Use hexagonal wrench to remove the
magazine cap by counter clockwise.
42
42
C
C
12g
www.kwcgun.com
KIEN WELL TOY INDUSTRIAL CO., LTD
SINCE 1978
MADE IN TAIWAN
CO2 Cartridge is not included
Turn the magazine cap a
out counter-clockwise
and place CO2 cartridge
B inside the magazine.
Rapidly turn the screw A clockwise when
piercing the cartridge in the magazine.
逆時針轉出彈匣底內件
後，置入小鋼瓶B，再以
順時針方向鎖緊彈匣底內
件 A 。當刺破鋼瓶出氣
時，請快速鎖緊。
4.
Maximum BB capacity is 14 rounds.
Load BBs one by one.
Loading BBs
Insert fully loaded magazine in the airgun
until you hear the sound of “CLICK”.
Press the button.
Release the magazine.
CAUTIONRelease all the gas in the
magazine when it will be unused for a long
period of time.
Pulling trigger will load BB in the barrel.
Therefore, please do not pull the trigger half
way and release the trigger. This action could
load 2 BBs in the pistol and cause jamming.
Bad quality BB is the main reason to cause
BB jam. Please use the best quality KWC
BB to avoid jamming problem.
When BB jammed, first please release the
magazine from pistol then use a soft stick
(diameter no bigger than 6mm) to clear up the
barrel.
Please avoid dry firing, for it could cause
parts deformed or damage.
此低動能遊戲用槍是針對喜愛射擊運動
的消費者所開發。避免因使用方法不正確或
改造所發生的故障或事故，請務必詳讀說明
書，正確的操作享受愉快的射擊運動。
This airsoft is intended for recreational or
training purposes.To prevent improper
handling, modification or alteration
causing malfunction or accident, please
read the owner’s manual carefully. Enjoy
the pleasant shooting experience by
proper operation.
READ THIS OWNER'S MANUAL COMPLETELY.
1.除了發射時外，不要將手指頭掛在板機上。
2.選擇安全與適當標靶
3.在非使用期間，請保持保險關閉且退彈的狀態，
就算在非使用狀態，也要如同其己裝彈。
4.如任何的機械產品，槍的保險也可能失效。即使
在保險關閉的狀態下也請小心的操作此槍，請勿
將槍口對人。
5.千萬不要對堅硬或平坦表面、水面射擊，以避免
跳彈。
6.請妥善保管產品在未成年孩童無法伸手取得的場
所。
7.每次使用前後都應該檢查擋彈物，假如擋彈物表
面有磨損失效或是反彈時請停止使用。
8.請使用高品質BB彈，請勿使用 口徑大於6mm
表面不平滑的 重複使用過的BB彈 非本說
明書指名的發射物。
9.最高的使用及儲藏CO2小鋼瓶環境為50℃(122
℉)以內，高溫可能會造成CO2小鋼瓶過熱甚至
爆炸。
10.檢查任何掉落之槍枝，以確保未影響其功能。
1.Do not put your finger on the trigger except shooting.
2.Please choose safe and proper target.
3.Please always keep the airsoft on safe and unloaded when
not using.
4.Like all mechanical devices, an airsoft safety can fail.
Always handle the airsoft safely even when the safety is “on
safe”. Never point the airsoft at any people.
5.Avoid ricochet. Never shoot at a hard or flat surface or at
water.
6.Keep the airsoft out of reach for small children.
7.Your backstop should be inspected for wear before and
after each use. Discontinue use of the backstop if surface
shows signs of failure or ricochet.
8.Only use high quality BB. Never use BB diameter larger
than 6mmBB with unsmoothed surfacereused BB that
has been firedincorrect projectiles not design for this
airsoft.
9.Do not expose CO2 cartridges to heat or store them at
temperatures above 50∘C(122∘F). CO2 cartridges may
over heat or explode at temperatures above 50∘C(122∘F).
10.Check any gun that has been dropped to ensure that its
function has not been affected.
1. 按下卡榫
2. 取出彈匣
3. 使用六角鈑手反時針方向取出彈匣抵內件。
5. 拉下滑粒。
7. 最多可裝14粒。
為了使擊發順暢，填裝方
法是讓B.B彈在彈匣中一粒接著一粒。
6. 填裝BB彈。
可射擊 保險
※注意:在長期不使用的狀態下，請將彈匣
內氣體洩放掉。
1.
將裝好B.B彈的彈匣插入槍身往上推入，
直到彈匣卡榫發出"卡嚓"為止。
2.瞄準目標物扣引鈑機，即可擊發。
1.不良的B.B彈是造成卡彈的原因，請使用品
質優良的KWC B.B彈。
2.當卡彈時，請盡可能先取出彈匣，再以不傷
槍管的軟質細棒(不可大於6mm直徑)從槍口
置入清除。
3.空擊發易造成零件損耗，請避免此動作。
5.使用一段時間後，請再次用中性矽油脂潤滑
撞針及鈑機軸心。
4.當扣引鈑機時，此時B.B彈即同時在上膛階
段，不可扣引一半時又回復，因為如此的動
作，將有可能上膛兩發B.B彈。
KC-42 系列 零件分解圖
2
注意事項
K08-00644-D4 2018 ©
KC-42 SERIES PARTS LIST
KC-42 系列 零件表
C
Do not display this pistol in public—it may confuse people and may be a crime.
