs of failure or ricochet.
8.Only use high quality 4.5mm steel BBs. Never use BB
diameter larger than 4.4 mmBB with unsmoothed surface
reused BB that has been firedincorrect projectiles not
design for this airgun
9.Do not expose CO2 cartridges to heat or store them at
temperatures above 50∘C(122∘F). CO2 cartridges may
over heat or explode at temperatures above 50∘C(122∘F).
10.Check any gun that has been dropped to ensure that its
function has not been affected.
AAKCMD40 INSTRUCTION MANUAL
AAKCMD40
系列說明書
台南市仁德區義林路168巷89號
NO.89, LN. 168, YILIN RD.,
RENDE DIST., TAINAN CITY
71752, TAIWAN (R.O.C.)
TEL+886-6-2798175
FAX+886-6-2798176
www.kwcgun.com
For your safefy, please read this manual carefuly before use.
AAK
CMS40
CAUTIONRelease all the gas in the
magazine when it will be unused for a long
period of time.
※注意:在長期不使用的狀態下，請將彈
匣內氣體洩放掉。
1. 按下卡榫
2. 取出彈匣
K08-00750-M5 2018 ©
BARREL TOW
FIRING PIN
MAGAZINE
MAGAZINE BASE
REAR GRIP WEIGHT
TRIGGER (REAR)
TRIGGER TOW
FIRING PIN
KG-42X CARTRIDGE
STAB NEEDLE(NEW)
VALVE CAP
VALVE
BARREL
CARTRIDGE STAB NEEDLE
PACKING(TEFLON)
GRIP SCREW
SPRING PIN
HAMMER CASE SCREW
E BUCKLE
TRIGGER BAR
SAFETY DISCHARGE NOSE
YA-3 PIN
(TRIGGER CONNECTOR PIN)
HAMMER CASE PIN
PIN (FRAME)
PIN (TRIGGER)
VALVE SPRING GASKET
TRIGGER BAR SPRING
FIRING PIN BUFFER SPRING
FIRING PIN SPRING
MAGAZINE CATCH SPRING
HAMMER SPRING
TRIGGER SPRING
PLUNGER GUIDE SPRING
TRIGGER TOW SPRING
VALAVE SPRING
MAGAZINE SPRING
RUBBER CHAMBER
O-RING
O-RING
O-RING
O-RING
O-RING
Do not display this pistol in public—it may confuse people and may be a crime.
Always wear eye
protection when
using airsoft.
★使用低動能遊戲用
槍前，請務必戴上
保護眼鏡或面罩。
★使用低動能遊戲用
槍 前，請務必詳
讀說明書內容。
Read the owner’s
manual before
using the airsoft.
Never brandish or aiming this airsoft at any
people or domestic animals. Brandish this
airsoft in public is dangerous and may be a
crime.
★請不要在公開場合使用低動能遊戲用槍，
也請不要拿低動能遊戲用槍對準人或動
物。
★不可攜帶低動能遊
戲用槍在公共場所
行走，請務必裝在
袋子或盒子內。
Always transport an
airsoft in a locked
carrying case.
Make sure it is
unloaded and on
safe.
★請不要由槍口向內
探視。
To Avoid accidental
discharge, do not
look directly into the
barrel.
★請確認後再發射BB彈方向，附近無人或動
物存在。
Always be aware of your surrounding
before and during shooting and select a
safe area for target practice.
Disassemble, modify, or alter of your airsoft
may cause malfunction, void your warranty
and may make it unsafe to use.
★不可任意改造或加工低動能遊戲用槍，私
自改造加工會造成產品損壞、保固失效，
導致使用上不安全，甚至觸法送辦。
Spare parts may be modified for quality improvement
And such modification may be without advance notice.
FRAME
GRIP
TRIGGER
PLUNGER GUIDE
MAGAZINE CATCH
MAGAZINE CATCH JOINT
SAFETY PLUNGER
SLIDE STOP SLEEVE
SLIDE STOP
HAMMER
SAFETY (L)
MAGAZINE FOLLOWER
GRIP (R)
GRIP (L)
VALVE PACKING
INNER BARREL GUIDE
AAKCMD40 系列零件表
AAKCMD40 SERIES PARTS LIST
AAKCMD40 SERIES EXPLORED VIEW
AAKCMD40 系列零件分解圖
警告
Z01
Z02
P02
P03
P04
P05
P06
P07
P08
P09
P10
P11/Z03
P12/Z04
P13
P14
P15
P16
P17
P18
P19
P20
上蓋
槍管導管
本體
握柄
鈑機
保險卡榫導件
彈匣卡榫
彈匣卡榫配件
保險定位軸
上蓋止動片軸
槍管導管
擊鐵箱(右)
擊鐵箱(左)
上蓋止動片
擊鐵
保險(左)
彈匣滑粒
內槍管導引件
槍柄(右)
槍柄(左)
UKG-01心棒蓋迫緊
Z05
Z06
Z07
Z08
Z09
Z10
Z11
撞針
彈匣
彈匣底座
握柄配重
鈑機配件
槍管連動件
鈑機連動件
B01
B02
B03
B04
B05
B06
撞針軸
KG-42X 氣瓶頂針(新規)
KM-42 槍管(銅)
心棒蓋
RKM系 心棒(二孔)
氣瓶頂針迫緊(TEFLON)
E01
E02
E03
E04
E05
槍柄螺絲
止付螺絲M10x20黑
彈簧梢
擊鐵箱螺絲
E型扣環
F01
F02
F04
F05
F06
F07
F08
鈑機連桿
保險釋放件
YA-3軸(鈑機連動件軸)
軸(擊鐵、擊鐵箱)
軸(本體箱)
軸(鈑機)
心棒壓簧墊圈
S01
S02
S04
S05
S06
S07
S08
S10
S11
S12
鈑機連桿壓簧
撞針緩衝扭簧
撞針扭簧
彈匣卡榫壓簧
擊鐵扭簧
鈑機配件扭簧
保險定位軸壓簧
鈑機連動件扭簧
心棒壓簧
彈匣壓簧
R01
R02
R03
R04
R05
R06
KM-47 HOP-UP 4.5 子彈迫緊
O形環 1X5
O形環 1X3
O形環 1X4
O形環 ∮0.8x∮11.3id 橘色
O形環 1.45x6.9id
U02
U1
U2
X1
六角鈑手
內槍管組件
氣瓶頂針組件
擊鐵箱組件
VALVE SET
INNER BARREL UINT
INNER VALVE UNIT
HAMMER UNIT
SLIDE
OUTER BARREL
OUTER BARREL
CHASSIS CASE (R)
CHASSIS CASE (L)
SOCKET SCREW M10X20
-
1
-
2