Always wear eye
protection when
using airsoft.
★使用低動能遊戲用
槍前，請務必戴上
保護眼鏡或面罩。
★使用低動能遊戲用
槍 前，請務必詳
讀說明書內容。
Read the owner’s
manual before
using the airsoft.
Never brandish or aiming this airsoft at any
people or domestic animals. Brandish this
airsoft in public is dangerous and may be a
crime.
★請不要在公開場合使用低動能遊戲用槍，
也請不要拿低動能遊戲用槍對準人或動
物。
★不可攜帶低動能遊
戲用槍在公共場所
行走，請務必裝在
袋子或盒子內。
Always transport an
airsoft in a locked
carrying case.
Make sure it is
unloaded and on
safe.
★請不要由槍口向內
探視。
To Avoid accidental
discharge, do not
look directly into the
barrel.
★請確認後再發射BB彈方向，附近無人或動
物存在。
Always be aware of your surrounding
before and during shooting and select a
safe area for target practice.
Disassemble, modify, or alter of your airsoft
may cause malfunction, void your warranty
and may make it unsafe to use.
★不可任意改造或加工低動能遊戲用槍，私
自改造加工會造成產品損壞、保固失效，
導致使用上不安全，甚至觸法送辦。
Spare parts may be modified for quality improvement
And such modification may be without advance notice.
Z01
Z02
Z04
Z05
Z06
Z07
Z10
Z11
Z12
Z13
Z14
Z15
Z16
Z21
上蓋
撞針
彈匣底座
鈑機配件
彈匣
握柄配重
槍管導管
擊鐵箱(右)
擊鐵箱(左)
保險(左)
槍柄(左)
槍柄(右)
氣瓶底座
鈑機連動件
SLIDE
FIRING PIN
MAGAZINE BASE
TRIGGER JOINT
MAGAZINE CASE
REAR GRIP WEIGHT
OUTER BARREL
CHASSIS CASE (R)
CHASSIS CASE (L)
SAFETY (L)
GRIP (L)
GRIP (R)
CARTRIDGE BASE
TRIGGER CONNECTOR
P02
P03
P04
P05
P06
P07
P08
P09
P13
P16
P17
P30
P31
本體
握柄
上蓋止動片
鈑機
保險卡榫導件
彈匣卡榫
彈匣卡榫配件
擊鐵
彈匣滑粒
保險定位軸
上蓋止動片軸
槍管連動件(Z30)
心棒蓋迫緊
FRAME
REAR GRIP
SLIDE STOP CATCH
TRIGGER
PLUNGER GUIAE
MAGAZINE CATCH
MAGAZINE CATCH LOCK
HAMMER
MAGAZINE FOLLOWER
SAFETY PLUNGER
SLIDE STOP PLUNGER
BARREL CONNECTRO
VALVE PACKING
B01
B02
B11
B19
B33
B215
B465
FIRING PIN
YA-3 PIN
BARREL
VALVE CAP
PUNCTURE VALVE
PUNCTURE VALVE PACKING
VALVE
撞針軸
YA-3軸
槍管(BAX 專用)
心棒蓋
氣瓶頂針
氣瓶頂針迫緊
心棒
F01
F02
F05
F03
F04
F401
鈑機連桿
保險釋放件
軸
(擊鐵、擊鐵箱)
軸(本體)
軸(鈑機)
心棒壓簧墊圈
TRIGGER BAR
SAFETY DISCHARGE NOSE
HAMMER CASE PIN
FRAME PIN
TRIGGER PIN
VALVE SPRING GASKET
S01
S02
S03
S05
S06
S07
S401
S404
SM4
SM5
鈑機連桿壓簧
彈匣卡榫壓簧
撞針扭簧
擊鐵扭簧
撞針緩衝扭簧
保險定位軸壓簧
彈匣壓簧
心棒壓簧
鈑機連動件扭簧
鈑機配件扭簧
TRIGGER BAR SPRING
MAGAZINE CATCH SPRING
FIRING PIN SPRING
HAMMER SPRING
FIRING PIN BUFFER SPRING
PLUNGER GUIDE SPRING
MAGAZINE SPRING
VALVE SPRING
TRIGGER BAR SPRING
TRIGGER SPRING
R01
R02
R03
R04
R05
R06
R07
U1
U2
X1
內槍管組件
氣瓶頂針組件
擊鐵箱組件
子彈迫緊HOP-UP
O形環1X5
O形環1X3
O型環1X4
O型環
0.8X11.3id
O型環
1X7 NBR70
O形環
1.45X6.9id
RUBBER CHAMBER
O-RING
O-RING
O-RING
O-RING
O-RING
O-RING
E01
E02
E03
E04
E06
E07
槍柄螺絲
⊕ 2.3X6尖黑熱
E型扣環
止付螺絲M10X20 黑
彈簧梢
彈簧梢
GRIP SCERW
SCREW
E BUCKLE
SCREW
SPRING PIN
SPRING PIN
INNER BARREL UINT
PUNCTURE VAVLE UNIT
HAMMER UNIT
-
1
-
2
